Ethernet port on the modem, and connect the other end to the Ethernet port on the PC. RJ11 cable. The other end connects to the phone line port on the Telephone set. Figure 1 illustrates the connection relationship
Important Safety Warnings
(NEC), Installation should include bonding the screen of the coaxial cable to the earth at the building entrance per ANSI/NFPA 70, the National Electrical Code in particular Section 820.93. Grounding of Outer Conductive Shield of a Coaxial Cable.
Installation Follow the procedures below to install the hardware. Figure 1 illustrates the connection relationship. 1. Connect one end of the coaxial cable (not included) to the CABLE port on the modem, and connect the other end to the cable wall outlet. Be sure not to bend or over tighten the cables as this may strain the connector and cause damage. If you plan to connect the modem and television to the same wall outlet, you must use a cable line splitter (not included). 3. ETHERNET: This is where you connect the Ethernet RJ45 cable. The other end connects to the Ethernet port on the PC or NIC. 4. RESET button: Reset the device to factory defaults by pressing and holding the button for more than 10 seconds. 5. CABLE Connector: This is where you connect the coaxial cable (not included) that leads to the cable splitter (not included) or the cable wall outlet. 3. Connect one end of the Phone line cable to a VoIP port (Tel) on the modem, and connect the other end to the phone port of the phone set. 4. Connect one end of the DC power adapter to the POWER port on the modem, and connect the other end to an electric outlet on the wall.
Connectors on the rear panel of the Modem This list of connectors describes where to connect the cables and power adapter when installing the cable modem. 1. POWER: This is where you connect the included power adapter. Remember to use only the power adapter that came with the Cable Modem. 2. Connect one end of the Ethernet cable to an 2. TEL: This is where you connect the phone line DS Green PleaseseetheLEDdescriptionsbelow: US Green
LED COLOR DESCRIPTION Power Green IndicatesthattheDevicehas successfullycompleted internalpowerontests.LED flashesifpoweronselftest Ready Green acquiringanIPAddressand ConfigurationFile. LEDwillremainoffifthecable modemconfigurationfilehas networkaccesssetto disable.TheLEDwillremain solidwhenthecablemodem isregisteredonthecable network. LEDMUSTremainsolid,when onhook LEDMUSTflashwhenaphone isOffhook Tel Green WPS Green LEDflasheswhenpushingthe HardwareWPS(attheright fails.
Indicatesthatdataisbeing receivedfromthecable network.Indicatesthatthe cablemodemhasacquireda DSchannel. Indicatesthatdataisbeing transmittedtothecable network.Indicatesthatthe cablemodemhasacquiredan upstreamchannel LEDwillflashslowlywhen performingupstreamranging. LEDwillflashquicklywhen 3 WLAN Green Ethern Green et sideofCPE)button.
WhenWifinetworkis available,LEDwillbeon. Indicatesconnectivity betweentheEthernetporton thecablemodemandthePCs Ethernetport.LEDflashes whentrafficisbeingpassed.
Specification Operating Environment: 40 degree C max.
Safety Notices
1. When this device is placed upright with the aid of the stand, the stand must be fixed at a 90-degree angle to the cable modemotherwise the device will have the risk of tipping over. 2. "Installation" should include bonding the screen of the coaxial cable to the earth at the building entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93; Grounding of Outer Conductive Shield of a Coaxial Cable. 3. How to disconnect device. The power plug should be installed near the cable modem to be easily accessible. If the cable modem becomes damaged, disconnect the power plug from the AC wall outlet immediately."
Wall-Mount Installation You can mount this device on a wall using the two mounting brackets on the bottom of the device. We recommend that you use two round or pan head screws. 1. Install two screws on a flat surface using Figure 2 on the opposite page as a reference. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall. If you install the screws into drywall, use hollow wall anchors to ensure that the device does not pull away from the wall due to prolonged strain from the cable and power connectors. 2. Mount the device onto the wall. Use Figure 3 on the opposite page as a reference:
Figure 2: The distance of the pothook
(Horizontal)
Figure 3: The screws size
Federal Communications Commission (FCC) Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, the device may cause harmful interference to radio communications. There is no guarantee, however, that interference will not occur in a particular installation. If this device causes harmful interference to radio or television reception, which can be determined by turning it off and on, the user can try to correct the interference by one of the following measures:
- Increase the separation between the device and the equipment with which it is interfering (for example, a television or radio).
- Connect the device into an electrical outlet on a different circuit is connected.
- Consult the dealer or an experienced radio/TV technician for help. interfered device than the
FCC Regulatory Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for 4 540.00771.005 5 6 compliance could void the user's authority to operate this device. IEEE 802.11b or 802.11g operation of this device in the U.S.A. is firmware-limited to channels 1 through 11.
FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated at a minimum distance of 20cm between itself and your body. This device must not be co-located or operating in conjunction with any other antenna or transmitter.