FCC ID: XCNUBC1329 DOCSIS 3.1 Advanced WiFi 6 Voice Gateway

UBC1329AA00 DOCSIS 3.1 Advanced WiFi 6 Voice Gateway Quick Installation Guide - Subscriber Model Name: UBC1329 UBC1329AA00 D3.1 WiFi 6 eMTA Quick Installation Guide Subscriber SAFETY NOTICES Grounding the Device: Install the cable modem to include grounding the coaxial cable to the earth as close as practical to the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with phase-to-phase voltage at 120V. This unit requires a 100-240V, 50/60Hz power adapter. Power adapter must be keyed for proper polarization, and must be fully inserted to contact the back of the power connector port to ensure snug connection. Do NOT use any other power adapter. Disconnecting the Device: If the cable modem becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. Temperature and Altitude: Install the device in a location not to exceed the maximum temperature of 104 Fahrenheit (40 Celsius). Regular operating altitude is 2000 m, and maximum operating altitude is 4500 m. PREPARING FOR INSTALLATION Locate the RF (coaxial) cable connector on the wall. Verify the power outlet is working and is wired correctly. Place your cable modem within a proper distance from the outlet. INSTALLING THE MODEM 1. Connect the coaxial cable (not supplied) to the CABLE connector on the rear panel of the modem and connect the other end to the cable wall outlet. Do not bend or over tighten the cables, as this may strain the connector and cause damage. To connect a modem and a television to the same wall outlet, you must use a cable line splitter (not included). 2. Connect an Ethernet cable (supplied) to one of the Ethernet ports on the back panel of the modem and connect the other end to the Ethernet port of a PC. Use a Category 5e or Category 6 Ethernet cable with RJ-45 connectors to ensure Gigabit Ethernet speeds (when the computer supports it). 3. Connect an RJ-11 phone cable (not supplied) to the TEL1 port on the modem (when provisioned for voice service as specied by the service provider), and connect the other end to the phone port of the telephone. If voice service is not provisioned through the service provider, telephone service is not available. 4. Connect the power adapter (supplied) to the PWR (power) port. Connect the other end to a power outlet. UBC1329AA00 Connect a PC or Ethernet enabled device (wireless switch or router). A PC should be connected for initial device installation and configuration. 2 3 RJ-45 RJ-11 Device must be installed vertically to obtain optimum wireless performance. 1 Cable/RF 4 1 www.ubeeinteractive.com DEVICE WALL MOUNT INSTRUCTIONS You can mount the UBC1329AA00 on a wall using the 2 mounting brackets on the side of the device. Two round or pan head screws are recommended. See the gure below for measurements. D UBC1329AA00 Quick Installation Guide 140mm (5.51 inches) Label Size in Millimeters (mm) A B C D 6.65 +/- 0.35 1.9 +/- 0.15 19.0 +/- 1.2 4 - 5 To mount the device on a wall:

1. Install the 2 screws horizontally on the wall 140 mm (5.5 inches apart. Note: The screws should protrude from the wall so you can t the device between the head of the screws and the wall. If you install the screws in drywall, use hollow wall anchors to ensure the unit does not pull away from the wall due to prolonged strain from the cable and power connectors. 2. Mount the device on the wall. NOTE to CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV systems installer's attention to section 820-93 of the National Electric Code, which provides guidelines for proper grounding and in particular, specify that the Coaxial cable shield shall be connected to grounding system of the building, as close to the point of cable entry as practical. www.ubeeinteractive.com 2 UNDERSTANDING DEVICE CONNECTIONS AND BUTTONS The rear and front panels of the UBC1329AA00 have the following connections and buttons:

RESET: Use to reset the device. Take a small object like the end of a paper clip and insert it into the RESET opening. To power cycle the device, hold for less than 5 seconds. To reset to factory default settings, hold for more than 20 seconds. The UBC1329AA00 will reset and reboot. WARNING: Resetting factory defaults will erase ANY and ALL settings that you have made and will restore the device to factory default settings. ETHERNET 1-4: Use to connect to an Ethernet-enabled devices such as computers, gaming consoles or a wireless access point

(LAN switch, router) using an RJ45 Ethernet cable. Each Ethernet port on the back panel of the device has two LEDs to indicate its status. See the LED Behavior section on the next page for details. CABLE: Use to connect to the coaxial cable from your Internet service provider. TEL1-TEL2: Use to connect analog telephones to the device. PWR: Use to connect to the power adapter. Plug the other end into the wall power outlet. WPS: Located on the front panel of the device, it is used for the Wi-Fi Protected Setup (WPS) method to connect a PIN-protected Wi-Fi device to the cable modem. When a user pushes the WPS button or triggers WPS via Web UI, ashes for 4 minutes until PIN is entered from the wireless client. After a WiFi client attaches successfully, the LED remains on for 5 minutes, then turns o. UBC1329AA00 Quick Installation Guide BASIC MODEM INFORMATION Example of Cable RF MAC Address 00:71:CC:8E:54:C7 Firmware Version 12.10.9303.15-r193.191.05 Compatibility Local Web User Interface Access DOCSIS 3.1/3.0/2.0/1.0 certied Ethernet 10/100/1000 Mbps Wireless 802.11a/b/g/n/ac/ax MoCA 2.0 http://192.168.100.1 or http://192.168.0.1 Modem Web Page Login (web user interface) Login: admin Password: Randomly generated string, 12 characters in length. Found on the device label. This is your login password. Encryption WPA2-PSK with AES encryption Wireless Default SSID WPA2-PSK Wireless Key WPA2-PSK Wireless Key Example WIFI plus the last 6 characters of the Cable Modem MAC address (in upper case). -5G is added when the 5GHz band is being used. 2.4GHz radio with above MAC address:

SSID = WIFI8E54C7 5GHz radio with above MAC address:

SSID = WIFI8E54C7-5G Randomly generated string, 16 characters in length. Found on the device label. This is your wireless password. HP3WZ7IHXCT6D9QS BATT: Use to connect to an optional external battery. SSID Examples www.ubeeinteractive.com 3 UBC1329AA00 Quick Installation Guide LED BEHAVIOR LED COLOR DESCRIPTION POWER GREEN FLASHES - Power-on failed. Note: LED blinks briey immediately after powering on the device. ON - Internal power-on completed successfully. OFF - No power supplied. DS/US

(downstream/

upstream) GREEN FLASHES - DS and US scans in progress. Also ashes when a rmware upgrade is in progress. ON - Locked to DS and US channels and registered OK, and when data is being passed. ONLINE GREEN ON - Conguration completed successfully, network connected. FLASHES - Obtaining IP address and conguration le. 2.4G GREEN ON - 2.4GHz WiFi is enabled. OFF - Network connect failed. FLASHES - 2.4GHz WiFi trac is being passed. OFF - 2.4GHz WiFi is disabled. FLASHES - 5GHz WiFi trac is being passed. Please note that both the 2.4GHz and 5GHz radios are enabled by default. 5G GREEN ON - 5GHz WiFi is enabled. OFF - 5GHz WiFi is disabled. TEL1 / TEL2 GREEN OFF - Telephony is not provisioned. ON - Telephony is enabled and telephone is on-hook. FLASHES - Call is in progress or eMTA is attempting to register. MoCA GREEN ON - Device is connected to a MoCA network. OFF - Device is not connected to a MoCA network. WPS WHITE When a user pushes the WPS button or triggers WPS via the web user interface, the WPS LED ashes for 4 minutes until the PIN is entered from the wireless client. After a WiFi client attached successfully, the LED remains on for 5 minutes, then turns o. ETHERNET 1-4 (rear panel) GREEN /

ORANGE ON GREEN - An Ethernet device is connected to the UBC1329AA00 at 1000 Mbps speed. ON ORANGE - An Ethernet device is connected to the UBC1329AA00 at 10/100 Mbps speeds. FLASHES (GREEN or ORANGE) - Data is being passed between the UBC1329AA00 and the connected Ethernet device. www.ubeeinteractive.com 4 UBC1329AA00 Quick Installation Guide FCC Caution:

Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 35 cm between the radiator & your body. FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 5GHz Wireless Statement:

For operation within the 5.15~5.25GHz and 5.47~5.725GHz frequency ranges, this device is restricted to indoor environments. This device meets all the other requirements specied in Part 15E, Section 15.407 of the FCC Rules. www.ubeeinteractive.com 5

FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

(Fig. 1) FCC ID: XCNUBC1329

Font: Arial Regular 4pt Model name: UBC1329 Ubee P/N: UBC1329AA00 GUI access URL: http://192.168.100.1 GUI user name: admin GUI password: XXXXXXXXXXXX Wi-Fi Pre-shared Key: XXXXXXXXXXXXXXXX FCC ID: XCNUBC1329 Cable RF MAC Address=XXXXXXXXXXXX SSID: WIFIXXXXXX eMTA MAC Address=XXXXXXXXXXXX SSID: WIFIXXXXXX-5G WAN-MAN MAC Address=XXXXXXXXXXXX S/N=1234567YYYYYY MO: xxxxxxxxxx-VVSS DC: MMDDYY Foxconn P/N: U10C158.00 Factory ID: U Assembled in XXXXX Font: Arial Regular 4pt Font: Arial Regular 4pt Barcode Format: code 128, code B, Height: 3mm FCC ID: XCNUBC1329 Vendor code NOTES:

1. All of the barcode range and SN definition please refer to the test spec 2. SSID: WIFIXXXXXX XXXXXX: the last 3 octets(6 digits) of the RF MAC address using only uppercase alpha-numeric characters with no punctuation. 3 . SSID: WIFIXXXXXX-5G XXXXXX: the last 3 octets(6 digits) of the RF MAC address using only uppercase alpha-numeric characters with no punctuation. 4. Wi-Fi Pre-shared Key: XXXXXXXXXXXXXXXX 16 characters,must be a randomly generated character string,created individually for each unit at time of manufacture (It must use only uppercase alpha-numeric characters,excluding the number "0" and "O", with no punctuation),Other alpha-numeric characters which may be confused, e.g. the number "8" and the letter "B", MAY also be excluded. This will be referred to as the random encryption scheme. 5.GUI access URL: http://192.168.100.1 6.GUI user name admin GUI password: XXXXXXXXXXXX XXXXXXXXXXXX:12 characters,must be a randomly generated character string,created individually for each unit at time of manufacture.(It MUST be restricted to some combination of uppercase alphabetical letters, lowercase alphabetical letters, number characters, and printable special characters. Special characters for GUI password must be limited to: !,#,$,&,%,*. The following characters are not allowed: upper case O(oh),0(zero),lower case l(el),upper case I(eye), upper case Z,upper case S,upper case B.) 7. Assembled in XXXXX (XXXXX:Country of Manufacture, base on the manufacture factory) 8. DC (Date Code), in MMDDYY format: MM

,DD

,YY Foxconn P/N: U10C158.00,U10C158.00 is FOXCONN P/N, 9. 10. MO: xxxxxxxxx is FOXCONN MO Number. Version: VVSS, VV: the engineering version(refer to Foxconn label Rev. column in the cover of the MFG document) SS: the version of A300/A400 product(refer to FDoc Rev. in the cover of MFG document) 50# Mylar(matte)

NOTES:

1.Surface Material color:white 2.Printing color is as color defined in artwork 3.A dhesive:A crylic 4.Adhesive thickness:0.025+/-0.003mm 5.Adhesion to steel(180o

):1.8+/-0.3 kg/25mm 7.Relese Power(90o boll 9.Shipment method: Roll 10.This part must comply with RoHS. 11.Test condition :

1.Soak alcohol(99.7%) at first trial and repeat to soak every 50 times 2.Push force:250g 3.Speed:30 times/min 4.Move back and forth 100 times,printing was not removed

10F-1, No. 5, Taiyuan 1st St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2020-08-03 FCC ID: XCNUBC1329 AUTHORIZATION LETTER To whom it may concern:

We, the undersigned, hereby authorize Andrea Hsia, Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia, Supervisor of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours, yt Ug 220 Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

40F-1, No. 5, Taiyuan 1st St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: August 3, 2020 We, Ubee Interactive Corp. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: XCNUBC1329 If you should have any question(s) regarding this declaration, please dont hesitate to contact us, Thank you!

Name: Steven Chen Ubee Interactive Corp, Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

10F-1, No. 5, Taiyuan 1st St. Jhubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2020-08-03 FCC ID: XCNUBC1329 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

10F-1, No. 5, Taiyuan Ist St. Jhubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2020-08-03 FCC ID: XCNUBC1329 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commissions rules, we request short-term confidential treatment for the following information until 180days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

External photos Test Setup photos Users manual Internal Photos Sincerely yours, Py HY Yo _ nai/ifs Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com