FCC ID: XCNUBC1326 Wireless eMTA

UBC1326AA00 DOCSIS 3.1 Wireless eMTA Quick Installation Guide UBC1326AA00 D3.1 Wireless eMTA Quick Installation Guide Subscriber SAFETY NOTICES Grounding the Device: Install the cable modem to include grounding the coaxial cable to the earth as close as practical to the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with phase-to-phase voltage at 120V. This unit requires a 100-240V, 50/60Hz power adapter. The power adapter must be keyed for proper polarization, and must be fully inserted to contact the back of the power connector port to ensure snug connection. Do NOT use any other power adapter. Disconnecting the Device: If the cable modem becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. Temperature and Altitude: Install the device in a location not to exceed the maximum temperature of 104F (40C). Regular operating altitude is 2000 m, and maximum operating altitude is 4500 m. PREPARING FOR INSTALLATION Locate the RF (coaxial) cable connector on the wall. Verify the power outlet is working and is wired correctly. Place your cable modem within a proper distance from the outlet. INSTALLING THE UBC1326AA00 1. Connect the included leg stands to the bottom of the device to enable the modem to be installed vertically. Connect the coaxial cable (not supplied) to the DS/US (cable) connector on the rear panel of the modem and connect the other end to the cable wall outlet. Do not bend or over tighten the cable, as this may strain the connector and cause damage. To connect a modem and a television to the same wall outlet, you must use a cable line splitter (not included). 2. Connect an Ethernet cable (supplied) to one of the LAN

(Ethernet) ports on the back panel of the modem and connect the other end to the Ethernet port of a computer. Use a Category 5e or Category 6 Ethernet cable with RJ-45 connectors to ensure Gigabit Ethernet speeds (when the computer supports it). 3. Connect an RJ-11 phone cable (not supplied) to the TEL

(telephone) port on the modem (when provisioned for voice service as specied by the service provider), and connect the other end to the phone port of the telephone. If voice service is not provisioned through the service provider, telephone service is not available. 4. Connect the power adapter (supplied) to the PWR (power) port. Connect the other end to a power outlet. UBC1326AA00 Wireless Voice Gateway 2 Connect computers or Ethernet enabled devices (wireless switch or router). A PC should be connected for initial device installation and configuration. RJ-45 4 Device must be installed vertically using the included leg stands to obtain optimum wireless performance. 1 C a b l e / R F RJ-11 3 Analog Phone 1 5. Separate the wall mounting pieces. Mount the top and bottom leg stand pieces (Figure 1) onto the UBC1326AA00 as shown in Figure 2. 6. You can now mount the UBC1326AA00 onto the wall using the screws installed in Step 4. UBC1326AA00 Quick Installation Guide DEVICE WALL MOUNT INSTRUCTIONS You can mount the UBC1326AA00 on a wall by following the steps below:

1. You will need 4 round or pan head screws with the following measurements:

Label A B C D Millimeters

(mm) 7.2 +/- 0.5 2.6 +/- 0.15 19.0 +/- 1.2 3~4 2. Fit the 2 leg stand pieces together with the wall mount template as represented in the graphic to the right. 3. Place this on the wall and use it as a template to mark the wall for the appropriate placement of the screws. 4. Install the 4 screws on the wall

(158 mm or 6.2 inches apart). NOTE: The screws should protrude from the wall so you can t the device between the head of the screws and the wall. If you install the screws in drywall, use hollow wall anchors to ensure the unit does not pull away from the wall due to prolonged strain from the cable and power connectors. Figure 1 Figure 2 2 UBC1326AA00 Quick Installation Guide FEDERAL COMMUNICATION COMMISSION

(FCC) INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. for help. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician 5GHz Wireless Statement:

For operation within the 5.15~5.25GHz and 5.47~5.725GHz frequency ranges, this device is restricted to indoor environments. This device meets all the other requirements specied in Part 15E, Section 15.407 of the FCC Rules. FCC Caution:

Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30 cm between the radiator & your body. NOTE TO CATV INSTALLER This reminder is provided to call the CATV systems installer's attention to section 820-93 of the National Electric Code, which provides guidelines for proper grounding and in particular, specify that the Coaxial cable shield shall be connected to grounding system of the building, as close to the point of cable entry as practical. 3

FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

(Fig. 1) FCC ID: XCNUBC1326

2019/12/03 32.5 R 2 FCC ID: XCNUBC1326 Model Name: UBC1326 Factory ID: U 5

. 9 2 5

. 1 FCC ID: XCNUBC1326 Model Name: UBC1326 Factory ID: U 5

. 6 2 3 38.5

/U10C149.00/00/2 OF 10 PTT label U10C149.00 500.02478.005

10F-1, No. 5, Taiyuan 1st St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel; +886-3-560-0010 Fax: +886-3-560-0017 Date: 2020-08-17 FCC ID: XCNUBC1326 AUTHORIZATION LETTER To whom it may concern:

We, the undersigned, hereby authorize Debby Lin, Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Debby Lin, Supervisor of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours, Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

10F-1, No. 5, Taiyuan 1st St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2020-08-17 FCC ID: XCNUBC1326 Declaration for DFS master devices We, Ubee Interactive hereby declare that the device meets all the other requirements specified in Part 15E Section 15.407. If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

10F-1, No. 5, Taiyuan ist St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tet: +886-3-560-00710 Fax: +886-3-560-0017 Date: 2020-08-17 FCC ID: XCNUBC1326 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Operational Description Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

10F-1, No. 5, Taiyuan Ist St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C, Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: 2020-08-17 FCC ID: XCNUBC1326 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commissions rules, we request short-term confidential treatment for the following information until 180days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

Test Setup photos Sincerely yours, Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com

FCC ID: XCNUBC1326 Description of Permissive Change The application is prepared for FCC class II permissive change by adding frequency band and VHT160 / HE160 modes through software enabling to its original parent application. The adding frequency band is from 5.26 to 5.32GHz and 5.50 to 5.72GHz. Both devices, original and updated versions, are electrically identical in all aspects except enabling 160 MHz mode and frequency bands of 5260 ~ 5320 MHz and 5500 ~

Debby Lin / Senior Specialist Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: 886-3-318 3232 ext. 1900 Fax: 886-3-327 0892 Email: debby.lin@tw.bureauveritas.com Data: 2020-09-04 5720MHz. Regards,

10F-1, No. 5, Taiyuan 1st St. Jnubei Ci, Hsinchu County 302, Taiwan , R.O.C. Tel: +886-3-560-0010 Fax: +886-3-560-0017 Date: November 22, 2019 We, Ubee Interactive Corp. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: XCNUBC1326 If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

[AVIS Name: Steven Chen Ubee Interactive Corp. Tel.: +886-3-560-0010*107 Fax.: +886-3-560-0017 E-mail: steven.chen@ubeeinteractive.com