WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6013359.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case UBC1338AA92 DOCSIS 3.1 Wireless eMTA Safety Manual UBC1338AA92 D3.1 Wireless eMTA Safety Manual Subscriber SAFETY NOTICES Grounding the Device: Install the cable modem to include grounding the coaxial cable to the earth as close as practical to the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with phase-to-phase voltage at 120V. This unit requires a 100-240V, 50/60Hz power adapter. The power adapter must be keyed for proper polarization, and must be fully inserted to contact the back of the power connector port to ensure snug connection. Do NOT use any other power adapter. Disconnecting the Device: If the cable modem becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. Temperature and Altitude: Install the device in a location not to exceed the maximum temperature of 104F (40C). Regular operating altitude is 2000 m, and maximum operating altitude is 4500 m. PREPARING FOR INSTALLATION Locate the RF (coaxial) cable connector on the wall. Verify the power outlet is working and is wired correctly. Place your cable modem within a proper distance from the outlet. INSTALLING THE UBC1338AA92 1. Connect the coaxial cable (not supplied) to the DS/US
(cable) connector on the rear panel of the modem and connect the other end to the cable wall outlet. Do not bend or over tighten the cable, as this may strain the connector and cause damage. To connect a modem and a television to the same wall outlet, you must use a cable line splitter (not supplied). 2. Connect an Ethernet cable (supplied) to one of the LAN
(Ethernet) ports on the back panel of the modem and connect the other end to the Ethernet port of a computer. Use a Category 5e or Category 6 Ethernet cable with RJ-45 connectors to ensure Gigabit Ethernet speeds (when the computer supports it). 3. Connect an RJ-11 phone cable (not supplied) to the TEL
(telephone) port on the modem (when provisioned for voice service as specied by the service provider), and connect the other end to the phone port of the telephone. If voice service is not provisioned through the service provider, telephone service is not available. 4. Connect the power adapter (supplied) to the PWR (power) port. Connect the other end to a power outlet. Note: If using the USB Type C port, maximum is 7.5W (5V/1.5A). 2 UBC1338AA92 Wireless Voice Gateway Connect computers or Ethernet enabled devices (wireless switch or router). A computer should be connected for initial device installation and configuration. Device must be installed vertically using the included leg stands to obtain optimum wireless performance. RJ-45 4 1 C a b l e / R F RJ-11 3 Analog Phone 1 UBC1338AA92 Safety Manual FEDERAL COMMUNICATION COMMISSION
(FCC) INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 5GHz Wireless Statement:
For operation within the 5.15~5.25GHz and 5.47~5.725GHz frequency ranges, this device is restricted to indoor environments. This device meets all the other requirements specied in Part 15E, Section 15.407 of the FCC Rules. FCC Caution:
Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 42 cm between the radiator & your body. NOTE TO CATV INSTALLER This reminder is provided to call the CATV systems installer's attention to section 820-93 of the National Electric Code, which provides guidelines for proper grounding and in particular, specify that the Coaxial cable shield shall be connected to grounding system of the building, as close to the point of cable entry as practical. 2