LED Dimmer Switch Powered by AC Model: UDIM-AC Introduction Thank you for purchasing the Ubiquiti Networks UniFiDimmer Switch. This Quick Start Guide is designed to guide you through installation and includes warranty terms. Package Contents UniFi Dimmer Switch Mounting Screws
(Qty. 2) System Requirements A network switch and wireless access point UniFi LED mobile app software Mobile device: iOS 10 or Android 5.0 UniFi LED Controller software:
Computer: UniFi Application Server 0.5.0, Ubuntu 16.04 LTS (Xenial Xerus) 64-bit, or Debian 9 64-bit Web browser: Google Chrome (Other browsers may have limited functionality.) TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. It is the professional installers responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. Installation Requirements Phillips screwdriver Wire stripper/cutter Needle-nose pliers (Optional) IMPORTANT: The UDIM-AC is to be installed by a qualified electrician in accordance with local electrical codes and regulations. IMPORTANT : Le UDIM-AC doit tre install par un lectricien qualifi conformment aux codes lectriques locaux et des rglements. WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off power at the circuit breaker or fuse before installing. AVERTISSEMENT : POUR VITER TOUT RISQUE D'INCENDIE, D'LECTROCUTION OU DE DCS;
coupez le courant au niveau du disjoncteur ou du coupe-circuit ou fusible avant l'installation. Network Topology Requirements The UniFi Dimmer Switch is designed for use with the UniFi LED Panel (models ULED-AT and ULED-AC), and is one of three ways to control the UniFi LED Panel:
UniFi Dimmer Switch A user in the immediate vicinity controls the UniFi LED Panel using the UniFi Dimmer Switch. UniFi LED App over Layer 2 Network A local user runs the app to connect to a UniFi AP on the same Layer 2 network as the UniFi LED Panel. UniFi LED Controller over Layer 2 Network Alocal user runs the LED Controller software on the same Layer 2 network as the UniFi LED Panel. Network topology requirements are as follows:
DHCP-enabled network (for the UniFi LED Panel and Dimmer Switch to obtain an IP address) For UniFi Dimmer Switch only:
A UniFi Dimmer Switch connected to a UniFi AP on the same Layer 2 network as the UniFi LED Panel For LED Controller software:
A UniFi Application Server running the UniFi LED Controller software and connected to the same Layer 2 network as the UniFi LED Panel For LED app only:
A UniFi AP connected to the same Layer2 network as the UniFi LED Panel UAP-AC-PRO UniFi LED App 100-277VAC 100-240VAC ULED-AC UDIM-AC ULED-AT UniFi PoE Switch UniFi LED Controller UniFi Application Server LAN WAN USG-XG-8
(DHCP Server) Internet Sample Network Diagram Hardware Overview Front LED Status LED LED Color Status Flashing White Initializing. Breathing White System ready. Alternating White/Blue Firmware upgrade is taking place. Breathing Blue Adopted by the UniFi LED Controller. Flashing Blue This is used to locate a UniFi Dimmer Switch. When you click Locate in the UniFi LED Controller or UniFi LED app, the UniFi Dimmer Switch LED will flash. Back Port Earth Ground Neutral Live N L AC power connections:
Earth ground (green/yellow), N Neutral (white), and LLive (red). Bottom Button Reset Button Front Plate Back Plate Reset The Reset button serves two functions:
Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. Hardware Installation 1. Detach the Front Plate of the UniFi Dimmer Switch from the Back Plate. 2. Connect the Earth Ground (green/yellow), Neutral (white), andLive (red) wires to the power cables in the wall box. 3. Orient the Back Plate so that the word UP appears in the upper-right corner. Then attach the Back Plate to the wall box using the Mounting Screws. WARNING: To avoid damage to the UniFi Dimmer Switch:
Use ONLY the included Mounting Screws or replacement screws that meet this specification:
#6-32x26 truss head machine screw
(maximum head diameter: 8 mm) Do NOT over-tighten the Mounting Screws. 4. Re-attach the Front Plate of the UniFi Dimmer Switch to the Back Plate. The UniFi Dimmer Switch is Plug and Play; by default, it will be paired automatically with all UniFi LED Panels on the same Layer2 network. To pair the UniFi Dimmer Switch with specific LED Panels, go to the Pairing with Specific LED Panels section. Note: For best results, we recommend the following:
Create dedicated VLANs for lighting and assign all UniFi LED Panels and Dimmer Switches to these VLANs Configure each VLAN using a 25-bit subnet mask; for example, 192.168.2.1/25 Pair each Dimmer Switch with no more than 128 LED Panels. Pairing with Specific LED Panels Follow the instructions for the software you wish to use:
UniFi LED App 1. Install the UniFi LED app on your smartphone or mobile device. The app is available from the App Store or GooglePlay Store. 2. Launch the app. 3. Follow the on-screen instructions to pair the UniFiDimmer Switch with the desired UniFi LED Panels. UniFi LED Controller Software 1. Install the latest version of the UniFi LED Controller software on a computer on the same Layer 2 network as the UniFi LED Panel:
Ubuntu users Download the software from:
https://github.com/ubiquiti/eot-controller UAS users Install the software using the UniFi Application Server (UAS) management console. 2. Launch a web browser and go to: http://localhost:20080 3. The UniFi LED Controller will appear, allowing you to pair the UniFiDimmer Switch with the desired UniFi LED Panels and customize other settings. For additional details on the UniFi LED Controller, refer to the User Guide available at:
www.ubnt.com/download/unifi Using the Touch Pad Once the UniFi Dimmer Switch is paired with the UniFi LED Panel, you can use the UniFi Dimmer Switchs Touch Pad to turn the LED Panel on and off and to control its brightness:
To toggle the LED Panel on or off, tap the Touch Pad once. To change the LED Panels brightness, press the Touch Pad and slide your finger up or down. Where you release your finger determines how much brighter or dimmer the LED Panel becomes:
Swiping to the top of the Touch Pad sets the brightness to its maximum level (brightest). Swiping to the bottom of the Touch Pad sets the brightness to its minimum level (dimmest). Brightest Dimmest Touch Pad Specifications Dimensions Weight Management Interface Networking Interface Max. Power Consumption Power Method Supported Voltage Range Max. Power Consumption Buttons Bluetooth Wireless Security Operating Temperature Operating Humidity Certifications UDIM-AC 71 x 115 x 37.5 mm
(2.80 x 4.53 x 1.48") 125 g (4.41 oz) UniFi LED Controller UniFi LED App 802.11b/g/n 2.4 GHz 5W AC Input 100-240VAC 5W Reset v4.1 WEP, WPA/WPA2 Personal 0 to 40 C (32 to 104 F) 10 to 90% Noncondensing CE, FCC, IC Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: The UDIM-AC is to be installed by a qualified electrician in accordance with local electrical codes and regulations. AVERTISSEMENT : Le UDIM-AC doit tre install par un lectricien qualifi conformment aux codes lectriques locaux et des rglements. WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off power at the circuit breaker or fuse before installing. AVERTISSEMENT : POUR VITER TOUT RISQUE DINCENDIE, DLECTROCUTION OU DE DCS; coupez le courant au niveau du disjoncteur ou du coupe-circuit ou fusible avant linstallation. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. Limited Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that the product(s) furnished hereunder (the Product(s)) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks authorized representatives, or as approved by Ubiquiti Networks in writing;
has been painted, rebranded or physically modified in any way;
has been damaged due to errors or defects in cabling;
(II)
(III)
(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;
has been damaged or impaired as a result of using third party firmware;
(V)
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products (including the Products) for buyers application and/
or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitter FCC ID: SWX-UDIMAC has been approved by FCC. ISED Canada CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-UDIMAC) has been approved by ISED Canada. CAN ICES-3(A)/NMB-3(A) Le prsent appareil est conforme aux CNR dISDE Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. 2. lappareil ne doit pas produire de brouillage;
lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Le prsent metteur radio (IC : 6545A-UDIMAC) a t approuv par ISDE Canada. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une distance de sparation de toute personnes dau moins 20cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur. Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Note: This device meets Max. TX power limit per ETSI regulations. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity
[Bulgarian] UBIQUITI NETWORKS , UDIM-AC 2014/53/.
:
www.ubnt.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa UDIM-AC u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: www.ubnt.com/compliance etina [Czech] Tmto UBIQUITI NETWORKS prohlauje, e typ rdiovho zazen UDIM-AC je v souladu se smrnic 2014/53/EU. pln znn EU prohlen o shod je k dispozici na tto internetov adrese: www.ubnt.com/compliance Dansk [Danish] Hermed erklrer UBIQUITI NETWORKS, at radioudstyrstypen UDIM-AC er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklringens fulde tekst kan findes p flgende internetadresse: www.ubnt.com/compliance Nederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur UDIM-AC conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:
www.ubnt.com/compliance English Hereby, UBIQUITI NETWORKS declares that the radio equipment type UDIM-AC is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/compliance Eesti keel [Estonian] Kesolevaga deklareerib UBIQUITI NETWORKS, et kesolev raadioseadme tp UDIM-AC vastab direktiivi 2014/53/EL nuetele. ELi vastavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil: www.ubnt.com/compliance Suomi [Finnish] UBIQUITI NETWORKS vakuuttaa, ett radiolaitetyyppi UDIM-AC on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen tysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/compliance Franais [French] Le soussign, UBIQUITI NETWORKS, dclare que lquipement radiolectrique du type UDIM-AC est conforme la directive 2014/53/UE. Le texte complet de la dclaration UE de conformit est disponible ladresse internet suivante: www.ubnt.com/compliance Deutsch [German] Hiermit erklrt UBIQUITI NETWORKS, dass der Funkanlagentyp UDIM-AC der Richtlinie 2014/53/EU entspricht. Der vollstndige Text der EU-Konformittserklrung ist unter der folgenden Internetadresse verfgbar: www.ubnt.com/compliance
[Greek] / UBIQUITI NETWORKS, UDIM-AC 2014/53/.
: www.ubnt.com/compliance Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a UDIM-AC tpus rdiberendezs megfelel a 2014/53/EU irnyelvnek. Az EU-megfelelsgi nyilatkozat teljes szvege elrhet a kvetkez internetes cmen: www.ubnt.com/compliance slenska [Icelandic] Hr me lsir UBIQUITI NETWORKS yfir v a UDIM-AC er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 2014/53/EU. Fullur texti ESB samrmisyfirlsing er a finna eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio UDIM-AC conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latvieu valoda [Latvian] Ar o UBIQUITI NETWORKS deklar, ka radioiekrta UDIM-AC atbilst Direktvai 2014/53/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams d interneta vietn:
www.ubnt.com/compliance Lietuvi kalba [Lithuanian] A, UBIQUITI NETWORKS, patvirtinu, kad radijo rengini tipas UDIM-AC atitinka Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas iuo interneto adresu: www.ubnt.com/compliance Malti [Maltese] Bdan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta tagmir tar-radju UDIM-AC huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformit tista tii kkonsultata minn www.ubnt.com/compliance Norsk [Norwegian] UBIQUITI NETWORKS erklrer herved at utstyret UDIM-AC er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklringen er tilgjengelig p flgende internettadresse:
www.ubnt.com/compliance Polski [Polish] UBIQUITI NETWORKS niniejszym owiadcza, e typ urzdzenia radiowego UDIM-AC jest zgodny z dyrektyw 2014/53/UE. Peny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym: www.ubnt.com/compliance Portugus [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rdio UDIM-AC est em conformidade com a Diretiva 2014/53/UE. O texto integral da declarao de conformidade est disponvel no seguinte endereo de Internet:
www.ubnt.com/compliance Romn [Romanian] Prin prezenta, UBIQUITI NETWORKS declar c tipul de echipamente radio UDIM-AC este n conformitate cu Directiva 2014/53/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet: www.ubnt.com/compliance Slovenina [Slovak] UBIQUITI NETWORKS tmto vyhlasuje, e rdiov zariadenie typu UDIM-AC je v slade so smernicou 2014/53/E. pln E vyhlsenie o zhode je k dispozcii na tejto internetovej adrese: www.ubnt.com/compliance Slovenina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme UDIM-AC skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/compliance Espaol [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioelctrico UDIM-AC es conforme con la Directiva 2014/53/UE. El texto completo de la declaracin UE de conformidad est disponible en la direccin Internet siguiente:
www.ubnt.com/compliance Svenska [Swedish] Hrmed frskrar UBIQUITI NETWORKS att denna typ av radioutrustning UDIM-AC verensstmmer med direktiv 2014/53/EU. Den fullstndiga texten till EU-frskran om verensstmmelse finns p fljande webbadress: www.ubnt.com/compliance Online Resources Support help.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA w w w . u b n t . c o m 2017-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Android, Google, Google Play, the Google Play logo and other marks are trademarks of Google Inc. All other trademarks are the property of their respective owners. AI062618