FCC ID: SWX-USPS UniFi Network Power Strip

USP-StripDatasheet Datasheet USP-Strip UniFi SmartPower 6-Port Power Strip The UniFi SmartPower Strip is a Wi-Fi connecter power strip installed between an AC outlet and the power plugs of your internet connectivity hardware (modems, router, etc). The UniFi Network Controller continuously monitors availability of an internet connection. If the connection drops, the UniFi SmartPower Plug automatically restarts the connected devices by disconnecting power for a short period of time*. The UniFi SmartPower Strip offers six power control outlets for 125VAC devices (up to 1250W total). Four USB Type A ports can charge smartphones, reading lights, and other devices (up to 1A per port).

* Req u ires U n iFi D ream Mac h in e Dimensions 229.5 x 111.5 x 37.8 mm (9 x 4.4 x 1.5") Weight 845 g (1.86 lb) Enclosure Characteristics Fire Retardant Plastic, SABIC Lexan 945 Polycarbonate Mechanical Hardware Processor Specs ESP8266, 32-bit Tensilica LX106 Core, 160 MHz Memory Information 4 MB Flash Management Interface 2.4 GHz Wi-Fi Networking Interface 802.11 b/g/n Wi-Fi Buttons

(1) Multifunction Button LEDs

(1) Power, Blue/White Flashing White: Bootup in Progress Flashing Blue: Firmware Upgrading Steady White: Factory Defaults, Awaiting Adoption Steady Blue: Device is Adopted Max. Power Consumption 1250W for 125VAC Power Method AC Input Power Supply AC/DC Embedded Supported Power Voltage AC Input/Output: 125v~10A Max, 60 Hz Operating Frequency 2.4 GHz Antennas Single-Band Antenna MIMO 1x1, 2x1 ESD/EMP Protection Air/Contact: 24 kV Operating Temperature 0to 40 C (32to 104 F) Operating Humidity 10 - 90% Noncondensing Certications FCC, IC Software Wi-Fi Standards 802.11 b/g/n Power Save Yes Wireless Security WPA2-PSK AES/TKIP Supported Data Rates (Mbps) 802.11b 1, 2, 5.5, 11 Mbps 802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11n 6.5 -72.2 Mbps (MCS0 - MCS7, HT 20) Specications are subject to change. Ubiquiti products are sold with a limited warranty described at: www.ui.com/support/warranty 2020 Ubiquiti Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, UniFi, and UniFi Network are trademarks or registered trademarks of Ubiquiti Inc. in the United States and in other countries. All other trademarks are the property of their respective owners. FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. The following apply to Class B products This equipment has been tested and found to comply with the limits for a Class B digital device. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. ISED Canada CAN ICES-3(B)/NMB-3(B) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-3(B)/NMB-3(B) Le prsent appareil est conforme aux CNR dISDE Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. lappareil ne doit pas produire de brouillage;

2. lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in con junction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une dis tance de sparation de toute personnes daumoins 20 cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur.

UNF i comm MIN: USP-Strip FCCID: SWX-USPS

(CN Power Strip Input/Output: 125-108 Max,60Hz |C:6545A-USPS ig FP Usicitine 685 Third Avenue tuimon New York, NY 10017 USA

Ubiquiti Inc. Date: 2022/01/07 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Requesting Class II permissive change To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: SWX-USPS This report is prepared for FCC Class II permissive change. RF WiFi 2.4G module and its antenna are not any changed. The major change filed under this application is:

Change #1: Change PCB board version (remain same RF chip and circuit) Original Grant Issue Date is on 2020/08/02 Best Regards Mark Feil/ Compliance Manager Address: 685 Third Avenue, New York, 10017, United States Company Name: Ubiquiti Inc. Tel: +1 408-942-3084 Fax: +1 408-904-5255 Email: compliance@ubnt.com

Ubiquiti Inc. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: SWX-USPS Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

File Name Exhibit Type USP-Strip_ Block Diagrams Block Diagrams USP-Strip_ Operational Description Operational Description USP-Strip_ Schematic Diagrams Schematic Diagrams The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type External Photos, Internal Photos Test Setup Photos Users Manual Planned Release Date STC: 180 days from the date of grant. (notes 2, 3, 4, 5). If no date is given, 45 days from grant date will be used. Sincerely, Mark Feil Rev 11/20/07 File Name USP-Strip_ External Photos USP-Strip_ Internal Photos USP-Strip_ Test Setup Photos USP-Strip_ Users Manual

Ubiquiti Inc. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date:

SUBJECT: FCC Application for SWX-USPS To Whom It May Concern:

We, the undersigned, hereby authorize Nina Hsu at Cerpass Technology Inc. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Cerpass Technology Inc. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Mark Feil Compliance Manager Ubiquiti Inc. C:\Users\Jerry\Downloads\Strip\POA_Letter_SWX-USPS.docx

FCC, Request for non-disclosure RF_501, Issue 5 Date: 10-Aug-09 Page 1 of 1 Company Name: Ubiquiti Inc. Address:

City:

Country:

685 Third Avenue New York, NY, 10017 United States Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands To: Telefication B.V., Dept. FCC TCB Subject: Request for confidentiality FCC ID: SWX-USPS Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos Users Manual Test Set-up Photos External Photos Justification: For marketing purpose Planned Release Date STC: 180 days from the date of grant. (notes 2, 3, 4, 5) Name and signature of applicant: Mark Feil Date: 2020/06/20 Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_160, Issue 02 Ubiquiti Inc. 685 Third Avenue New York, NY United States, 10017 We Name:

Address:

City:

Country:

Declare that:

Name Representative of agent: Delia Feng (1) Agent Company name: Cerpass Technology Corporation Address: No.10, Lane 2, Lianfu Street, Luzhu Dist., City: Taoyuan City 33848 Country: Taiwan, R.O.C. is authorized to apply for Certification of the following product(s):

Product description: UniFi Network Power Strip Type designation: USP-Strip Trademark:

UBIQUITI on our behalf. Date:

City:

Name:

Function:

Compliance Manager June 20, 2020 New York Mark Feil Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.