User Manual 1. Introduction and Feature ................................................................................................................ 2 2. User Mode (WiFi) ............................................................................................................................. 3 3. cTX/RX (EDR-BT2.0)...................................................................................................................... 6 4. Antenna Trace Design ...................................................................................................................... 8 5. Regulatory ...................................................................................................................................... 11 1. Introduction and Feature 1. Introduction WP1-2020-A1 is 2x2 802.11a/b/g/n/ac dual-band Wi-Fi + BT 5.1 Module. The Wi-Fi subsystem contains 802.11a/b/g/n/ac MAC /Baseband /Radio. The Bluetooth subsystem contains Baseband/Radio/Link controller. The module is a small size module based on metal lid shielding package that provides full function of 802.11a/b/g/n/ac and Bluetooth 5.1 in a tiny module via 75 pins LGA footprint. 2. Feature 1) Full IEEE 802.11a/b/g/n/ac compatibility with enhanced performance. 2) Support dual-band 2T2R mode. 20/40M bandwidth in 2.4G band and 20/40/80M bandwidth in 5G band. IEEE 802.11 d/e/h/i/j/k/r/v/w support. 3) Support BT5.1 with BLE2M, BLE long range and compatible BT4.2. Support 7 simultaneous active ACL connection and 16 BLE links. 4) Frequency Band 2.4 to 2.5GHz 4.9 to 5.845GHz 5) Operating Temperature
-10C to 65C 6) Relative Humidity range Less than 60% for Storage Less than 85% for Operation 2. User Mode (WiFi) 1. Boot up PC or NB with the flash installed Linux OS. 2. 5V for EUT from the power supply. 3. Type sudo su on Terminal in Linux to get root authority. EUT could be controlled if mmc0:
new high speed SDIO card at address 0001 is shown after typing dmesg. 4. Type cd /usr and then insmod wlan_mt7663_sdio.ko to enable WiFi function of EUT. 5. Link to AP with another PC or NB through Ethernet cable, open DHCP function in it and record the IP address. 6. Click WiFi icon on upper-right corner on Linux and disable WiFi. 7. After disabling WiFi, then enable Wi-Fi, and Wi-Fi Networks (Intel.) and Wi-Fi Networks
(MediaTek) would be visible. The Wi-Fi Networks (MediaTek) is device name of EUT. 8. Select the SSID you would link to by Wi-Fi Networks (MediaTek). 9. Click Connection Information, check the IP address and record it. 10. Copy iperf tools for Linux on Linux Desktop and then use the command below to copy the tools in usr file. cp /home/ubuntu/Desktop//iperf /usr/
11. Use the command below to install the tools in cd /usr path. 13. Enable the function for possible applition as below on the 2 PCs or NBs. apt install iperf 12. Enter the command below. chmod 777 iperf iperf client side iperf -c IP -t 10000 -i 1 iperf server side iperf -s -i 1 ping IP 14. Ping function is also usable and ctrl+c could stop the ping function. 3. cTX/RX (EDR-BT2.0) 1. Boot up PC or NB with the flash installed Linux OS. 2. 5V for EUT from the power supply. 3. Type sudo su on Terminal in Linux to get root authority. EUT could be controlled if mmc0:
new high speed SDIO card at address 0001 is shown after typing dmesg. 4. Copy btmtksdio_user.ko file onto Linux Desktop and use the below command to copy btmtksdio_user.ko in the usr file. cp /home/ubuntu/Desktop/btmtksdio_user.ko /usr/
5. Search BT device by the below command. modprobe hci_uart insmod btmtksdio_user.ko 6. Pair EUT to the BT device to be linked as shown below. 7. After pairing, check the MAC address of the BT device in Bluetooth Settings. 8. Use the command hciconfig to check the hci number of EUT. For each number shown Bus:
SDIO, it would be the one of EUT. 9. Replace MAC (such as B8:D5:0B:2E:30:48) and hci number (such as hci1) with the actual ones in the below command and the ping function with BT link would be enabled. while [ -z `pidof l2ping` ]; do sudo l2ping -i hci1 B8:D5:0B:2E:30:48; sleep 3; done 4. Antenna Trace Design WLAN WiFi chain0/chain1 Top layer Trace length WiFi chain0 (956.66mils) WiFi chain1 (871.31mils) WLAN BT Top layer BT_ANT (1425.34mils) RF traces width : 17.5 mils, spacing 35 mils PCB Stack-up for reference PCB stack (1-2-1) as below:
Layer Thickness (mil) Solder Mask L1 P.P. L2 Core L3 P.P. L4 Total Solder mask 25um 28.44 0.7 1.6 10 1.4 1.4 10 1.6 0.7 55.84 DK 4.1 4.19 4.21 4.19 4.1 Total Thickness: 55.1mils +/- 10% (1400 um +/- 10%)
*Note : The thickness of Solder Mask on top side is necessary to be controlled within The Land Pattern and Dimensions should be compliance with USI's Standard PCB Design. The characteristics of products may vary depending on the pattern drawing method, grounding method, land dimensions, land forming method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the characteristics in the actual set. When using non-standard lands, contact Universal Global Scientific Industrial Co., Ltd. Beforehand. USI uses various test mode programs for test set up which operate separate from production firmware. Host integrators should contact USI for assistance with test modes needed for module/host compliance test requirements. The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. US 5. Regulatory This module is intended for OEM integrators under the following conditions:
1. Ensure that the end-user has no manual instructions to remove or install module. 2. This module is certified pursuant to Part 15 rules section 15.247, 15.407 and RSS-247. 3. This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Frequency Band Antenna Type Model Number Gain(dBi) 2400-2483.5MHz; BT 5150-5850MHz Dipole RFA25C53B32C255V2 3.5 5 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. and This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, 2) The transmitter module may not be co-located with any other transmitter or antenna. While the 2 conditions above are met, further transmitting tests wont be required. However, the OEM integrator shall still meet those additional compliance tests for the end products with the module installed. This module has been approved under stand-alone configuration. OEM integrator has to limit the operation channels in channel 1-11 for 2.4GHz band. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: COF-WMBACMT63. The grantee's FCC ID can be used only when all FCC compliance requirements are met. The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this The end user manual shall include all required regulatory information/warning as show in this This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed with 20 cm is maintained between the antenna and users in mobile or fixed applications. 2) The Antenna for Module (COF-WMBACMT63) is detachable and the maximum antenna gain allowed for use with this device is 3.5 dBi@2.4GHz band & 5dBi@5GHz band. 3) The transmitter module may not be co-located with any other transmitter or antenna. 4) OEM integrators Must demonstrate SAR tests and meet compliance before end-product with module (COF-WMBACMT63) marketed in portable application. While the 2 conditions above are met, further transmitting tests wont be required. However, the OEM integrator shall still meet those additional compliance tests for the end products with the module installed. OEM integrators Must demonstrate Part 15B test and meet compliance before end-product with module (COF-WMBACMT63) marketed. module. manual. Canada This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme aux RSS RSS de ISED. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvant entraner un fonctionnement non This device and its antenna(s) must not be co-located or operating in conjunction with any other Cet appareil et son (ses) antenne (s) ne doivent pas tre co-localiss ou utiliss conjointement avec souhait. antenna or transmitter. une autre antenne ou un autre metteur. Radiation Exposure Statement:
between the radiator & your body. Dclaration d'exposition aux radiations:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm Cet quipement est conforme aux limites d'exposition au rayonnement ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. While the 2 conditions above are met, further transmitting tests wont be required. However, the OEM integrator shall still meet those additional compliance tests for the end products with the module installed. Cet appareil est destin uniquement aux intgrateurs OEM dans les conditions suivantes: (Pour une utilisation avec un appareil de module) 1) Lantenne doit tre installe de manire ce quil reste 20 cm entre lantenne et les utilisateurs, et 2) Le module metteur ne peut pas tre co-localis avec un autre metteur ou une antenne. Bien que les 2 conditions ci-dessus soient remplies, des tests de transmission supplmentaires ne seront pas ncessaires. Toutefois, l'intgrateur OEM doit toujours satisfaire ces tests de conformit supplmentaires pour les produits finaux avec le module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Si ces conditions ne peuvent pas tre remplies (par exemple, certaines configurations d'ordinateurs portables ou la co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considre comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera responsable de la rvaluation du produit final (y compris de l'metteur) et de l'obtention d'une autorisation distincte du Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:10293A-WMBACMT63. tiquetage du produit final Ce module metteur est uniquement autoris tre utilis dans un appareil o lantenne peut tre installe de manire ce que 20 cm puissent tre maintenus entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans une zone visible avec les informations suivantes: Contient le module d'mission IC: 10293A-WMBACMT63. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this The end user manual shall include all required regulatory information/warning as show in this module. manual. Informations manuelles l'utilisateur final Lintgrateur OEM doit tre conscient de ne pas fournir lutilisateur final des informations concernant la procdure dinstallation ou de suppression de ce module RF dans le manuel de lutilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations / avertissements rglementaires requis, comme indiqu dans ce manuel. This radio transmitter [IC: 10293A-WMBACMT63] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Frequency Band Antenna Type Model Number Gain(dBi) 2400-2483.5MHz; BT 5150-5850MHz Dipole RFA25C53B32C255V2 3.5 5 Le prsent metteur radio [IC: 10293A-WMBACMT63] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Frequency Band Antenna Type Model Number Gain(dBi) 2400-2483.5MHz; BT 5150-5850MHz Dipole RFA25C53B32C255V2 3.5 5 The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Japan R XXX-XXXXXX T D XX XXXX XXX W52/W53