XR2 Xfinity Remote 1 Meet Your Remote 2 Turn On Your Remote TV Power All Power TV Input Changes to the next available input on your TV
(if programmed in Step 4) Search Discover content by channel, program or key words. Install batteries in the remote and turn on your devices. A To set up your remote, first install AA batteries
(sold separately). The All Power key will blink green four times as the remote powers up
(about 5 seconds). Start XFINITY / Menu Access Guide, Saved, XFINITY On Demand, Apps, Search and Settings. Back B Turn on your TV. C Turn on your cable box. Setup Program remote for Aim Anywhere or to control your TV or audio device. Number Keys Swap Switches between two DVR tuners so you can control playback of two channels. 3 Program Your Remote To Control Your Set-Top Box Your remote is preprogrammed to operate XFINITY cable boxes. If you are using the remote for control of a non-XFINITY cable box, you may need to program the remote for the Motorola or Cisco mode. Follow the steps below to program your remote. A B C Press the Setup button until the All Power key on the remote changes from red to green. Press B for control of a Motorola brand cable box; press C for control of a Cisco or Scientific-Atlanta brand cable box. Note: If you need to re-program the remote for control of an XFINITY cable box, repeat the steps above and press A in step 2. Press the XFINITY key to check that your remote controls your set-top box. If it does, youre all set. If not, repeat these steps but press C for Cisco mode or A for XFINITY mode in step B. Once the code is correctly entered, your XFINITY Remote is paired with the device. 4 Pair Remote for Aim Anywhere Control 5 Control Your TVs Power and Volume Control your cable box without having to point at it, even when it is inside a cabinet or entertainment center. Aim Anywhere is only supported on certain XFINITY cable boxes. To see if your cable box supports Aim Anywhere control visit xfinity.com/remotes A Press the Setup button until the All Power key on the remote changes from red to green. B Press the XFINITY button. C Follow the on-screen instruction to enter the 3-digit code that appears. Once the code is correctly entered, your XFINITY Remote is paired with the device.
?
?
Not working? Make sure to install batteries in the remote, check that your TV is on and that you are entering the correct 3-digit code on your TV screen. Need to remove Aim Anywhere control? Press and hold the Setup button on the remote until the status LED changes from red to green. Press A on the remote. If the status LED blinks green twice, you have successfully removed Aim Anywhere. A B Using the list on the right, find the first 5-digit code for your TV manufacturer. Press and hold the Setup button (about 3 seconds) until the Status LED changes from red to green. C Enter in the first 5-digit code for you TV manufacturer. The Status LED should blink green twice. D Verify that the code was accepted by using your remote to adjust volume and turn the TV on and off. Popular TV Manufacturer Codes Emerson Insignia JVC LG Magnavox Panasonic Philips RCA Samsung Sanyo Sharp Sony Toshiba VIZIO 11864, 10171 12049, 11641 11774, 12321 12731, 10178 10054,12597 11480, 10051 11867, 12597 10047, 11447 12051, 10702 10154, 11142 10093, 12360 10810, 11685 10156, 11524 11758, 12707 11712, 13579 Westinghouse If your code isnt listed or you would like to control an audio device, visit xfinity.com/remotes Not working? Try the second code listed. Still not working? Visit xfinity.com/remotes for a complete list of codes or use the My Account app for mobile (iOS/Android) or X1. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase or decrease the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that which the receiver is connected. Consult the dealer or an experienced remote control/ TV technician for help. It is strongly recommended that the TV be plugged into a separate wall outlet. The user is cautioned that changes and modifications made to this equipment without the approval of the manufacturer could void the users authority to operate this equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. XR2 Xfinity Control Remoto 1 Conozca su control remoto 2 Encienda el control remoto 3 Programe el control remoto para manejar su conversor 4 Configure el control para el modo apuntar a cualquier lado 5 Encienda y apague la TV y maneje su volumen Cdigos de fabricantes populares Encender/
apagar la TV Inicio XFINITY / Men Acceda a Gua, Guardado, XFINITY a pedido, Aplicaciones, Buscar y Configuraciones. Configurar Programe el control en el modo apuntar desde cualquier lado o para controlar su TV o dispositivo de audio. Encendido general Entrada de TV Cambia a la prxima entrada disponible en su TV (si se programa en el paso 4) Buscar Descubra el contenido por canal, programa o palabras clave. Teclas numricas Cambiar Cambia entre dos DVR para poder controlar la reproduccin de dos canales. Instale las pilas en el control remoto y encienda los dispositivos. El control remoto est programado en fbrica para funcionar con los conversores XFINITY. Si utiliza el control para manejar un conversor que no es XFINITY, es posible que deba programarlo para el modo Motorola o Cisco. Siga los pasos siguientes para programar su control. Maneje el conversor sin tener que apuntar el control hacia l, incluso cuando se encuentra dentro de un mueble. El modo apuntar a cualquier lado solo puede utilizarse en ciertos conversores XFINITY. Para ver si su conversor puede utilizarse con el modo apuntar a cualquier lado visite xfinity.com/remotes. A Para configurar su control remoto, primero instale las pilas AA (se venden por separado). La tecla All Power destellar en color verde cuatro veces mientras el control remoto se enciende (unos 5 segundos). Parte posterior B Encienda la TV. C Encienda el conversor. A B C Presione el botn Setup hasta que la tecla All Power cambie de rojo a verde. Presione B para controlar un conversor Motorola o C para controlar un conversor Cisco o Scientific-Atlanta. Nota: Si debe reprogramar el control remoto para manejar un conversor XFINITY, repita los pasos anteriores y presione A en el paso 2. Presione la tecla XFINITY para verificar que el control maneja su contrario. Si lo hace, todo est listo. De lo contrario, repita estos pasos, pero presione C para el modo Cisco o A para el modo XFINITY en el paso B. Una vez que el cdigo haya sido ingresado correctamente, el control remoto XFINITY est conectado con el dispositivo. A Presione el botn Setup hasta que la tecla All Power cambie de rojo a verde. B Presione el botn XFINITY. C Siga las instrucciones en la pantalla para ingresar el cdigo de 3 dgitos. Una vez ingresado el cdigo correctamente, el control remoto XFINITY est conectado con el dispositivo.
?
?
No funciona? Asegrese de haber instalado las pilas en el control remoto, que la TV est encendida y que ha ingresado correctamente el cdigo de 3 dgitos que aparece en la pantalla del televisor. Necesita quitar el modo apuntar a cualquier lado? Presione y sostenga el botn Setup en el control remoto hasta que la luz de estado cambie de rojo a verde. Presione A en el control. Si la luz de estado destella dos veces en color verde, se quit el modo apuntar a cualquier lado. A B C Busque en la lista de la derecha el primer cdigo de 5 dgitos que corresponda al fabricante de su TV. Presione y sostenga el botn Setup (unos 3 segundos) hasta que la luz de estado cambie de rojo a verde. Ingrese primero el cdigo de 5 dgitos correspondiente al fabricante de su TV. La luz de estado debe destellar dos veces en color verde. D Verifique que el cdigo fue aceptado usando el control para regular el volumen y para encender y apagar la TV. Emerson Insignia JVC LG Magnavox Panasonic Philips RCA Samsung Sanyo Sharp Sony Toshiba VIZIO Westinghouse 11864, 10171 12049, 11641 11774, 12321 12731, 10178 10054,12597 11480, 10051 11867, 12597 10047, 11447 12051, 10702 10154, 11142 10093, 12360 10810, 11685 10156, 11524 11758, 12707 11712, 13579 Si su cdigo no est en la lista o le gustara controlar un equipo de audio, visite xfinity.com/remotes No funciona? Repita estos pasos con el segundo cdigo que aparece en la lista de la derecha. Sigue sin funcionar? Visite xfinity.com/remotes para consultar una lista completa de cdigos de fabricantes. Declaracin de conformidad de la FCC Este equipo se ha examinado y se ha comprobado que cumple con los lmites establecidos para un equipo digital de clase B, conforme a la parte 15 de las reglas de la FCC. Estos lmites se disearon para proporcionar una proteccin razonable contra interferencias perjudiciales en una instalacin residencial. Este equipo genera, usa y puede emitir energa de radiofrecuencia y, si no se usa de acuerdo con las instrucciones, puede causar interferencias perjudiciales a las comunicaciones de radio. No hay ninguna garanta de que no ocurrirn interferencias en una instalacin en particular. Si este equipo causa interferencias perjudiciales a la recepcin de la radio o la televisin, se aconseja al usuario a que intente corregir las interferencias de una o ms de las formas ofrecidas a continuacin:
Reoriente o reubique la antena receptora. Aumente o disminuya la separacin entre el equipo y el recibidor. Conecte el equipo a una conexin de un circuito diferente al que est conectado el recibidor. Pida ayuda a un distribuidor o a un tcnico de TV y controles remotos experimentado. Es sumamente recomendable que la TV est enchufada a una conexin de la pared diferente. Se advierte a los usuarios que los cambios y modificaciones que se hagan al equipo sin la aprobacin del fabricante podran invalidar la autoridad del usuario para manejar este equipo. Este equipo se ajusta a la parte 15 de las reglas de la FCC. El funcionamiento est sujeto a las dos condiciones siguientes: (1) Este equipo no puede causar interferencias perjudiciales y (2) este equipo debe aceptar cualquier interferencia recibida, incluso la que pueda causar un funcionamiento indeseado.