FCC ID: MG3-2010 EchoStar Semtech SX1241 Remote 2011

Remote User Guide Safety Instructions You must keep safety in mind while using this device. Keep these and any other instructions for future reference. Observe Warnings: Carefully follow all warnings on the device and in the operating instructions. Heat: Do NOT place the device near heat sources such as radiators, stoves, heat registers, or other appliances that produce heat. Care and Use Cleaning: Do NOT use liquid, abrasive, solvent, or aerosol cleaners. Use a damp cloth for cleaning. When Not in Use: Remove the batteries if this device is to be left unattended or unused for a long period of time. Refer servicing to qualified personnel when a solid object or liquid has fallen onto or into the device. Do NOT attempt to service this device. Refer all servicing to qualified personnel. Opening covers other than the battery cover will void the warranty. Publishing Information Copyright 2011. EchoStar Technologies L.L.C., Englewood, Colorado 80112. All rights reserved. The information in this User Guide may change without notice. Revisions may be issued to tell you about such changes. Send comments or questions about this User Guide to techpubs@echostar.com or Technical Publications, EchoStar Technologies L.L.C, 90 Inverness Drive Circle East, Englewood, Colorado 80112. Document Number: 180532 Printed in DISH Network is a trademark and service mark of DISH Network. All product names, trade names, or corporate names mentioned in this User Guide are acknowledged to be the proprietary property of the registered owners. Configuring the 20.1 Remote The 20.1 remote does not require any configuration. Go to Insert the Batteries (page 2). Configuring the 21.1 Remote Complete the following steps to configure your remote. 1 2 3 4 Pull the remote battery cover off. Decide whether to use IR or UHF signals for the remote. Use UHF signals if you do not have a clear line of sight between the remote and the receiver. Set UHF/IR SWITCH to either UHF or IR. If your remote has a blank, black key, continue to Insert the Batteries on page 2. If your remote shows a 1 or a 2 on the bottom, you can pull out this key and flip it to the other number (2 to 1 and 1 to 2). To separate the key from the remote, insert your thumbnail or a coin in the crease. Remove the key by grasping at the bottom. Insert the key you wish to use to designate the remote and slide into place. Usually a 1 = TV1 and a 2 = TV2. For remotes showing the blank, black key, leave this key as it is. 1 Insert the Batteries 1 2 3 Pull the remote battery cover off. Insert 4 AAA batteries, making sure to match the plus (+) ends with the plus markings on the battery case. Replace the remote battery cover. 2 Using System Wizard Note: Not all receivers support System Wizard. If System Wizard does not appear, continue with page 4 or page 5 to make your remote work with your receiver. Use System Wizard initially to set up the remote to work with the receiver. System Wizard can also store/

restore your remote settings. Note: If your batteries are low, replace them before beginning. 1 2 3 4 Press and hold 0 until System Wizard message appears. Make sure the remote and receiver are in line of sight. If first time in System Wizard, follow instructions provided. When green checkmark displays, select Advanced to store/

restore remote settings. Follow the on-screen options. Select Continue to return to Live TV. 3 Making 20.1 and 21.1 IR Remote Work with Receiver For 20.1 and 21.1 IR Use the following instructions to configure your remote while using IR signals. Note: Use these instructions if your receiver does not support System Wizard. 1 2 3 4 Turn your receiver and TV on, and press SYSTEM INFO on the front of the receiver. Confirm that you see the System Info screen. 1 Press RECORD on your remote. The receiver then matches the remotes address. Confirm that your remote operates your receiver by pressing remote buttons. If this is not working, go back to step 3. 4 Making 21.1 UHF Remote Work with Receiver For 21.1 UHF Use the following instructions if you have configured your remote to use UHF signals. Note: Use these instructions if your receiver does not support System Wizard. 1 2 3 4 5 Verify the UHF antenna is installed on the back of the receiver. Turn your receiver and TV on, and press SYSTEM INFO on the front of the receiver. Confirm that you see the System Info screen. 1 1 Press RECORD on your remote. The remote address will probably change on the screen. Confirm that your remote operates your receiver by pressing remote buttons. If this is not working, go back to step 4. 5 SAT Mode SAT To use the features described in this section, make sure you are in SAT mode by pressing the SAT Mode button. Note: Some features may not be available depending on your receiver model. Press this button for SAT Mode Receiver Power & TV Power Top button turns the receiver on/off Bottom button turns the TV on/off Input Press once for Input Press and hold for Recover Receiver Menu Access receiver features and settings Volume and Mute Buttons Control TV volume Programming required Themes Search for programs using Themes Recall Return to last TV channel viewed Info Get info on programs Search Search for a program Shortcut Keys

(for future use) Digital Video Recorder (DVR) Buttons Pause live TV and play or record programming Format Format the picture to the desired width to match the program you are viewing Picture-In-Picture

(PIP) Buttons Watch two separate programs at once

(in Single Mode) DishHOME Explore interactive TV features 6 Page Buttons Page up/down in menus Program Guide Display current and future satellite program listings Browse See what is on other channels while watching TV Cancel Return to previous menu or to watching a program Arrow/Select Buttons Channel up/down, navigate through menus, and select a desired option View Satellite Programming Exit out of any menu/guide and return to viewing live TV Number Buttons Enter a channel number or navigate through menus System Wizard Press and hold to fix remote control issues and sync data TV Mode TV Receiver Power

& TV Power Turn the TV on/off Volume Control TV volume Up/Down Arrow Buttons Channel up/

down on TV Number Buttons Enter a desired channel number on TV Press this button for TV Mode Input Switch between TV inputs TV Menu Access menu features available on some TVs Mute Turn TV volume on or off Recall Return to last TV channel viewed Picture-In-Picture

(PIP) Buttons Display PIP features on some TVs with PIP capabilities 7 DVD Mode DVD DVD/VCR Power

& TV Power Top button turns the DVD player/VCR power on and off Bottom button turns the TV on and off Input Switch VCR between its TV & VCR mode Back Rewind a videotape or reverse a DVD Stop Stop playing a DVD, stop playing or recording a videotape Record Record on a videotape Press this button for DVD Mode Up/Down Arrow Buttons Channel up/

down on VCR Pause Pause a videotape or DVD FWD Forward a videotape or DVD Play Play a videotape or DVD Number Buttons Enter a channel number for DVD 8 DVR Functions Press twice to go to the list of recorded programs. Plays a live or recorded program. Pauses a live or recorded program. Stops recording a program. Records a program. Press BACK once to reverse the program four times as fast as normal play. Press BACK twice to reverse at 15 times normal speed, three times to reverse at 60 times normal speed, and four times to reverse at 300 times normal speed. The on-screen bar shows how far youve gone. For a live program, you can only reverse back to the last channel change or back one hour, whichever occurs first. Press SKIP BACK to skip back about 10 seconds in a program. Press FWD (Forward) once to fast-

forward through the program four times normal speed. Press FWD twice to forward at 15 times normal speed, three times to forward at 60 times normal speed, and four times to forward at 300 times normal speed. 9 DVR Functions, continued The on-screen bar shows how far youve gone. Of course, you cannot forward into the part of a live program that has not been broadcast yet. Press and release to skip forward through recorded programs. Press and hold before releasing to fast-forward quickly (x4). If pressed and released once in fast-forward mode, forwarding video increases to second speed (x60). Press SKIP FWD to skip ahead about 30 seconds in the program. Press PAUSE and then press BACK to reverse the program in slow motion at 1/4 the speed of normal play. Press BACK again to reverse at normal speed. Press PAUSE and then press FWD to forward the program in slow motion at 1/15 the speed of normal play. Press FWD twice to forward at 1/4 as fast as normal play. Press FWD three times to play the program. Of course, you cannot forward a live program that has not been broadcast yet. Press PAUSE and then press SKIP BACK to reverse the recording frame-

by-frame. Press PAUSE and then press SKIP FWD to advance the recording frame-

by-frame. 10 Programming Remote to Control Another Device Entering a Code TV Codes This table contains the manufacturer codes for programming the remote control to operate your TV. If your TV brand is not listed or if the codes do not work, the remote may not control your TV. In some cases, codes may operate some, but not all buttons, shown in this guide. Note: If programming a second TV in AUX mode, press 0 before entering the TV code. Abex 658 ABS 721 Accurian 623 Acer 511 Admiral 514 521 532 533 572 665 675 726 739 740 834 835 Advent 502 653 842 912 Aiko 524 727 778 Aiwa 667 Akai 506 520 592 601 612 622 627 652 680 684 738 750 754 794 795 807 808 858 865 866 906 907 908 Alaron 532 Albatron 692 804 Alienware 721 A-Mark 804 America Action 541 657 682 Ampro 691 Amtron 657 Anam 541 657 682 Anam National 541 657 AOC 505 506 519 520 582 620 627 653 654 913 Apex Digital 542 552 574 595 743 744 745 757 759 771 815 Archer 804 Astar 594 ASA 514 665 Audiovox 524 528 531 541 565 623 624 657 678 682 697 719 727 778 810 816 832 Autovox 514 665 Aventura 527 569 694 733 841 846 Axion 636 Bang & Olufsen 514 665 Barco 770 824 825 826 828 Baycraft 536 Baysonic 682 Belcor 505 627 773 Bell & Howell 590 611 675 683 Benq 511 535 Bradford 541 657 682 Brillian 558 Brionvega 514 665 Brockwood 505 627 Broksonic 533 622 648 682 726 748 750 752 754 834 865 866 899 908 byd:sign 792 C & M 804 Candle 506 520 523 536 627 654 Capehart 627 Carnivale 506 520 627 Carver 621 656 674 761 792 818 897 CCE 528 816 Celebrity 500 640 652 677 758 781 783 795 797 798 837 844 Celera 743 744 745 815 Century 514 665 Changhong 743 744 745 815 Cineral 697 Circuit City 627 Citizen 506 516 520 523 524 536 590 622 627 654 655 657 658 664 680 702 727 750 754 778 865 866 908 Clarion 541 657 682 Coby 607 626 633 Colortyme 627 654 Colt 660 Table continued on next page 29 1 2 3 4 Turn the device and receiver on. Find the brand name of the device listed in the code tables that start on page 29. Press and hold the Mode button until all the other Mode buttons light up. Once Mode buttons are lit, release the button. For AUX Mode only. Press 0 for second TV. 1 for a second DVD/VCR. 2 for a tuner, amplifier, or audio receiver. Enter one of the three-digit device codes from the table using buttons on the number pad, such as device code 560. If you want to program Limited Mode, see Placing Remote in Limited Mode on page 15. 11 Programming Remote to Control Another Device Entering a Code, continued 5 6 7 8 Press POUND (#). The Mode button flashes three times. Turn device on and try other buttons to make sure the device responds the way you expect. If you want to try another code, begin from Step 1 again. Turn off the device. If you are unable to find a code that works or if all the keys are not supported, go to Learning From Another Devices Remote on page 24 to program the key to the DISH Network remote. If you are unable to find a code that works, try the instructions for Scanning the Remote Database on page 13. 12 Programming Remote to Control Another Device Scanning the Remote Database 1 2 3 4 5 6 Turn the device and receiver on. Press and hold the correct Mode button for the device until all Mode buttons light up. Skip this step if programming TV or DVD Mode buttons. For AUX Mode only. Press 0 for second TV. 1 for second DVD/VCR. 2 for tuner, amplifier, or audio receiver. Press the STAR (*) button. Press and release UP ARROW slowly. When the device turns off, continue to Step 5. If the device remains on, continue pressing UP ARROW. When all codes have been tried, the Mode button flashes eight times. Try Learning From Another Devices Remote on page 24. Press POUND (#). The Mode button flashes three times. Turn the device on and try other buttons to make sure the device responds the way you expect. If not, try another code by returning to Step 1. 13 Displaying Device Code To identify the device code that your remote control is using, complete the following steps:

1 2 3 4 Press and hold the Mode button until all the Mode buttons light up and then release it. When you release the Mode button, the selected Mode button flashes. Press and release POUND

(#) twice. The Mode button flashes a number of times corresponding to the value of the stored device code. For example, if the stored device code is 593, the Mode button flashes five times, pauses, flashes nine times, pauses, and flashes three times. A quick flash is for zero. For AUX mode: The first group of flashes tells you what the AUX mode controls, then the following flashes tell you each digit of the devices code. Record the stored device code in the Reference Table on the inside back cover. 14 Placing Remote in Limited Mode Limited Mode locks out all the device mode operations except for the devices power, Mute, and Volume. This prevents you from accidentally tuning away from satellite programming. Note: Limited Mode cannot be used with audio amplifiers. 1 2 3 Press and hold the TV, DVD, or AUX Mode button until all Mode buttons light up. Press PAGE UP to activate. Press PAGE DOWN to take the remote out of Limited Mode. Press POUND (#). 15 SAT Auto-Tune SAT Auto-Tune programs into the remote control the correct TV channel used for viewing your paid programming. If you are experiencing fuzzy, snowy, blue, or black screens, it might be due to the TV being set to the wrong channel. Using the SAT Auto-

Tune feature helps prevent these screen issues from occurring on TVs connected to the receivers modulated output (usually TV2). Use SAT Auto-Tune to program the correct TV channel for satellite viewing into the remote control. When TV is pressed and released, the remote sends that channel to the TV, ensuring that the TV is on the correct channel for viewing your paid programming. This feature is enabled by default; however, if you want to use this feature, the channel must be programmed by following the steps in Setting SAT Auto-Tune Channel. Setting SAT Auto-Tune Channel 1 Make sure the remote control operates your TV. 2 3 4 5 6 Enter the channel used for viewing (two or three digits in range of 002 to 125), for example channel 10 or 010. Press POUND (#). The Mode button flashes three times to indicate programming was successful. Press SAT. The channel changes. Press and hold TV for three seconds until all four Mode buttons are lit. Press STAR (*). 16 Enabling and Disabling SAT Auto-Tune Note: SAT Auto-Tune is enabled by default; however, the channel must be set (see Setting SAT Auto-Tune Channel on page 16). 1 2 3 Press and hold SAT for three seconds until all four Mode buttons are lit. Press STAR (*). Press VOLUME UP to enable SAT Auto-Tune or VOLUME DOWN to disable. Press POUND (#). Press and hold the TV mode button until it stays lit. 4 Removing SAT Auto-Tune Channel 1 2 3 4 Press POUND (#). Enter 00 or 000. Press STAR (*). 17 Setting Auto-Tune for DVD/VCR You can set Auto-Tune for your DVD and/or VCR. Auto-Tune allows you to return to the channel for your DVD/VCR output when you accidentally change the channel or video input. 1 2 3 4 5 Make sure the remote control operates your DVD/VCR. Press and hold DVD for three seconds until all four Mode buttons are lit. Press STAR (*). Enter the channel used for viewing (two or three digits in range of 002 to 125), for example channel 03 or 004. Press POUND (#). The Mode button flashes three times to indicate programming was successful. 18 Removing Auto-Tune for DVD/VCR If you want to remove Auto-Tune for your DVD and/or VCR, follow the steps below. 1 2 3 4 Press and hold DVD until it stays lit. Press STAR (*). Enter 00 or 000. Press POUND (#). 19 Recovering Your Picture Use the RECOVER button to get back to watching satellite programming if you accidentally change channels or inputs on your TV, DVD, and/

or VCR. To use this feature, you must set up Auto-Tune for your TV (see page 16) and for your DVD/VCR (see page 18). Note: RECOVER only works if the remote control has been set up to control the TV and/or DVD/VCR, if connected. If the RECOVER button is used, the TV channel programmed for SAT Auto-Tune is also the channel that is sent to the TV. RECOVER first tries to tune your TV to channel 3, then channel 4, and then other video inputs with each press of the RECOVER button. You may need to press the RECOVER button up to 30 times to recover your satellite TV video. 1 2 3 4 Press and hold RECOVER until all Mode buttons light up. If you see the System Info screen, proceed to step 4. Otherwise, continue to step 3. Press RECOVER again and wait until the Mode lights stop flashing. If you see the System Info screen, go to step 4. If not, repeat this step until you see the screen. Press SELECT to resume watching TV. 20 Control Amplifier Volume When the remote control is set up to operate your TV, the MUTE and VOLUME buttons adjust your TV volume when in SAT mode. To use the remote to adjust the volume of a remote-controllable audio receiver or amplifier instead of adjusting the TVs volume setting, use the steps on this page. 1 2 3 4 5 Press and hold AUX until all Mode buttons are lit, then release it. The AUX mode button blinks. Press POUND (#). Press the plus (+) side of the VOLUME button. Press the 0 number button. Press POUND (#). The AUX mode button flashes three times. Make sure the remote controls the amplifiers volume in other modes:

6 7 8 Press SAT. Press the plus (+) and minus

(-) sides of the VOLUME button. Your tuner/amplifiers volume changes, and the AUX mode button lights. 21 Control TV Volume Use this procedure to change from having the remote adjust the volume of a audio receiver or amplifier to having the remote adjust the TVs volume. When the remote control is set up to operate your TV, the MUTE and VOLUME buttons adjust your TV volume when in SAT mode. 1 2 3 4 5 Press and hold TV until all Mode buttons are lit, then release it. The TV mode button blinks. Press POUND (#). Press the plus (+) side of the VOLUME button. Press the 0 number button. Press POUND (#). The TV mode button flashes three times. Make sure the remote controls the TVs volume in other modes:

6 7 8 Press SAT. Press the plus (+) and minus

(-) sides of the VOLUME button. Your TVs volume changes, and the TV mode button lights. 22 Programming Remote to Control Second Receiver in AUX Mode If you have another DISH Network receiver installed, you can use this remote control in AUX mode to operate your new receiver. AUX mode uses only IR signals, so the line of sight to the second receiver must be unobstructed. You can program the remote control to operate any other DISH Network receiver except where UHF is used, such as TV2 on DISH Network receivers. 1 2 3 4 5 6 Turn on the second receiver and open System Info screen. Write down the TV2 address that is shown. Press and hold AUX until all Mode buttons light up, then release the button. AUX flashes. Use the Number Pad on the remote control to enter a 3, followed by the address in step 2. Press POUND (#). AUX flashes three times. Press RECORD to verify that the address in the remote control now matches the address for the receiver. 23 Learning From Another Devices Remote Use this procedure if you are unable to find a code that allows your DISH Network remote to control your device. This procedure is also applicable if, after you have programmed your DISH Network remote to control your device (in TV, DVD, or AUX modes), some of the commands are not functioning as you expect. The learning function of your DISH Network remote control can support these commands. The remote control can learn commands in one of two ways:

You can follow the instructions for using device codes to program a specific mode, and then learn commands that add new or overwrite existing functions of the remote controls buttons in this mode. For this type of learning, any button without a learned command keeps the previous command (if any) for that device code. Each button on this remote learns a command from the devices original remote control. For this type of learning, any button without a learned command keeps the previous command (if any) for that device code. can be learned to turn the devices Learning can occur only in TV, DVD, or AUX modes. The Mode buttons (SAT, TV, DVD, and AUX) cannot learn a command. For each Mode button, the POWER button associated with that Mode on and off. Note: The TV Power button in all Modes. It cannot be learned. Note: The remote times out if a button isnt pressed within 20 seconds. If the remote times out, then the learning process needs to start over again. To teach the DISH Network remote control specific commands for another device, complete the following steps. turns the TV on and off 24 Learning from Another Devices Remote, continued 1 2 Ensure the DISH Network remote control is programmed to the desired remote address

(see page 4 or 5). Place both the DISH Network remote and the original devices remote control on a flat, stable surface. Point the front of the original devices remote to face the small square (IR window) on the front, left-hand side of the DISH Network remote, as shown below. The remotes should be no more than 3 apart. 3 4 On the DISH Network remote, press and hold the Mode button you want to use for the device until all the Mode buttons light up (approximately three seconds), and then release it. The selected Mode button blinks continuously. To start learning commands for this mode, select one of the following choices:

If youve found a code for the device, first program the code using the instructions for Entering a Code on page 11 or Scanning the Remote Database on page 13. If the device code has been programmed, press and release RECALL RECALL is pressed and comes on when button released), then hold the RECORD until the Mode button is lit again (about three seconds). The Mode button remains lit while learning.

(the Mode light goes off when If the device code has not been programmed for that device or if you are unable to find a code, press and hold the RECORD Mode button is lit (about three seconds). The button remains lit while learning. button until the 25 Learning from Another Devices Remote, continued 5 6 On the DISH Network remote, press the button you want to teach. The Mode light goes off and comes back on. On the original devices remote control, press and hold the button you want learned until the Mode light goes out and comes back on. You may need to press the button on the original remote several times for the DISH Network remote to learn the command. If the DISH Network remote learns the command, the Mode light blinks off and then back on. If the Mode light blinks three times or remains lit, the DISH Network remote did not learn the command. 7 8 After a button has learned a command successfully, repeat step 5 and step 6 until all commands you want have been learned. Press one of the Mode buttons on the DISH Network remote to end the learning sequence. This saves all the commands for that mode and exits learning to return to normal remote control operation. To cancel learning, do not press any buttons on either remote control for at least 30 seconds. The DISH Network remote control times out and returns to normal operation. Note: If the remote control batteries are too low for learning, all the Mode buttons blink quickly eight times. Learning ends without saving learned commands, and the remote returns to normal operation. Change the batteries and begin learning again. Note: No learned commands are saved if the DISH Network remote control times out before completion. 26 Discrete Codes Discrete On and Off IR-only remote-control commands are used by installers when programming macro commands into universal remotes. Using an On-only or Off-only command is more effective than a toggle On/Off command when trying to ensure the receiver is reliably in one state or the other. 1 2 3 4 5 Program the DISH Network remote to the desired remote address

(see Changing the Remote and Receiver Address, page 28). Hold SAT until all Mode buttons light, then release the button. Press POWER (not TV POWER). Press VOLUME UP for discrete power on. Press VOLUME DOWN for discrete power off. Press any other button when done to end this procedure. 27 Changing the Remote and Receiver Address If you notice that your receiver is changing channels or opening menus, but youre not using the remote control, changing the address should fix the problem. 1 2 3 4 5 6 Press SYSTEM INFO on the receivers front panel. Write down the TV2 remote address shown on the System Info screen. Press and hold SAT on your remote control for about three seconds, until all the Mode buttons light up, and then release SAT. Add one to the address that you wrote down in step 1, and use the NUMBER PAD to enter that number (between 1 and 28). Press POUND (#). Press RECORD. Press several buttons on the remote to make sure it is working as expected. 28 TV Codes This table contains the manufacturer codes for programming the remote control to operate your TV. If your TV brand is not listed or if the codes do not work, the remote may not control your TV. In some cases, codes may operate some, but not all buttons, shown in this guide. Note: If programming a second TV in AUX mode, press 0 before entering the TV code. Abex 658 ABS 721 Accurian 623 Acer 511 Admiral 514 521 532 533 572 665 675 726 739 740 834 835 Advent 502 653 842 912 Aiko 524 727 778 Aiwa 667 Akai 506 520 592 601 612 622 627 652 680 684 738 750 754 794 795 807 808 858 865 866 906 907 908 Alaron 532 Albatron 692 804 Alienware 721 A-Mark 804 America Action 541 657 682 Ampro 691 Amtron 657 Anam 541 657 682 Anam National 541 657 AOC 505 506 519 520 582 620 627 653 654 913 Apex Digital 542 552 574 595 743 744 745 757 759 771 815 Archer 804 Astar 594 ASA 514 665 Audiovox 524 528 531 541 565 623 624 657 678 682 697 719 727 778 810 816 832 Autovox 514 665 Aventura 527 569 694 733 841 846 Axion 636 Bang & Olufsen 514 665 Barco 770 824 825 826 828 Baycraft 536 Baysonic 682 Belcor 505 627 773 Bell & Howell 590 611 675 683 Benq 511 535 Bradford 541 657 682 Brillian 558 Brionvega 514 665 Brockwood 505 627 Broksonic 533 622 648 682 726 748 750 752 754 834 865 866 899 908 byd:sign 792 C & M 804 Candle 506 520 523 536 627 654 Capehart 627 Carnivale 506 520 627 Carver 621 656 674 761 792 818 897 CCE 528 816 Celebrity 500 640 652 677 758 781 783 795 797 798 837 844 Celera 743 744 745 815 Century 514 665 Changhong 743 744 745 815 Cineral 697 Circuit City 627 Citizen 506 516 520 523 524 536 590 622 627 654 655 657 658 664 680 702 727 750 754 778 865 866 908 Clarion 541 657 682 Coby 607 626 633 Colortyme 627 654 Colt 660 Table continued on next page 29 TV Codes, continued Commercial Solutions 503 522 645 650 749 776 779 805 830 831 859 863 864 Concerto 523 627 654 Contec 541 655 657 658 682 Craig 536 541 657 682 694 Crosley 500 621 640 656 674 677 758 761 781 783 792 795 797 798 818 837 844 897 Crown 536 541 655 656 657 658 682 702 761 CTX 804 Curtis 537 539 573 903 915 Curtis Mathes 503 506 516 520 521 528 530 531 572 590 611 621 627 641 645 650 654 655 656 658 674 675 680 683 697 702 719 738 739 740 749 755 761 776 792 794 818 830 832 863 864 897 CXC 541 657 682 CyberPower 721 Cytron 537 539 903 904 Daewoo 505 524 528 530 531 590 611 627 630 653 654 655 658 664 684 697 702 719 727 778 816 832 853 Daytron 505 627 654 658 Dell 518 676 772 773 774 Delta 909 Denon 786 Diamond Vision 546 643 659 Dimensia 503 645 830 DISH Network 742 Disney 529 559 Dixi 566 761 897 Dumont 501 505 627 711 775 813 Durabrand 527 529 533 541 559 564 569 587 627 632 657 682 694 718 726 733 834 841 843 846 Dwin 572 739 Dynex 538 585 698 701 706 EchoStar 742 763 Electroband 500 640 652 677 758 781 783 795 797 798 837 844 Electrograph 507 581 609 710 746 753 763 801 Electrohome 533 627 652 654 726 795 834 Element 567 568 591 669 723 724 902 Emerson 505 527 528 529 530 531 532 533 536 541 559 564 569 587 590 611 618 627 632 643 646 654 655 657 658 664 668 672 679 682 683 694 697 702 718 719 726 733 748 752 756 764 767 777 816 829 832 834 838 839 841 846 899 Emprex 597 Envision 506 519 520 620 627 654 Epson 708 ESA 527 569 587 601 618 632 646 679 694 733 767 777 829 838 839 841 846 Fisher 590 595 611 683 Fujitsu 532 536 602 603 694 Funai 500 527 532 541 569 587 618 640 657 677 679 682 694 733 756 758 777 781 783 795 797 798 829 837 838 839 841 844 846 Futuretech 541 657 682 694 Gateway 507 511 535 581 609 710 721 746 753 763 801 General Electric 503 508 522 528 531 544 564 627 645 650 654 661 690 697 718 719 742 749 776 779 805 830 831 832 859 863 864 GFM 527 529 559 569 618 679 694 733 777 829 838 839 841 846 Table continued on next page 30 TV Codes, continued Gibralter 501 505 506 520 627 711 775 813 Go Video 696 Goldi 566 Goldstar 505 506 520 523 564 566 627 653 654 655 658 702 718 720 761 897 GPX 532 Gradiente 540 Granada 627 Grand 627 Grundig 603 Grunpy 532 541 657 682 Haier 515 571 693 843 Hallmark 564 627 654 718 Harley Davidson 532 756 Harman/Kardon 621 627 656 674 761 792 818 897 Harvard 541 657 682 Havermy 521 572 739 740 Helios 901 905 Hello Kitty 528 531 697 719 832 Hewlett Packard 599 712 721 911 Hisense 759 Hitachi 517 523 547 549 554 555 606 627 637 638 654 655 658 675 688 709 756 786 788 789 790 791 Howard Computers 721 HP 599 712 721 911 Hush 721 Hyundai 695 iBUYPOWER 721 Ilo 529 559 588 596 625 668 764 IMA 657 Infinity 566 621 656 674 761 792 818 897 InFocus 616 Initial 596 625 Insignia 527 533 537 538 539 543 550 553 569 585 618 671 679 694 698 701 726 728 733 751 766 773 777 809 829 834 838 839 841 846 857 903 Inteq 501 711 775 813 JBL 566 621 656 674 761 792 818 897 JC Penney see Penney JCB 500 640 652 677 758 781 783 795 797 798 837 844 Jensen 502 537 539 627 653 654 842 903 912 JVC 508 517 533 557 570 642 649 655 658 662 688 713 714 715 726 735 736 737 812 817 834 Kawasho 627 652 654 795 KDS 591 669 902 KEC 541 657 682 Kenwood 505 506 520 627 654 716 KLH 595 743 744 745 815 Kloss 627 657 Konka 510 KTV 506 520 541 627 655 657 658 682 702 LG 501 503 522 545 553 564 615 627 650 653 654 693 711 718 720 730 766 773 775 779 804 805 809 813 830 831 859 Linksys 721 Lloyds 627 756 Lloytron 658 Loewe 566 656 761 897 Logik 675 Luce 699 Luxman 523 627 654 LXI 503 526 564 566 590 595 611 621 627 631 635 645 650 654 656 674 683 718 744 749 761 768 771 776 785 792 818 830 863 864 897 M. Wards see Wards MAG 591 669 902 Magnasonic 664 756 Table continued on next page 31 TV Codes, continued Magnavox 506 507 508 517 520 527 532 536 550 560 563 566 569 581 609 618 621 625 627 646 654 656 674 679 688 694 710 733 746 747 753 756 761 762 763 767 777 782 792 801 818 827 828 829 838 839 841 846 876 887 888 891 892 893 894 897 Magnin 661 Majestic 675 Marantz 506 520 550 560 563 566 604 608 621 627 654 656 674 747 761 792 818 836 897 Matsushita 512 577 619 634 685 689 700 729 734 765 780 784 819 820 821 822 823 Maxent 507 581 609 710 746 753 763 801 Media Center PC 721 Megapower 804 Megatron 564 627 654 718 Memorex 504 529 532 533 559 564 590 611 613 627 648 653 654 675 680 683 684 718 725 726 752 787 799 834 869 876 899 MGA 504 505 506 520 564 613 627 653 654 661 718 725 787 799 Microsoft 721 Midland 501 508 645 650 655 658 702 711 730 749 775 776 813 863 864 Mind 721 Mintek 596 625 Mitsubishi 504 505 517 521 564 572 613 614 627 653 654 688 718 725 739 740 787 799 Mitsui 769 Monivision 692 804 Montgomery Wards see Wards Motorola 521 572 739 740 835 MTC 505 506 516 520 523 627 653 654 680 Multitech 541 657 682 Multivision 810 NAD 526 564 595 627 631 635 637 654 718 744 768 771 785 NEC 505 506 517 520 523 604 608 610 627 653 654 687 688 731 732 904 NetTV 507 581 586 609 710 746 753 763 801 Nikkai 613 Nikko 506 520 524 564 627 654 718 727 778 Niveus Media 721 Norcent 519 579 759 Northgate 721 Norwood Micro 588 Noshi 681 Novabeam 627 NTC 524 727 778 Nyon 627 Olevia 523 564 578 580 654 910 914 Onwa 541 657 682 Optimus 512 577 590 611 619 634 637 685 689 700 729 734 756 765 780 784 819 820 821 822 823 869 876 Optonica 521 572 739 740 835 Orion 532 533 538 694 726 748 752 834 899 Panasonic 508 509 512 576 577 619 634 644 647 656 685 689 700 729 734 761 765 780 784 811 819 820 821 822 823 860 861 862 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 889 890 895 896 897 900 Panavision 734 811 Table continued on next page 32 TV Codes, continued Penney 503 505 506 508 516 520 525 526 543 564 595 627 631 635 645 650 653 654 655 658 661 680 681 690 702 718 720 728 730 744 749 768 776 771 785 830 857 863 864 Petters 534 Philco 505 506 514 520 527 529 532 536 559 569 618 621 627 653 654 655 656 658 665 668 674 679 694 733 761 764 777 792 818 829 838 839 841 846 897 Philips 514 525 527 548 550 560 563 566 621 625 627 655 656 658 665 674 747 761 770 782 792 818 824 825 826 827 828 839 876 887 888 891 892 893 894 897 Pilot 505 506 520 627 655 658 702 Pioneer 547 561 576 604 608 627 637 654 Plasmsync 610 Polaroid 534 537 539 550 588 591 627 669 670 671 678 743 744 745 751 766 773 814 815 901 902 903 905 Portland 505 524 528 530 531 627 653 654 655 658 697 702 719 727 778 832 Price Club 680 Prima 502 653 673 674 842 912 Princeton 562 804 Prism 508 Proscan 503 506 520 522 645 650 705 742 749 776 779 805 830 831 859 863 864 Proton 536 564 627 654 655 658 718 Protron 589 Proview 591 669 902 Pulsar 501 505 627 711 775 813 Quasar 508 512 577 619 634 685 689 700 729 734 765 780 784 819 820 821 822 823 860 861 862 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 889 890 895 896 Radio Shack 503 505 506 520 541 564 590 611 627 645 650 655 657 658 662 682 683 702 718 749 756 776 830 863 864 RCA 503 505 508 521 522 530 544 547 627 630 636 637 639 641 645 650 651 653 654 661 671 681 686 690 740 742 749 751 776 779 805 830 831 859 863 864 902 916 Realistic 503 505 506 520 541 564 590 607 611 627 645 654 655 657 658 682 683 702 718 730 830 Ricavision 721 Runco 501 506 520 604 608 627 711 775 813 Sampo 506 507 520 581 609 627 654 655 658 702 710 746 753 763 801 Samsung 505 506 516 520 523 564 566 601 627 653 654 655 658 680 684 702 707 717 718 738 755 761 794 833 858 897 Samsux 655 658 702 Sansei 697 Sansui 527 533 569 622 694 726 733 748 750 752 754 756 834 841 846 865 866 899 908 Sanyo 517 590 611 621 627 656 661 674 683 688 761 792 818 840 897 SBR 566 761 897 Sceptre 677 Schneider 566 761 897 Scimitsu 505 773 Table continued on next page 33 TV Codes, continued Scotch 564 627 654 718 Scott 505 532 541 564 627 654 655 657 658 682 718 Sears 503 523 526 527 532 558 564 569 590 595 611 621 627 631 635 645 650 654 656 658 674 683 694 718 733 744 749 756 761 768 771 776 785 792 818 830 841 846 863 864 897 Seimitsu 627 Semivox 682 Semp 595 771 Sharp 521 546 556 572 605 627 628 629 654 655 658 663 702 739 740 803 835 836 898 Sharper Image 703 Sheng Chia 521 572 739 740 Shogun 505 627 Signature 621 656 674 675 761 792 818 897 Simpson 536 Solavox 613 Sole 699 Sony 500 513 640 652 677 721 756 758 781 783 795 796 797 798 806 837 844 845 Soundesign 532 536 541 564 627 654 657 682 718 Spectricon 520 627 Spectroniq 591 669 902 Squareview 527 569 694 733 841 846 SSS 505 541 627 657 682 Stack 9 721 Starlite 541 657 682 Studio Experience 692 Superscan 521 572 583 646 739 740 741 767 777 Supra 523 627 Supreme 500 640 652 677 758 781 783 795 797 798 807 837 844 SVA 515 618 679 759 777 829 838 839 901 905 Sylvania 506 520 527 529 536 559 566 567 568 569 618 621 627 646 654 656 668 672 674 679 694 723 724 733 756 761 764 767 777 792 818 829 838 839 841 846 888 897 Symphonic 527 541 569 587 632 646 657 679 682 694 733 756 767 841 846 Syntax 523 558 564 578 580 654 910 914 Systemax 721 Tagar Systems 721 Tandy 521 572 739 740 835 Tatung 511 535 588 Teac 586 Technics 508 512 577 619 634 685 689 700 729 734 765 780 784 819 820 821 822 823 Technol ACE 532 Techview 590 683 Techwood 508 523 627 654 Teco 704 Teknika 504 505 512 516 523 524 532 536 541 613 621 627 644 653 654 655 656 657 658 674 675 680 682 685 702 725 727 761 778 787 792 799 818 897 Telecaption 688 Telefunken 738 794 Thomas 627 756 TMK 523 564 627 654 718 TNCi 501 711 775 813 Toshiba 516 517 526 590 595 610 611 615 617 622 631 635 644 666 680 683 688 721 744 750 754 755 768 771 785 793 800 802 847 848 849 850 851 852 854 855 865 866 908 909 Totevision 655 658 702 Touch 721 Toyomenko 627 Table continued on next page 34 TV Codes, continued Zenith 500 501 506 520 524 530 533 553 555 564 615 627 638 640 645 675 677 711 718 720 726 727 748 749 752 756 758 766 773 775 776 778 781 783 795 797 798 809 813 834 837 844 853 863 864 899 Zonda 804 ZT Group 721 Trutech 529 559 584 TVS 533 726 834 Ultra 589 US Logic 588 V Inc. 562 575 Vector Research 506 520 627 VEOS 558 Victor 557 735 736 737 Vidikron 604 608 621 656 674 761 792 818 897 Vidtech 505 517 564 627 653 654 688 718 Viewsonic 507 551 562 575 579 581 582 583 600 606 609 620 710 721 741 746 753 760 763 789 796 801 Viore 907 915 Vizio 511 535 551 562 575 583 593 598 741 773 Voodoo 721 Wards 500 501 503 505 506 508 516 520 526 532 536 541 564 590 595 611 621 627 631 635 640 641 645 653 654 656 657 674 675 677 681 682 711 718 749 758 761 768 775 776 781 783 785 792 795 797 798 813 818 830 837 844 863 864 897 Waycon 526 595 631 635 768 785 Westinghouse 528 531 551 562 574 575 652 697 719 795 797 798 809 832 856 White Westinghouse 528 530 533 726 816 832 834 Yamaha 505 506 520 606 627 653 654 789 York 627 35 VCR Codes This table contains the manufacturer codes for programming the remote control to operate your VCR. If your VCR brand is not listed or if the codes do not work, the remote may not control your VCR. In some cases, codes may operate some, but not all, buttons shown in this guide. Note: If programming your VCR in AUX mode, press 1 before entering the VCR code. ABS 792 Accurian 544 588 Admiral 607 918 Adventura 544 588 594 Aiwa 501 512 544 588 594 676 678 Akai 513 515 516 518 525 568 682 772 Alienware 792 Allegro 502 522 529 533 678 779 American High 554 Americast 917 Apex Digital 517 851 ASA 556 801 Asha 591 675 Audio Dynamics 592 Audiovox 512 676 678 Bang & Olufsen 794 Beaumark 591 675 Bell & Howell 549 581 Broksonic 506 508 511 515 516 525 550 559 Calix 512 676 678 Candle 534 592 594 675 676 678 Canon 554 CineVision 502 522 529 678 779 Citizen 512 515 516 525 534 536 591 592 594 675 676 678 796 Colortyme 592 Craig 512 591 675 676 678 789 Crosley 544 588 Curtis Mathes 513 528 554 585 591 592 594 605 607 614 628 649 675 682 773 774 Cybernex 591 675 Cyberpower 792 Daewoo 502 522 529 534 536 559 588 678 779 796 Davidson 544 594 DBX 592 Dell 792 DiamondVision 532 641 Dimensia 585 607 649 Dumont 549 Durabrand 533 592 594 Dynatech 544 588 594 Electrohome 512 567 676 678 Electrophonic 512 676 678 Emerson 506 508 512 518 519 531 534 536 544 550 554 559 567 568 588 594 676 678 756 796 798 803 804 Emerex 500 790 ESA 502 522 529 531 678 779 803 804 Finlandia 549 Finlux 549 556 801 Fisher 549 581 789 Fuji 554 772 Funai 519 544 588 594 756 798 803 804 Garrard 544 588 594 Gateway 792 General Electric 528 541 554 585 591 605 607 649 675 773 774 GFM 519 803 Table continued on next page 36 VCR Codes, continued Go Video 502 507 522 524 529 591 675 678 779 912 Goldstar 502 507 512 522 529 592 594 676 678 779 Goodmans 585 Gradiente 544 588 594 Granada 549 Grundig 556 801 Harley Davidson 544 588 594 Harman/Kardon 568 592 594 Headquarter 581 Hewlett Packard/HP 792 Hi-Q 789 Hitachi 513 514 544 588 594 595 682 776 Howard Computers 792 HP see Hewlett Packard Humax 521 910 911 Hush 792 iBUYPOWER 792 Insignia 507 803 Instant Replay 554 ITT 675 JC Penney see Penney JCL 554 Jensen 513 595 682 776 JVC 513 523 526 527 545 561 562 581 592 594 682 795 KEC 512 676 678 Kenwood 513 523 526 527 562 581 592 594 682 795 Kodak 512 554 676 678 LG 502 507 522 529 676 678 779 Linksys 792 Lloyds 544 588 594 Luxor 567 LXI 512 676 678 M. Wards see Wards Magnasonic 536 756 796 Magnavox 519 531 533 544 554 556 588 594 756 783 797 798 801 803 804 Magnin 591 675 676 678 Marantz 554 556 581 585 592 594 801 Marta 512 676 678 Matsushita 554 614 628 799 806 Media Center PC 792 MEI 554 Memorex 506 512 515 516 525 533 544 549 550 554 581 585 588 591 594 607 614 628 675 676 678 770 771 777 780 781 782 784 786 787 788 789 799 806 809 918 MGA 512 567 568 591 675 MGN Technology 591 675 Microsoft 792 Midland 591 Mind 792 Minolta 595 776 Mitsubishi 512 523 526 527 562 567 568 595 607 776 795 Montgomery Wards see Wards Motorola 554 607 918 MTC 544 588 591 594 675 Multitech 544 588 591 594 NAD 507 NEC 513 523 526 527 549 562 581 592 594 682 795 Nikko 512 676 678 Nikon 791 Niveus Media 792 Noblex 591 675 Northgate 792 Olympus 554 Onkyo 783 Optimus 512 549 581 607 614 628 676 678 756 770 771 777 780 781 782 784 786 787 788 799 806 809 918 Optonica 585 Orion 550 559 Table continued on next page 37 VCR Codes, continued Panasonic 554 614 628 672 770 771 777 780 781 782 783 784 786 787 788 791 799 806 809 810 912 Penney 512 554 581 591 592 594 595 675 676 678 776 Pentax 594 595 776 Pentex Research 592 594 Philco 554 Philips 520 554 556 585 783 801 803 804 911 Pilot 512 676 678 Pioneer 523 526 527 562 776 795 Polaroid 517 530 Presidian 519 804 Profitronic 591 675 Proscan 528 585 605 607 649 773 774 Pulsar 533 Quarter 581 Quartz 581 Quasar 554 614 628 770 771 786 799 806 RadioShack 512 544 581 588 594 676 678 Radix 512 676 678 Randex 512 676 678 RCA 518 528 539 541 554 585 591 595 605 607 649 675 773 774 775 776 Realistic 512 534 544 549 554 581 585 588 594 607 676 678 789 918 Ricavision 792 Ricoh 791 Rio 502 522 529 678 779 Runco 533 Salora 567 Samsung 506 524 534 591 675 755 807 Sanky 533 607 918 Sansui 513 515 516 523 525 526 527 544 550 562 588 594 682 795 Sanyo 515 516 525 549 581 591 675 789 SBR 556 801 Sceptre 549 581 Scott 508 534 559 567 Sears 512 544 549 554 581 588 594 595 676 678 776 789 Sharp 512 585 607 918 Shintom 595 772 Shogun 591 675 Singer 554 791 Signature 554 Sonic Blue 502 522 529 678 779 907 912 Sony 500 544 554 588 594 768 772 778 790 791 792 919 Stack 9 792 STS 554 Superscan 531 798 804 Sylvania 519 531 544 554 556 567 588 594 756 797 798 801 803 804 Symphonic 519 531 544 588 594 756 804 Systemax 792 Tagar Systems 792 Tandy 581 Tashiko 512 676 678 Tatung 513 682 Teac 513 544 588 594 682 Technics 554 614 628 Teknika 512 544 554 588 594 676 678 Thomas 544 588 594 Tivo 510 520 521 537 548 905 906 908 909 910 911 TMK 591 675 Toshiba 513 515 516 525 534 537 538 542 543 567 682 769 776 783 792 Totevision 512 591 675 676 678 Touch 792 Table continued on next page 38 VCR Codes, continued UltimateTV 649 Unitech 591 675 Urban Concepts 672 783 Vector Research 534 592 594 Victor 561 562 Video Concepts 534 568 592 Videomagic 512 676 678 Videosonic 591 675 Viewsonic 792 Villain 544 588 594 Voodoo 792 Wards 512 528 533 534 544 554 585 588 591 592 594 595 605 607 649 675 676 678 772 773 774 776 789 918 White Westinghouse 588 XR-1000 544 554 588 594 Yamaha 581 592 594 682 Zenith 500 502 507 512 522 529 533 544 588 594 678 772 779 783 791 ZT Group 792 39 DVD Player Codes This table contains the manufacturer codes for programming the remote control to operate your DVD Player. If your DVD Player brand is not listed or if the codes do not work, the remote may not control your DVD Player. In some cases, codes may operate some, but not all, buttons shown in this guide. Note: If programming a DVD Player in AUX mode, press 1 before entering the DVD Player code. Accurian 602 617 619 658 661 674 764 829 Advent 572 759 Aiwa 694 Akai 646 656 709 725 740 751 752 754 814 815 Alco 765 Allegro 626 683 Amphion Media Works 586 711 AMW 586 711 Anam 688 Apex Digital 580 589 635 654 655 666 710 744 757 835 839 851 Apple 642 Archos 885 Arrgo 833 Aspire Digital 558 598 Astar 612 Audiovox 580 589 630 666 710 765 826 835 837 Axion 867 B&K 701 Bang & Olufsen 569 580 BBK 566 Bel Canto Design 719 878 Blaupunkt 580 589 666 710 835 Blue Parade 719 BOSE 758 811 Broksonic 646 656 709 725 752 754 814 815 California Audio Labs 662 697 699 716 733 737 840 841 855 Cambridge SoundWorks 870 CAVS 708 CineVision 626 683 Citizen 646 656 709 725 754 814 815 Classic 695 826 882 Coby 557 634 636 761 Criterion 712 Curtis 685 Curtis Mathes 684 CyberHome 833 Cytron 904 Daewoo 626 630 657 683 852 859 Daytek 711 Denon 578 662 697 699 700 716 718 733 737 840 841 855 892 Desay 598 Diamond Vision 637 641 Disney 617 619 658 661 674 764 829 Dual 871 Durabrand 826 833 848 DVD2000 699 716 Eltax 685 Emerson 570 617 619 631 639 645 650 651 658 661 674 679 764 829 Enterprise 824 ESA 570 587 631 639 650 651 679 Eastech 587 Entiveo 587 Fisher 609 659 705 Funai 570 617 619 631 658 661 674 679 764 829 Gateway 610 870 Table continued on next page 40 DVD Player Codes, continued General Electric 580 589 616 666 702 703 710 720 749 816 835 842 GFM 570 617 619 631 658 661 674 679 764 829 Go Video 610 611 615 626 673 683 691 692 693 741 820 821 822 824 826 896 899 Goldstar 611 615 626 673 683 824 899 GPX 704 826 882 Gradiente 699 716 723 745 Greenhill 580 589 666 710 835 Grundig 565 577 630 852 874 Harman/Kardon 715 Hitachi 606 652 660 668 705 706 707 823 844 860 866 Hiteker 654 655 744 839 iLive 856 Ilo 837 Initial 580 589 666 710 835 837 Insignia 570 617 619 631 647 658 661 673 674 679 717 738 764 824 829 857 871 Integra 551 583 584 719 890 Irradio 601 608 Jamo 728 JBL 715 Jensen 557 759 JMB 656 815 JVC 553 603 604 620 621 622 623 625 689 746 850 861 862 863 872 898 Jwin 742 Kawasaki 765 Kendo 848 Kenwood 579 662 697 699 700 716 733 737 840 841 855 KLH 580 589 666 710 765 835 Konka 753 Koss 564 723 745 873 Lasonic 593 Landel 680 Lenoxx 560 826 Lexicon 743 LG 611 615 626 673 683 824 899 Lifetec 634 Liquid Video 564 Liteon 602 610 Logix 852 Lumatron 673 824 Luxman 844 Luxor 848 Magnavox 565 570 572 577 601 608 617 619 631 639 650 651 658 661 672 674 679 764 803 804 829 854 874 Marantz 565 577 874 McIntosh 830 831 832 836 838 843 858 Memorex 646 656 658 709 725 754 760 814 815 Microsoft 576 616 702 703 720 749 816 842 Mintek 580 589 666 681 710 835 Mitsubishi 767 Momitsu 748 NAD 507 611 615 664 673 824 899 Nakamichi 596 Nesa 580 589 666 710 835 Next Base 680 Nexxtech 599 871 Niro 750 Norcent 634 711 871 Onkyo 551 583 584 672 890 Oppo 566 878 885 Oritron 564 723 745 Panasonic 624 627 638 662 663 672 687 697 699 714 716 733 734 737 813 840 841 855 Philco 617 619 658 661 674 764 829 Table continued on next page 41 DVD Player Codes, continued Philips 565 572 574 577 601 608 610 617 619 658 661 672 674 698 713 743 764 766 829 848 854 873 874 Pioneer 653 665 686 719 812 877 878 879 880 Polaroid 586 617 635 636 640 647 651 677 851 Polk Audio 565 577 874 Portland 751 Presidian 617 619 658 661 674 764 829 Prima 759 Proceed 654 655 744 839 Proscan 616 702 703 720 749 816 842 Provision 761 Pye 674 Qwestar 723 745 RCA 580 583 584 589 616 647 666 688 690 702 703 710 719 720 749 760 765 816 835 842 867 901 Regent 560 Rio 626 683 Rotel 553 850 861 862 863 Rowa 555 Saba 762 Sampo 724 865 Samsung 571 606 643 644 652 662 667 668 691 693 697 699 716 733 737 740 741 747 805 820 821 823 840 841 844 845 849 855 864 866 869 875 881 895 896 900 Sansui 646 656 709 725 754 814 815 Sanyo 609 646 656 659 705 709 725 754 814 815 Schneider 601 608 Sensory Science 610 Sharp 573 617 619 658 661 669 674 696 727 750 764 829 865 903 Sharper Image 763 Sherwood 751 870 Sherwood Newcastle 870 Shinco 589 Shinsonic 681 731 837 SonicBlue 626 683 Sony 582 613 618 632 670 671 729 730 731 817 818 827 830 831 832 836 838 843 846 847 858 868 883 884 902 Sungale 597 Superscan 531 570 639 650 651 803 804 SVA 800 Sylvania 531 570 617 619 631 639 645 650 651 658 661 674 679 764 803 804 829 Symphonic 531 617 619 639 650 651 658 661 674 764 803 804 829 Teac 732 765 Technics 662 697 699 716 733 737 840 841 855 Technosonic 886 Techwood 664 Terapin 887 Theta Digital 719 TiVo 888 Toshiba 575 583 584 646 648 656 672 709 721 725 735 736 754 814 815 819 825 828 834 876 888 893 894 Trutech 833 Urban Concepts 672 US Logic 681 Venturer 765 Vizio 726 897 Westinghouse 629 Xbox 576 616 702 703 720 749 816 842 Yamaha 565 577 601 602 608 662 697 699 716 733 737 739 840 841 853 855 874 889 891 YBA 711 Zenith 611 615 626 672 673 683 824 899 42 Tuner/Amplifier Codes This table contains the manufacturer codes for programming the remote control to operate your tuner/amplifier. If your tuner/amplifier is not listed or if the codes do not work, the remote may not control your turner/amplifier. In some cases, codes may operate some, but not all, buttons shown in this guide. Note: If programming a tuner/amplifier in AUX mode, press 2 before entering the Tuner/Amplifier code. Accuphase 690 Acoustic Research 703 853 Acurus 691 ADC 652 664 Adcom 644 673 Admiral 747 ADS 748 Advent 860 Aiwa 636 667 681 683 685 718 720 725 730 839 Akai 740 Alco 659 Altec Lansing 738 AMC 770 855 Amphion Media Works 660 Amplifier Technologies 710 AMW 660 Anam 653 776 Angstrom 692 Anthem 750 Apex Digital 812 Aragon 691 Arcam 725 726 Atlantic Technology 712 Audio Research 751 AudioSource 693 Audiotronic 685 Audiovox 659 826 B&K 752 Bang & Olufsen 676 Bel Canto Design 694 710 BOSE 639 656 704 753 761 Boston Acoustics 713 Brumester 647 California Audio Labs 686 Cambridge SoundWorks 831 Capetronic 652 664 798 Carver 681 685 718 720 725 Cary Audio Design 689 Casio 717 CCE 802 Cinema Sound 696 Clarinette 717 Classe 697 Classic 802 819 Coby 679 728 731 780 811 815 834 Counterpoint 754 Craig 856 Creative 723 Criterion 734 Crown 857 Curtis 731 777 780 811 815 Curtis Mathes 772 Daewoo 727 Dell 729 Denon 669 670 680 682 696 744 759 760 762 792 809 Dimensia 703 853 Durabrand 698 EAD 756 Eclipse 665 Elan 699 Emerson 820 Enlightened Audio Designs 756 ESA 757 Fisher 824 850 Fosgate 700 712 Garrard 758 851 Gateway 743 831 833 Glory Horse 728 Go Video 742 Table continued on next page 43 Tuner/Amplifier Codes, continued Goldstar 814 GPX 834 Hafler 758 Harman/Kardon 640 685 714 725 Hitachi 850 iLive 835 Initial 735 789 826 Insignia 711 770 825 Integra 650 695 785 788 790 791 838 Jamo 837 JBL 642 JC Penney see Penney Jensen 775 860 JVC 637 652 663 664 728 755 786 827 848 Kenwood 658 662 668 774 795 828 829 830 840 KLH 659 812 Klipsch 691 Knoll Systems 701 Koss 739 Lasonic 746 Left Coast 640 Lenoxx 698 736 Lexicon 724 LG 814 836 Linn 685 725 Liquid Video 739 Lloyds 717 Logitech 702 M. Wards see Wards Magnavox 652 664 685 717 725 Magnum Dynalab 858 Marantz 640 645 685 725 764 787 854 Mark Levinson 705 McIntosh 645 706 764 MCS 719 Memorex 777 Midiland 707 Mitsubishi 859 Modulaire 717 Mondial 691 Motorola 737 NAD 648 Nakamichi 649 658 NEC 641 Nexxtech 711 825 Nikko 708 Niro 779 Norcent 711 731 780 811 815 825 834 Nova 731 780 811 815 834 Omnifi 745 Onkyo 650 671 695 785 788 790 791 822 838 Optimus 635 652 653 664 772 775 798 824 842 845 Oritron 739 Outlaw 712 Panasonic 643 672 677 678 715 749 768 783 797 799 804 805 808 810 816 817 818 821 843 Parasound 647 Penney 717 Philco 781 Philips 640 685 716 721 725 726 751 860 Pioneer 635 652 664 666 675 767 772 798 806 813 842 844 845 Polaroid 679 812 Polk Audio 640 645 685 725 764 Prima 860 Proscan 703 852 853 Pyle 782 Quasar 799 RadioShack 728 RCA 635 652 653 659 664 675 703 719 772 776 842 845 852 853 Realistic 717 747 Regent 736 Rio 661 729 Rotel 674 Table continued on next page 44 Tuner/Amplifier Codes, continued Saba 741 Samsung 688 807 Sansui 685 719 725 Sanyo 824 850 Sharp 832 Sharper Image 728 Sherwood 743 770 831 833 Sherwood Newcastle 743 833 Shinsonic 735 789 826 Shure 641 Sonic Blue 661 729 742 Sonic Frontiers 750 Sony 638 654 683 730 765 766 769 771 773 778 784 793 794 803 846 Soundesign 708 Soundmatters 763 SpeakerCraft 763 Stereophonics 635 842 845 Sunfire 658 840 Symphonic 747 TAG McLaren 796 Teac 653 659 851 Technics 643 672 768 804 805 808 810 843 Techwood 798 Thomson 800 Thorens 685 Toshiba 675 822 Vector Research 801 Venturer 659 Victor 637 827 Vizio 709 831 Wards 635 685 725 730 853 Yamaha 646 650 651 655 657 663 684 687 732 733 786 823 841 847 848 849 Yorx 708 717 Zenith 814 45 DVR Codes This table contains the manufacturer codes for programming the remote control to operate your DVR. If your DVR brand is not listed or if the codes do not work, the remote may not control your DVR. In some cases, codes may operate some, but not all, buttons shown in this guide. Note: If programming a DVR in AUX mode, press 1 before entering the DVR code. ABS 792 Alienware 792 Americast 917 Bang & Olufsen 794 BellSouth 917 CyberPower 792 Dell 792 Director 913 Gateway 792 870 General Instrument 913 GOI 722 Hewlett Packard 792 HNS 521 Howard Computers 792 HP 792 HTS 722 Hughes Network Systems 521 910 Humax 910 Hush 792 iBUYPOWER 792 Jerrold 913 JVC 722 746 Linksys 792 Media Center PC 792 Microsoft 576 616 702 703 792 842 Mind 792 Motorola 913 Niveus Media 792 Northgate 792 Pace 914 Panasonic 687 697 733 907 Philips 521 548 574 601 608 610 619 658 661 674 698 713 743 829 848 854 906 910 Pioneer 653 686 878 914 Proscan 616 702 703 842 916 RCA 521 580 583 584 589 647 688 702 703 710 760 867 911 916 ReplayTV 907 912 Samsung 521 662 693 697 733 737 747 823 840 841 855 864 Scientific Atlanta 914 Sharp 573 619 658 661 674 696 750 764 829 Sonic Blue 626 907 Sony 510 792 905 908 909 Stack 9 792 Supercable 915 Systemax 792 Tagar Systems 792 Tivo 510 520 548 905 906 908 909 910 911 Toshiba 709 721 725 754 792 876 888 Touch 792 UltimateTV 916 Viewsonic 792 Voodoo 792 Zenith 615 626 683 899 917 ZT Group 792 46 Combo Codes This following tables contain the manufacturer codes for programming the remote control to operate combined devices. If your combined device brand is not listed or if the codes do not work, the remote may not control your combined device. In some cases, codes may operate some, but not all, buttons shown in this guide. 645 661 749 776 TV/VCR Codes Note: Program the remote control in TV mode using the TV code and then in DVD mode (or in AUXpress 1 before entering the VCR code) using the VCR code. Aiwa TV Code 667 VCR Code 501 America Action TV Code 541 657 662 682 Audiovox TV Code 541 657 662 682 Bang & Olufsen TV Code 665 VCR Code 537 Broksonic TV Code 748 752 899 Citizen TV Code 664 VCR Code 536 796 Colt TV Code 660 VCR Code 535 Curtis Mathes TV Code 755 Daewoo TV Code 664 VCR Code 536 796 Emerson TV Code 664 748 752 756 899 VCR Code 536 756 796 Funai TV Code VCR Code 533 544 588 General Electric TV Code 863 864 VCR Code 591 675 GoldStar VCR Code 676 Gradiente TV Code 540 Harley Davidson TV Code 756 VCR Code 533 544 588 Hitachi TV Code 756 VCR Code 533 544 588 JVC TV Code 557 649 735 736 737 VCR Code 545 Lloyds TV Code 756 VCR Code 533 544 588 Magnasonic TV Code 664 756 VCR Code 536 756 796 Magnin TV Code 661 VCR Code 591 675 MGA TV Code 661 VCR Code 591 675 Table continued on next page 47 756 Combo Codes, continued TV/VCR Codes, continued Magnavox TV Code 756 876 887 888 891 892 893 894 VCR Code 533 544 588 756 797 Memorex TV Code 869 VCR Code 614 628 676 770 771 777 780 781 782 783 784 786 787 788 799 806 809 Optimus TV Code 756 869 VCR Code 614 628 756 770 771 777 780 781 782 783 784 786 787 788 799 806 809 Orion TV Code 748 752 899 Pansonic TV Code 647 765 811 860 861 862 867 868 869 870 871 872 873 874 875 877 878 879 880 881 882 883 884 885 886 889 890 895 900 VCR Code 614 628 770 771 777 780 781 782 783 784 786 787 788 799 806 809 Penney TV Code 661 VCR Code 591 675 676 Philips TV Code 876 887 891 892 893 894 VCR Code 801 RadioShack TV Code 756 VCR Code 533 544 588 Quasar TV Code 860 868 869 870 VCR Code 614 628 799 806 RCA TV Code 641 645 661 776 863 864 VCR Code 591 675 Samsung TV Code 755 VCR Code 755 775 807 Sansui TV Code 748 752 756 899 VCR Code 533 544 588 Sanyo TV Code 661 VCR Code 591 675 Sears TV Code 756 VCR Code 533 544 588 676 Sharp TV Code 521 546 556 740 Sony TV Code 500 640 677 756 758 781 783 795 797 798 837 844 VCR Code 533 544 588 Sylvania TV Code 887 888 891 892 893 894 VCR Code 797 Table continued on next page 48 Combo Codes, continued TV/VCR Codes, continued Symphonic TV Code 756 VCR Code 533 544 588 756 Thomas TV Code 756 VCR Code 533 544 588 Toshiba TV Code 617 666 755 VCR Code 538 542 543 769 Zenith TV Code 748 752 756 899 VCR Code 533 544 588 776 49 Combo Codes, continued TV/DVD Codes Note: Program the remote control in TV mode using the TV code and then in DVD mode (or in AUXpress 1 before entering the DVD code) using the DVD code. Accurian TV Code 623 AEG TV Code 624 Advent DVD Code 759 Akai TV Code 612 622 624 750 754 807 808 865 866 906 908 DVD Code 515 516 525 646 656 709 725 754 814 815 Apex Digital TV Code 552 DVD Code 635 757 Audiovox TV Code 624 DVD Code 630 Axion TV Code 636 DVD Code 867 Broksonic TV Code 622 754 865 866 908 DVD Code 515 516 525 646 656 709 725 752 754 814 815 Bush TV Code 750 754 DVD Code 634 Citizen TV Code 622 750 754 865 866 908 DVD Code 515 516 525 646 656 709 725 754 814 815 Conia TV Code 743 815 Coby DVD Code 634 636 Curtis TV Code 573 Cytron TV Code 904 DVD Code 904 Denver TV Code 624 Diamond Vision TV Code 643 DVD Code 637 Dynex TV Code 698 701 706 Emerson TV Code 618 643 668 672 764 777 829 838 DVD Code 570 617 619 631 645 658 661 674 679 764 829 ESA TV Code 618 679 777 829 DVD Code 570 631 679 Funai TV Code 618 679 777 829 DVD Code 570 631 679 GFM TV Code 618 679 777 829 DVD Code 570 631 679 Goodmans DVD Code 634 Grundig TV Code 750 754 838 839 838 839 838 839 839 679 Table continued on next page 50 Combo Codes, continued TV/DVD Codes, continued 662 Haier TV Code 693 Hitachi TV Code 786 788 790 791 iLo TV Code 625 Initial TV Code 625 Insignia TV Code 618 671 679 698 751 777 829 838 839 DVD Code 570 631 647 679 Jensen DVD Code 759 JVC TV Code Konka TV Code 510 DVD Code 753 LG TV Code 553 561 766 773 809 Magnavox TV Code 618 625 646 679 767 777 782 829 838 839 DVD Code 570 631 679 Mintek TV Code 625 Mirror DVD Code 634 Panasonic TV Code 644 811 869 DVD Code 663 Polaroid TV Code 534 678 751 DVD Code 635 636 647 677 Prima DVD Code 759 RCA TV Code 503 522 636 637 639 650 671 742 751 763 779 805 831 859 DVD Code 647 867 Samsung TV Code 680 684 DVD Code 740 Sansui TV Code 622 750 865 866 908 DVD Code 515 516 525 646 709 725 775 814 815 Sharp TV Code 546 556 605 898 DVD Code 573 Sylvania TV Code 567 568 618 668 672 679 723 724 764 777 829 838 839 DVD Code 570 617 619 631 645 658 661 674 679 764 829 815 Toshiba TV Code 622 666 750 754 771 793 802 847 848 849 850 851 852 854 855 865 866 908 DVD Code 515 516 525 646 648 656 709 725 754 814 815 Viore TV Code 915 Westinghouse DVD Code 629 51 Combo Codes, continued 779 779 824 899 814 815 DVD/VCR Codes Note: Program the remote control in DVD mode using one of the listed DVD codes, and then in AUX mode, first pressing 1 and then using the listed VCR code. Accurian DVD Code 617 619 658 661 674 764 829 VCR Code 533 544 588 Allegro DVD Code 626 683 VCR Code 502 522 529 678 779 Apex Digital DVD Code 517 851 VCR Code 517 851 Broksonic DVD Code 515 516 525 646 656 709 725 754 VCR Code 511 CineVision DVD Code 626 683 VCR Code 502 522 529 678 779 Daewoo DVD Code 626 683 VCR Code 502 522 529 678 779 Emerson DVD Code 617 619 658 661 674 764 829 VCR Code 519 Funai DVD Code 617 619 658 661 VCR Code 519 GFM DVD Code 617 619 658 661 VCR Code 519 Go Video DVD Code 507 524 611 615 626 673 683 692 691 693 741 820 821 822 824 896 899 VCR Code 502 522 529 678 GoldStar DVD Code 507 611 615 673 VCR Code 502 522 529 678 Hitachi DVD Code 660 706 707 860 VCR Code 533 544 588 JVC DVD Code 622 623 689 VCR Code 503 561 LG DVD Code 507 611 615 673 VCR Code 502 522 529 678 Magnavox DVD Code 617 619 658 661 VCR Code 533 544 588 519 Memorex DVD Code 515 516 525 646 656 709 725 754 814 815 Panasonic DVD Code 624 VCR Code 777 780 Philips DVD Code 617 619 658 661 Polaroid DVD Code 517 851 VCR Code 517 851 52 674 764 829 674 764 829 674 764 829 674 764 829 824 899 779 Combo Codes, continued DVD/VCR Codes, continued 773 774 Presidian DVD Code 617 619 658 661 674 764 829 VCR Code 519 RCA DVD Code 616 690 702 703 720 749 816 842 VCR Code 528 605 607 649 Rio VCR Code 502 522 529 678 779 Samsung DVD Code 524 667 691 693 741 820 821 896 Sansui DVD Code 515 516 525 646 656 709 725 754 VCR Code 515 Sanyo DVD Code 609 659 VCR Code 549 581 Sharp DVD Code 573 669 727 903 VCR Code 573 585 814 815 756 674 764 829 Sony DVD Code 613 618 629 729 730 731 768 778 817 818 847 883 VCR Code 618 768 778 Sylvania DVD Code 617 619 658 661 VCR Code 519 533 544 588 Symphonic DVD Code 617 619 658 661 VCR Code 519 533 544 588 Toshiba DVD Code 575 672 735 736 819 825 828 834 888 VCR Code 672 783 Zenith DVD Code 507 611 615 626 673 683 824 899 VCR Code 502 522 529 678 674 764 829 779 TV/DVD/Tuner Codes Note: Program the remote control in TV mode using the TV code and then in DVD mode and then in AUX mode

(press 2 before entering the tuner code) using the tuner code. Panasonic TV Code 811 DVD Code 734 Tuner Code 678 53 Combo Codes, continued TV/DVD/VCR Codes Note: Program the remote control in TV mode using the TV code and then in DVD mode using the DVD code, and then in AUX mode (press 1 before entering the VCR code) using the VCR code. Akai TV Code 680 684 DVD Code 740 Broksonic TV Code 648 DVD Code 656 752 Diamond Vision TV Code 659 DVD Code 532 641 VCR Code 532 641 Emerson TV Code 646 767 DVD Code 531 570 639 650 651 803 804 ESA TV Code 646 747 DVD Code 531 570 639 650 651 803 804 Insignia TV Code 618 679 777 829 838 839 Funai VCR Code 531 798 Magnavox TV Code 618 646 679 767 777 829 838 839 DVD Code 531 570 639 650 651 803 804 VCR Code 531 798 Memorex TV Code 648 Panasonic TV Code 647 811 860 861 862 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 889 890 895 896 900 DVD Code 638 734 810 813 VCR Code 810 813 Polaroid DVD Code 530 640 VCR Code 530 640 RCA DVD Code 541 775 901 VCR Code 541 775 901 Samsung TV Code 680 684 Sharp DVD Code 573 669 727 903 VCR Code 573 Superscan DVD Code 531 570 639 650 651 803 804 Sylvania TV Code 646 767 DVD Code 531 570 639 650 651 803 804 Symphonic TV Code 646 767 DVD Code 531 570 639 650 651 803 804 Toshiba TV Code 617 DVD Code 893 894 54 Troubleshooting Use this information if you have a problem using the remote. To solve a particular problem, do the following:

Find the information that relates to the problem you are experiencing. Try the suggested solution for that problem. Make sure your remote control has fresh batteries. If you see the Remote Battery Low warning on your TV screen, it is time to change the batteries. Follow the instructions on page 2. Make sure you have a direct line of sight between the remote and the receiver. Visit www.dishnetwork.com. While performing a remote control procedure, the remote control stops working. What to do: Start over again. If you dont press a button for 20-30 seconds in a programming sequence, the remote shuts off its programming function. When you press a button on the remote control, the equipment doesnt do what you expect. What to do: Point the remote control directly at the TV, with no objects blocking the signal path. The remote control uses IR signals to control the receiver. IR signals travel less than 40 feet, and cannot go through walls or other solid objects. If the batteries are missing or dead, replace them with fresh AAA-size batteries. If the remote has fresh batteries, check whether you put them in correctly. If you didnt, take them out and put them in the right way. When you try to enter TV programming mode, all the mode LEDs flash. What to do: Replace the batteries (see page 2). 55 Troubleshooting, continued Your remote control does not work well. What to do: Move your receiver to different locations. For best results, place the receiver as high as possible, above all other equipment in your entertainment center. There may be IR interference from objects near the receiver. Your picture is snowy (or black or blue). What to do: Make sure your TV is tuned to the correct channel. You may have accidentally changed the channel on your TV. Check the Reference Table to see what channel your TV is tuned to. Program SAT Auto-Tune to avoid this in the future (see SAT Auto-

Tune on page 16). When you press the remote control MUTE or VOLUME button, nothing happens. What to do: Program the remote to control your TV. See Programming Remote to Control Another Device on page 11 or page 13. The receiver does things even though you havent pressed any remote control buttons. What to do: See Changing the Remote and Receiver Address on page 28 for instructions to correct the possibility of UHF signals from a neighbors remote controlling your receiver. Your remote control isnt working. What to do: Make sure the remote control is in the correct mode (SAT, TV, DVD, or AUX). Make sure you are using the correct remote control

(TV1 or TV2) for your locations (applicable to multi-

room receivers only). Change the batteries as described on page 2. If you have a 21.1 remote, check the UHF/IR switch setting as described on page 1. 56 Troubleshooting, continued Your UHF Pro remote control does not work well from far away. What to do: Make sure the UHF antenna is connected to the receiver and not touching anything else. Vary the angle of the receivers UHF antenna. Locate the UHF antenna tip away from other electronics equipment or metal surfaces, even if separated by wooden shelving. Move the receiver to different locations. For best results, place the receiver as high as possible, above all other equipment in your entertainment center. Place the UHF antenna outside the entertainment center by using a coaxial cable to connect it to the receiver. Move any nearby off-air antenna away from the UHF remote antenna. Do not place an off-air antenna on your receiver. Your PIP (Picture-In-Picture) button isnt working. What to do: If your receiver isnt in Single Mode, press the MODE button on the front panel (if available). Verify your receiver has the PIP feature. If your receiver is not PIP capable, contact DISH Network about upgrading to a receiver with the PIP feature. 57 Limited Warranty This Limited Warranty is a legal document. Keep it in a safe place. Remember to keep your Sales Receipt for warranty service. We will consider any items you return without a copy of the Proof of Purchase to be out of warranty. This warranty extends only to the original user (you, your) of the DISH Network remote control and is limited to the purchase price of the remote control. EchoStar Technologies L.L.C., formerly known as EchoStar Technologies Corporation, and its affiliated companies (we, our, us) warrant this remote control against defects in materials or workmanship as follows. For one year from the original date of purchase, if we find the remote control is defective subject to the limits of this warranty, we will replace the remote at no charge for parts or labor. We warrant any such work done against defects in materials or workmanship for the remaining part of the original warranty period. This warranty does not cover installation of the DISH Network System;

consumer instruction; physical set up or adjustment of any consumer electronic equipment; remote control batteries; signal reception problems;

loss of use of the equipment; unused programming charges due to equipment malfunction; cosmetic damage; damage due to lightning, electrical or telephone line surges, fire, flood, or other acts of Nature; accident; misuse;

abuse; repair or alteration by other than our factory service; negligence;

commercial or institutional use; improper or neglected maintenance;

equipment sold AS IS or WITH ALL FAULTS; equipment removal or reinstallation; shipping damage if the equipment was not packed and shipped in the manner we prescribe; nor equipment purchased, serviced, or operated outside the contiguous United States of America. REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY. WE SHALL NOT BE HELD LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY ON THIS DEVICE, NOR FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS DEVICE. UNDER NO CIRCUMSTANCES SHALL OUR LIABILITY, IF ANY, EXCEED THE PURCHASE PRICE PAID FOR THIS DEVICE. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS DEVICE IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. WE RESERVE THE RIGHT TO REFUSE TO HONOR THIS WARRANTY IF WE DETERMINE ANY OF THE ABOVE EXCEPTIONS TO HAVE CAUSED THIS DEVICE NOT TO HAVE PERFORMED PROPERLY. THIS WARRANTY SHALL BE VOID IF ANY FACTORY-APPLIED IDENTIFICATION MARK, INCLUDING BUT NOT LIMITED TO SERIAL OR CONDITIONAL ACCESS NUMBERS, HAS BEEN ALTERED OR REMOVED. THIS WARRANTY SHALL ALSO BE VOID IF THE DEVICE HAS BEEN OPENED BY AN UNAUTHORIZED PERSON (with the exception of opening the battery cover). This warranty gives you specific legal rights which may vary from state to state. Some states do not allow the exclusion or limitations of incidental or consequential damages, or allow limitations on the duration of an implied warranty, so those limitations may not apply to you. 58 Accessory Warranty An accessory is any DISH Network branded equipment, displaying the DISH Network logo, excluding the receiver, Smart Card, cables and hookups, and non-mechanical components. A one-

year warranty becomes effective upon the activation of the DISH system or date of purchase, if bought separately. A proof of purchase is required to verify the purchase date. If an accessory has an expired warranty, no exchange will be issued. You may purchase replacement accessories from DISH Network or your local retailer. If You Need Help 1. Review this User Guide. 2. See Troubleshooting on page 55. 3. Visit www.dishnetwork.com/chat for 24/7 support. 4. Call the Customer Service Center at 1-800-333-DISH (3474). 59 Regulatory Factors This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this device may void your authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by following one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. 60 Reference Table Write down your remote address, channel numbers/

inputs, TV, VCR, DVD player, and stereo equipment codes as you program them for future reference. Remote Address Channel or Input for Cable Programming If you enter a 1 as the last number of your code, your remote is in Limited Mode (see page 15 for more details). TV Code

(Optional) VCR/DVD Player Code

(Optional) Auxiliary Equipment Code To read out your remote codes, see page 14 for instructions.

(Optional) 61 For all your customer needs, go to www.dishnetwork.com/chat or call the Customer Service center at 1-800-333-DISH (3474) 180532