FCC ID: MG3-60260 UE878 Standard BLE LGA Module Gen ll

JPN UE878 Standard BLE LGA Module Gen II Part Number: 60260-9000000 Quick Reference Guide PAIRING BLE MODULE (English) 1. Apply Power 3.3V to module 2. Send serial command via UART 3. Module will be in advisement mode Caution Please read these safety instructions to ensure our personal safety and prevent property damage Warning

- Do not put remote in a fire

- Do not disassemble the remote control

- Disposal of the remote control A warning that batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Important Safety Instruction 1. Read these instruction 2. Keep these instruction 3. Head all warning 4. Follow all instructions 5. Do not use this apparatus near water 6. Clean only with dry cloth 7. Do not install near any heat source such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 8. Only use attachment/accessories specified by manufacture 9. Refer all servicing to qualified service personnel. Service is required when apparatus has been damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, dose not operate normally, or has been dropped. Specification Operating Temperature: -10 degree - 40 degree Operating Voltage: 3.3V COMPLIANCE WITH FCC RULES AND REGULATIONS 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase or decrease the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced remote control/ TV technician for help. This equipment has been verified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. FCC RF Radiation Exposure Statement:

To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Authorization Label This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. Warning Statement:

Europe-EU Declaration of Conformity and Restrictions Hereby, SONY declares that this Voice Remote Control is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. This equipment is marked with the symbol and can be used throughout the European community. This indicates compliance with the RE Directive 2014/53/EU and meets the relevant parts of following technical specifications:

EN300328 v2.1.1: 2016 EN301489-1 v2.1.1: 2016 (draft) / -17 v3.1.1: 2016 (draft) EN60065: 2014 EN62479: 2010 EN55032: 2012+AC: 2013; EN55024: 2010+A1: 2015 CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numrique de classe B est conforme la norme NMB-003. RF exposure:

To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Pour se conformer aux exigences de conformit RF canadienne l'exposition, cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. NCC :

La operacin de este equipo est sujeta a las siguientes dos condiciones 1. 2. Es posible que este equipo o dispositivo no cause interferencia perjudicial Este equipo o dispositivo debe aceptar cualquier interferencia. Incluyendo la que pueda causar su operacin no deseada. Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio.

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Connect the equipment into an outlet on a circuit different from that Increase the separation between the equipment and receiver. to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID:

MG3-60260. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com 775 Montague Expressway Milpitas, CA 95035 Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (current) Revision History From 1.0 1.0 2.0 3.0 4.0 To 1.0 2.0 3.0 4.0 5.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 2018-12-13 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Universal Electronics Inc hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s):

UE878 Standard BLE LGA Module Gen ll FCC ID: MG3-60260 Sincerely, YijhenChen Specialist,CertificationCenter BureauVeritasCPS(H.K.)Ltd.,TaoyuanBranch Address:No.19,HwaYa2ndRd.,WenHwaVil.,KweiShanDist, TaoyuanCity33383,TAIWAN(R.O.C.) Tel:+886(0)33183232Ext.1642 EMail:yijhen.chen@tw.bureauveritas.com Web:www.bureauveritasadt.com SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0

Date: November 11, 2018 Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Schematic Diagram Block Diagram Operational Description Subject: Request for Confidentiality FCC ID: MG3-60260 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, External Photos Internal Photos Test Setup Photos Users Manual Jesse Mendez / Staff Engineer, Electrical Universal Electronics Inc Tel: 714-918-9500 Fax: 714-918-4100 E-mail: jmendez@ueic.com 201 East Sandpointe Ave, 8th Floor Santa Ana, California 92707 United States

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com Modular Approval Declaration Letter Reason for Amendment (current / obsolete) Initial Release (Obsolete) Added IC Modular Letter (Obsolete) Add LMA and MA option (Obsolete) Revised per RSS Gen issue 3.0 (Obsolete) Removed Foot(2) (obsolete) Adding New note per KDB996369 D01 V01R03 Updated company template & Added text box

(obsolete)

(current) Revision History From 1.0 1.0 2.0 3.0 4.0 5.0 6.0 To 1.0 2.0 3.0 4.0 5.0 6.0 7.0 Approved Date Dec-04-2006 Feb 16 2009 April 14 2010 Jan 12 2011 July 19 2011 August 29 2011 Jan-31-2012 SCS-F26 Modular Approval Letter Page 1 of 2 Rev 7.0 201 East Sandpointe Ave, 8th Floor, Santa Ana, California 92707, United States Date: November 11, 2018

(UE878 Standard BLE LGA Module Gen II) FCC ID : MG3-60260 , is seeking FCC Authorization as a The EUT meets the requirements for as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below:

Questions are: * Please provide a detailed explanation if the answer is No. Single Modular transmitter /

Single Modular approval /

1. The modular transmitter must have its own RF shielding. Yes /

No 2. The modular transmitter must have buffered modulation/data inputs. Yes /

No 3. The modular transmitter must have its own power supply regulation. Yes /

No Single Limited Modular Approval (Please check one). Single Limited Modular Approval (please check one) 4. The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(c). Yes /

No 5. The modular transmitter must be tested in a stand-alone configuration. Yes /

No 6. The modular transmitter must be labeled with its own FCC ID number. Yes /

No 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate instruction along with the module to explain any such requirements. Yes /

No The modular transmitter must comply with any applicable RF exposure requirements. Yes /

No LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured.

(2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device.

(3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. 8.

(1) Note:

Jesse Mendez/ Staff Engineer, Electrical Universal Electronics Inc. Tel: 714 918-9701 Fax: 714 918-4100 E-mail: jmendez@uei.com SCS-F26 Modular Approval Letter Page 2 of 2 Rev 7.0

%*$$,-./.01. #*)$,)+% #*)$0 !&(

&2$("3$*".

Yijhen Chen Yijhen Chen

#$$*&#)**+*"%*$$,-./.01.

#*)$,)+% #*)$0 !"($4*

56..,&0!*$#$##

$*&2$&$*(&**$73

8*(&*$.

*9"*$!(

%*$$,-./.01. #*)$,)+% #*)$0 !$#.

*#*#4*$""((""#&. Yijhen Chen

58

;585

8"2"9<*.$"