FCC ID: G95OWA0111 Wireless router

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6335252.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case OWA0111 Quick Setup Guide Technicolor Delivery Technologies www.technicolor.com 1. Before you start Carefully read the Safety Instructions and Regulatory Notices document included in your package before continuing with the installation of your OWA0111. Do not make any connections until instructed to do so!

2. Check the content of your box Your package contains the following items:

A B C D Item Description A B C D One OWA0111. User Documentation (this Quick Setup Guide, Safety Instructions &

Regulatory Notices). Other additional documents may be included. One power supply adapter. One Ethernet cable with yellow connectors. 1 3. About the OWA0111 3.1. WiFi WiFi general The OWA0111 is equipped with:

One 5GHz Wi-Fi6 (IEEE802.11ax) interface that provides superior transfer rates and is less sensitive to interference. One 2.4GHz Wi-Fi6 (IEEE802.11ax) interface which allows you to connect Wi-Fi devices that dont support 5GHz Wi-Fi. WiFi6 Enabled with the latest Wi-Fi 6 technology, the OWA0111 offers ultimate wireless networking by improving latency, providing faster throughputs, better performance and optimal link stability in your local network. EasyMesh The OWA0111 supports EasyMesh (as EasyMesh agent) that allows you to bring an ultimate in-home Wi-Fi experience by creating a unified intelligent Wi-Fi environment throughout your home using multiple EasyMesh-enabled access points. 3.2. Top panel WPS WPS button and Status LED (item A) The WPS button on the top panel of your OWA0111 is used to pair the OWA0111 with other Wi-Fi devices and the Status LED on the side of WPS button informs you about the status of your OWA0111. If the Status LED of your OWA0111 is flashing green, your OWA0111 is updating its software. In this case, wait until the LED becomes slowly blinking green. This can take several minutes! Do not power off your gateway or unplug any cables!

2 3.3. Back panel and bottom product label AA DD BBCC Reset button (itemA) When the OWA0111 is powered on and you press the Reset you can restart or reset it. For more information, see 5.8. How to repair an unresponsive Wi-Fi extender on page11. Power button (itemB) The power button allows you to power the OWA0111 on or off. Power port (itemC) The power port allows you to connect the power supply. Warning: Only use the power supply delivered with your OWA0111. Ethernet LAN port (itemD) The Ethernet LAN port allows you to connect an Ethernet device (for example a set-top box, a NAS drive). 4. Set up The OWA0111 can be used:

As a wired Wi-Fi6 home network enabler. You will use this scenario in case your Internet gateway and/or home network has no Wi-Fi, or Wi-Fi capabilities without Wi-Fi6. For this scenario, see 4.1. Wired Wi-Fi6 home network enabler on page4. As a wireless Wi-Fi6 home network enabler. You will use this scenario in case your Internet gateway and/or home network has Wi-Fi, but no Wi-Fi6 and/or EasyMesh. For this scenario, see 4.2. Wireless Wi-Fi6 home network enabler on page5. As an EasyMesh home network extender. 3 You will use this scenario in case you want to extend your existing EasyMesh Wi-Fi home network with additional coverage using the OWA0111. In such environment your Internet gateway or another Wi-Fi device is already operating as the Wi-Fi EasyMesh controller. For this scenario, see 4.3. EasyMesh home network extender on page6. To join an existing EasyMesh home network, you must first enable EasyMesh on your OWA0111 via its GUI. For more information, see 5.7. Configure your Wi-Fi extender to your needs on page10. 4.1. Wired WiFi6 home network enabler This scenario allows you to add Wi-Fi6 coverage using the OWA0111. Wi-Fi 6 Ethernet cable Internet gateway OWA0111 Wi-Fi 6 access point Wi-Fi device You will connect the OWA0111 to your Internet gateway either:

Directly using an Ethernet cable. Indirectly via a powerline adapter or similar. Step 1: Set up the WiFi extender 1 Take the included Ethernet cable (this is the cable with the yellow connectors).

) port Connect one end of the Ethernet cable to the yellow Ethernet LAN (

on the back of your OWA0111. Connect the other end of the Ethernet cable to an Ethernet or LAN port of your Internet gateway. 2 Take the power supply, plug the small end into the power inlet port (

OWA0111 and then plug the other end into a nearby power outlet.

) of the 3 Press the power (

) button on the back of the OWA0111. The Status LED will first be solid yellow during startup, then turns green. If this is not the case, check the connections you made. 4 Wait until the Status LED turns green before connecting your Wi-Fi devices. 4 Step 2: Connect your WiFi devices If your Wi-Fi device:

Supports WPS, use WPS to pair it with the OWA0111. For more information, see 5.4. Pairing Wi-Fi devices to your OWA0111 on page9. Does not support WPS, configure it with the Wi-Fi network name (SSID) and wireless key that are printed on the product label on the bottom of the OWA0111. For more information, consult the user documentation of your device. Step 3: Connect an Ethernet device (optional) You can use the OWA0111s yellow Ethernet LAN (

Ethernet device (for example, a Set-Top Box, a NAS drive or computer) to your home network.

) port to connect an 4.2. Wireless WiFi6 home network enabler This scenario allows you to add (extra) Wi-Fi6 coverage using the OWA0111. Wi-Fi Wi-Fi 6 Internet gateway or Wi-Fi extender OWA0111 Wi-Fi 6 access point Wi-Fi device Step 1: Set up the WiFi extender 1 Position your OWA0111 half-way between your Internet gateway (or extender) and your Wi-Fi devices. 2 Take the power supply, plug the small end into the power inlet port (

OWA0111 and then plug the other end into a nearby power outlet.

) of the 3 Press the power (

) button on the back of the OWA0111. The Status LED will first be solid blue during startup. 4 Wait until the Status LED slowly blinks green. 5 Pair the OWA0111 with your Internet gateway (or extender) using WPS. For detailed instructions, see 5.2. Pairing the OWA0111 with your Internet gateway on page7. 6 Check the link quality via the Status LED on the OWA0111. If it is:

OFF, then link has no CPE connected. ON, then link has CPE connected, but no data activity. Flash, then link has data activity. 5 See 5.6. Optimizing the link quality on page10 for more information. Step 2: Connect your WiFi devices If your Wi-Fi device:

Supports WPS, use WPS to pair it with the OWA0111. For more information, see 5.4. Pairing Wi-Fi devices to your OWA0111 on page9. Does not support WPS, configure it with the Wi-Fi network name (SSID) and wireless key that are printed on the product label on the bottom of the OWA0111. For more information, consult the user documentation of your device. Step 3: Connect an Ethernet device (optional) You can use both of the OWA0111s Ethernet ports to connect Ethernet devices (for example, a Set-Top Box, a NAS drive or computer) to your home network. 4.3. EasyMesh home network extender This scenario allows you to extend Wi-Fi coverage in your home by retransmitting Wi-Fi messages from your existing Wi-Fi EasyMesh network. Wi-Fi 6 EasyMesh Wi-Fi 6 Internet gateway or OWA3111 as EasyMesh controller OWA0111 EasyMesh agent Wi-Fi device Requirements Your Internet gateway or another EasyMesh-capable Wi-Fi device must be enabled and configured as the EasyMesh controller. Step 1: Set up the repeater and onboard to the EasyMesh network 1 Position your OWA0111 half-way between your Internet gateway (or extender) and your Wi-Fi devices. 2 Take the power supply, plug the small end into the power inlet port (

OWA0111 and then plug the other end into a nearby power outlet.

) of the 3 Press the power (

) button on the back of the OWA0111. The Status LED will first be solid blue during startup. 4 Wait until the Status LED slowly blinks green. 5 Enable EasyMesh on your OWA0111 if not done yet. For more information ,see 5.7. Configure your Wi-Fi extender to your needs on page10. 6 6 Onboard the OWA0111 to the EasyMesh network using WPS. For detailed instructions, see 5.3. Joining your OWA0111 with an existing EasyMesh network on page8. 7 Check the link quality via the Status LED on the OWA0111. If it is:

OFF, then link has no CPE connected. ON, then link has CPE connected, but no data activity. Flash, then link has data activity. See 5.6. Optimizing the link quality on page10 for more information. Step 2: Connect your WiFi devices Because the OWA0111 now uses the same Wi-Fi settings as the EasyMesh home network, Wi-Fi devices that were already connected to your home network will also be able to connect to the OWA0111, and vice versa. Step 3: Connect your Ethernet devices (optional) You can use both of the OWA0111s Ethernet ports to connect Ethernet devices (for example, a Set-Top Box, a NAS drive or computer) to your home network. 5. Tips and tricks 5.1. Making a wired connection between the OWA0111 and your Internet gateway 1 Take the included Ethernet cable (this is the cable with the yellow connectors). 2 Connect one end of the Ethernet cable to the yellow Ethernet LAN (

) port on the back of your OWA0111. 3 Connect the other end of the Ethernet cable to an Ethernet or LAN port of your Internet gateway. 5.2. Pairing the OWA0111 with your Internet gateway Requirements Make sure your OWA0111 isnt onboarded already to an existing EasyMesh home network, or paired with another Internet gateway. Procedure 1 Briefly press the WPS (

) button on the OWA0111. The Status LED on the OWA0111 starts blinking green. 7 2 Within two minutes, briefly press the WPS button on your Internet gateway (or a Wi-Fi extender connected to it). Note: On some Internet gateways you may have to press and hold the WPS button for a few seconds or until its WPS LED starts blinking. 3 After some time the Status LED on the OWA0111 turns green. The Wi-Fi connection is now successfully established. Note: If the Status LED is blinking red, go to 5.5. What to do when the Status LED is blinking red? on page9 for further instructions. 4 Check the link quality via the Status LED on the OWA0111. If it is:

OFF, then link has no CPE connected. ON, then link has CPE connected, but no data activity. Flash, then link has data activity. See 5.6. Optimizing the link quality on page10 for more information. 5.3. Joining your OWA0111 with an existing EasyMesh network Requirements Make sure your OWA0111 isnt joined already to an existing EasyMesh home network. Procedure 1 Briefly press the WPS (

) button on the OWA0111. The Status LED on the OWA0111 starts blinking green. 2 Within two minutes, briefly press the WPS button on your Internet gateway or any Wi-Fi extender in the EasyMesh home network. Note: On some Internet gateways you may have to press and hold the WPS button for a few seconds or until its WPS LED starts blinking. 3 During EasyMesh onboarding the Status LED on the OWA0111 goes through

(one or more of) the following states:

Flashing green & yellow (1 second each): EasyMesh onboarding started and ongoing. Flashing green (1 second) & yellow (3 seconds): No EasyMesh network was found. Once the the Wi-Fi connection is successfully established it will turn solid green, yellow or red. Note: If the Status LED is blinking red, go to 5.5. What to do when the Status LED is blinking red? on page9 for further instructions. 8 4 Check the link quality via the Status LED on the OWA0111. If it is:

OFF, then link has no CPE connected. ON, then link has CPE connected, but no data activity. Flash, then link has data activity. See 5.6. Optimizing the link quality on page10 for more information. 5.4. Pairing WiFi devices to your OWA0111 Connecting your WiFi devices using WPS 1 Briefly press the WPS (

) button on WPS the OWA0111. The Status LED on the OWA0111 starts blinking green. 2 Within two minutes, start WPS on your Wi-Fi device. If your Wi-Fi device is:

Another Wi-Fi extender, briefly press its WPS button. Another type of device, consult the documentation of your device. 3 After some time the Status LED on the OWA0111 turns back to its previous solid state (green, yellow or red). The Wi-Fi connection is now successfully established. Note: If the Status LED is blinking red, go to 5.5. What to do when the Status LED is blinking red? on page9 for further instructions. 5.5. What to do when the Status LED is blinking red?

This indicates that the OWA0111 could not establish a Wi-Fi connection through WPS. Do the following:

1 Wait until the red blinking LED goes out, then try using WPS again. 2 Turn your OWA0111 slightly and then try again. 3 Obstructions may deteriorate the signal strength. Try to minimize the number of walls between the two devices and then try again. 4 Move the devices closer to each other and then try again. 9 5.6. Optimizing the link quality Tips To achieve optimal link quality:

Always try to reduce the number of obstacles (especially walls) between your Wi-Fi devices to a minimum. Do not place your Wi-Fi devices in the neighbourhood of devices that cause interfence (microwave ovens, cordless phones, baby monitors, etc.). Use Wi-Fi devices that support and use (multiple) 5GHz Wi-Fi. Status LED If the OWA0111 has a Wi-Fi connection to an Internet gateway, extender or repeater

(with or without EasyMesh), the Status LED will provide information about the quality of the link between them. If the Status LED is:

Solid green: then the link quality is optimal. No further actions are needed. Solid yellow: then the link quality is fair, but not optimal. Change the position of the OWA0111 until the LED turns green. Solid red: then the link quality is bad. Change the position of the OWA0111 until the LED turns green. Repositioning the OWA0111 for better link quality First try to improve the link quality without unplugging the power supply:

1 Reposition the OWA0111 to avoid obstacles, like walls, furniture and TV screens, between the OWA0111 and your access point. 2 Wait 15seconds to allow the OWA0111 to re-evaluate the link quality. If the link quality did not improve:

1 Unplug the power supply and move the OWA0111 closer to your access point, or to a place with less obstacles between the OWA0111 and your access point. 2 Plug in the power supply and wait two minutes to allow the OWA0111 to start up all services and evaluate the link quality. 5.7. Configure your WiFi extender to your needs Accessing the OWA0111 web interface The Wi-Fi extender web interface allows you to configure your Wi-Fi extender using your web browser. To access the Wi-Fi extender web user interface:

10 1 Check the IP address of your OWA0111. If your OWA0111:

Is connected to your home network (either wired or via Wi-Fi), browse to the web interface of your gateway to check the IP address of the OWA0111. Not connected to your home network, the default IP address of the OWA0111 is 192.168.1.2. 2 Browse to the OWA0111s IP address found (or http://192.168.1.2) on a computer or device that is currently connected to your Wi-Fi extender (either wired or over Wi-Fi). 3 The Wi-Fi extender web interface appears. By default, you are logged in as guest. This means that some items are hidden. To view all items, click Sign In and enter admin as user name and the ACCESS KEY printed on the label of your Wi-Fi extender as password. Note: If this is the first time that you sign in, the OWA0111 may offer you to change your password. 4 The Wi-Fi extender web interface appears with all settings available. Configuring Easy Mesh To use EasyMesh you must first enable it on your OWA0111. To enable EasyMesh:

1 Browse to the Wi-Fi extender web user interface and login as the user admin (for more information, see Accessing the OWA0111 web interface on page10). 2 To open the EasyMesh page, click the EasyMesh card header. 3 On the EasyMesh page, you can see whether EasyMesh is enabled on your Wi-Fi extender or not. If the switch is set to:

then the EasyMesh agent is enabled. Clicking the switch will disable EasyMesh on your Wi-Fi extender. then the EasyMesh agent is disabled. Clicking the switch will enable your broadband interface. 5.8. How to repair an unresponsive WiFi extender If at some point your Wi-Fi extender becomes unresponsive you can:

Force it to restart: After restarting the OWA0111 will return to normal operation with its last known working condition and configuration. Reset it to factory defaults: The OWA0111 restarts with the factory default configuration. None of the Wi-Fi and EasyMesh settings, nor other configuration changes you made to the OWA0111 are preserved. Proceed as follows:

1 Make sure that your Wi-Fi extender is turned on. 11 2 Use a pen or an unfolded paperclip to push the recessed Reset button on your Wi-Fi extender:

shortly (1 to 2 seconds) and then release it to force it to restart. for at least 10 seconds and then release it to rest it to factory defaults. Reset 3 Your Wi-Fi extender restarts.. 12 Copyright 2021 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice. DMS3-QIG-25-704v1.2

*6304400A*

6304400A Technicolor Delivery Technologies www.technicolor.com

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6335253.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Symbol SAFETY INSTRUCTIONS AND REGULATORY NOTICES BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ ALL SAFETY INSTRUCTIONS Applicability These Safety Instructions and Regulatory Notices apply to:

Technicolor xDSL Modems & Gateways Technicolor Fiber Modems & Gateways Technicolor LTE Mobile Modems & Gateways Technicolor Hybrid Gateways Technicolor Ethernet Routers & Gateways Technicolor Wi-Fi Extenders Using equipment safely Indication This symbol is intended to alert you of the presence of important operating and maintenance (servicing) instructions in the documentation that is included with your product. This symbol indicates for indoor use only

(IEC 60417-5957).

When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following:

Always install the product as described in the documentation that is included with your product. Do not use this product to report a gas leak in the vicinity of the leak. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Used symbols Following symbols may be found in this and accompanying documentation as well as on the product or accompanying accessories:

Symbol Indication This symbol is intended to alert you that uninsulated voltage within this product may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this product. This symbol indicates Double insulated Class II equipment (IEC 60417-5172). Does not require an earth connection. This symbol indicates Alternating Current (AC). This symbol indicates Direct Current

(DC). This symbol indicates Electrical polarity. This symbol indicates Fuse. Directives Product use You must install and use this product in strict accordance with the manufacturer's instructions as described in the user documentation that is included with your product. Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in the country where you want to use this product. If you have any doubts about the installation, operation or safety of this product, please contact your supplier. Any change or modification made to this product that is not expressly approved by Technicolor will result in the loss of product warranty and may void the user's authority to operate this equipment. Technicolor disclaims all responsibility in the event of use that does not comply with the present instructions. Software and firmware use The firmware in this equipment is protected by copyright law. You may only use the firmware in

*XXXXXXX*

XXXXXXX Technicolor Delivery Technologies 8-10 rue du Renard, 75004 Paris, France technicolor.com Copyright 2022 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice. DMS3-SAF-25-741 v1.0. the equipment in which it is provided. Any reproduction or distribution of this firmware, or any portion of it, without express written consent from Technicolor is prohibited. Software described in this document is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your license agreement. Open Source Software notification The software of this product may contain certain open source software modules which are subject to Open Source Software license terms (see https://opensource.org/osd for definition). Such Open Source Software components and/or versions may change in the future versions of the software product. A list of the Open Source Software used or provided as embedded into the current software of the product and their corresponding licenses and version number are, to the extent required by applicable terms, available on Technicolor's website at the following address:

www.technicolor.com/opensource or at another address as Technicolor may provide from time to time. If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source code of the Open Source Software is available for free upon request. For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the designated Open Source License. Environmental information Batteries (if applicable) Batteries contain hazardous substances which pollute the environment. Do not dispose of them with other articles. Take care to dispose them at special collecting points. Recycle or dispose of batteries in accordance with the battery manufacturers instructions and local/

national disposal and recycling regulations. Energy efficiency Energy savings The user documentation that is included with your product not only provides useful information on all the features of your product, but also on its energy consumption. We strongly encourage you to carefully read this documentation before putting your equipment in service in order to get the best service it can offer you. Safety instructions

Read these instructions. Keep these instructions. Heed all warnings and cautions. Follow all instructions. Climatic conditions This product:

Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 C (104 F); the relative humidity must be between 20 and 80 %. Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation. Must not be exposed to heat trap conditions and must not be subjected to water or condensation. Must be installed in a Pollution Degree 2 environment (an environment where there is no pollution or only dry, non-conductive pollution). If applicable, batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like. This product is intended for indoor use only.

Ventilation and positioning This product is intended to be used indoors in a residential or office environment. Remove all packaging material before applying power to the product. Place and use the product only in positions as described in the user documentation that is included with your product.

In case the product is wall-mountable you can check www.technicolor.com/

ch_regulatory for wall mount instructions. Never push objects through the openings in this product. Do not block or cover any ventilation openings;

never stand it on soft furnishings or carpets. Leave 7 to 10 cm (3 to 4 inches) around the product to ensure that proper ventilation gets to it. Do not install the product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not put anything on it which might spill or drip into it (for example, lighted candles or containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact your supplier or customer service. Wall mounting When the equipment is designed to be wall mount, it must be installed at a height of less than 2m from the finished floor level. Cleaning Unplug this product from the wall socket and disconnect from all other devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Water and moisture Do not use this product near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a warm one may cause condensation on some of its internal parts. Allow it to dry by itself before using the product. Product label For some products, the label with regulatory and safety information can be found on the bottom of the enclosure. Electrical powering The powering of the product must adhere to the power specifications indicated on the marking labels. In case this product is powered by a power supply unit:

For USA: This product is intended to be supplied by a UL listed Direct Plug-in Power Unit marked "Class 2" and rated as indicated on the label on your product. This power supply unit must be Class II and a Limited Power Source in accordance with the requirements of IEC 62368-1/UL 62368-1, Annex Q and rated as indicated on the label on your product. It must be tested and approved to national, or local standards.

Only use the power supply unit that is supplied with this product, is supplied by your service provider or local product supplier, or a replacement power supply unit provided by your service provider or local product supplier. The use of other types of power supplies is prohibited. If you are not sure of the type of power supply needed, consult the user documentation that is included with your product or contact your service provider or local product supplier. Accessibility The plug on the power supply cord or power supply unit serves as disconnect device. Be sure that the mains supply socket outlet you use is easily accessible and located as close to the product as possible. The power connections to the product and the mains supply socket outlet socket must be accessible at all times, so that you always can disconnect the product quickly and safely from the mains supply. Overloading Do not overload mains supply socket outlets and extension power cords as this increases the risk of fire or electric shock. Handling batteries This product may contain disposable batteries.

CAUTION There is danger of explosion if the battery is mishandled or incorrectly replaced. Do not disassemble, crush, puncture, short the external contacts, dispose of in fire, or expose to fire, water or other liquids. Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted. Do not attempt to recharge disposable or non-

reusable batteries. Please follow instructions provided for charging rechargeable batteries. Replace batteries with the same or equivalent type. Do not expose batteries to excessive heat (such as sunlight or fire) and to temperatures above 100 C (212 F). Telephone cable

CAUTION To reduce the risk of fire, use only No 26 AWG wire size or larger telecommunication line cord. Connect the telecommunication line cord only in the PSTN, FXO, DSL or Line port of the product. Never plug the telecommunication line cord in another receptacle of the product. Follow the installation instructions in the sequence as outlined in the user documentation that is included with your product. Servicing

To reduce the risk of electric shock or electrocution, do not disassemble this product. If service or repair work is required, take it to a qualified service dealer. Damage requiring service Unplug this product from the mains supply socket outlet and refer servicing to qualified service personnel under the following conditions:

When the power supply, power cord or its plug are damaged. When the attached cords are damaged or frayed. If liquid has been spilled into the product. If the product has been exposed to rain or water. If the product does not operate normally. If the product has been dropped or damaged in any way. There are noticeable signs of overheating. If the product exhibits a distinct change in performance. If the product is giving off smoke or a burning smell. Protect the product when moving it Always disconnect the power source when moving the product or connecting or disconnecting cables. Interface classifications (upon applicability) The external interfaces of the product are classified as follows:

DSL, Line, PSTN, FXO: Electrical energy source class 2 circuit, on which transients are possible (ES2). Phone, FXS: Electrical energy source class 2 circuit, on which transients are not possible

(ES2). Cable: Electrical energy source class 1 circuit, on which transients are possible (ES1). All other interface ports (e.g. Ethernet, USB,...), including the low voltage power input from the AC mains power supply: Electrical energy source class 1 circuit (ES1).

WARNING The Phone, FXS port will be classified as an ES2 circuit on which transients are possible, when connected internally to the PSTN, FXO port, for example, when the product is powered off. If the product is equipped with a USB interface, or any type of connector with metallic shielding, you are not allowed to connect the Phone, FXS port with the PSTN, FXO or the DSL, Line port by any means, for example with an external telephone cable. Regulatory information North-America - United States of America Federal Communications Commission (FCC) Compliancy statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party - U.S. contact information Technicolor Connected Home LLC, 4855 Peachtree Industrial Blvd., Suite 200, Norcross, GA 30092 USA, 770-212-9009. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Part 15B Suppliers Declaration of Conformity The FCC Part 15B Suppliers Declaration of Conformity (SDoC) for your product is available at the following internet address:

www.technicolor.com/ch_regulatory. FCC radio frequency interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. RF exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in the product documentation. When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 30 cm between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 30 cm from the product and must not lean on the product in case it is wall-mounted. With a separation distance of 30 cm or more, the M(aximum) P(ermissible) E(xposure) limits are well above the potential this wireless interface is capable to produce. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Restricted frequency bands In case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it can only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory. In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. This equipment complies with Part 68 of the FCC Rules. The customer information required for Telephone Terminal Equipment ("TTE") approved for connection to the Public Switched Telephone Network ("PSTN"), pursuant to 47 CFR 68.218(b)(1) is available at the following internet address: www.technicolor.com/ch_regulatory. Restricted use for 6 GHz band In case this product is equipped with a wireless transceiver operating in the 6 GHz band, FCC

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6335229.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6694952.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6694953.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6694954.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6694955.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6694956.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6694958.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case