FCC ID: B32NURIT8000RE4 POINT OF SALE TERMINAL

NURIT 8000 Installation Guide N A . 3 T F A R V I S I O D E R VeriFone Part Number DOC113EN05, Revision A NURIT 8000 Installation Guide 2008 VeriFone, Inc. All rights reserved. No part of the contents of this document may be reproduced or transmitted in any form without the written permission of VeriFone, Inc. The information contained in this document is subject to change without notice. Although VeriFone has attempted to ensure the accuracy of the contents of this document, this document may include errors or omissions. The examples and sample programs are for illustration only and may not be suited for your purpose. You should verify the applicability of any example or sample program before placing the software into productive use. This document, including without limitation the examples and software programs, is supplied As-Is. VeriFone, the VeriFone logo, VeriCentre, Verix, and NURIT are registered trademarks of VeriFone. Other brand names or trademarks associated with VeriFones products and services are trademarks of VeriFone, Inc. All other brand names and trademarks appearing in this manual are the property of their respective holders. Comments? Please e-mail all comments on this document to your local VeriFone Support Team. VeriFone, Inc. 2099 Gateway Place, Suite 600 San Jose, CA, 95110 USA www.verifone.com VeriFone Part Number DOC113EN05, Revision A CONTENTS PREFACE . 5 Audience. 5 Organization . 5 Related Documentation . 5 Guide Conventions. 5 Acronym Definitions . 6 CHAPTER 1 CHAPTER 2 N A . 3 T Overview NURIT 8000 . 8 Features at a Glance . 8 F A R V I S I O R D E Setup Selecting Location . 10 Ease of Use . 10 Environmental Factors . 10 Electrical Considerations . 11 Unpacking Shipping Carton . 12 Examining NURIT 8000 Features . 13 Terminal Front Panel . 13 Terminal Bottom Panel . 14 Using the Magnetic Stripe Card Reader. 14 Using the Smart Card Reader . 15 Using the Printer. 16 Loading Paper into the Printer . 16 Removing the Paper Roll From the Printer . 17 Opening and Closing the Battery/Card Compartment Cover . 18 Connecting the Battery. 19 Connecting and Removing the Battery . 19 Battery Maintenance. 20 Battery Charge Status. 21 Powering On and Off the Terminal With a Battery Pack. 21 Installing SIM, SAM, and SD Cards . 21 Connecting Cables . 24 Data Connection . 24 External Modem Connection. 25 Power Supply . 25 Car Adapter Connection . 27 CHAPTER 3 Specifications Specifications . 28 Model . 28 Power Supply . 28 Printer . 28 Modem . 28 Physical. 28 NURIT 8000 INSTALLATION GUIDE 3 CONTENTS CHAPTER 4 Maintenance and Cleaning CHAPTER 5 Troubleshooting Guidelines Environmental, Regulatory, and Performance Specifications . 28 Temperature and Humidity . 28 User Interactions and Responsibilities . 29 Cleaning the NURIT 8000 . 31 NURIT 8000 Appears to Have No Power . 33 Transactions Cannot be Completed Successfully . 34 Wireless Communication Does Not Work . 34 Operation with Peripheral Device Not Successful . 34 Printer Does Not Print. 34 Printer Continues Printing When Out of Paper. 35 Magnetic Stripe Card Reader Does Not Function Properly . 35 Smart Card Reader Does Not Function Properly . 35 The Keypad Does Not Respond. 35 An Incorrect Response or Data Is Obtained. 35 Tampered Device Displayed On Screen and Keypad Inoperable . 35 N A . 3 T CHAPTER 6 Service and Support Service Returns . 36 Accessories and Documentation . 37 Power Supply . 37 Battery. 38 Cables. 38 External Modem . 38 Documentation . 38 INDEX . 41 R F A R V I S I O D E 4 NURIT 8000 INSTALLATION GUIDE PREFACE Use this guide as the primary source of information for setting up and installing the NURIT 8000. Audience This guide provides a simple description of the NURIT 8000s features as well as basic information for the devices installation and configuration. Organization This guide is organized as follows:

N A . 3 T Chapter 1, Overview. Provides an overview of the NURIT 8000. Chapter 2, Setup. Explains the setup and installation of NURIT 8000, selecting its location, and establishing connections with other devices. Chapter 3, Specifications. Discusses power requirements and dimensions of the NURIT 8000. Chapter 4, Maintenance and Cleaning. Explains maintenance of the NURIT 8000. Chapter 5, Troubleshooting Guidelines. Provides troubleshooting guidelines for problems related to the NURIT 8000s installation and configuration. Chapter 6, Service and Support. Provides information for contacting your local VeriFone service provider and on how to order accessories or documents from VeriFone. F A R V I S I O D To learn more about NURIT 8000, refer to the following set of documents:

NURIT 8000 Quick Installation Guide NURIT 8000 Certifications and Regulations Sheet NURIT 8000 External Modem Quick Installation Guide NURIT 8000 Battery Pack Quick Installation Guide NURIT 8000 Car Adapter Quick Installation Guide VPN VPN DOC113MU01 DOC113MU02 DOC113MU03 E R Related Documentation Guide Conventions Various conventions are used to help you quickly identify special formatting. Table 1 describes these conventions and provides examples of their use. Table 1 Convention Blue Italics Document Conventions Meaning Text in blue indicates terms that are cross references. Italic typeface indicates book titles or emphasis. Example See Guide Conventions. You must not use this unit underwater. NURIT 8000 INSTALLATION GUIDE 5 PREFACE Guide Conventions Table 1 Convention NOTE Document Conventions Meaning The pencil icon is used to highlight important information. Example Box contents, including interconnection cable types, may vary according to specific model. CAUTION The caution symbol indicates hardware or software failure, or loss of data. The unit is not waterproof or dustproof, and is intended for indoor use only. Due to risk of shock do not use the terminal near water. Acronym Definitions Various acronyms are used in place of the full definition. Table 2 presents acronyms and their definitions. The lighting symbol is used as a warning when bodily injury might occur. N A . 3 T Acronym Definitions WARNING F A R V I S I O D E R Table 2 Acronym AC CCC DC ECR LED LCD MII MRA MSAM MSR OS PC PIN POS RAM RJ45 RS232 SAM SDIO SC SD Card SIM Definitions Alternating Current China Compulsory Certificate Direct Current Electronic Cash Register Light Emitting Diode Liquid Crystal Display Ministry of Industry and Information Technology Merchandise Return Authorization Micromodule-size Security Access Module Magnetic Stripe Reader Operating System Personal Computer Personal Identification Number Point-of-Sale Random Access Memory Registered Jack 45 Recommended Standard 232 Security Access Module Secure Digital Iput/Output Smart Card (Integrated Chip Card) Secure Digital Card Subscriber Identity Module 6 NURIT 8000 INSTALLATION GUIDE PREFACE Guide Conventions Table 2 Acronym VPN WiFi Acronym Definitions Definitions VeriFone Part Number Wireless Fidelity N A . 3 T F A R V I S I O D E R NURIT 8000 INSTALLATION GUIDE 7 CHAPTER 1 Overview This chapter provides a brief description of the NURIT 8000. NURIT 8000 The NURIT 8000 Wirless Palmtop Terminal is one of the most advanced, versatile, secure, and convenient POS terminals manufactured today. N A . 3 T F A R V I S I O D E R Features at a Glance Figure 1 The NURIT 8000 Terminal The following is a list of features of the NURIT 8000:

Table 3 Feature LCD Display NURIT 8000 Features Description Graphical LCD display Black and White 128 x 128 pixels Application-dependent touch screen, with stylus 10-key telephone-style keypad 8 function and special keys 18 keys comprised of:

Integrated, front-entry, EMV-compliant smart card reader Integrated, bi-directional magnetic stripe card reader Keypad Smart Card Reader Magnetic Stripe Card Reader NURIT 8000 INSTALLATION GUIDE 8 OVERVIEW Features at a Glance NURIT 8000 Features Table 3 Feature SAM-SD/MMC Cards Compartment SIM Connector Thermal Printer Description Compartment for up to two SAM cards Compartment for up to one SD/MMC card Note: Configuration is model-dependent. Connector for the insertion of a SIM card (model dependent) Integrated printer uses thermal paper Easy-load mechanism Barrel power ( POWER) connector Data connector N A . 3 T Internal antenna, located under paper roll, with power supply GSM Note: Configuration is model-dependent. AC/DC adapter (safety approved) Output: 9-10 V at 1 A Note: The AC/DC adapter must be approved by the relevant authorities in the country where the equipment is sold. Ported NURIT for maximum application portability Car adapter External modem Terminal Interface Connector Radio Power F A R V I S I O Operating System Accessories D E R NURIT 8000 INSTALLATION GUIDE 9 Setup CHAPTER 2 This chapter describes the setup procedure for NURIT 8000, in the following sections:

Selecting Location Unpacking Shipping Carton Examining NURIT 8000 Features Using the Magnetic Stripe Card Reader Using the Smart Card Reader Using the Printer Opening and Closing the Battery/Card Compartment Cover Connecting the Battery Connecting Cables Power Supply F A R V I S I O N A . 3 T Installing SIM, SAM, and SD Cards D Use the following guidelines to select a location for the NURIT 8000. E R Selecting Location Ease of Use When not operated from its hand-held position, place the NURIT 8000 on a flat table or countertop close to the power outlet and any peripherals. Maintain good ventilation. Environmental Factors Do not use the unit where there is high heat, dust, humidity, moisture, or caustic chemicals or oils. Do not use the NURIT 8000 in a known blasting area. Do not use the NURIT 8000 in an area of potential explosive atmosphere, such as fuel or chemical storage or transfer facilities, or in any area where you would be advised to turn off a vehicles engine. Do not cover slots and openings of the device. They may be provided for ventilation and protection against overheating. Never place the device near radiators, or in a place where proper ventilation is not provided. Do not cover the terminal. NURIT 8000 INSTALLATION GUIDE 10 SETUP Selecting Location CAUTION Maintain at least 22 cm (8.5 in) of clear space around the terminal in its fixed operating location, in order to assure good ventilation. Indoor Use The NURIT 8000 is designed to be operated indoors in the following manner:

Powered only by the built-in battery. Using the AC/DC power adapter for battery charging only. Using the optional external modem. Outdoor Use The NURIT 8000 is designed to be operated outdoors in the following manner:

Powered only by the built-in battery. In a vehicle, using the optional car adapter. Under no circumstances should the NURIT 8000 be powered or charged outdoors using its AC/DC adapter. N A . 3 T F A R V I S I O D WARNING For persons using a pacemaker or other medical device, please read the E R following important safety notes:

Though most electronic equipment and critical medical devices are shielded against radio-frequency signals, it is important to realize the possibilities of potential interference and to know the standard precautions that may be taken. Consult the manufacturer of your medical device to determine its level of shielding. NOTE When the NURIT 8000 terminal is used as a secure PIN entry device:

The customer should be able to obstruct visual observation of the PIN entry with his/her body and hand. The cardholder must be clearly instructed to obstruct visual observation of the PIN entry with his/her body and hand. Failure to comply with these conditions may render the PIN pad non-compliant with ISO 9564 for PIN protection and may violate card association requirements for PIN entry devices. Electrical Considerations Avoid using this product during electrical storms. Avoid locations near electrical appliances or other devices that cause excessive voltage fluctuations or emit electrical noise (for example, air conditioners, electric motors, neon signs, high-frequency or magnetic security devices, or computer equipment). NURIT 8000 INSTALLATION GUIDE 11 SETUP Unpacking Shipping Carton Do not use the NURIT 8000 near water or in moist conditions. Never spill any liquid on the device. Never push objects into the device through slots (other than those specifically intended for the magnetic stripe, smart cards, SAM cards, or cable ports). To reduce the risk of shock, do not disassemble any of the equipment or accessories referred to in this manual. If required, take the equipment to a qualified service representative. Incorrect reassembly or opening or removing covers may expose you to dangerous voltages or other risks. WARNING Due to risk of shock or damage, do not use the NURIT 8000 near water, including a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Open the shipping carton and carefully inspect its contents for possible tampering or shipping damage. The NURIT 8000 is a secure product and any tampering can cause it to cease to function or to operate in an unsecured manner. 1 Remove and inspect the contents of the shipping carton. The NURIT 8000 N A . 3 T F A R V I S I O Unpacking Shipping Carton To unpack the shipping carton D E R carton includes the following components:

NURIT 8000 terminal AC/DC power adapter Documentation Touch screen stylus Thermal paper roll Paper roll spindle RS-232 barcode reader adapter (model dependent) Keyboard emulation barcode reader adapter (model dependent) PC-Terminal cable (model dependent) Terminal-terminal cable (model dependent) Lithium-polymer Battery 2 Remove all plastic wrapping from the components. 3 Remove the clear protective film from the LCD screen. 4 Save the shipping carton and packing material for future repacking or moving of the device. WARNING Do not use a unit that has been tampered or damaged. The NURIT 8000 comes equipped with tamper-evident labels. If a label or component appears damaged, please notify the shipping company and your VeriFone service provider immediately. 12 NURIT 8000 INSTALLATION GUIDE SETUP Examining NURIT 8000 Features NOTE The package contents, including interconnection cable types, may vary according to the specific model. Some or all of the accessories contained in the box may already be installed in the PIN pad. Examining NURIT 8000 Features Before you continue with the installation process, familiarize yourself with the NURIT 8000 features:

PAPER COVER E R Terminal Front Panel STYLUS PAPER TEAR BAR MAGNETIC STRIPE CARD SLOT Figure 2 NURIT 8000 Terminal Features (Front Panel) N A . 3 T SMART CARD SLOT LCD SCREEN KEYPAD F A R V I S I O D COMPLIANCE LABEL MODEL/SERIAL NUMBER BATTERY/CARD COMPARTMENT COVER DATA CONNECTOR POWER CONNECTOR Figure 3 NURIT 8000 Terminal Features (Bottom Panel) The front panel of the NURIT 8000 terminal (see Figure 2) includes the following features:

A touch screen terminal display, backlit LCD screen. A stylus, with an integrated stylus storage slot. An 18-key, telephone-style keypad. A magnetic card reader on the top of the terminal. Bi-directional swiping capabilities. Swipe the card with the magnetic stripe down and left, towards the terminal and the keypad. For further directions, see Using the Magnetic Stripe Card Reader. NURIT 8000 INSTALLATION GUIDE 13 SETUP Using the Magnetic Stripe Card Reader Terminal Bottom Panel A smart card reader, built into the front of the terminal. For further directions, see Using the Smart Card Reader. A thermal printer. The bottom panel of the NURIT 8000 terminal (see Figure 3) includes the following features:

An interconnection port panel. The interconnection port panel includes the following ports:

A Power Socket where the power cable is plugged. For directions on connecting the terminal to an electrical outlet, see Power Supply. A Data connector. For directions on connecting to the data port, see For information on ordering an external modem for the NURIT 8000 terminal, see Accessories and Documentation.. A battery pack/card compartment with removable door. The card compartment is where the optional SIM (subscriber identity module), SAM

(security access module), and SD (secure digital) cards are installed

(configuration is model dependent). N A . 3 T For directions on installing and removing the battery pack/card compartment door, see Opening and Closing the Battery/Card Compartment Cover. F A R V I S I O For directions on installing and removing the battery pack, see Connecting the Battery. For directions on installing and removing the SIM, SAM, and SD cards, see Installing SIM, SAM, and SD Cards. VeriFone ships variants of the NURIT 8000 terminal for different markets. Your terminal may have a different configuration. The following devices may or may not be present: a smart card reader, up to four MSAM cardholders, or a battery pack. However, the basic processes described in this guide remain the same, regardless of terminal configuration. The magnetic stripe card reader is located at the top end of the NURIT 8000 terminal. Use the magnetic stripe card reader with a magnetic stripe card. 1 Hold the card with the magnetic stripe positioned down and facing towards the LCD display. Insert the card into one end of the card reader slot. 2 D R E NOTE Using the Magnetic Stripe Card Reader To use the magnetic stripe card reader 14 NURIT 8000 INSTALLATION GUIDE SETUP Using the Smart Card Reader NOTE Using the Smart Card Reader To use the smart card reader 2 E R 3 Swipe the card in a smooth, continuous movement, all the way through the slot. Figure 4 Swiping Magnetic Card For guidance, a pictogram near the card slot indicates how to swipe the magnetic stripe card in the card reader. The magnetic stripe card reader supports bi-directional swiping of cards. The EMV-compatible smart card reader is located at the bottom end of the NURIT 8000 terminal. Use the smart card reader with a smart card. N A . 3 T 1 Hold the smart card horizontally, with the metal chip facing up and at the edge F A R V I S I O D of the card nearest to the smart card reader slot. Insert the card into the smart card reader slot. Figure 5 3 Remove the card when prompted by the POS terminal, depending on the Inserting Smart Card specific application being used. NOTE For guidance, a pictogram near the card slot indicates how to insert the smart card into the smart card reader. In addition, insertion direction arrows may be engraved or inscribed on the smart card. NURIT 8000 INSTALLATION GUIDE 15 SETUP Using the Printer Using the Printer An integrated thermal printer is built into the NURIT 8000. Before you can process transactions in the NURIT 8000 that require a receipt or record, you must install paper in the printer. Before using the printer, load a roll of paper into the printer. Loading Paper into the Printer To load paper into the printer D E R 1 2 3 Place the terminal on a flat, stable surface. Insert two fingers into the recess on the paper compartment cover, beneath the release latch. Pull the opening latch up until the cover unlocks. N A . 3 T F A R V I S I O Figure 6 Opening the Paper Compartment 4 Remove the tape strip from a new paper roll. 5 Unroll approximately 5 cm (2 in) of paper to facilitate the loading process. 6 Hold the paper roll with the unrolled end on the underside. 7 Lower the paper roll into the paper compartment. Figure 7 8 Inserting a Paper Roll Pull the unrolled end of the paper approximately 2.5 cm (1 in) out of the paper compartment, ensuring that the paper feeds from the underside of the roll. 9 Make sure that the opening latch is down, in its original position. 16 NURIT 8000 INSTALLATION GUIDE SETUP Using the Printer Removing the Paper Roll From the Printer To remove a roll of thermal paper from the printer E R 10 Close the paper compartment cover, pressing down firmly, until it snaps into place. N A . 3 T Figure 8 Closing the Paper Compartment When a roll of paper is finished, or if the paper is jammed, you may have to remove the old roll in order to replace it. F A R V I S I O 1 2 D 3 4 5 Place the terminal on a flat, stable surface. Insert two fingers into the recess on the paper compartment cover, beneath the release latch. Pull the opening latch up until the cover unlocks. Lift the paper compartment cover until it is fully open (see Figure 6). Lift the paper roll out of the paper compartment. Figure 9 Removing the Paper Roll NURIT 8000 INSTALLATION GUIDE 17 SETUP Opening and Closing the Battery/Card Compartment Cover Opening and Closing the Battery/Card Compartment Cover NOTE To remove the battery

/card compartment cover D E R To access the battery/card compartment, you have to first remove the compartment cover. SIM, SAM, and SD card configurations are model dependent. 1 Disconnect the AC/DC power adapter from the electrical power outlet. 2 Carefully place the NURIT 8000 face down on a soft, smooth surface, so as not to damage the LCD screen. Secure the unit with one hand. 3 4 With your other hand, release the battery /card compartment cover by N A . 3 T pressing and lifting its locking tab. Lift the cover and detach it from the terminal. F A R V I S I O 5 Figure 10 Removing the Battery/Card Compartment Cover To replace the battery pack/card compartment cover 1 Place the NURIT 8000 face down on a soft, smooth surface, so as not to damage the LCD screen. Figure 11 2 Replacing the Battery/Card Compartment Cover Insert the two hinges of the battery/card compartment cover into the hinge slots on the edge of the battery/card compartment. 3 Close the compartment cover and press down until the locking tab snaps into place. 18 NURIT 8000 INSTALLATION GUIDE SETUP Connecting the Battery 4 Connect the AC/DC power adapter from the electrical power outlet. Connecting the Battery The NURIT 8000 terminal comes with a Lithium-polymer battery. Read this section to know how to install and remove the battery. NOTE Only use batteries provided by VeriFone. For information about purchasing additional or replacement batteries, see Accessories and Documentation. Connecting and Removing the Battery Depending on your model of the NURIT 8000 terminal, the battery compartment may be shared with the SIM, SAM, and SD cards. To gain access to the battery/

card compartment, you must first remove the battery/card compartment door. For information on removing and replacing the battery/card compartment cover, see Opening and Closing the Battery/Card Compartment Cover. The NURIT 8000 allows you to operate the terminal without an external power supply, by using a battery. N A . 3 T F A R V I S I O D 2 Hold the battery, verifying that the side with the metal contacts are facing downwards and that the rounded edge is facing towards the back of the compartment. 3 While holding the battery at a 30 angle, slide the two tabs on the front of the battery into the slots on the front wall of the compartment. Push the back of the battery down, until it snaps into place. 4 E R To insert the battery 1 Remove the battery/card compartment cover. See Figure 10. Figure 12 5 Replace the battery/card compartment cover. See Figure 11. Inserting the Battery To remove the battery 1 Power off the terminal. See Powering On and Off the Terminal With a Battery Pack. 2 Remove the battery/card compartment cover. See Figure 10. 3 Insert your fingernail into the groove at the back of the battery and lift the battery, snapping the battery out of place. NURIT 8000 INSTALLATION GUIDE 19 SETUP Connecting the Battery 4 Lift and remove the battery. Figure 13 5 Replace the battery/card compartment cover. See Figure 10. Removing the Battery Battery Maintenance CAUTION D E CAUTION R F A R V I S I O N A . 3 T Take care when installing the battery pack. If it is installed incorrectly, it may explode. Use only a VeriFone supplied battery. The supplied high-performance smart Lithium-polymer battery provides 7.4 VDC at 1800 mAH (minimum) capacity. When fully discharged, the battery fully recharges within three hours while installed in the terminal. An 80% charge capacity is reached within one hour. The terminal can be connected to an AC/DC power supply indefinitely without causing damage to the battery pack. When using the VeriFone-supplied AC/DC power adapter, the Lithium-polymer battery must be installed in the terminal. In typical use, the life span of the battery exceeds 500 charge cycles, after which, operating time decreases slowly. The battery pack has a self-discharge rate. It loses approximately 1% of its charge per day when not in use. Replace the battery pack when the charge capacity is too weak for normal operation. Remove the battery pack from the terminal if you do not intend to use your NURIT 8000 for an extended period of time. WARNING Do not break open, or separate the battery. WARNING Do not dispose of the NURIT 8000 Lithium-polymer smart battery in a fire. LIthium-polymer batteries must be recycled or disposed of properly. Do not dispose of Lithium-polymer batteries in municipal waste sites. 20 NURIT 8000 INSTALLATION GUIDE SETUP Installing SIM, SAM, and SD Cards NOTE Extreme temperatures degrade the battery pack performance. Battery Environmental Requirements:

Standard Charge: 0C to 40C (32F to 104F) Discharge: -20C to 50C (-4F to 122F) Storage: -20C to 60C (-4F to 140F) Battery Charge Status Powering On and Off the Terminal With a Battery Pack E NOTE R Installing SIM, SAM, and SD Cards Battery Charge LED Indicator Status The LED indicator on the car adapter lights according to the charge status. Table 4 Indicator Red Green No light Charge Status The battery is charging (less than 80% charged) The battery is charging (80% or more charged) the battery is fully charged or the charger is disconnected from the power outlet. To power on a terminal, while using a battery pack, press the ON/OFF button, on the keypad. Hold down the button until the terminal powers up. To power off a terminal, while using a battery pack, press down on both the function (F) and ON/OFF buttons, simultaneously. Hold down the button until the terminal powers down. N A . 3 T F A R V I S I O D Powering off the terminal is only possible when the terminal is running on batteries, and not connected to an AC power supply. Configuration of SIM, SAM, and SD cards are model dependent. You can install one SIM card, up to two SAM cards, and an SD card in the NURIT 8000 terminal, depending on the particular model. The card compartment is shared with the battery. To gain access to the battery/

card compartment, you must first remove the battery/card compartment door. For information on removing and replacing the battery/card compartment door, see Opening and Closing the Battery/Card Compartment Cover. NOTE A SIM card must be installed when using a model of the NURIT 8000 that implements GSM or GPRS wireless communications technology. NURIT 8000 INSTALLATION GUIDE 21 SETUP Installing SIM, SAM, and SD Cards To install a SIM or a SAM card NOTE 1 Remove the battery/card compartment door. See Figure 10. 2 3 If necessary, remove the battery. See Figure 13. Slide the locking-clasp in the direction indicated by the engraved arrow to the OPEN position. Lift the cardholder on its hinge to a vertical position. 4 5 Hold the SIM/SAM card vertically, with the beveled corner at the top edge and the metallic contacts facing towards the contacts on the reader. Slide the card into the cardholder. 6 Make sure that you first slide the end closest to the chip on the card into the grooves of the holder and that the beveled corner is on the top edge of the SAM card. N A . 3 T Lower the SIM/SAM cardholder onto its base. Check that the corner of the SIM/SAM card is not obstructed by the triangular protrusion at the corner of the cardholder base. Lock the SAM cardholder by sliding the cardholder locking clasp to the LOCK position. 7 F A R V I S I O 8 Do not bend or scratch the contacts of the SAM cardholder when installing or removing cards. If necessary, replace the battery. See Figure 12. 9 10 Replace the battery/card compartment cover. See Figure 11. D E CAUTION R Figure 14 Installing and Removing a SIM/SAM Card To remove a SIM/SAM card 1 Open the card holder, by following steps 1-4 of To install a SIM or a SAM card and remove the card. 2 Close the card holder by following steps 7-8 of To install a SIM or a SAM card. 22 NURIT 8000 INSTALLATION GUIDE SETUP Installing SIM, SAM, and SD Cards For further instructions, see Figure 14. To install an SD/MMC card E Inserting the SD/MMC Card Figure 15 6 7 Replace the battery/card compartment cover. See Figure 11. If necessary, replace the battery. See Figure 12. R To remove an SD/

MMC Card If necessary, remove the battery. See Figure 13. 1 Remove the battery/card compartment door. See Figure 10. 2 3 Hold the SD/MMC card directly above the SD/MMC card slot, with the metal contacts facing down and the narrow edge with the beveled corner pointing towards the slot opening. Lower the SD/MMC card into position. Press down on the SD/MMC card while sliding it into the slot, until the card snaps into place. 4 5 D F A R V I S I O N A . 3 T 1 Remove the battery/card compartment door. See Figure 10. 2 3 With one hand press down on the SD/MMC locking tab, while sliding the card If necessary, remove the battery. See Figure 13. out with your other hand. 4 Remove the SD/MMC card. Figure 16 5 Removing the SD/MMC Card If necessary, replace the battery. See Figure 12. NURIT 8000 INSTALLATION GUIDE 23 SETUP Connecting Cables 6 Replace the battery/card compartment cover. See Figure 11. Connecting Cables The NURIT 8000 has the following ports to facilitate different types of cabling connections:

For information on ordering an external modem for the NURIT 8000 terminal, see Accessories and Documentation. Power Supply POWER CONNECTOR DATA CONNECTOR NURIT 8000 Connections N A . 3 T Data Connection The data cable is an accessory which may be ordered separately. For information on ordering an external modem for the NURIT 8000 terminal, see Accessories and Documentation. CAUTION Turn off the POS terminal, and any peripheral devices whenever you connect or disconnect the NURIT 8000. Do not disconnect the NURIT 8000 from an external device when it is processing data. Figure 17 F A R V I S I O D Peripheral devices may require special adapter cables for their connection to the NURIT 8000. In addition, certain peripheral devices require an external power supply. Refer to the product documentation of the specific peripheral devices, or contact your local VeriFone representative or service provider for further details. 1 2 3 4 Turn off the external device to which the base unit is to be connected and/or the NURIT 8000 terminal. Insert the plug into the data port on bottom of the unit. Insert the plug at the other end, into the external device. Turn on the external device and/or the NURIT 8000 terminal. NOTE E R To connect the data cable Figure 18 Possible Data Connections 24 NURIT 8000 INSTALLATION GUIDE SETUP Power Supply To remove the data cable 1 Turn off the external device to which the base unit is connected and/or the NURIT 8000 terminal. 2 Detach the plug from the external device. 3 Detach the plug from the data port on the bottom of the terminal. 4 Turn on the NURIT 8000 terminal. The External Modem is an optional accessory that has model dependent connection capabilities. You can use the high-speed modem to download applications and parameters to the NURIT 8000 via a standard telephone line. For more information, see Features at a Glance. For information on ordering an external modem for the NURIT 8000 terminal, see Accessories and Documentation. 1 Connect the modems data plug into the data port on the front panel of the 2 Connect a standard telephone line cord from the modem to a standard RJ-11 type modular telephone line outlet. N A . 3 T NURIT 8000 terminal. F A R V I S I O D External Modem Connection To connect the external modem E R Figure 19 External Modem Connection To disconnect the external modem 1 Disconnect the modems data plug from the data port on the front panel of the NURIT 8000 terminal. 2 Disconnect the standard telephone line from the telephone outlet. CAUTION Do not disconnect the NURIT 8000 from an external device when it is processing data. Power Supply The NURIT 8000 gives you the option of running the unit on battery power, or through a power adapter. The power adapter both gives power, as well as recharges the battery. For information on using the battery, see Connecting the Battery. Before connecting a power supply, disconnect the power cord from the power outlet. NURIT 8000 INSTALLATION GUIDE 25 SETUP Power Supply Connect and route all cables between the NURIT 8000, ECR, and PC before plugging the power pack cord into a wall outlet or surge protector. WARNING Use only the VeriFone supplied AC/DC power adapter to power the NURIT 8000. The power adapter provides electrical power to the NURIT 8000 as follows:

AC/DC adapter (safety approved) Output: 9-10 V at 1 A WARNING Do not plug the power pack into an outdoor outlet or operate the NURIT 8000 outdoors. Also, disconnecting power during a transaction can cause transaction data files not yet stored in memory to be lost. To protect against possible damage caused by lightning strikes and electrical surges, VeriFone recommends installing a power surge protector. Connect one end of the power adapter cable to the Power port on the bottom of the terminal and the other into an electrical power outlet. N A . 3 T F A R V I S I O NOTE D E R Figure 20 Power Supply Connection 26 NURIT 8000 INSTALLATION GUIDE SETUP Power Supply Car Adapter Connection The car adapter is an optional accessory. You can use the car adapter to provide power to the NURIT 8000 and to charge the installed Lithium-polymer battery. For information on ordering a car adapter for the NURIT 8000 terminal, see Accessories and Documentation. To connect the car adapter Connect one end of the car adapter cable to the Power port on the back of the terminal and the other into the vehicles electrical power socket. N A . 3 T Figure 21 Car Adapter Power Supply Connection The LED indicator on the car adaptor indicates the charge status of the battery, as described in Battery Charge Status. F A R V I S I O D E NOTE R To remove the car adapter Unplug the car adapter from the vehicles electrical power socket and then from the power connector, at the front of the NURIT 8000 terminal. NURIT 8000 INSTALLATION GUIDE 27 CHAPTER 3 Specifications This chapter discusses power requirements, dimensions, and other specifications of the NURIT 8000. Specifications The following specifications describe the NURIT 8000 physical and electrical The AC/DC adapter must be compliant with the applicable standards and/or approved by the relevant authorities in the country where the equipment is sold. Power Supply AC/DC adapter (safety approved) N A . 3 T characteristics. Model NURIT 8020 Output: 9-10 V at 1 A F A R V I S I O D E Printer Thermal; easy-load mechanism. Modem Optional accessory. R Choice of three speeds: 14.4 Kbps, 33.6 Kbps, or 56 Kbps telephone line modem

(model dependent). Implements synchronous or asynchronous, HDLC, TCP/IP protocols. Supports Fast Connect connectivity. May be supplied with the terminal as a standard accessory (model dependent). Physical Length: 210 mm (8.27 in.). Width: 92 mm (3.62 in.). Height: 59 mm (2.32 in.). Weight: terminal, 625 g (22.05 oz.); full shipping, 800 g (28.2 oz.). Environmental, Regulatory, and Performance Specifications The NURIT 8000 meets all the necessary environmental, regulatory, and performance standards for its intended use and expected market. VeriFone recognizes its responsibility to minimize the environmental impacts of its operations and products. This device is not intended for outdoor use and is certified for indoor use only. Temperature and Humidity Operating Temperature and Humidity Temperature: 0oC to +40oC (+32oF to +113oF) Humidity: 5-95% RH, non-condensing NURIT 8000 INSTALLATION GUIDE 28 SPECIFICATIONS Environmental, Regulatory, and Performance Specifications Storage Temperature and Humidity Temperature: -20oC to +60oC (-4oF to +140oF) Humidity: 5-95% RH, non-condensing User Interactions and Responsibilities Reference: IEEE 1725, Section 9.2 Do not disassemble or open crush, bend or deform, puncture or shred Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, expose to fire, explosion or other hazard. Only use the battery for the system for which it is specified Only use the battery with a charging system that has been qualified with the system per this standard. Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard. Do not short circuit a battery or allow metallic conductive objects to contact N A . 3 T Replace the battery only with another battery that has been qualified with the system per this standard, IEEE-Std-1725-200x. Use of an unqualified battery may present a risk of fire, explosion, leakage or other hazard. battery terminals. F A R V I S I O D E R Promptly dispose of used batteries in accordance with local regulations Battery usage by children should be supervised. Avoid dropping the phone or battery. If the phone or battery is dropped, especially on a hard surface, and the user suspects damage, take it to a service center for inspection. Improper battery use may result in a fire, explosion or other hazard. NURIT 8000 INSTALLATION GUIDE 29 SPECIFICATIONS Environmental, Regulatory, and Performance Specifications WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. N A . 3 T Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. receiver is connected. F A R V I S I O D E R 30 NURIT 8000 INSTALLATION GUIDE CHAPTER 4 Maintenance and Cleaning The NURIT 8000 has no user-serviceable parts. CAUTION Opening or disassembling the terminal in any way automatically erase all secret encryption keys and will render the PIN pad inoperable. Cleaning the NURIT 8000 To clean the NURIT 8000 R Opening the terminal will void any warranty and security certification. It may also result in irreversible damage to the units electronic circuitry. In order to maintain the NURIT 8000 in proper working condition:

Keep the terminal dry and in the cleanest possible working and storage N A . 3 T Do not store the terminal in extremely hot or cold areas. Do not shake or drop the terminal. Disconnect the device from the power supply and any peripherals before cleaning. environment. F A R V I S I O D E Gently wipe off dirt from the body of the terminal with a soft, damp, lint-free cloth. A very mild dishwashing detergent can be used to dampen the cloth. If available, a low-pressured blower can be used to remove dirt accumulated around the keypad buttons. Use a soft cloth, an eyeglass lens wiper, or a lens blower to remove dust and dirt from the LCD screen. NURIT 8000 INSTALLATION GUIDE 31 MAINTENANCE AND CLEANING Cleaning the NURIT 8000 To clean the PIN pad, use a soft, damp, lint-free cloth slightly dampened with water and a drop or two of mild soap. For stubborn stains, use alcohol or an alcohol-based cleaner. For best results, use a VeriFone Cleaning Kit (refer to the Accessories and Documentation section). CAUTION Never use abrasive compounds or solvents, thinner, trichloroethylene, ketone-

To clean the printer 1 Disconnect the terminal from the power supply. based solvents, benzene, or synthetic cleansers they can deteriorate plastic or rubber parts. Do not spray cleaners or other solutions directly onto the keypad or display. Never clean the unit with liquids. Use only a lightly dampened cloth or soft brush. Never rub or strongly press on the LCD display. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning and/or a soft brush. 2 Open the paper roll compartment cover. See Figure 6. 3 Carefully lift the paper roll (See Figure 9) and remove any excess pieces of paper or dirt that might be lodged in the compartment. If available, use a low-

pressure compressed air gun. 4 Replace the paper roll. See Figure 7. 5 Close the paper roll compartment cover. See Figure 8. N A . 3 T F A R V I S I O D E R 32 NURIT 8000 INSTALLATION GUIDE Troubleshooting Guidelines CHAPTER 5 The troubleshooting guidelines provided in the following section are included to assist you to successfully install and configure your NURIT 8000 device. If you have problems operating your NURIT 8000 device, please read through these troubleshooting examples. If the problem persists even after performing the outlined guidelines or if the problem is not described below, contact your local VeriFone representative for assistance. Typical examples of malfunction you may encounter while operating your NURIT 8000 device and steps you can take to resolve them are listed. D The NURIT 8000 comes equipped with tamper-evident labels. The device contains no user serviceable parts. Do not, under any circumstance, attempt to disassemble the device. Perform only those adjustments or repairs specified in this guide. For all other services, contact your local VeriFone service provider. Service conducted by parties other than authorized VeriFone representatives may void warranty. N A . 3 T F A R V I S I O CAUTION Use only a VeriFone-supplied power cord. Using an incorrectly rated power supply may damage the device or cause it not to work as specified. Before troubleshooting, ensure that the power supply matches the requirements specified at the bottom of the device. (See Chapter 3, Specifications for detailed power supply specifications.) Obtain the appropriately rated power supply before continuing with troubleshooting. NOTE E R NURIT 8000 Appears to Have No Power If the NURIT 8000 appears to have no power:

Check all cable connections. Check that the voltage is reaching the AC power outlet by connecting a different device to this outlet. If you suspect any type of problem at this electric outlet, contact a certified electrician for a professional inspection. Check that the AC/DC power adapter is correctly connected to the power supply, as described in Power Supply. Try adjusting the LCD screen contrast settings, using the designated, model-

dependent, key combination. Press and hold down on the ON/OFF key for three (3) seconds. Check that the battery is securely installed and sufficiently charged, as described in Connecting the Battery. NURIT 8000 INSTALLATION GUIDE 33 TROUBLESHOOTING GUIDELINES Transactions Cannot be Completed Successfully If possible, try to operate the NURIT 8000 with a different VeriFone supplied AC/DC power adapter. Connect the NURIT 8000 to a different AC power outlet. If the problem persists, contact your VeriFone distributor or service provider. If transactions cannot be completed successfully:

Try to perform the transaction using a different magnetic stripe card or smart card (model dependent). F A R V I S I O Make sure that you insert or swipe the card in the proper manner. Attempt to complete several transactions manually using the terminals keypad instead of using customer cards. If all these transactions are completed successfully, contact an authorized representative or service provider. If manually performed transaction is not completed successfully, verify that the wireless transmission quality is sufficient to complete the transaction. Try changing your location to obtain improved transmission quality. If the problem persists, contact your VeriFone distributor or service provider. N A . 3 T If the wireless communication is disrupted or cannot be established:

Try moving the terminal to a more open operating area. An enclosed area degrades the quality of wireless reception and transmission. Verify that the SIM card being used for wireless communication is installed correctly and is not dammaged or malfunctioning. In general, the angle of operation does not affect terminal performance. However, for optimal usage, hold the terminal at an angle not exceeding 30. If the problem persists, contact your VeriFone distributor or service provider. Transactions Cannot be Completed Successfully Wireless Communication Does Not Work D E R Operation with Peripheral Device Not Successful Printer Does Not Print If operation with a peripheral device is not successful:

Verify that the peripheral device is properly connected to the terminal. Replace the cable or the adapter cable being used with the peripheral device. If the problem persists, contact your VeriFone distributor or service provider. Try to verify whether the peripheral device is functioning properly. If the printer does not work properly:

Check the power connection. Recharge or replace the battery. Check that the paper roll compartment cover is fully and securely closed. (See Loading Paper into the Printer). 34 NURIT 8000 INSTALLATION GUIDE TROUBLESHOOTING GUIDELINES Printer Continues Printing When Out of Paper Check that the printer has paper and that the paper and paper roll are properly installed. Take out and then reinsert the paper, if necessary. (See Loading Paper into the Printer). Check that the paper is not jammed or damaged. If it is, reload the paper. (See Loading Paper into the Printer). If the problem persists, contact your VeriFone distributor or service provider. If the printer continues to operate when out of paper:

Check that the paper sensor of the printer mechanism (inside the paper roll compartment) is not blocked by paper or debris. If the problem persists, contact your VeriFone distributor or service provider. If the magnetic stripe card reader does not function properly:

Check that the card has been swiped with its magnetic stripe facing left and at the lower edge of the card, as described in Using the Magnetic Stripe Card Reader. Swipe the magnetic stripe card in the opposite direction. If possible, try using a different magnetic card. If the problem persists, contact your VeriFone distributor or service provider. N A . 3 T F A R V I S I O If the smart card reader does not function properly:

Check that the smart card is fully inserted with the metal chip facing up and at the edge of the card nearest to the smart card reader slot, as described in Using the Smart Card Reader. If possible, try using a different smart card. If the problem persists, contact your VeriFone distributor or service provider. D Printer Continues Printing When Out of Paper Magnetic Stripe Card Reader Does Not Function Properly Smart Card Reader Does Not Function Properly E R The Keypad Does Not Respond If the keypad does not respond:

Refer to user documentation for the particular application in use. If the problem persists, contact your VeriFone distributor or service provider. An Incorrect Response or Data Is Obtained If an incorrect response or data is obtained:

Refer to user documentation for the particular application in use. If the problem persists, contact your VeriFone distributor or service provider. If Tampered Device is displayed on the screen and the keypad is inoperable contact an authorized service representative. Tampered Device Displayed On Screen and Keypad Inoperable NURIT 8000 INSTALLATION GUIDE 35 Service and Support CHAPTER 6 For NURIT 8000 problems, contact your local VeriFone representative or service provider. For NURIT 8000 product service and repair information:

USA VeriFone Service and Support Group, 1-800-834-4366, Monday - Friday, 8 A.M. - 8 P.M., Eastern time. International Contact your VeriFone representative. N A . 3 T Service Returns Before returning the NURIT 8000 to VeriFone, you must obtain a Merchandise Return Authorization (MRA) number. The following procedure describes how to return one or more NURIT 8000 for repair or replacement (U.S. customers only). D F A R V I S I O NOTE E R International customers, please contact your local VeriFone representative for assistance with your service, return, or replacement. 1 Gather the following information from the printed labels (see Figure 22) on the bottom of each NURIT 8000 to be returned:

Product ID, including the model and part number. For example, m108-xxx-xx and PTID xxxxxxxx. Serial number (S/N xxx-xxx-xxx). 2 Within the United States, call VeriFone toll-free at 1-800-834-4366. 3 Select the MRA option from the automated message. The MRA department is open MondayFriday, 8 A.M.8 P.M., eastern time. 4 Give the MRA representative the information gathered in Step 1. If the list of serial numbers is long, you can fax the list, along with the information gathered in Step 1, to the MRA department at 1-727-953-4172

(U.S.). Please address the fax clearly to the attention of the VeriFone MRA Dept. Include a telephone number where you can be reached and your fax number. NURIT 8000 INSTALLATION GUIDE 36 SERVICE AND SUPPORT Accessories and Documentation You will be issued MRA number(s) and the fax will be returned to you. NOTE One MRA number must be issued for each NURIT 8000 you return to VeriFone, even if you are returning several of the same model. 5 Describe the problem(s) and provide the shipping address where the repaired or replacement unit must be returned. Keep a record of the following items:

Assigned MRA number(s). VeriFone serial number assigned to the NURIT 8000 you are returning for service or repair (serial numbers are located on the bottom of the unit as illustrated in Figure 22). Shipping documentation, such as air bill numbers used to trace the Model(s) returned (model numbers are located on the VeriFone label on the bottom of the NURIT 8000). N A . 3 T shipment. F A R V I S I O MODEL/ SERIAL NUMBER 6 D E R Figure 22 Information Label on Unit Bottom VeriFone produces accessories and documentation for the NURIT 8000. When ordering, please refer to the part number in the left column. VeriFone Online Store at www.store.verifone.com USA VeriFone Customer Development Center, 1-800-834-4366, Monday - Friday, 7 A.M. - 8 P.M., eastern time International Contact your VeriFone representative Accessories and Documentation Power Supply AC power cord (United States of America) WIR 30017 Car adapter (universal) 80CA-XX-MXX-BLK NURIT 8000 INSTALLATION GUIDE 37 SERVICE AND SUPPORT Accessories and Documentation The AC power cord varies by country. Contact your local VeriFone representative or service provider to identify the best power cord for your needs. Battery 802B-XX-MXX-BLK Cables Data cable FCL09503 External Modem 80EM-XX-MXX-GRY Documentation To learn more about NURIT 8000, refer to the following set of documents:

NURIT 8000 Quick Installation Guide NURIT 8000 Certifications and Regulations Sheet NURIT 8000 External Modem Quick Installation Guide NURIT 8000 Battery Pack Quick Installation Guide NURIT 8000 Car Adapter Quick Installation Guide N A . 3 T F A R V I S I O D E R VPN VPN DOC113MU01 DOC113MU02 DOC113MU03 38 NURIT 8000 INSTALLATION GUIDE SERVICE AND SUPPORT Accessories and Documentation N A . 3 T F A R V I S I O D E R NURIT 8000 INSTALLATION GUIDE 39 A accessories 37 battery 38 car adapter 37 data cable 38 documentation 38 external modem 38 power cord 37 terminal 37 B battery ordering 38 bottom panel features 14 terminal 14 C cables connecting data 24 ordering data cables 38 car adapter ordering 37 cleaning 31 connecting cables 24 power supply 25, 33 D data connecting cables 24 troubleshooting 35 data cable ordering 38 data connection 24 documentation 37 accessories 38 acronym definitions 6 conventions 5 INDEX related 5 E electrical considerations 11 environmental factors 10 environmental,regulatory, and performance specifications 28 external modem ordering 38 F features bottom panel 14 front panel 13 general 8, 13 front panel features 13 terminal 13 I inserting paper 16 installing SAM card 21 SD/MMC card 23 SIM card 21 terminal location 10 unpack the shipping carton 12 K keypad troubleshooting 35 L loading paper 16 M magnetic stripe card reader troubleshooting 35 using 14 maintenance NURIT 8000 INSTALLATION GUIDE 40 cleaning 31 returning a unit for repair or replacement 36 model 28 modem specifications 28 O operation with peripheral device troubleshooting 34 ordering battery 38 car adapter 37 external modem 38 power cord 37 P paper inserting 16 loading 16 removing 17 physical specifications 28 power troubleshooting 33 power cord 37 ordering 37 power supply 25 connecting 25, 33 specifications 28 printer paper inserting 16 troubleshooting 35 specifications 28 troubleshooting 34 using 16 R removing paper 17 SAM card 22 SIM card 22 repair 36 replacement 36 returning a unit repair 36 INDEX O replacement returning a unit service 36 S SAM card installing 21 removing 22 SD/MMC card removing 23 SD/MMC card installing 23 service returning a unit 36 SIM card installing 21 removing 22 smart card reader troubleshooting 35 using 15 specifications environmental,regulatory, and performance 28 modem 28 physical 28 power supply 28 printer 28 product model 28 temperature and humidity 28 support 36 T tampered device troubleshooting 35 temperature and humidity specifications 28 terminal accessories 37 bottom panel 14 cleaning 31 documentation 37 electrical considerations 11 environmental factors 10 features 13 general 8, 13 front panel 13 installing 10 NURIT 8000 INSTALLATION GUIDE 41 INDEX U location 10 repair 33, 36 replacement 36 service and support 36 specification model 28 troubleshooting 33 transactions troubleshooting 34 troubleshooting data 35 keypad 35 magnetic stripe card reader 35 operation with peripheral device 34 power 33 printer 34 paper 35 smart card reader 35 tampered device 35 terminal 33 transactions 34 wireless communication 34 U using magnetic stripe card reader 14 printer 16 smart card reader 15 W wireless communication troubleshooting 34 42 NURIT 8000 INSTALLATION GUIDE VeriFone, Inc. 2099 Gateway Place, Suite 600 San Jose, CA, 95110 USA Tel: (800) VeriFone (837-4366) www.verifone.com N A . 3 T F A R V I S I O D E R NURIT 8000 Installation Guide VeriFone Part Number DOC113EN05, Revision A