FCC ID: VIXPNMDUAL5M WiFi Monitor

DUAL CONNECT BABY MONITOR with Wi-Fi viewing and dedicated parent unit FP O Whats inside Welcome! .............................................................. xx Getting started .................................................... xx Tour of the system ............................................. xx Everyday use ........................................................ xx Motion detection ............................................ xx Sound detection ............................................. xx Auto-record time............................................ xx Battery life ......................................................... xx Temperature alarm ........................................ xx Music .................................................................... xx Share camera with friend ........................... xx Flip horizontally / vertically ....................... xx Camera time set ............................................. xx Camera info ...................................................... xx Delete Camera ................................................. xx Troubleshooting / FAQs .................................. xx User Guide PNMDUAL5 G e t t i n g S t a r t e d WELCOME!

This WiFi Baby Monitor makes it simple to keep your eyes and ears on your little one from home or from anywhere!

This guide takes you through the steps to get started!

Step 1: Unpack Check out our setup videos On your computer, go to http://bit.ly/pnwi-setup or scan the QR code here. FPO Before you start... Make sure you read the Important Information sheet included in this package. Rechargeable WiFi camera Parent monitor The accessories:

(2) charging cables

(2) power adapters

(2) Mounting screws

(1) 8GB Micro SD card

(pre-installed in the camera) 2 GETTING STARTED Step 2: Charge the monitor Step 3: Position the camera(s) d e t r a t S g n i t t e G Find one of the charging cables included in this package. Plug one end of this cable into the USB CHARGING jack on the side of the parent monitor. Find a location for the camera that gives you the best view of your baby in his or her crib. Plug the other end of the charging cable into one of the included charging adapters. Then plug the adapter into an outlet or surge protector. Place the camera on a at surface, like a dresser or shelf, or mount the camera to a wall using the keyhole slots on its bottom (see the mounting template included in this package). IMPORTANT: NEVER place the camera or cords of any kind inside the crib. NEVER place the camera or cords within reach of the baby. WARNING Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (0.9m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided. 3 G e t t i n g S t a r t e d Step 4: Test your WiFi signal Step 5: Plug in the camera Plug one end of the included charging cable into the DC In jack on the back of the camera. Plug the other end into the included power adapter. Then plug the adapter into an outlet or surge protector. The camera turns on automatically when you plug it in (the indicator light on its back panel turns solid red). Your Project Nursery WiFi Camera needs strong enough signal from your WiFi router in order to send its video signal. Heres how to test the strength of your WiFi signal in your babys nursery using your smartphone or other portable wireless device

(like a tablet or iPod touch). First, go to where you want to put the camera. Make sure your smartphone or other portable wireless device is connected to the WiFi network you want to test. Look at the WiFi icon on your device screen to see the strength of the connection. For example, on iOS devices look in the upper left-hand corner of the screen for the WiFi icon (shown here). For best results, look for a location with at least 50% strength to use the WiFi camera. 4 Step 6: Download and install the Project Nursery Monitor App on your phone or tablet Step 8: Create a Project Nursery user name and password d e t r a t S g n i t t e G In the Google Play or Apple App Stores, search for PROJECT NURSERY MONITOR and look for the icon shown here. Then download and install the App. The rst time you launch the Project Nursery App, youll need to create a user name and password so that you can access your camera securely. Register Login Step 7: Launch the Project Nursery Monitor App Once the Project Nursery Monitor App has installed on your smarphone or tablet, press the icon to launch the App. IMPORTANT!

You must connect the WiFi camera through the App on your phone or tablet before you can connect it to the parent monitor. Username Email Address Password Confirm Password Sign Up Press the Register button to start, then follow the steps to set up your account. IMPORTANT: Make sure you give a valid email address that you have easy access to. The App will use this address if you ever need to recover or reset your password. Once youve nished creating your user name and password, the App will ask you to Login with the name and password you created. IMPORTANT: Your user name cannot contain special characters (like @)only letters and numbers. 5 G e t t i n g S t a r t e d Step 9: Pair the WiFi camera with the App. Make sure the Project Nursery App is open on your phone or tablet. Also make sure that your phone or tablet is connected to your WiFi network. In the Apps home screen, press the Camera) in the upper right corner of the screen. icon (Add Device List Message My Center Add Camera Add new camera with WiFi Add new camera with QR code Get shared camera from friend In the next screen, press the Add new camera with WiFi button. The App will prompt you to make sure your camera is on. If you havent already turned it on, press the POWER button on the right side of the camera (the cameras LED lights up), then press the Next step button in the App. 6 Add Camera Scan QR code located on bottom of camera Press to open QR code scanner ID:

Camera name:

Next step The next screen in the App lets you name the camera youre setting up and prompts you to scan the QR code on the bottom of the camera. To name the camera youre setting up: Press in the Camera name eld and enter the name you want to use. To scan the QR code on the WiFi camera: Find the QR code on the bottom of the WiFi camera. Position your smartphone or tablet so that its camera can scan this QR code. Then press where indicated in the App to scan this QR code. Configure WiFi 1. Your camera should be plugged in and turned ON. Press the Set button on the bottom of your camera for 1 second.You will hear one beep and the LED will start blinking red. 2. Choose WiFi SSID (or network name) and enter password below. Make sure you enter the info correctly. If your WiFi SSID does not have a password, you will need to create one. This is for your safety and security. Consult the user guide for your WiFi router/AP to add a password. Helpful Hint: Click on the lock icon in the password area to hide or display text. 3. After youve entered your WiFi info below, press Next step. Your camera will begin connecting to your WiFi network. This can take 23 minutes to complete. When you hear two beeps and the LED turns solid green, your camera is successfully connected and ready for you to use. Next step After youve scanned the QR code on the bottom of the WiFi Camera, the App will ask you to press the SET button on the bottom of the camera and enter the name (WIFI SSID) and password of your WiFi network. Find the SET button on the bottom of the WiFi camera. Press it for one second (until the camera gives an audio signal). Next step Enter the name (WIFI SSID) and password for your home WiFi network in the App. IMPORTANT: Double check that youve typed your network name and password correctly otherwise, the camera wont work with the App!

d e t r a t S g n i t t e G Once youve nished entering your network name and password, press the Next step button on the App screen. The indicator light on the back of the WiFi camera starts ashing the camera is trying to join your WiFi network. Congratulations!

Camera successfully added!

Once the WiFi camera has successfully connected to your WiFi network, youll see the Success screen in the App and the indicator light on the back of the camera will turn green. Congratulationsyouve just set up your rst camera!

IMPORTANT: If this WiFi setup option doesnt work, try the Add new camera with QR code option in the Add Camera screen. If the WiFi camera does not connect, follow the instructions in the App to troubleshoot. 7 G e t t i n g S t a r t e d Step 10: Choose the camera from the home screen Congratulations! Youve just set up the camera for viewing on your smartphone. Now its time to set it up with the local monitor. Connection Troubleshooting

+ Make sure your phone or tablet is connected to the WiFi network you want to use.

+ Make sure the camera is getting a good signal from your WiFi router. See step 3 for more information.

+ Test your WiFi network with other devices to make sure its working.

+ Double check that youve entered the correct password for your WiFi network in the Project Nursery App.

+ Make sure your router is broadcasting its SSID

(name). The Project Nursery WiFi camera does not support hidden SSIDs.

+ Make sure that Wi-Fi signal is 2.4GHz. The Project Nursery WiFi camera does not support 5GHz WiFi.

+ Make sure that your WiFi router uses either WPA2-PSK/WPA-PSK or AES as its encryption method.

+ Make sure that there is no MAC lter on router or add MAC address to router whitelist.

+ Reset the camera to set up connection again. Press and hold SET key for 10 seconds. The camera gives a long beep when it is fully reset. Sallys nursery Device ID1234567891234560 Press the part of the home screen showing the camera you set up in order to choose this camera. The Camera View screen is your gateway to total control of your WiFi camera from virtually anywhere. The next chapter gives you a tour of the features available from this screen. Sallys nursery Device ID1234567891234560 Device List Message My Center Sallys nursery 0 0000000000000000000000000000000000000000000 2016-1-28-12:00 H D SD RECORD SNAPSHOT Swipe screen above to Pan/Tilt TALK SOUND ON 8 d e t r a t S g n i t t e G Step 11: Turn on the monitor Then press Password and use the on-screen keyboard to enter the password for this network. Press and hold the POWER button on the parent monitor to turn it on. Step 12: Connect the monitor to your WiFi network WiFi Network Password CONNECT WELCOME!

WiFi Network Home WiFi Sig_Guest Comcast_123 The rst time you turn on the parent monitor, youll be asked to choose your WiFi network and enter its password. Press WiFi Network and choose your network from the list that appears.

?

?

IMPORTANT: Make sure you use the same WiFi network you used to set up the camera with the App!

myNetwork netwkpass1 CONNECT WELCOME!

Once youve chosen your network and entered your password, press the CONNECT button to connect to it.

?

The process of connecting the monitor and camera to your WiFi network might take several minutes to complete. 72 10:30AM Once the monitor and camera have connected to your WiFi network, you should start seeing video from the camera on your monitor. 9 T o u r o f t h e s y s t e m TOUR OF THE SYSTEM Parent Monitor turns the monitor on and off (press and hold for 1 second). turns the screen on and off. Press and hold for 2 seconds to switch cameras. turn the volume down/up (you can and also do this through the touchscreen). In menu screens, these navigate left/right. zooms the camera in and out (you can also do this through the touchscreen). This button also selects items in menu screens. starts pan/tilt of the camera (you can also do this through the touchscreen). Use the arrows to pan and tilt once youve activated this function. This button also navigates up in menu screens. lets you talk through the cameras speaker

(you can also do this through the touchscreen). Press and hold while talking (release when youre done). This button also navigates down in menu screens. SOUND LEVEL indicators show you the level of sound from your babys room. USB CHARGING jack (side panel, not shown) plugs into your charging cable to recharge or power the parent monitor. Watching baby You can turn the display on and off without turning the monitor off (this can help extend battery life). Youll still hear your baby, but the display will be asleep until you awaken it. To turn the display on or off: Press the VIDEO ON/

OFF button on the parent monitor. 10 Parent Monitor Touchscreen 72 10:30AM Pan, Tilt, and Zoom To zoom the active camera: Touch the parent monitors touchscreen, then press also press the OK-ZOOM button. To pan or tilt the active camera: Touch the parent monitors touchscreen, then press one of the arrow icons. You can also press the PAN/TILT button and use the arrow buttons. You can Almost all of the parent monitors features are accessible through its touchscreen. Just tap the screen to see icons for each feature. and turn the volume down/up. pan and tilt the camera. accesses the parent monitors menu system. zooms in on the camera image. m e t s y s e h t f o r u o T lets you talk through the cameras speaker. Press and hold while talking. clears the icons from the screen. Listening to baby Talking to baby The SOUND LEVEL indicators on the parent monitor show you at a glance the sound level in your babys room, regardless of how loud the audio is on the parent monitor. To talk through the speaker on the active camera:

Touch the parent monitors touchscreen, then press and hold TALK button on the parent monitor. You can also press and hold the To increase or decrease the volume of the audio monitor: Press the VOL+ or VOL buttons on the parent monitor. Talk normally to the parent monitoryour voice will come out on the cameras speaker. Release the on-

screen microphone icon when youre done talking. 11 Sallys nursery 0 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000 2016-1-28-12:00 App Camera View Screen

(Settings) accesses the Settings menu for this camera. Press this icon to adjust the WiFi and other settings for this camera. Camera view shows you the image from your WiFi camera. Pan and tilt the camera by swiping on the screen left/right or up/down. Zoom the camera by double-tapping the screen. H D SD

(Multi-Camera View) lets you see multiple cameras at once on a single screen (if youve set up multiple cameras). Press this icon to access the multi-camera view screen (phone App only). RECORD SNAPSHOT H D SD (HD-SD Select) lets you switch between high- and standard-

denition video on the view screen. T o u r o f t h e s y s t e m

(Micro-SD Card) accesses any content stored on the cameras Micro-

SD Card (not included). Press this icon to start viewing or downloading motion/sound-activated videos or images from the cameras Micro-SD Card. (This is where youll see auto recordings.) RECORD (Record) starts/stops recording video. The video le is saved to your smartphone or tablet. SNAPSHOT (Snapshot) takes a still photo of the camera video. The snapshot le is saved to your smartphone or tablet. TALK (Talk) lets you speak through this cameras built-in speaker. Press and hold this icon to start speaking. SOUND ON (Sound On/Off) turns the sound from the camera on and off. Swipe screen above to Pan/Tilt TALK SOUND ON Pan, Tilt, and Zoom To zoom the active camera: Double-tap the camera view screen. To pan or tilt the active camera: Swipe the camera view screen left/

right or up/down. 12 Camera (front) Camera (bottom) Camera (back) Nighttime sensor adjusts the camera sensitivity to the amount of ambient light. Microphone picks up sound around the camera. POWER button

(right side) turns the camera on and off (press and hold). Mounting keyholes let you mount the camera on a wall (mounting screws included). DUAL MICRO-SD slot (left side) holds the pre-

installed micro-SD card for storage of automatic photos/

video. SET starts the WiFi setup process (press and hold). QR code passes the camera ID information to the App during the WiFi setup process. m e t s y s e h t f o r u o T Adjustable antenna communicates wirelessly with your WiFi network. DC In jack plugs into your charging cable to power the camera. Indicator light shows the power and connection status of the camera:

- off (camera not plugged in or powered on)

- solid red (on but not connected

- blinking red (in the process of connecting)

- solid green (connected to network and App)

- blinking green (camera being actively viewed on monitor or App). Thermal sensor detects the temperature around the camera. 13 3. EVERYDAY USE You customize your Dual-Connect Baby Monitor System to best t your needs and environment, including motion, sound, and temperature alerts that notify you automatically. Access these settings through the App on your phone/tablet or through the menu system on the parent monitor. This chapter takes you through the settings you can customize, one by one. Sallys nursery 2016-1-28-12:00 0 0000000000000000000000000000000000000 Settings H D SD RECORD SNAPSHOT Motion detection H Sound detection Battery Life M H L L OFF OFF Swipe screen above to Pan/Tilt Auto-record time 20s 60s 90s TALK SOUND ON Temperature alarm M i Whit N i To access the App menu system: In the Camera View screen, press the

(Settings) icon. 72 10:30AM 10:30AM To access the parent monitor menu system:

Touch the screen. Then press the icon. E v e r y d a y u s e 72 14 72 10:30AM 72 72 View Cameras Scan Cameras 10:30AM 1 3 2 4 View Cameras Scan Cameras 10:30AM 5 sces 15 sces 10 sces OFF Sound Activated Scan Cameras (Parent Monitor only) The Cameras menu on the parent monitor lets you change which camera youre viewing (if you have multiple cameras set up). It also offers several options for scanning through the cameras automatically. IN THE APP: If you have multiple cameras set up, you can view up to 4 at once on the App using the screen. button in the camera view ACCESSING CAMERAS ON THE PARENT MONITOR 1 Touch the parent monitors screen. Then press the 2 Press the Cameras icon. To view a different camera: In the Cameras menu, press View Cameras. Then press the icon for the camera you want to view. The screen switches to that camera, and the status bar at the top of the screen indicates the camera youre viewing:

icon.

, or

,

,

. e s u y a d y r e v E To scan through the cameras automatically: In the Cameras menu, press Scan Cameras. Select the scan option you want:

switch every 5, 10, or 15 seconds, or sound-activated scan. The screen switches to the rst camera, and the status bar at the top of the screen shows an indicator for scanning:

,

, or

. It also shows the camera youre viewing Note: You must have Sound Activated Video alerts turned on for the Sound Activated Scan to work. See the next page for details. To stop scanning cameras: select Scan Cameras in the Cameras menu. Then select Off. 15 Motion/Alerts The Dual Connect System lets you set up alerts that are activated by motion, sound, or temperature in your babys room. It also lets you set up an alert for when the monitors rechargeable battery needs to be recharged. You can set up these alerts through the parent monitor or through the App. SETTING ALERTS ON THE PARENT MONITOR 1 Touch the parent monitors screen. Then press the 2 Press the MOTION/ALERTS icon. 3 Select the kind of alert you would like to set. Motion Activated Video automatically shows video when the active camera detects movement. It has three levels of sensitivity: Low, Medium, and High. Once youve selected the level of sensitivity you want, the status bar at the top of the screen shows an indicator for motion activation:

When the active camera senses motion, this indicator ashes. icon. Sound Activated Video automatically shows video when the active camera detects sound. It has two levels of sensitivity:

Low and High. Once youve selected the level of sensitivity you want, the status bar at the top of the screen shows an indicator for sound activation:

. When the active camera senses sound, this indicator ashes. Temperature Alert noties you when your babys room is too hot or too cold. There are separate alerts for High and Low temperatures. Press the one you want to set, then use the + and on-screen buttons to set the temperatures you want. Once youve set these up, the status bar at the top of the screen shows an indicator for temperature alerts: . 72 10:30AM E v e r y d a y u s e 72 10:30AM Motion Activated Video Sound Activated Video Temperature Alert Low Battery Alert Out of Range Alert Note about alert sensitivity:

You might want to test different levels of sensitivity for motion, sound, and temperature alerts, to nd the best t for your environment and preference. 16 Notes about notications:

+ Motion, sound, and temperature alerts you set on the parent monitor will send notications on the App as well (if you have App notications turned on).

+ The App sends a maximum of 2 notications every 4 minutes. It prioritizes notications in the following order: temperature, sound, motion. If the temperature in your babys room goes beyond the limit(s) you set, the parent monitor displays an alert and the temperature alert indicator turns red in the status bar. Low Battery Alert tells you when the monitor needs to be recharged.. Once youve turned this alert on, the status bar at the top of the screen shows an indicator for low-battery alert: . Out of Range Alert tells you when the monitor is disconnected from or out of range of the camera (for example, if the cameras lost power). Once youve turned this alert on, the status bar at the top of the screen shows an indicator for out-of-range alert: . Sallys nursery 0 0000000000000000000000000000000000000000000000000 2016-1-28-12:00 Settings H D SD Motion detection H RECORD SNAPSHOT Sound detection Battery Life M H L L OFF OFF Swipe screen above to Pan/Tilt TALK SOUND ON Auto-record time 20s 60s 90s Temperature alarm Music White Noise Share camera with friend Flip horizontally Flip vertically Camera time set Camera info Delete Camera SETTING ALERTS ON THE APP 1 2 In the Camera View screen, press the In the Settings menu, set the sensitivity of the alerts you want to set.

(Settings) icon. e s u y a d y r e v E Motion detection sends a notication on your phone when the camera detects movement. It has three levels of sensitivity: H (high), M (medium), and L (low). Sound detection sends a notication on your phone when the camera detects sound. It has two levels of sensitivity: H

(high) and L (low). Battery life sends a push notication when the rechargeable battery in the WiFi camera gets to a certain level. Select Battery life, then press the switch next to Push Notications for Camera Battery and choose when you would like to be sent notications. 17 Auto-record time automatically records a certain amount of video when the camera detects a motion or sound alert.Select the amount of Auto-record time you want (in seconds) when a motion or sound alert is triggered: 20s, 60s, or 90s. IMPORTANT: You must keep the provided micro SD card in its slot on the camera to use this feature. Temperature Alarm sends a push notication to your phone when your babys room is too hot or too cold. Select Temperature alarm, then press Edit at the top of the screen to change the settings. To change from degrees Fahrenheit to Celsius:

Press the C. To set a high temperature alert: Press the switch next to High temperature alert. Then set the temperature you want for the high temperature alert. To set a low temperature alert: Press the switch next to Low temperature alert. Then set the temperature you want for the high temperature alert. Temperature alarm E v e r y d a y u s e 18 72 10:30AM NOTE: If theres a lullaby currently playing on a camera, a green arrow icon appears next to it. Music White Noise MusicMusic

"I Don't Want to Miss a Thing"

"Holiday"

"Jolene"

Rain Waves White Noise Lullabies This Project Nursery system comes with 3 lullabies, 2 nature sounds, and white noise ready to playsimply choose the one you want, and the camera youre on will play it back. CONTROLLING LULLABIES FROM THE PARENT MONITOR 1 Make sure the monitor is displaying the camera you want to play the lullaby on. If you want to play on a different camera, press the MENU button and select CAMERAS. Then select View Camera and choose the camera you want. 2 Press the MENU button to access the main menu. 3 Press the LULLABIES icon. 4 Press the option you want to play. The status bar at the top of the screen shows an indicator for lullabies:

. e s u y a d y r e v E CONTROLLING LULLABIES FROM THE APP To play a lullaby, nature sound, or white noise from the active camera: Press Music in the Setup menu. Then press the option you want to play. Note: Make sure youre displaying the camera you want to play the lullaby on. If you want to play on a different camera, go back to the Apps home screen and choose that camera. 19 Sleep Mode (Parent Monitor only) You can set up the parent monitor to turn off the display automatically after a set amount of time. SETTING SLEEP MODE 1 Press MENU on the parent monitor. 2 Press the Sleep Mode icon. 3 In the Sleep Mode menu, press Sleep Mode (video off, audio only) to turn sleep mode on. Then select the delay before the display turns off automatically: 5, 30, or 60 minutes. (The audio from your camera will stay on even when the display is off.) Playing Back Pictures and Videos You can access the videos or pictures stored on the cameras SD card from the parent monitor and from the App. IMPORTANT:

You must keep the provided micro SD card in its slot on the camera to use this featurethis is where motion and sound-

activated videos are stored. 72 10:30AM Sleep Mode(video off audio only) 5mins 30mins 60mins OFF E v e r y d a y u s e 20 ACCESSING PICTURES/VIDEOS FROM THE PARENT MONITOR 1 Press MENU on the parent monitor. 2 Press the Play icon. 3 Press the button for the kind of media you want to play back: Photo or Video. 4 The screen displays a list of the photos or videos on the cameras SD card. Press the name of the image or video you want to see on the display. 5 Use the on-screen controls to stop, play/pause, and exit the screen. ACCESSING PICTURES/VIDEOS FROM THE APP 1 Press 2 Choose the photo or video you want to start playing. on the camera view screen in the App e s u y a d y r e v E 72 Photo Video 10:30AM 201600309002.jpg 201600309003.jpg 201600309011.jpg 201600309012.jpg Sallys nursery 2016-1-28-12:00 0 000000000000000000000000000000000000000000000000000000000000000000000000000 H D SD RECORD SNAPSHOT Swipe screen above to Pan/Tilt TALK SOUND ON 21 Settings (Parent Menu only) The Settings menu lets you customize the monitor to match your preferences. It also gives you technical information about the monitor and support. ACCESSING THE PARENT MONITORS SETTINGS MENU 1 Press MENU on the parent monitor. 2 Press the Settings icon. 3 Press the setting youd like to adjust. (Press the arrow down at the bottom of the list if you dont see the setting you want.) Wi Set lets you enter the network name and password for your monitor and camera. IMPORTANT: This must be the same network you used to set up the camera through the App. If you want to change networks, delete the camara in the App and follow the setup instructions from the beginning with the new network. Adjust Brightness lets you adjust the level of brightness on the parent monitor. Press this option, then use the + and on-screen buttons to set the level desired. Auto Dimming lets you adjust the amount of time of inactivity before the parent monitor dims its display brightness to conserve energy. Press this option, then select the amount of time desired: 5, 10, or 15 minutes. Time Set lets you adjust the time displayed on the parent monitor. Press this option, then use the up and down on-

screen buttons to set the hours, minutes, and AM/PM. 72 10:30AM E v e r y d a y u s e 72 10:30AM Wifi Set Adjust Brightness Auto Dimming Time Set Temperature 22 72 10:30AM French English Language Select Factory Reset Support Temperature lets you select how youd like temperature to be displayed: in degrees Fahrenheit or Celsius. Language Select lets you select the language you want for the menu system on the parent monitor. Factory Reset lets you return the parent monitor to the settings it had when you got it out of the box. If youve tried all of the troubleshooting solutions to solve a problem, and nothing seems to work, you might need to reset the monitor to its factory settings and start setup again. WARNING:

Resetting to factory settings erases all of your custom settings. You will have to set up the monitor from scratch. Support gives you information about the rmware version used in your monitor and camera. It also provides customer support information. Share camera with friend Share camera with friend (App only) You can share video with friends and family, so that they can see whats happening with baby. These guest accounts have limited access to settingsthey can view and talk through cameras and record pictures and videos directly to their phone. 1 Make sure the person you want to share with has e s u y a d y r e v E Steps to share with friend Decice List Add Camera Add new camera with WiFi Add new camera with QR code Get shared camera from friend Step 1: Open App and click then Add camera button above in your friends mobile phone Step 2: Select the third option and scan the QR code above downloaded the Project Nursery App on their phone/tablet. 2 On your phone or tablet, go to the Settings menu and press Share camera with friend. Have the person you want to share with follow the steps shown. IMPORTANT: Your friend or family member will need to scan the QR code on the screen. If they are not physically present to do so, either print the screen or do a screenshot and send it to a phone they can scan with their phone. 23 Flip horizontally Flip vertically Flip horizontally / vertically (App only) Flip horizontally and vertically let you reverse the orientation of the Camera View video. Press the switches next to each to toggle these on and off. Camera time set Camera time set (App only) The camera time on the screen is from network. If you find the camera time is not the same with the mobile phone, please click the button below to synchronize time. Camera info Device name Serial #

MAC address IP Camera 215451516514 442412314575756 Hardware version 20130101 Software version BNHS5750101 E v e r y d a y u s e The WiFi cameras internal clock might need to be periodically syncronized with your phones clock. If you notice the two times dont match, choose Camera time set in the Apps Settings menu, and press the Camera time sync button at the bottom of the page. The App will sync the current WiFi cameras clock with your phone or tablets clock. Camera info (App only) The Device info screen gives you details about the current WiFi camera, including the amount of memory left on the micro-SD card if you have one installed. The Format SD card button at the bottom of the Camera info screen lets you format a micro-SD card before you use it for the rst time. Space capacity Use Available 3.0GB 2.0GB To format a micro-SD card: Insert the card into the WiFi cameras micro-SD card slot. Then press the Format SD card button at the bottom of the Camera info page. Delete Camera Delete Camera (App only) If youve tried all of the troubleshooting solutions to solve a problem, and nothing seems to work, you might need to reset the WiFi camera and App to their factory settings and start setup again. WARNING: Delete camera erases all of your custom settings. You will have to set up the WiFi camera from scratch. 24 4. TROUBLESHOOTING / FAQS Most issues with the Project Nursery baby monitoring system can be solved by following one of the troubleshooting tips below. For additional assistance, please call 1-844-393-7338. WiFi Issues I cant connect the WiFi camera to my network.

+ Make sure your phone or tablet is connected to the WiFi network you want to use.

+ Make sure the camera is getting a good signal from your WiFi router. See page xx for more information.

+ Make sure that Wi-Fi signal is 2.4GHz. The Project Nursery WiFi camera does not support 5GHz WiFi.

+ Make sure that your WiFi router uses either WPA2-PSK/WPA-PSK or AES as its encryption method.

+ Make sure that there is no MAC lter on router or add MAC address to router whitelist.

+ Reset the camera to set up connection again. Press and hold SET key for 10 seconds. The camera will give a long beep when it is fully reset. The WiFi cameras indicator light remains red (connection to network failed).

+ Double check that youve entered the correct password for your WiFi network in the Project Nursery App.

+ Test your WiFi network with other devices to make sure its working.

+ Make sure the camera is getting a good signal from your WiFi router. See page xx for more information.

+ Make sure that Wi-Fi signal is 2.4GHz. The Project Nursery WiFi camera does not support 5GHz WiFi.

+ Make sure that your WiFi router uses either WPA2-PSK/WPA-PSK or AES as its encryption method. Camera Issues The WiFi cameras indicator light ashes green.

+ The camera is being actively viewed. g n i t o o h s e l b u o r T 25 I dont see video from the camera on my phone/tablet.

+ Make sure the camera is turned on and that it has enough charge or is plugged in to a working outlet.

+ Make sure the camera is within range of your WiFi router (certain kinds of signal obstacles, like large metal objects, might shorten the range somewhat).

+ Make sure your phone/tablet has an active data or WiFi connection and that the Project Nursery App is open and congured with the camera. I cant record video or pictures on the camera (for motion or sound alerts).

+ Make sure you have an Micro SD card (included) inserted in the MICRO SD card slot on the side of the camera.

+ Make sure auto-record is set to on and a motion or sound alert is set. App Issues I cant record video or pictures on my phone/tablet.

+ Make sure your phone/tablet has enough available memory to record video or pictures. My video feed is frozen.

+ Check the time stamp on the video feed screen to make sure the video is frozen. Then return to the camera home screen and reload that camera again.

+ Close the app and re-open. I cant pan/tilt the camera from my phone or tablet.

+ Make sure youre swiping on the video from the camera on your phone or tablet. Pan and tilt the camera by swiping on the screen left/right or up/down. Zoom the camera by double-tapping the screen.

+ Make sure the camera is moving freely. In certain positions, the camera might bump into the stand neck. If the neck is in the way, pan or tilt the camera in the other direction so that you have a free range of movement. The App is frozen.

+ Force close the App on your phone or tablet. Then re-open it. T r o u b l e s h o o t i n g 26 I cant hear sounds from babys room.

+ Make sure the volume on your phone or tablet is turned up.

+ Make sure sound is turned on in the Camera view screen.

+ Make sure the microphone on the camera is not blocked. The microphone is just below the lens. The lullabies/sounds arent playing.

+ If you have multiple cameras, make sure youve chosen the one you want the lullabies to play on before you start the lullaby. Go to the Home screen and choose the camera you want. Then go to Settings, then Music and select an option to play. The temperature alerts dont work.

+ Make sure youve set the temperature preference to the system you use, Fahrenheit (standard in the US) or Celsius (standard outside the US). To switch your temperature preference, go to Settings > Temperature alarm.

+ Make sure youve set the right kind of temperature alertfor example, if you want to make sure your babys room does not get below 68 degrees Fahrenheit, set the Low Temperature Alert to 68. If you want to make sure your babys room doesnt get above a certain temperature, set the High Temperature Alert to that temperature. Motion alerts dont work.

+ You might need to adjust the sensitivity of the alertsfor example, if Motion detection is set to Low, the monitor will not come on as often as when Motion detection is set to Medium or High. To adjust this setting, go to Settings > Motion detection.

+ If you have multiple cameras, you might need to set an alert for the camera youre usingmotion alerts need to be set separately for each camera.

+ The App gives a maximum of 2 notications every 4 minutes. Sound alerts dont work.

+ You might need to adjust the sensitivity of the alertsfor example, if Sound detection is set to Low, the monitor will not come on as often as when Sound detection is set to High. To adjust this setting, go to Settings > Sound detection.

+ If you have multiple cameras, you might need to set an alert for the camera youre usingsound alerts need to be set separately for each camera.

+ The App gives a maximum of 2 notications every 4 minutes. g n i t o o h s e l b u o r T 27 Id like to stop sharing the camera view with a friend/family member.

+ Go to the Settings menu in the Project Nursery App on your phone/tablet and select Delete camera at the bottom of the menu. This will stop all sharing, but youll need to set up the camera again on your phone. Id like to give someone full access to my camera (including settings).

+ Guess accounts have limited access to settings. If you want to give someone full access, you will need to give them your account log-in info and password (not recommended!). I cant access the camera from my computer.

+ The Project Nursery WiFi camera works with the Project Nursery App on iOS and Android devices only. It does not support computers or other mobile device operating systems. I cant open the App on my Android tablet.

+ The Project Nursery App is not compatible with some makes and models of Android tablets. Contact our customer service at 1-844-393-7338 to see if your Android tablet is compatible with the Project Nursery App. Parent Monitor Issues I dont see video from the camera on my monitor.

+ Make sure your monitor is turned on (press the Power button). If it is, press the VIDEO ON/OFF button

(VIDEO on the mini monitor) to make sure the monitors display is awake. Make sure the camera is plugged in to a working outlet and turned on. icon on the screen. I see the

+ Make sure the camera youre trying to view is plugged in to a working outlet and turned on.

+ Make sure the monitor is on the same WiFi network as the camera was set up on in the App. I cant record video or pictures.

+ Make sure you have an Micro SD card (included) inserted in the MICRO SD card slot on the side of the camera. I cant pan/tilt the camera from my monitor.

+ Make sure youre in pan modepress and hold OK/ZOOM until you see arrows on the monitor display. Then use the arrows or joystick to pan the camera.

+ Make sure youre not zoomed in on the imagepress OK/ZOOM to zoom out if you are. Then press and hold OK/ZOOM to enter pan mode. T r o u b l e s h o o t i n g 28

+ Make sure the camera is moving freely. In certain positions, the camera might bump into stand neck. If the neck is in the way, pan or tilt the camera in the other direction so that you have a free range of movement. I cant hear sounds from babys room.

+ Make sure the monitor is turned up. Press the VOL+ button until you hear sounds from your babys room.

+ Make sure the microphone on the camera is not blocked. The microphone is just above the lens. The lullabies arent playing.

+ If you have multiple cameras, make sure youve chosen the one you want the lullabies to play on before you start the lullaby. Go to Cameras > Select Camera and choose the camera you want. Then go to Lullabies and select an option to play. The temperature alerts dont work.

+ Make sure youve set the temperature preference to the system you use, Fahrenheit (standard in the US) or Celsius (standard outside the US). To switch your temperature preference, go to Settings > Temperature.

+ Make sure youve set the right kind of temperature alertfor example, if you want to make sure your babys room does not get below 68 degrees Fahrenheit, set the Low Temp Temperature Alert to 68. If you want to make sure your babys room doesnt get above a certain temperature, set the High Temp Temperature Alert to that temperature. Motion alerts dont work.

+ You might need to adjust the sensitivity of the alertsfor example, if Motion Activated Video is set to ON:

Low, the monitor will not come on as often as when Motion Activated Video is set to ON: Medium or ON:

High. To adjust this setting, go to Motion/Alerts > Motion Activated Video.

+ If you have multiple cameras, you might need to change the active cameramotion alerts work for the active camera only. Press VIDEO ON/OFF (VIDEO on the mini monitor) to make sure the camera you want to use for motion alertsthe one with the clearest view of your baby, for exampleis the one displayed. Sound alerts dont work.

+ You might need to adjust the sensitivity of the alertsfor example, if Sound Activated Video is set to ON:

Low, the monitor will not come on as often as when Sound Activated Video is set to ON: Medium or ON:

High. To adjust this setting, go to Motion/Alerts > Sound Activated Video.

+ If you have multiple cameras, you might need to change the active camerasound alerts work for the active camera only. Press VIDEO ON/OFF (VIDEO on the mini monitor) to make sure the camera you want to use for sound alertsthe one closest to your baby, for exampleis the one displayed. g n i t o o h s e l b u o r T 29 2017 Voxx Accessories Corp. 3502 Woodview Trace, Suite 220 Indianapolis, IN 46268 PNMDUAL5 IB 00