FCC ID: XGB-TB2265 EAR FORCE X32 Headset

User Guide 5GHz WiFi dual band wireless 11 Whats in the Box R T O N E X32 Headset XBOX 360 Talkback Cable

(2) AAA Batteries X32 Wireless Digital RF Transmitter RCA Splitter Cable Turtle Beach Sticker TURTLEBEACH.COM watch X32 training videos at:

www.youtube.com/TurtleBeachVideos product support and warranty information:

www.TurtleBeach.com/support Table of Contents X32 Headset X32 Transmitter Overview Using the Transmitter Pairing the Headset and Transmitter Setup Equalizer and Sound Field Expander Presets Chat Boost Technical Specications Troubleshooting Important Safety Information pg 1 pg 2 pg 3 pg 4 pg 5 pg 11 pg 12 pg 13 pg 14 pg 14 X32 Headset 2 3 4 5 6 OPEN T O N E 1 1 1 2 3 4 5 6 Tone Button: Press this button to activate the different EQ presets. A beep will indicate which preset is selected. (see pg. 11) XBOX Controller Jack: Insert the straight connector on the talkback cable here. (see pg. 8) Effects Button: Press this button to activate the different Sound Field presets. A beep will indicate which preset is selected. (see pg. 11) Game Volume: Turn to adjust the game sound level. The XBOX LIVE chat volume may be independently set by the volume control on the talkback cable. Power Button: Turn on the headset by pressing the power button for a couple of seconds, then release. You will hear 2 beeps and the power LED should start ashing. Turn off the headset by pressing the button until the LED stays on and you hear 2 beeps, then release. To enter Pairing Mode, press and hold the power button for about 6 seconds until you hear 2 fast beeps and the LED begins to ash rapidly (see pg 4). The headset will turn off after several minutes if theres no audio detected or if the transmitter is turned off. Battery Compartment Cover Slide down the panel on the right ear cup to access the battery compartment. The headset is powered by (2) AAA batteries (included) which should provide up to 15 hours of use. Rechargeable NiMH batteries may also be used. A tone will sound every 6 seconds when battery power is low. NOTE: Be sure to insert the batteries as shown. X32 Transmitter 1 1 2 3 4 Power/Link LED: When the transmitter is powered on and communicating with the headset, this LED will be on solid. When the headset is turned off, the LED on the transmitter will turn off. A slowly pulsing LED indicates that the transmitter cant communicate with the headset. This could happen when the headset is out of range or not paired with the transmitter. (see pgs. 3-4) Game Audio Input Jack Insert the 3.5mm end of the included RCA Splitter Cable into this jack. Auxiliary Input Jack: Provides a 3.5mm input for digital music players or additional audio sources. (3.5mm cable sold separately) Pairing Button: Press and hold to activate pairing mode. (See pg. 4) 2 3 4 2 Using the Transmitter Transmitter Range The transmitter sends game audio from your Xbox 360 to the headset via digital radio frequency (RF) signal, so a direct line of sight is not required. When youre out of range, you may hear popping or clicking sounds if the headset loses the RF signal. For best performance, place the transmitter in an open area that is unobstructed by objects that might absorb RF signals from the internal antenna. Avoid placing it on a metal surface, such as the top of a home theater A/V receiver. R Optimum range: within 20 ft. T O N E Dual-Band WiFi The X32 uses advanced Dual-Band WiFi radio technology to help eliminate interference with additional wireless devices and WiFi networks. The dual-band radio uses both 5GHz and 2.4GHz signals to transmit high delity digital audio and help eliminate interference with other wireless devices. Unlike the RF technology used in most other wireless headsets, this dual-band WiFi radio technology coexists with wireless networks for optimum performance. 5GHz WiFi dual band wireless 3 Pairing the Headset and Transmitter The headset and transmitter in this package are paired, which means theyre synchronized to ensure they work together. When the headset and transmitter are communicating, the top LED on the front panel of the transmitter will be on solid. If this LED is instead slowly pulsing, it means the transmitter cant communicate with the headset. This could happen when the headset is out of range or not paired with the transmitter. If the LED is slowly pulsing when the headset is on and within range, then they might need to be paired as described below:

Step 1:

Make sure the headset is turned off. Step 2:

Press and hold the headset power button for about 6 sec-

onds until you hear 2 fast beeps and the LED begins to ash rapidly, then release. Step 3:

Press and hold the PAIR button on the transmitter. The transmitter LED will beging to ash rapidly. When the Power/Link LED on the transmitter turns off, release the button. After a few seconds, the Power/Link LED on the transmitter should be on solid and the headset LED should be ashing about once per second, indicating that the units are paired. T O N E 2 1 3 Interference from Two Headsets Only one headset can be paired with the transmitter. If you pair two headsets with the same transmitter, theyll interfere with each other as they compete for the transmitter RF signal. This will cause one headset to shut off. So dont try to pair two headsets with the same transmitter!

4 XBOX 360 Setup (HDMI) Transmitter USB Cable RCA Splitter Cable

(included) HDMI XBOX 360 Audio Adapter Cable*

(sold separately)

* All XBOX 360 models require an XBOX 360 Audio Adapter Cable for audio output when used with an HDMI connection (available from third party sellers). NOTE: If your HDMI TV has red/white RCA AUDIO OUT jacks you can use it to feed the sound from your TV to your Turtle Beach headset. (AUDIO IN jacks will not send sound out to your headset, you need AUDIO OUT as shown in the alternate setup.) 5 XBOX 360 Setup (HDMI)

(Alternate Setup) Transmitter USB Cable RCA Splitter Cable

(included) HDMI 6 XBOX 360 Setup (RCA) Transmitter USB Cable XBOX 360 AV Cable RCA Splitter Cable

(included) 7 XBOX 360 Chat Setup 1. Insert the right angle plug into the headphone jack on the XBOX 360 controller. 2. Insert straight plug into the controller jack on the left ear cup of the headset. Mic Mute Chat Volume Congure XBOX 360 Settings Voice Voice Volume 10 Game Volume 10 Mute Kinect Voice Output Play Through Headset Play Through Speakers Voice Output Xbox 360 Controller R T O N E Xbox 360 Input Xbox 360 Talkback Cable 1. Press the XBOX 360 Guide Button, select

"Settings > Preferences > Voice"

2. Voice Volume = 10 3. Game Volume = 10 4. Voice Output = Play Through Headset 8 Connecting a Digital Music Player The X32 features an auxiliary input for connecting digital music players or other analog sources so you can listen to your own music along with the game audio. The Auxiliary Input volume can be adjusted directly from the digital music player. D N A L B A U D LINE IN AUX IN Auxiliary Input Connect the digital music player to the Auxiliary Input if you want to hear the music along with the game audio. 3.5mm Cable

(sold separately) Digital Music Player 9 Connecting a DSS or DSS2 The X32 can be upgraded to Dolby Digital surround sound by adding the Ear Force DSS or DSS2 surround sound processors

(sold separately). Visit www.turtlebeach.com/DSS2 to learn how you can upgrade your X32 headset with surround sound. X32 Stereo Sound Field Add a DSS or DSS2 to Upgrade to Surround Sound X32 Sound Field with Dolby Digital Surround Sound Processing Setup 3.5mm Cable

(included with DSS2) USB Power Cable

(included with DSS2) Digital Optical

(included with Cable DSS2) Transmitter USB Cable*

*Both the X32 transmitter USB cable and the DSS/DSS2 USB power cable must be plugged into separate USB ports directly on the Xbox 360 console for power. Do not plug the transmitter USB cable into the USB OUT port on the DSS or DSS2, as this may cause overloading of the USB ports. 10 Tone (EQ) Presets The X32 features multiple Equalizer presets to enhance your gaming audio experience. Press the TONE button on the X32 headset to cycle through the EQ presets as illustrated below:

Equalizer (EQ) Presets:

1. Flat 2. Bass Boost 3. Treble Boost 4. Bass and Treble Boost Tone Button T O N E Effects (Sound Field Expander) Presets The Sound Field Expander improves your ability to hear sounds coming from a distance by boosting sounds on the left and right sides and lowering sounds in the center. Press the EFFECTS button to cycle through the three settings as illustrated below:

Tone (Sound Field Expander) Presets:

1. Normal 2. Narrow 3. Wide 11 Effects Button Chat Boost Chat Boost is a dynamic talkback expander built into the X32 headset that automatically increases chat volume during loud moments in your game, so you can always hear your teammates or other players, regardless of the game volume. Typically, if you turn up a headsets game volume, the incoming chat level from other players could become difcult to hear over the game sound. However, with Chat Boost, as the game audio increases, the chat volume also increases. When the game volume quiets down again, Chat Boost automatically returns the chat level to your original volume setting. To properly set the Chat Boost function:

1. Turn down the volume control on the headset so theres no game audio. 2. Adjust the volume control on the talkback cable so you can hear the chat voices at a comfortable level. 3. Turn up the headset game volume and the chat volume will increase whenever the game gets louder, just as if the talkback volume control is being automatically turned up along with the game level. Note that if the volume on the talkback cable is set too loud, Chat Boost might increase the volume so much that the voices will distort. If that happens, turn down the talkback volume on the talkback cable. WITHOUT Chat Boost, chat volume is overwhelmed by loud game audio WITH Chat Boost, chat volume increases along with game volume, so you can always hear teammates NOTE: If the volume on the talkback cable is set too loud, Chat Boost might increase the volume so much that the voices will distort. If that happens, turn down the talkback volume on the talkback cable. 12 X32 Headset Technical Specications 50mm diameter speakers with neodymium magnets Game audio frequency response: 20Hz - 20kHz, >120dB SPL @ 1kHz Condenser microphone frequency response: 50Hz - 15kHz Game audio Dual Band WiFi Digital 2.4GHz/5.8GHz RF wireless reception Headphone amplier: Stereo 27mW/ch, THD <1%

Operates on (2) AAA batteries or (2) AAA rechargeable NiMH batteries Automatic shut down after approx 5 minutes of carrier loss or audio silence to conserve battery power Battery booster circuit extends battery life for up to 15 hours X32 Transmitter Technical Specications Dual Band WiFi Digital 2.4GHz/5.8GHz RF wireless transmission with up to 30 foot range Frequency response: 20Hz - 20kHz Stereo 3.5mm line input jack Stereo 3.5mm aux input jack Maximum analog input level: 2Vpp (700mV rms) USB Power (5V DC @ 180mA max) 13 Troubleshooting No sound

communicating with the headset. If the headset is on solid and the transmitter LED is slowly pulsing, then the headset and transmitter need to be paired as described in the section Pairing the Headset and Transmitter. Audio Drops, Popping or Clicking Sounds Audio dropouts, popping or clicking sounds on the headset are caused by poor reception. This can occur when:

Voice Chat Drops

please be patient. In extreme cases, you may have to leave a game and return to reset the chat function.

A wired connection from your modem/router to your console is recommended for best results. Safety Notice To avoid potential damage to the device, always disconnect all cables before transporting it. WARNING: Permanent hearing damage can occur if a headset is used at high volumes for extended periods of time, so it is important to keep the volume at a safe level. Over time, your ears adapt to loud volume levels, so a level that may not cause initial discomfort can still damage your hearing. If you experience ringing in your ears after listening with the headset, it means the volume is set too loud. The louder the volume is set, the less time it takes to affect your hearing. So, please take care to listen at moderate levels.

then slowly increase it to a comfortable level.

14 Manufacturer:

Manufacturers Address:

Product Name:

Type of Product:

Model Number(s):

Year of Manufacture:

Voyetra Turtle Beach 150 Clearbrook Rd. Suite 162, Elmsford, NY 10523 Ear Force X32 Wireless Headset TBS-2265-01 2011 We, Voyetra Turtle Beach, Inc. of Elmsford, New York, declare under our own responsibility that the above-referenced product complies with the following directives and standards:

Low Voltage Directive 2006/95/EC EN 50332-2:2003 EN 60950-1:2006+A11:2009 Electromagnetic Compatibility Directive 1999/5/EC ESTI EN 301 489-1 V1.8.1 (2008) ESTI EN 301 489-3 V1.4.1 (2002) ESTI EN 301 489-17 V2.1.1 (2009) R&TTE Directive 1999/5/EC ESTI EN 300 328 V1.7.1 (2006-10) ESTI EN 300 440-1 V1.4.1 (2008-05) ESTI EN 300 440-2 V1.2.1 (2008-05) All test reports have been reviewed and approved with a Positive Opinion from the following Notied Bodies:

Bay Area Compliance Laboratories, Corp (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone, Shenzhen, Guangdong, China Tel: +86-755-33320018, Fax: +86-755-33320008, Web: baclcorp.com Shenzhen EBO Technology Co., Ltd. No. 710 Yihua Building, Futian District, Shenzhen, China 518040 Tel: +86-755-29451282 Fax: 86-755-83709189 Web: ebotek.cn The technical documentation required by this Directive is maintained at the corporate headquarters of Voyetra Turtle Beach, 150 Clearbrook Road. Suite 162, Elmsford, New York, 10562. Authorized Person:

____________________________ ____________ __________________ ________________________ Printed Name: Frederick Romano Title: Executive Vice President Date:________________ 11/17/11 15 Product Name:

Model Number(s):

FCC Rules:

Ear Force X32 TBS-2265-01 FCC CFR Title 47 Part 15 Subpart B: 2009 CLASS B FCC CFR Title 47 Part 15 Subpart C: 2008 Operating Environment: GENERAL OFFICE AND HOME USE FCC COMPLIANT STATEMENT This device complies with part 15 of the FCC rules. Operation is subjected to the following conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received including interference that may cause undesired operation. INFORMATION TO USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. The users manual or instruction manual for an intention or unintentional radiator shall caution the user that the changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. WARNING: Changes or modications made to this equipment not expressly approved by VOYETRA TURTLE BEACH, INC. may void users authority to operate this equipment. 16 Limited Warranty for Turtle Beach Products Voyetra Turtle Beach, Inc. ("VTB") warrants to the original end-user purchaser ("Purchaser") that the retail Turtle Beach hardware product herein ("Product") will be free of defects in materials and workmanship for a period of one year from the date of purchase by the Purchaser

("Warranty Period"). Any Extended Warranty or Service Plans purchased through a Retail store are not honored by VTB. The Warranty refers to the repair/replacement of a defective product during this period and not a refund. This limited warranty extends only to the Purchaser and is not transferable or assignable to any subsequent purchaser. This limited war-

ranty is applicable only in the country or territory where the Product was purchased from an authorized VTB retailer and does not apply to a Product that has been purchased as used or refurbished (except refurbished by VTB) or was included as part of a non-VTB product. WARRANTY SERVICE In the USA and CANADA Warranty Service is provided by our TURTLE BEACH OFFICEs and in all other Countries it is provided by our local International Distributors. VTB does not warrant uninterrupted or error-free operation of the Product and is under no obligation to support the Product for all com-

puter operating systems or future versions of such operating systems. If a defect should occur during the Warranty Period, Purchaser must contact VTB to obtain a Return Merchandise Authorization ("RMA") number. Purchaser will be responsible for shipping costs incurred in returning the defective Product to an authorized VTB service center, or to the repair facility located at VTB's corporate headquarters. A copy of the dated proof of purchase and a description of the problem must be included with the defective Product. VTB will not be responsible for other products or accessories included with the defective Product sent to VTB. The RMA number must be clearly indicated on the outside of the package. Packages without an RMA number will be refused by VTB or its representatives and returned to sender at the sender's expense. In the event of a defect, Purchaser's sole and exclusive remedy, and VTB's sole liability, is expressly limited to the correction of the defect by adjustment, repair, or replacement of the Product at VTB's sole option and expense. VTB owns all Products it has replaced and all parts removed from repaired Products. VTB uses new and reconditioned parts made by various manufacturers in performing warranty repairs and building replacement products. If VTB repairs or replaces a product, the original Warranty Period is not extended, however, VTB war-

rants that repaired or replacement parts will be free from defects in material and workmanship for a period of thirty (30) days from the date of repair or replacement, or for the remainder of the Warranty Period, whichever is greater. This warranty does not apply to any Product that has had its serial number altered, removed or defaced, or any Product damage caused by shipping, improper storage, accident, problems with electrical power, abuse, misuse, neglect, ordinary wear, acts of God (e.g. ood), failure to follow directions, improper maintenance, use not in accordance with product instructions, unauthorized modication or service of the Product or damage resulting from the use of the Product with hardware, software or other products not provided by or specically recommended by VTB. 17 THIS LIMITED WARRANTY IS PURCHASER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. TO THE EXTENT PERMITTED BY APPLICABLE LAW, VTB HEREBY DISCLAIMS THE APPLICABILITY OF ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR USE FOR THE PRODUCT. IF SUCH A DISCLAIMER IS PROHIBITED BY APPLICABLE LAW, THE IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY. IN NO EVENT SHALL VTB BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, OR DAM-

AGES, INCLUDING BUT NOT LIMITED TO ANY LOST PROFITS, DATA, OR LOSS OF USE, ANY THIRD PARTY CLAIMS, AND ANY INJURY TO PROPERTY OR BODILY INJURY (INCLUDING DEATH) TO ANY PERSON, ARISING FROM OR RELATING TO THE USE OF THIS PRODUCT OR ARISING FROM BREACH OF THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, TORT, OR STRICT LIABILITY, EVEN IF VTB HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This warranty supersedes all prior agreements or understandings, oral or written, relating to the Product, and no representation, promise or condition not contained herein will modify these terms. Some states do not allow the exclusion or limitation of incidental or consequen-

tial damages, so the above exclusion or limitation may not apply to you. This warranty gives you specic legal rights. You may also have other rights, which vary from state to state. Any action or lawsuit for breach of warranty must be commenced within eighteen (18) months following the purchase of the Product. EXCLUSIONS FROM LIMITED WARRANTY:

This Limited Warranty shall not apply and VTB has no liability under this Limited Warranty if the Turtle Beach Product:

18 Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help. FCC Caution:

Any changes or modications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF Exposure Warning:

Headset:

The equipment complies with FCC RF exposure limits set forth for an uncontrolled environ-

ment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. Transmitter Box:

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. CANADA, INDUSTRY CANADA (IC) NOTICES This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information:

Headset:

The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. (antennas are less than 20 cm of a person's body). Transmitter:

The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). This device has been certied for use in Canada. Status of the listing in the Industry Canada's REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/

app/sitt/reltel/srch/nwRdSrch.do?lang=eng Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Canada, avis d'Industry Canada (IC) Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210.Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. Informations concernant l'exposition aux frquences radio (RF) Headset:

La puissance de sortie mise par l'appareil de sans l Dell est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez l'appareil de sans l Dell de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils portables (les antennes sont moins de 20 cm du corps d'une personne). Transmitter:

La puissance de sortie mise par l'appareil de sans l Dell est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez l'appareil de sans l Dell de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils mobiles (les antennes se situent moins de 20 cm du corps d'une personne). Ce priphrique est homologu pour l'utilisation au Canada. Pour consulter l'entre corre-

spondant l'appareil dans la liste d'quipement radio (REL - Radio Equipment List) d'Industry Canada rendez-vous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Pour des informations supplmentaires concernant l'exposition aux RF au Canada rendez-

vous sur:http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html This product is CE marked according to the provisions of the Low Voltage Directive (2006/95/

EC), R&TTE Directive (1999/5/EC) and EMC Directive (1999/5/EC). Frequency Range: 2.404-2.476GHz / 5.160-5.340GHz

IC: 3879A-2265 IC: 3879A-2266 DESIGNED AND ENGINEERED BY TURTLE BEACH IN NEW YORK, USA Copyright 2012 Voyetra Turtle Beach, Inc. (VTB, Inc.) All rights reserved. No part of this guide may be reproduced without permission. Turtle Beach, the Turtle Beach Logo, Voyetra, Ear Force, Chat Boost, Engineered For Gaming and the Dual Band logo are either trademarks or registered trademarks of VTB, Inc. XBOX, XBOX 360 and XBOX LIVE are registered trademarks of Microsoft Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories. All other trademarks are properties of their respective companies and are hereby acknowledged. Assembled in China. PATENTS PENDING 19 For more products, accessories and general product information, please visit TurtleBeach.com For warranty information and product support, please visit TurtleBeach.com/support 20 B 1 0

-

5 6 2 2

-

0 2 1 B T 21212121

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT Cover off View EUT Main Board Top View Antenna 0 Antenna 1 EUT Main Board Bottom View

EUT Front View EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT Rear View

EXHIBIT A - FCC ID LABELING AND LOCATION FCC ID Label FCC ID Label Location Label here The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Picture 1 X32 Headset Block Diagram Picture 2 X32 Transmitter Block Diagram Page 1 of 1 1/18/2012

Descriptionoffunctionalblocks X32/X42RX 1WIFImodule WIFImodulecontainsOZMO2000with24MHz externalCrystalOscillatorand2.4GHzand4.95.875 GHzChipAntenna.TheOZMO2000isfullyintegratedradio,baseband,andlogicSystemonChip(SoC) bringingWiFiCERTIFIEDWiFiDirecttechnologytocostandpowersensitiveperipheraldevices.It offershigherdatarates,moreextensiveapplicationinterfaces,additionalmemory,hardwarecrypto accelerators,anintegratedpoweramplifier,anaudioPLLandalowpowerRCOsleeptimer.Its dualbandradiodesignallowsseamlessinteroperabilitywithOzmoenabledIEEE802.11a/b/ghosts. 2BatterysupplypowerforthewholeproductandthePowerofOZMO2000andFlashMemoryis 1.9V. 3Buttonandvolumeistheuserinterface. X32TX 1WIFImodule WIFImodulecontainsOZMO2000with24MHzexternalCrystalOscillatorand2.4GHzand4.95.875 GHzChipAntenna.Itfullyintegratedradio,baseband,andlogicSystemonChip(SoC)bringingWiFi CERTIFIEDWiFiDirecttechnologytocostandpowersensitiveperipheraldevices.Itoffershigher datarates,moreextensiveapplicationinterfaces,additionalmemory,hardwarecryptoaccelerators, anintegratedpoweramplifier,anaudioPLLandalowpowerRCOsleeptimer.Itsdualbandradio designallowsseamlessinteroperabilitywithOzmoenabledIEEE802.11a/b/ghosts. 2ThepowersupplyistheexternalUSBandthePowerofOZMO2000andFlashMemoryis3.3V. 3Buttonistheuserinterface. X42TX WIFImodule 1TheWIFImodulecontainsasinglechip(OZMO2000)with24MHzexternalCrystalOscillatorand2.4 GHz and 4.95.875 GHz Chip Antenna. It fully integrated radio, baseband, and logic SystemonChip

(SoC) bringing WiFi CERTIFIED WiFi Direct technology to cost and power sensitive peripheral devices. It offers higher data rates, more extensive application interfaces, additional memory, hardwarecryptoaccelerators,anintegratedpoweramplifier,anaudioPLLandalowpowerRCOsleep timer.ItsdualbandradiodesignallowsseamlessinteroperabilitywithOzmoenabledIEEE802.11a/b/g hosts. 2DSPmodule TheDSPmoduleisaCosteffective,Highperformance32bitDSPwith24.576MHzexternalCrystal Oscillator,itIntegratesDAC&ADCFunctionality,SupportsDifferentFsSample,haveConfigurable SerialAudioInputs/Outputs,HostControl&BootviaI2CorSPISerialInterfaceandConfigurable GPIOsandExternalInterruptInput. 3ThepowersupplyistheexternalUSBandthePowerofOZMO2000andFlashMemoryis3.3V. 4Buttonistheuserinterface.

1 Volume D5 PESD5V0S1BB 1 F p 2 2 6 C F u 1

. 0 8 2 C 2 F p 2 2 0 7 C F u 1

. 0 1 7 C

+VBUCK R57 18K 1%

RT1 10K LIN A R55 3K 1%

3 5 4 2 2 C3 0.1uF 1

+VBATT R58 499K 1%

R7 316K 1%

C1 0.1uF Y1 24MHz C14 8.2pF C18 8.2pF BATT_SENSE GAME_VOL 3 F u 1

. 0 2 7 C 0 1 1 1 8 1 7 3 2 3 6 2 5 4 2 5 F u 1

. 0 3 7 C F u 1

. 0 4 7 C F u 1

. 0 5 7 C 3 T T A B V 1 T T A B V 2 T T A B V I I I I O D D V O D D V O D D V O D D V O D D V I RST_N RF2P4N SW3

+VBOOST TP5 D13 D1 POWER R87 150R R10 150R 19 20 6 5 4 3 29 28 27 40 35 34 33 31 30 53 46 51 50 49 48 44 12 15 XOIN XOCAP T1 T2 T3 T4 AIO0 AIO1 AIO2 AIO7 AIO11 AIO12 AIO13 AIO14 AIO15 AUXO VDDD U7 OZMO2000 S S V 7 5 RF2P4P RF5N RF5P TSTMODE TSTSEL0 TSTSEL1 TDI AIO6 AIO5 TDO TMS TCK TSTCLK VDD_PA VDDA_AN EXTR SPIBOOTCS SPICLK SPIMISO SPIMOSI VDDRET VDDA_RF VDDA_LO K L C O D U A I 4 O A 3 O A 8 O A 9 O A I I I I 0 1 O A I 54 13 14 8 7 21 23 24 56 41 42 1 2 55 25 9 17 16 TP19 BEEP LED TP20 MFB EQ_SW FX_SW PW_HOLD DAC_PDN AUDIO_DET AUXO C82 1uF 1 6 2 5 SPI_CE#

SPI_CLK SPI_SO SPI_SI C87

.01uF C88

.01uF

+VBUCK U5 8 7 3 4 SST25WF010-40-51-SAF VDD HOLD WP#

VSS CE#

SCK SO SI C42 22pF VOZMO

+

C81 220uF 4 L1 10uH

+VBUCK D16 RB521S-30

+VLDO A1 FR05-S1-NO-1-004 2 1 C95 1.5pF F u 1

. 0 6 7 C FR05-S1-NO-1-004 A2 2 C96 1 1.5pF C17 TBD C13 TBD C93 TBD C94 TBD U8 ANT C N 1 V 2 V G 1 5 2 7 3 RX 4 TX SKY13314-374LF F1 LDB182G4510G-120 BAL GND BAL NC GND UNBAL F2 LDB185G3710G-120 BAL GND BAL UNBAL GND NC 6 5 1 1 5 6 R3 140K 1%

VOZMO C7 0.1uF 4 2 3 3 2 4 C16 NU C12 NU C9 5.6pF C15 5.6pF C10 1.5pF C11 1.5pF TESTSEL1 TDI UART_RX UART_TX TDO TMS TCK U2 LFD182G45DP4B889 IN1 COM 3 IN2 G 2 4 C92 1.5pF 1 AUXO 6 4 3 6 1 PW_HOLD VOZMO R62 20K R1 20K C99 0.1uF Q1 BC847BT C85 4.7uF D2 1SS400 SW2 3 1 4 2 Power U9 Y2 A2 Y1 A1 VCC GND 5 2 NC7WZ04P6X 5 JP5 BATTERY 1 2 Battery R88 0R NU

+VBATT R64 560K C2 100uF/10V/Tan

+VBATT

+

6 TP2

+VBOOST 3.2VD TP1 L6 4.7uH 1 U6 MCP1640 6 3 VIN EN W S D N G Vo B F 2 4 5 1 5 R

%

1 K 4 3 5 C40 4.7uF R66 10K Q2 AO3423 C63 0.1uF R59 324K 1%

+VBUCK R65 220K C78 10uF C79 0.1uF C36 47uF A C5 1uF TP17 C21 0.1uF R56 140K 1%

TP18

+VBUCK JP4 DEBUG 1 3 5 7 9 2 4 6 8 10 TDO TMS TESTSEL1 TCK R4 NU Test C8 0.1uF

+VLDO

+VBUCK C83 0.01uF R54 0R R15 10R

+VBUCK C19 0.1uF C22 10uF 5 1 1 2 6 4 I2SMCK I2SDATA I2SLRCK I2SBCK I2CCK I2CDATA DAC_PDN C30 1uF R22 6K8 17 11 13 14 18 9 10 7 8 25 5 27 26 R23 20K Mic In C34 0.1uF 1 2 MIC IN JP3 C33 0.22uF C 2 I D D V D D D V H D D V A MCKI SDTI LRCLK BICK MCKO SCL SDA PDN CSN MUTET 3 7 3 4 K A VCOC LOUT ROUT 1 S S V 2 S S V 3 S S V 3 2 2 6 1 C51 0.1uF C20 0.1uF C23 4.7uF VCOM 2 24 23 HPL HPR 19 20 29 28 1 12 30 32 31 SPN SPP MIN-

MIN+

NC NC NC NC NC U3 AK4373 C24 4.7uF C27 0.1uF HP L HP R MONO OUT CHAT MIC MON R36 10K MFB D4 1SS400 TP6 L2 4.7uH 5 VIN EN W S D N G 4 Vo MCP1603 2

+VBUCK 1.9V TP3 0 9 R

%

1 K 0 0 2 2 9 R

%

1 K 9 9

. 4 C50 10uF C91 33p R91 147K 1%

+VBOOST U1 1 3 1 D7 C86 4.7uF 2 C25 330uF

+

TP15

+

C29 330uF 2 1 TP14 JP1 1 2 SPK_L JP2 2 1 SPK_R TP16 D10

+VBOOST 1 3 U4 TC1187 Vin EN D N G Vo FB 5 4 C55 4.7uF 2 R29 680K 1%

2.8V

+VLDO TP7 C56 10uF

+VLDO R80 20K R2 511K 1%

TP12 TP13 CHAT R46 4K7 R25 47K VREF F u 7 4

. 0 4 4 C F u 7 4

. 0 3 5 C F u 7 4

. 0 4 5 C

+VLDO K 0 1 0 7 R

+VLDO 7 6 R 7 K 2

+VLDO 8 6 R 6 K 3

+VLDO K 0 2 9 6 R R61 1M C52 0.001uF R81 BEEP 10K Q24 BC847BT C58 4.7uF

+VLDO R77 4K7 6 5 3 T U O O N O M C35 0.47uF R35 33K 2

+VLDO

+VLDO

+VLDO R24 2K7 R28 20K Q9 BC857BT 150mV w No Input Signal R42 4K7 R32 10K R27 3K6 6 5 3 Q7 BC847BS 1 4 R45 220K C47 220pF C45 4.7uF R49 1K 0.6V R48 4K7 VREF

+VLDO Q10 BC847BT 0.36V - 2.2V Q12 BC857BT R41 4K7 R44 33K C49 0.039uF C46 10uF R52 1M VREF Q15 FDN338 Q16 BC857BT R86 4K7 R50 47K R85 470K 0.75V - 1.6V R43 4K7

+VLDO 2 7 R K 3 3 3 7 R K 3 3 Q18 BC847BT C68 0.47uF R83 470K 2 C65 10pF R84 2K7 Q20 BC857BT 2 Q22 BC847BS 6 5 3 R74 47K 1 4 1 C59 0.0047uF Title R75 220K C4 100pF C60 4.7uF R19 220R R76 5K1 4 Q21 BC847BS AUDIO_DET R71 20K LOW = AUDIO ON HIGH = NO AUDIO NOTE: Do not populate components marked as NU 1 of X32 RF Headset 2011-11-28 1 Date:

Sheet X32 RF Rx SCH_20111128.SchDoc TB400-1164-R5 CONFIDENTIAL DOCUMENT

(c) 2011 Voyetra Turtle Beach, Inc. DO NOT COPY OR DISTRIBUTE WITHOUT WRITTEN PERMISSION FROM VTB, INC. Revision:

ES2.1 VOYETRA TURTLE BEACH, INC 150 Clearbrook Road, Elmsford, NY 10523

(914) 345-2255 www.TurtleBeach.com 1 2 3 4 5 6 3 4 7 4 9 3 8 3 6 3 2 2

+VBUCK R8 R11 10K 10K

+VLDO R21 2K7 3 65 Q6 BC847BS 2 1.6V R9 R12 R13 R14 56R 56R 56R 56R C62 22pF TP9 4 1 C66 0.47uF R18 200K R39 150K C67 0.1uF R5 20K R63 20K R20 2K7 C80 100pF 2 R47 4K7 1 R82 47K Q4 BC847BT C41 1uF TBK

+VLDO R60 47K VREF R30 10K R26 47K R31 10K C37 0.01uF C69 0.0047uF Q5 BC857BT D11 PESD5V0S1BB

+VLDO C64 10pF Q8 BC847BT C39 0.47uF R40 2K2 R34 2K VREF 2 4 2 4 SW1 1 3 1 3 EQ TP4 FX EQ FX 2 2 1D8 1D3 C43 0.1uF

+VLDO 2.8V R17 10K 2 C38 4.7uF 1 2.2V 6 5 3 Q3 BC847BS TP8 1.6V 4 VREF C26 4.7uF C48 10uF D9 PESD5V0S1BB 2 L7 1 1 2 3 TP10 TP11 J1 JACK 2.5MM Controller 1 D12 PESD5V0S1BB 2 R37 2K7 L4 C31 220pF C32 220pF L5 B C D B C D