FCC ID: EW780-2813-00 Video Monitor - Baby Unit

Full Color Video Monitor Full Color Video Monitor LF2423 LF2423-2 Whats Included 2. Charge the Parent Viewer Battery 4. Status Check Important Safety Instructions The applied nameplate is located at the bottom of the Baby Units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the Baby Unit at a height above 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the Parent Viewer. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Power adapter information:

Baby Unit Output: 5V DC 600mA;

VTech Telecommunications Ltd.; Model: VT05EUS05060 /

VT05EEU05060 / VT05EUK05060 Parent Viewer Output: 5V DC 1000mA;

VTech Telecommunications Ltd.; Model: VT05EUS05100 /

VT05EEU05100 / VT05EUK05100 Rechargeable battery information:

Zhongshan Tianmao Battery Co. Ltd Li-ion battery, 3.8V 2100mAh 7.98Wh; Model: BP1763 8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. 11. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. Do not overload wall outlets or use an extension cord. 15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 19. You should test the sound reception every time you turn on the units or move one of the components. 20. Periodically examine all components for damage. 21. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 22. Children should be supervised to ensure that they do not play with the product. 23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between 32oF

(0oC) and 104oF (40oC). 2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire. 4. WarningStrangulation HazardChildren have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. 5. Never place the Baby Unit(s) inside the babys crib or playpen. Never cover the Baby Unit(s) or Parent Viewer with anything such as a towel or a blanket. 6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This LeapFrog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. Parent Guide This guide contains important information. Please keep it for future reference. Need help?

Visit leapfrog.com/support Visit our website leapfrog.com leapfrog.com for more information about products, downloads, resources and more. Read our complete warranty policy online at leapfrog.com/warranty. Scan the QR code to enter our Online Manual:

Or go to leapfrog.zendesk.com/hc Touch a nd learn!

Touch a nd learn!

CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1 Notes:

Parent Guide Before using the baby monitor for the first time, charge the Parent Viewer battery for 12

. hours. When the Parent Viewer battery is fully charged, the battery icon becomes solid The standby time varies depending on your actual usage time and the age of the battery. Once your Baby Unit and Parent Viewer are powered on and connected, your Parent Viewer displays video from Baby Unit, and the LINK LED light turns on. The battery icon on the screen indicates the battery status:

5. Positioning the Baby Monitor Battery Indicators Battery Status Action The screen displays light flashes. The

. The battery is low in power and may only be used for a short time. Charge without interruption

(about 30 minutes). The battery icon becomes solid

. The battery is fully charged. To keep the battery charged, connect it to AC power when not in use. 1 set for LF2423 2 sets for LF2423-2 1 3 Caution:

Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the babys crib or playpen. 2 Manual Tilt 4 3ft (1m)

< 3ft (1m) Note:

To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers. Caution:

The default volume of your Parent Viewer is level 3, and the maximum volume is level 5. If you experience a screeching noise from your baby monitor while positioning:

- Make sure your Baby Unit and Parent Viewer are more than 3 feet (1 meter) apart, OR

- Lower the volume of your Parent Viewer. Connect and Charge the Baby Monitor 1. Connect the Baby Monitor Note:

Baby Unit turns on automatically after it connects to the power socket. 3. Power On or Off the Baby Monitor Connect the power adapter to the Baby Unit and a power supply to power on the unit. Disconnect from the power supply to power off. Press and hold screen appears. until the welcome Press and hold Overview Parent Viewer 1 2 3 4 Link LED light Power /

LCD Off Menu / Select Volume View the volume adjustment bar. Arrow keys Baby Unit 1 2 3 4 5 1 2 3 4 5 1 2 3 4 1 2 3 4 5 1 2 3 4 6 7 Battery LED light 11 Power jack 8 5 6 7 Talk /

Return 7 Microphone 5 6 8 9 RESET Stand 10 Speaker 7 8 9 8 9 6 6 6 7 8 9 7 8 9 10 Light sensor Camera lens Infrared LEDs Night light 5 Microphone Power jack Speaker PAIR key The Parent Viewer and Baby Unit(s) provided are already paired Night light control key Press to turn the night light on or off. 10 Slots for wall mounting The RBRC seal The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY are registered trademarks of Call2recycle, Inc. 9 10 11 California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the Parent Viewer is paired to Baby Units, the CEC battery charging testing mode is activated while it is powered off and charging. For cETL compliance only Mesures de scurit importantes La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. 2. Linstallation par un adulte est requise. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilit du parent ou de la personne qui soccupe de lenfant. Ce produit pourrait cesser de fonctionner et, par consquent, vous ne devriez pas prsumer quil continuera de fonctionner correctement pendant une priode de temps donne. De plus, il ne sagit pas dun instrument mdical et ne devrait pas tre utilis comme tel. Ce produit est destin vous aider superviser votre bb. 5. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque dexplosion pourrait survenir si un mauvais type de pile est utilis pour lunit du parent. La pile ne peut pas tre soumise des tempratures extrmes leves ou basses et une faible pression dair haute altitude pendant lutilisation, lentreposage ou le transport. Llimination de la pile dans le feu ou dans un four chaud, ou lcrasement ou le dcoupage mcanique de la pile peuvent entraner une explosion. Laisser la pile dans un environnement temprature extrmement leve peut entraner une explosion ou la fuite dun liquide ou dun gaz inflammable. Une pile soumise une pression dair extrmement basse peut provoquer une explosion ou une fuite de liquide ou de gaz inflammable. liminer la pile usage conformment aux informations du Sceau RBRC. 7. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et Online Manual Find the answer to your question on our knowledge-rich Online Manual. Get assisted at your own pace and learn what your monitor is capable of. Scan the QR code to access the Online Manual or visit leapfrog.zendesk.com/hc Disclaimer and Limitation of Liability LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. LeapFrog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect against data loss. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-3 (B)/NMB-3(B) Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Warranty: Please visit our website at leapfrog.com for full details of the warranty provided in your country. 10 10 Increase the separation between the equipment and receiver. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The Baby Unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the Parent Viewer shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The Baby Unit should be installed and operated with a minimum distance of 8 in (20 cm) between the Baby Unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. mettre votre scurit en pril. Informations sur les adaptateurs lectriques :

Adaptateur de lunit du parent : Sortie : 5V DC 600mA VTech Telecommunications Ltd. Modle: VT05EUS05060 / VT05EEU05060 / VT05EUK05060 Adaptateur de lunit du bb : Sortie : 5V DC 1000mA VTech Telecommunications Ltd. Modle: VT05EUS05100 / VT05EEU05100 / VT05EUK05100 Informations sur les piles rechargeables :

Zhongshan Tianmao Battery Co. Ltd Li-ion battery, 3.8V 2100mAh 7.98Wh;

Modle: BP1763 8. Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. 9. Pour les PRODUITS BRANCHER UNE PRISE DE COURANT, la prise de courant doit tre installe prs du produit, afin dassurer une accessibilit scuritaire la prise de courant. 10. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 11. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. 12. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 13. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 14. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. 15. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 16. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouver-

tures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 17. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 18. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 19. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 20. Examinez les composantes afin de vrifier si celles-ci ne sont pas endommages. 21. Il existe un trs faible risque de perte de confidentialit avec certains appareils lectroniques (autres coute-bbs, tlphones sans fils etc.). Pour lviter, sassurer que le produit na jamais t utilis avant lachat, rinitialiser lunit de faon priodique, teindre lcoute-bb quand il nest pas en cours dutilisation. 22. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. 23. Le produit nest pas conu pour tre utilis par des personnes (incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. Mises en garde 1. Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). 2. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. 3. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu0. CONSERVEZ CES INSTRUCTIONS 4. Avertissement - Risque de strangulation - Les enfants se sont TRANGLS dans des cordons. Gardez ce cordon hors de porte des enfants ( plus de 0,9 m). 5. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une Nenlevez pas cette tiquette. couverture. 6. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil) :

Lorganisme Wireless Technology Research, LLC (WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de LeapFrog est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. Full Manual Comprehensive help articles on product set up, operations and settings. Video Tutorials FAQs & Troubleshooting Walk-throughs on features and installation. Answers to the most commonly asked questions, including troubleshooting solutions. Customer Support Visit our Consumer Support website 24 hours a day at:

United States:

leapfrog.com/support Canada:

leapfrog.ca/support Call our Customer Service number from Monday to Friday 9am - 6pm Central Time:

United States & Canada:

1 (800) 701-5327 Warranty Please visit our website at leapfrog.com for full details of the warranty provided in your country. Technical Specifications Frequency Control Crystal controlled PLL synthesizer Channels 32 Frequency Baby unit: 2405 - 2475 MHz Parent unit: 2405 - 2475 MHz LCD 2.8 Color LCD (QVGA 320x240 pixel) Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirements Parent unit: 3.8V, 2100mAh Li-ion, 7.98Wh Li-ion battery Baby unit power adapter: Output: 5V DC @ 600mA Parent unit power adapter: Output: 5V DC @ 1A Specifications are subject to change without notice. 2022 LeapFrog Enterprises, Inc. a subsidiary of VTech Holdings Limited. All rights reserved. 01/22. LF2423_QSG_V1

BU LABEL SIZE: 29.5X36.5 mm 50# UL Approved PET MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 FCC ID: EW780-2813-00 IC: 1135B-80281300 HVIN: 35-201673BU FCC ID: EW780-2813-00 IC: 1135B-80281300 HVIN: 35-201673BU MANUFACTURED IN CHINA Leapfrog customer service 1-800-701-5327 FCC ID: EW780-2813-00 IC: 1135B-80281300 HVIN: 35-201673BU A/V I.C.T.E. A/V I.C.T.E. Model: LF2423-2 BU Model: LF2423 BU A/V I.C.T.E. Model: LF2423 BU S/N: XXXXXXXXXXX S/N: XXXXXXXXXXX S/N: XXXXXXXXXXX 7.14mm A/V I.C.T.E.

VTech Telecommunications Ltd Feb 28, 2022 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 15 Certification FCC ID: EW780-2813-00 Request is hereby submitted by VTech Telecommunications Ltd. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and VTech Telecommunications Ltd. reserves the right to discern which parties can obtain access to these information:

Schematics Detailed Block diagrams Detailed Operational/Functional Description The rationale for request for confidentiality is as followings:

This information represents intellectual property of VTech Telecommunications Ltd. and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Appendix B1 Letter of Agency for FCC Certification Sep. 27, 2017 To whom it may concern, Letter of Agency I, an officer of VTech Telecommunications Ltd do hereby authorize Intertek Testing Services (Terry Chan/ Koo Wai Ip/ Kenneth Wong/ Jess Tang) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in 1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Michael Tsui Approbation Supervisor