LA A PAYMEN NT DEVICE XCL_AP X P-10 INST TALLATIO ON GUIDE E d 1. PACKAGE CONTENT 2. DEVICE OVERVIEW
xCL_AP-10
Privacy Shield (Optional) xCL_AP10(hereundercalledAP10)KeyButtons&InterfacePorts(Figure1):
FRONT REAR FRONTAREA Figure1 1 2 3 4 TFT Color Display (480 x 800 pixel) Rubber Keypad Smart Card Reader (SCR) slot 4 Magnetic Strip Reader (MSR) slot REARAREA 5 6 USB cable (type A) SAM Compartment AP-10 power spec:
PowerInput:5VDC,2Aor5VDC,1A(onlyforDUALUSBA) OperatingTemperature:0oCto40oC
WA RNING:
1.The equipmentis training or experien energiesandenergy 2.Theequipmentis port that thatoutpu 609501/EN60590 C Caution:UseonlytheAC sintendedtobeinstall nce in the equipment magnitudesusedinthe intendedtobesupplied utcomplies with the re 1/UL605901/CSA60 Cadapterapprovedand edbyskilledpersonor technology, particularl eequipmentandhostde dbyahostdevice(PCo equirement of the Lim 09501 providedbyXACAutom ave ous rserviceperson whoha y in knowing the vario evice. orterminaldevice)viaU ited Power Source of USB IEC mationCorporationforu use withthisdevice C Caution:Riskofexplosio batteryaccording onifthebatteryisrepla gtotheinstructions. acedbyanincorrecttyp pe.Pleasedisposeofus sed 3. POWER R ON/OFF THE D DEVICE To powe terminal r on the device, ple orPOS. ase plug the USB ca able type A into the USB port of your ho ost Note:Aft pow terbootingupAP10, wersavingmode.Plea ifisnoactiononAP aseshortpressanyb 10after60seconds, uttononkeypadtow thedevicewillenter wakeupthedevice. 4. USING T THE MAGNETIC R CARD READER Swipe th display.(
e card through the s Figure2) slot with magnetic s stripe side facing the e same direction as t the Figure2 5. USING THE IC CARD READER InsertanICcardintotheslot(Figure3)withthechipsidefacingupwardasthedisplay(Figure 4). Figure3 Figure4 6. USING THE KEY PAD Afterinsertingthechipcard,Pressthenumerickeyasbelowkeypad(Figure5)toenterthe desirablenumbers.PressCancel(X)keytoterminateanycurrentoperationorpresstheEnter
(O)keytoconfirmavalueoranoption. 7. USING THE CONTACTLESS CARD READER Figure5 Tapthecontactlesscardontopofthecontactlesslogo(Figure6). Figure6 9. INSERT SIM & SAM CARD ToremovetheSAMcardcompartmentbyunlockingthescrewM1.6*3pieces,pleaseusethe screwdrivertype0(Figure7), Afterremovingthecover,theusercanfindSAM*2slotsatthebottomsideofdevice.Please insertthecardcorrectlyastheiconshownonthecover(Figure8):
Figure7 Figure8 9. INSTALL PRIVACY SHIELD (OPTIONAL ACCESSORY) PleaserefertoFigure9for2stepstoinstalltheshield:
Step1:AlignandinserttwohooksofprivacyshieldwiththeslotonAP10device(filledby rubber). Step2:Pushdownthebottomsideofshieldtocombinewiththedevice.Andtheoutlook isthesameasFigure10. Figure9 Figure10 FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RadiationExposureStatement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. XAC Automation Corporation 886-3-577-2738 The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation.