TERM MINAL PAYM MENT DEVI ICE XCL_ _AT-10 00 SERIE ES INST TALLATIO ON GUIDE E d xCL_AT100s
-
xCL_AT
-
xCL_AT series:
10017U T10017E 1. PACKAG GE CONTENT
Power ada aptor USB cab ble Privacy Shhield Paper Roll
AT-100 0 2. DEVICE AT100K E OVERVIEW eyButtons&Interfac cePorts(Figure1):
FRONT REAR Figure1 FRONTAREA 1 2 Printer Paper Cover 4 Display 3 Magnetic Strip Reader (MSR) slot REARAREA 4 5 6 7 8 Power Button (Press > 3 seconds to power on/off) Smart Card Reader (SCR) slot Charging contact points (Optional) USB port (type C) for charging Battery Compartment AT-100 power spec:
Input:5VDC,2A Power Adapter spec:
Input:100~240Vac Output:5VDC,2A ThissymbolisintendedtoalerttheuserbeforestartingusingthePOS. Caution:UseonlytheACadapterapprovedandprovidedbyXACAutomationCorporationfor usewiththisdevice.UseofanyotherACadaptermaycauseariskoffireorexplosion.
OperatingTemperature:0oCto40oC 3. POWER ON/OFF THE DEVICE Topoweronthedevice:LongpressthePowerkey(Figure2)>3secondsuntilabuzzersound isheard,andscreenisactivated. Topoweroffthedevice:
1)PressthePowerkey>3secondstoshutdownthedevice. 2)Noactionondeviceafter30minutes. Figure2 NOTE:WhenthereisnoactiononAT100after2mins(adjustable),thedevicewillentersleep mode.Pleaseshortpresspowerbuttontowakeupthedevice. 4. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe side facing the same direction as the display.(Figure3) Figure3 5. USING THE IC CARD READER Insert an IC card into the slot (Figure 4) with the chip side facing the same direction as the touchpanel(Figure5). Figure4 Figure5 6. USING THE KEY PAD Afterinsertingthechipcard,Pressthenumerickeyasbelowkeypad(Figure6)toenterthe desirablenumbers.PressCancel(X)keytoterminateanycurrentfunctionandpresstheEnter
(O)keytoconfirmavalueoranoption. Figure6 7. USING THE CONTACTLESS CARD READER Tapthecontactlesscardontopofthecontactlesslogo(Figure7). Figure7 8. REMOVE THE BATTERY STEP1:PushthelatchtopullthebottomcoverfromAT100asFigure8. STEP2:Afterremovingthebottomcover,pullupthebatteryconnectorasbelowFigure9to changeanewbattery. Figure8 Figure9 BottomCoverRemovalWarning Whenremovingthebottomcoverandscrewsforthepurposesofchangingbattery,remembertoput backthecoverandscrewsbeforepoweronthePOS. CAUTION:
RISKOFEXPLOSIONIFBATTERYISREPLACEDBYANINCORRECTTYPE.DISPOSEOFUSEDBATTERIES ACCORDINGTOTHEINSTRUCTIONS. Warningforinternalbatterypack Toreduceriskoffireorburns:
1. 2. 3. Donotattempttoopen,disassemble,orservicethebatterypack. Donotcrush,puncture,shortexternalcontacts,ordisposeofinfireorwater. Donotheatabove60oC 9. INSERT SAM CARD Afterremovingthebattery,theusercanfindSAM*2(left)slotsatthebottomsideofdevice. Pleaseinsertthecardcorrectlyastheiconshownonthecover:
Figure10 10. LOADING THE PAPER Gently pop the printer covers latch; then pull the cover (Figure 11). Load a roll of thermal paper into the printer. Load it so that the printside of the paper will feed out facing the operator.Closethecoverbypressingonthecenteroftheprintercover.Usetheserratedbar totearoffanyexcesspaper. Figure11 FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RadiationExposureStatement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Specific Absorption Rate (SAR) Testing Your device has been designed to comply with applicable limits for RF exposure. These limits use a unit of measurement called Specific Absorption Rate, or SAR, which refers to the rate at which the body absorbs RF energy. The Federal Communications Commission (FCC) has established a SAR limit for mobile phones of 1.6 W/kg, which applies in the United States and other countries that follow the FCCs SAR limit. SAR testing is conducted with the device placed in common operating positions (e.g., held against the head, worn on the body) and transmitting at its highest certified power level in each frequency band of operation. Because the device is transmitting at its highest certified power level, SAR tests capture a worst-case operating scenario and therefore often do not reflect the amount of RF exposure during normal, everyday use. More information on SAR testing is available on the FCCs website at http://www.fcc.gov/guides/
wireless-devices-and-health-concerns. XAC Automation Corporation submitted SAR test results demonstrating compliance with the FCCs SAR limit for wireless devices as part of the FCCs equipment certification process for this device. These results can be accessed via the FCCs equipment authorization database (found at http://transition.fcc.gov/oet/ea/fccid/) by searching for the devices FCC ID: MQT-AT10017U. XAC Automation Corporation 886-3-577-2738 The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation.