FCC ID: MQT-AT150R6 Terminal

TERMINAL PAYMENT DEVICE XCL_AT-150 SERIES INSTALLATION GUIDE xCL_AT-150 series:

xCL_AT-150-R6-18U xCL_AT-150-R6-18E d This symbol is intended to alert the user before starting using the POS. Before using the Device. Please do the full charge (0% ~ 100%) once to get the best battery performance. Please ensure the unit was not stored for over one month without charging. Battery life will depend on different use-cases and the battery manufacturer recommends replacing it with a new one every 2 years. Caution: Do not attempt to open and disassemble the device, that will cause device tamper. 1. PACKAGE CONTENT AT-150 Power adaptor Paper Roll 2. DEVICE OVERVIEW Device Overview (Figure 1):

FRONT LEFT REAR Figure 1 FRONT AREA Printer Paper Cover 1 2 4 5 6 7 8 9 5 Display 3 Magnetic Strip Reader (MSR) slot Smart Card Reader (SCR) slot LEFT AREA Power Button (Press > 3 seconds to power on/off) Audio Jack REAR AREA Charging contact points USB port (type C) for charging Camera for 1D/2D barcode scanning (Optional) 10 Battery Compartment AT-150 Power spec:

Input: 5V DC, 3A Power Adapter spec:

Input: 100 ~240 Vac Output: 5V DC, 3A Operating Temperature: 0oC to 40oC 3. POWER ON/OFF THE DEVICE Caution: Use only the AC adapter approved and provided by XAC Automation Corporation for use with this device. Use of any other AC adapter may cause a risk of fire or explosion. To power on the device: Long press the Power button (Figure 2) > 3 seconds and the device screen will be activated. To power off the device: Press the Power button > 3 seconds to shut down the device. Power Button Figure 2 NOTE: When device is in idle or suspend mode, short press power button will wake up the device. 4. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe side facing the same direction as the display. (Figure 3) Figure 3 5. USING THE IC CARD READER Insert an IC card into the slot (Figure 4) with the chip side facing the same direction as the touch panel (Figure 5). Figure 4 Figure 5 6. USING THE KEY PAD After inserting the chip card, Press the numeric key as below keypad (Figure 6) to enter the desirable numbers on touch panel. Press Cancel (X) key to terminate any current function and press the Enter (O) key to confirm a value or an option. Figure 6 7. USING THE CONTACTLESS CARD READER Tap the contactless card on top of the contactless logo (Figure 7). Figure 7 8. REPLACE THE BATTERY 8-1 REMOVE THE BATTERY STEP 1: Push the battery latch to pull the battery from AT-150 as Figure 8. STEP 2: After removing the battery as below Figure 9 to change a new battery. Figure 8 Figure 9 8-2 INSTALL THE BATTERY STEP 1: Insert the battery connector into AT150 as Figure 10. STEP 2: After install the battery and press the battery latch gently as Figure 11. Figure 10 Figure 11 Bottom Cover Removal Warning When removing the bottom cover and screws for the purposes of changing battery, remember to put back the cover and screws before power on the POS. CAUTION:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Warning for internal battery pack To reduce risk of fire or burns:

1. 2. 3. Do not attempt to open, disassemble, or service the battery pack. Do not crush, puncture, short external contacts, or dispose of in fire or water. Do not heat above 60 oC Installing the battery 1. After install the battery, please make sure the battery is fitted properly into the battery 2. compartment. Please do the full charge (0% ~ 100%) once to get the best battery performance after battery replacement. Note: The battery is considered a consumable item and excluded from XACs Product Warranty. 9. INSERT SAM/SIM CARD After removing the battery, the user can find SAM*2 (left) slots and SIM*2(right) slot at the bottom side of device. Please insert the card correctly as the icon shown on the cover as Figure 12:

Figure 12 10. LOADING THE PAPER Gently pop the printer covers latch; then pull the cover (Figure 13). Load a roll of thermal paper into the printer. Load it so that the print-side of the paper will feed out facing the operator. Close the cover by pressing on the center of the printer cover. Use the serrated bar to tear off any excess paper. Figure 13 FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT (Only for xCL_AT-150-R6-18U) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user limb or set the device to lower output power if such function is available. Specific Absorption Rate (SAR) Testing Your device has been designed to comply with applicable limits for RF exposure. These limits use a unit of measurement called Specific Absorption Rate, or SAR, which refers to the rate at which the limb absorbs RF energy. The Federal Communications Commission (FCC) has established a SAR limit for mobile phones of 1.6 W/kg, which applies in the United States and other countries that follow the FCCs SAR limit. SAR testing is conducted with the device placed in common operating positions (e.g., held against the head, worn on the limb) and transmitting at its highest certified power level in each frequency band of operation. Because the device is transmitting at its highest certified power level, SAR tests capture a worst-case operating scenario and therefore often do not reflect the amount of RF exposure during normal, everyday use. More information on SAR testing is available on the FCCs website at http://www.fcc.gov/guides/

wireless-devices-and-health-concerns. XAC Automation Corporation submitted SAR test results demonstrating compliance with the FCCs SAR limit for wireless devices as part of the FCCs equipment certification process for this device. These results can be accessed via the FCCs equipment authorization database (found at http://transition.fcc.gov/oet/ea/fccid/) by searching for the devices FCC ID: MQT-AT150R6. XAC Automation Corporation 886-3-577-2738 www.xac.com.tw The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation. XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of his material.

The label will be permanently affixed at a conspicuous location on the device. LABEL LOCATION Label Here FCC IDMQT-AT150R6

XAC Automation Corporation 4F, NO. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN Date: 2020/10/21 FCC ID: MQT-AT150R6 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram Operational Description Software Operational Description Part list Tune-up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours,

Eric Hong/Section Manager XAC Automation Corporation Tel: 886-3-5772738 #6663 Fax: 886-3-5678022 E-Mail: eric_hong@xac.com.tw

XAC Automation Corporation 4F, NO. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN A U T H O R I Z A T I O N L E T T E R Date: 2020/10/21 FCC ID: MQT-AT150R6 To Whom It May Concern:

XAC AUTOMATION CORP. hereby authorizes Amanda Wu/Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu/Senior Specialist of BV CPS Taoyuan on XAC AUTOMATION CORP.s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,

Eric Hong/Section Manager XAC Automation Corporation Tel: 886-3-5772738 #6663 Fax: 886-3-5678022 E-Mail: eric_hong@xac.com.tw

XAC Automation Corporation 4F, NO. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN Date: 2020/10/21 FCC ID: MQT-AT150R6 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commissions rules, we request short-term confidential treatment for the following information until 180 days in order to ensure sensitive business information remains confidential until the actual marketing of the device:

External photos Test Setup photos Users manual Internal Photos Sincerely yours,

Eric Hong/Section Manager XAC Automation Corporation Tel: 886-3-5772738 #6663 Fax: 886-3-5678022 E-Mail: eric_hong@xac.com.tw

XAC Automation Corporation 4F, NO. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN Date: 2020/10/21 We, XAC AUTOMATION CORP. declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: MQT-AT150R6 If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

Eric Hong/Section Manager XAC Automation Corporation Tel: 886-3-5772738 #6663 Fax: 886-3-5678022 E-Mail: eric_hong@xac.com.tw

XAC Automation Corporation 4F, NO. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN DFS client device channel plan and software operational declaration Date: 2020/10/5 We, XAC AUTOMATION CORP., declare that the device, FCC ID: MQT-AT150R6 Model Name: xCL_AT-150-R6-18U, does not have Ad Hoc on non-US frequencies and/or on DFS frequencies. Also, the client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. Below is the channel / frequency plan for the device CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2462 Active Active Active Active Active Active Active Active Active Active Active 2417 2422 2427 2432 2437 2442 2452 2457 2447 Scan Type CH 36 38 40 44 46 48 Frequency (MHz) 5180 5240 Active Active Active Active Active Active 5200 5190 5220 5230 CH 52 54 56 60 62 64 Frequency (MHz) 5260 5270 5280 5300 5310 5320 Passive Passive Passive Passive Passive Passive CH 100 Frequency (MHz) 5500 102 5510 104 5520 108 5540 110 5550 112 5560 116 5580 118 5590 120 5600 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive Passive CH 124 Frequency (MHz) 5620 126 5630 128 5640 132 5660 134 5670 136 5680 140 5700 142 5710 144 5720 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive Passive CH 149 Frequency (MHz) 5745 151 5755 153 5765 157 5785 159 5795 161 5805 165 5825 Scan Type Active Active Active Active Active Active Active Also, on DFS channels, the WLAN driver in the device operates under the control of an AP at all times, except when in ad-hoc mode on US non-DFS channels. The device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is protected by a special signature and CRC checksum. Signature and CRC checksum will be calculated and verified before 5G band 1 Scan Type 5G band 2 Scan Type 5G band 3 5G band 4 XAC Automation Corporation 4F, NO. 30, INDUSTRY E. RD. IX, SCIENCE-BASED INDUSTRIAL PARK, HSINCHU, TAIWAN firmware upgrade. Unauthorized modification to firmware will lead to the failure of verification and thus firmware upgrade will not be allowed. Sincerely yours, Sincerely yours,

Eric Hong/Section Manager XAC Automation Corporation Tel: 886-3-5772738 #6663 Fax: 886-3-5678022 E-Mail: eric_hong@xac.com.tw