TERMINAL PAYMENT DEVICE XCL_AT-170 INSTALLATION GUIDE d 1. PACKAGE CONTENT 2. DEVICE OVERVIEW AT-170
(Optional) Power adaptor USB cable Paper Roll AT-170 Key Buttons & Interface Ports (Figure 1) FRONT REAR Right Side RONT AREA REAR AREA 1 2 3 4 5 6 Figure 1 7 Touch Display Printer Paper Cover & Contactless Card Tapping Area Barcode scanner (Optional) Smart Card Reader (SCR) slot Battery Compartment Charging Contact RIGHT SIDE 7 Magnetic Strip Reader (MSR) slot 8 9 Power Button (Press > 3 seconds to power on/off) USB port (type C) for charging and data transfer AT-170 Power spec:
Input: 5V DC, 2A Power Adapter spec:
Input: 100 ~240 Vac Output: 5V DC, 2A This symbol is intended to alert the user before starting using the POS. Caution: Use only the AC adapter approved and provided by XAC Automation Corporation for use with this device. Use of any other AC adapter may cause a risk of fire or explosion. Operating Temperature: 0oC to 40oC 3. POWER ON/OFF THE DEVICE To power on the device: Long press the Power key (Figure 2) > 3 seconds until a buzzer sound is heard, and screen is activated. To power off the device:
1) Press the Power key > 3 seconds to shut down the device. 2) No action on device after 30 minutes Figure 2 NOTE:
1. When there is no action on AT-100 after 2mins (adjustable), the device will enter sleep mode. Please short press power button to wake up the device. Long press for 10 seconds for Force Power Off. 2. 4. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe side facing the opposite direction of the display. (Figure 3) Figure 3 5. USING THE IC CARD READER Insert an IC card into the slot with the chip side facing the same direction as the touch panel
(Figure 4). Figure 4 6. USING THE KEY PAD After inserting the chip card, Press the numeric key on virtual keypad (Figure 5) shown on the display to enter the password. Press Cancel (X) key to terminate any current function and press the Enter (O) key to confirm a value or an option. Figure 5 7. USING THE CONTACTLESS CARD READER Tap the contactless card on top of the contactless logo which is shown on the paper cover.
(Figure 6). Figure 6 8. REMOVE THE BATTERY STEP 1: Loose 2*screws and open the battery cover from bottom of AT-170 as Figure 7. STEP 2: After removing the bottom cover, pull up the battery connector as below Figure 8 to change a new battery. Figure 7 Figure 8 Bottom Cover Removal Warning When removing the bottom cover and screws for the purposes of changing battery, remember to put back the cover and screws before power on the POS. CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Warning for internal battery pack To reduce risk of fire or burns:
1. 2. Do not attempt to open, disassemble, or service the battery pack. Do not crush, puncture, short external contacts, or dispose of in fire or water. 3. Do not heat above 60 oC 9. INSERT SAM CARD After removing the battery cover, the user can find SAM *2 (left) slots at the upper side of battery (Figure 9). Please insert the card correctly as the icon shown on the cover:
Figure 9 10. LOADING THE PAPER Gently pop the printer covers latch; then pull the cover (Figure 10). Load a roll of thermal paper into the printer. Load it so that the print-side of the paper will feed out facing the operator. Close the cover by pressing on the center of the printer cover. Use the serrated bar to tear off any excess paper. Figure 10 FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Specific Absorption Rate (SAR) Testing Your device has been designed to comply with applicable limits for RF exposure. These limits use a unit of measurement called Specific Absorption Rate, or SAR, which refers to the rate at which the body absorbs RF energy. The Federal Communications Commission (FCC) has established a SAR limit for mobile phones of 1.6 W/kg, which applies in the United States and other countries that follow the FCCs SAR limit. SAR testing is conducted with the device placed in common operating positions (e.g., held against the head, worn on the body) and transmitting at its highest certified power level in each frequency band of operation. Because the device is transmitting at its highest certified power level, SAR tests capture a worst-case operating scenario and therefore often do not reflect the amount of RF exposure during normal, everyday use. More information on SAR testing is available on the FCCs website at http://www.fcc.gov/guides/
wireless-devices-and-health-concerns. XAC Automation Corporation submitted SAR test results demonstrating compliance with the FCCs SAR limit for wireless devices as part of the FCCs equipment certification process for this device. These results can be accessed via the FCCs equipment authorization database (found at http://transition.fcc.gov/oet/ea/fccid/) by searching for the devices FCC ID:
This device used the modular approval for 3G technology, and the modular approval FCC ID is QISMU509-65 MQT-AT17017U The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be XAC Automation Corporation 886-3-577-2738 www.xac.com.tw disclosed, distributed or reproduced without permission of XAC Automation Corporation. XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein;