FCC ID: MQT-AT170R18W Terminal

DESKTOP/MOBILE PAYMENT TERMINAL XCL AT-170-R SERIES INSTALLATION GUIDE d xCL_AT-170 series:

xCL_AT-170-R-18W Before using the device, please full charge the battery To keep the device in good condition This symbol is intended to alert the user before starting using the POS. 1. PACKAGE CONTENT AT-170 Power adaptor USB cable Paper Roll Hand Strap

(Optional)

(Optional)

(Optional) 2. DEVICE OVERVIEW AT-170 Key Buttons & Interface Ports (Figure 1) FRONT REAR Right Figure 1 RONT AREA 7 Touch Display Printer Paper Cover & Contactless Card Tapping Area Camera for barcode scanning (Optional) Smart Card Reader (SCR) slot REAR AREA Battery Compartment Charging Contact RIGHT SIDE 7 Magnetic Strip Reader (MSR) slot Power Button (Press > 3 seconds to power on/off) 1 2 3 4 5 6 8 9 USB OTG port (type C) AT-170 Power spec:

Input: 5V DC, 2A Power Adapter spec:

Input: 100 ~240 Vac Output: 5V DC, 2A Operating Temperature:

0oC to 40oC 3. POWER ON/OFF THE DEVICE Caution: Use only the AC adapter approved and provided by XAC Automation Corporation for use with this device. Use of any other AC adapter may cause a risk of fire or explosion. Power ON Press and hold the Power key for 3 seconds until the screen is activated.

(Figure 2) Power OFF -- Press and hold the Power key for 3 seconds to shut down the device. Figure 2 NOTE:

1. When device is in idle or suspend mode, short press power button will wake up the 2. When device require to forced shut down, press and hold the power button for 10 device. seconds 4. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe at the back side of the card.

(Figure 3) 5. USING THE IC CARD READER Insert an IC card into the slot with the chip side facing upward (Figure 4). Figure 3 Figure 4 6. USING THE KEY PAD After inserting the chip card, press the numeric keys of virtual keypad (Figure 5, as reference) shown on the display to enter the password. Press Cancel (X) key to terminate any current function and press the Enter (O) key to confirm a value or an option. Figure 5 7. USING THE CONTACTLESS CARD READER Tap the contactless card on top of the contactless logo which is shown on the paper cover. The 4 green LED indicates the contactless card reading status.(Figure 6). Figure 6 8. CHANGE THE BATTERY STEP 1: Remove the 2 screws and open the battery cover as Figure 7. STEP 2: Lift the battery and pull up the battery connector from device as Figure 8 STEP 3: Insert the connector of new battery into the device as Figure 8 Note: Please ensure the orientation of connector of battery cable matches the connector on the device. STEP 4: Place the new battery into the compartment STEP 5: Place the battery cover to close the compartment as Figure 7. STEP 6: Fasten the 2 screws. Figure 7 Figure 8 Bottom Cover Removal Warning When removing the bottom cover and screws for the purposes of changing battery, remember to put back the cover and screws before power on the POS. CAUTION:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Warning for internal battery pack To reduce risk of fire or burns:

1. 2. 3. Do not attempt to open, disassemble, or service the battery pack. Do not crush, puncture, short external contacts, or dispose of in fire or water. Do not heat above 60 oC 9. INSERT SAM CARD After removing the battery cover, two SAM card slot are top of the battery (Figure 9). Please insert the card correctly as the icon shown on the cover:

Figure 9 10. LOADING THE PAPER paper roll cover (Figure 10). STEP 1: Gently pop the printer covers latch; then pull the cover upward to open the STEP 2: Load a roll of thermal paper into the printer. Please ensure the printing-side of the paper will feed out facing the operator. STEP 3: Close the cover by pressing on the center of the printer cover. Use the serrated bar to tear off any excess paper. Figure 10 11. INSTALL THE STRAP Align two ends of strap pin to the notches on AT-170 rear cover as Figure 11-1. Figure 11-1 Press downward the strap pin into the notches, than pull another pin of the strap to install another side as Figure 11-2. Note: After pressing the pin, make sure it is fixed into the notch of AT-170 as Figure 11-3. Figure 11-2 Figure 11-3 Finished look of the strap assembly is as Figure 11-4. Figure 11-4 Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. RF exposure statements The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when used close to the body is 0.515 W/kg. Industry Canada statement:

following two conditions:

1) This device may not cause interference, and This device complies with Industry Canada license-exempt RSSs. Operation is subject to the 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Caution:

1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

3) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and Avertissement:

1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

2) Le gain maximal dantenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la imitation P.I.R.E.;

3) Le gain maximal dantenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer la limitation P.I.R.E spcifie pour lexploitation point point et non point point, selon le cas. Radiation Exposure Statement:

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition DAS incontrle pour la population gnrale de la norme CNR-102 d'Industrie Canada et a t test en conformit avec les mthodes de mesure et procdures spcifies dans IEEE 1528 et IEC 62209. Cet appareil et sa ou ses antennes ne doivent pas tre co-localiss ou fonctionner en conjonction avec tout autre antenne ou transmetteur. Body SAR: 0.515 W/kg XAC Automation Corporation 886-3-577-2738 www.xac.com.tw The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation. XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of his material.

d DESKTOP/MOBILE PAYMENT TERMINAL Utimaco C3 INSTALLATION GUIDE Before using the device, please full charge the battery To keep the device in good condition This symbol is intended to alert the user before starting using the POS. 1. PACKAGE CONTENT Utimaco C3 Power adaptor USB cable Paper Roll Hand Strap

(Optional)

(Optional)

(Optional) 2. DEVICE OVERVIEW UTIMACO C3 Key Buttons & Interface Ports (Figure 1) FRONT REAR Right Figure 1 RONT AREA 7 Touch Display Printer Paper Cover & Contactless Card Tapping Area Camera for barcode scanning (Optional) Smart Card Reader (SCR) slot REAR AREA Battery Compartment Charging Contact RIGHT SIDE 7 Magnetic Strip Reader (MSR) slot Power Button (Press > 3 seconds to power on/off) 1 2 3 4 5 6 8 9 USB OTG port (type C) UTIMACO C3 Power spec:

Input: 5V DC, 2A Power Adapter spec:

Input: 100 ~240 Vac Output: 5V DC, 2A Operating Temperature:

0oC to 40oC 3. POWER ON/OFF THE DEVICE Caution: Use only the AC adapter approved and provided by XAC Automation Corporation for use with this device. Use of any other AC adapter may cause a risk of fire or explosion. Power ON Pressand hold the Power keyfor 3 seconds untilthe screen activated.(Figure 2) Power OFF -- Pressand hold the Power key for 3 seconds to shut down the device. is Figure 2 NOTE:

1. When device is in idle or suspend mode, short press power button will wake up the 2. When device require to forced shut down, press and hold the power button for 10 device. seconds 4. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe at the back side of the card.(Figure 3) 5. USING THE IC CARD READER Insert an IC card into the slot with the chip side facing upward(Figure 4). Figure 3 Figure 4 6. USING THE KEY PAD After inserting the chip card, press the numeric keysof virtual keypad (Figure 5, as reference) shown on the display to enter the password. Press Cancel(X) key to terminate any current function and press the Enter(O) key to confirm a value or an option. 7. USING THE CONTACTLESS CARD READER Tap the contactless card on top of the contactless logo which is shown on the paper cover.The 4 green LED indicates the contactless card reading status.(Figure6). Figure 5 Figure 6 8.CHANGE THE BATTERY STEP 1: Remove the 2 screws and open the battery cover as Figure 7. STEP 2: Lift the battery and pull up the battery connector from device asFigure 8 STEP 3: Insert the connector of new battery into the device as Figure 8 Note: Please ensure the orientation of connector of battery cable matches the connector on the device. STEP 4: Place the new battery into the compartment STEP 5: Place the battery cover to close the compartment as Figure 7. STEP 6: Fasten the 2 screws. Figure 7Figure 8 Bottom Cover Removal Warning When removing the bottom cover and screws for the purposes of changing battery, remember to put back the cover and screws before power on the POS. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES CAUTION:

ACCORDING TO THE INSTRUCTIONS. Warning for internal battery pack To reduce risk of fire or burns:

1. 2. 3. Do not attempt to open, disassemble, or service the battery pack. Do not crush, puncture, short external contacts, or dispose of in fire or water. Do not heat above 60oC 9. INSERT SAM CARD After removing the battery cover, two SAM card slot are top of the battery (Figure 9). Please insert the card correctly as the icon shown on the cover:

Figure 9 10. LOADING THE PAPER paper roll cover (Figure 10). STEP 1: Gently pop the printer covers latch; then pull the cover upwardto open the STEP 2: Load a roll of thermal paper into the printer. Please ensure the printing-side of the paper will feed out facing the operator. STEP 3: Close the cover by pressing on the center of the printer cover. Use the serrated bar to tear off any excess paper. Figure 10 11. INSTALL THE STRAP Align two ends of strap pin to the notches on UTIMACO C3 rear cover as Figure 11-1. Figure 11-1 Press downward the strap pin into the notches, than pull another pin of the strap to install another side as Figure 11-2. Note: After pressing the pin, make sure it is fixed into the notch of UTIMACO C3 as Figure 11-3. Figure 11-2 Figure 11-3 Finished look of the strap assembly is as Figure 11-4. Figure 11-4 Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. RF exposure statements The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when used close to the body is 0.515 W/kg. Industry Canada statement:

following two conditions:

1) This device may not cause interference, and This device complies with Industry Canada license-exempt RSSs. Operation is subject to the 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsentappareilestconforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillageradiolectriquesubi, meme si le brouillage est susceptible dencompromettre le fonctionnement. Caution:

1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

3) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and Avertissement:

1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmescanaux;

2) Le gain maximal dantennepermis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la imitation P.I.R.E.;

3) Le gain maximal dantennepermis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer la limitation P.I.R.E spcifie pour lexploitation point point et non point point, selon le cas. Radiation Exposure Statement:

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cetappareilestconforme aux limitesd'exposition DAS incontrle pour la population gnrale de la norme CNR-102 d'Industrie Canada et a ttestenconformit avec les mthodes de mesure et procduresspcifies dans IEEE 1528 et IEC 62209. Cetappareil et saousesantennes ne doivent pas tre co-localissoufonctionnerenconjonction avec tout autreantenneoutransmetteur. Body SAR:0.515 W/kg

XAC Automation Corporation

4F., No. 30 Industry E. Road IX,Science-Based Industrial Park Hsin-Chu, 300, Taiwan, ROC

We, XAC Automation Corporation, declare that the device does not support channel 12 ~ 13 in

2.4GHz band and any non-US channels in all the operational mode(s) for the following product.

Date: July 12, 2021

FCC ID: MQT-AT170R18W

IC ID: 6692A-AT170R18W

If you should have any question(s) regarding this declaration, please don’t hesitate to contact us.

Thank you!

Sincerely yours,

Company Name:XAC Automation Corporation

Contact / Title:Eric Hong/ Technical Section Manager

Tel:886-3-577-2738

E-mail: Eric_hong@xac.com.tw

XAC Automation Corporation

UNII Declaration Letter

To whom it may concern:

We have declared below featured for FCC equipment authorization,

device FCC ID: MQT-AT170R18W

(1) DFS Device --

Master,

Client without radar detection capability,

Client with Radar detection capability ,

N/A

Frequency Band

(MHz)

(2) Active / Passive Scanning , adhoc mode access point capability

Active Scanning

(the device can

transmit a probe

(beacon))

Yes,

passive scanning

(where the device

is can listen only

with no probes)

No

5150 – 5250 MHz

Yes,

No

Ad Hoc Mode

capability

Access point

capability

5250 – 5350 MHz

5470 – 5725 MHz Yes,

Yes,

5725 – 5850 MHz

Yes,

No

No

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes,

No

Yes ,

(3) Country code selection ability -

If no, pls explain how was implemented : use Microsoft network utility

(4) Transmit Power Control ability -

(5) Meet 15.202 requirement -

pls check below :

Yes ,

Yes ,

No ,

No

No

A master device is defined as a device operating in a mode in which it has the capability to

transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a

network by sending enabling signals to other devices

A client device is defined as a device operating in a mode in which the transmissions of the device

are under control of the master. A device in client mode is not able to initiate a network.

(6) For client devices that have software configuration control to operate in different modes (active

scanning in some and passive scanning in others) in different bands (devices with multiple equipment

classes or those that operate on non-DFS frequencies) or modular devices which configure the modes

of operations through software, the application must provide software and operations description on

how the software and / or hardware is implemented to ensure that proper operations modes can not

be modified by end user or an installer.

No Apply ,

Apply ,

If apply , pls help to provide explanation on how it was implement (By hardware or software, and how software was controlled)

Factory set only.

(7) Please help to provide justification how device was restricted to operate in 5600~5650MHz in

below.

Enable

Signatory

Contact Name: Eric Hong

Company Name: XAC Automation Corporation

Address: 4F., No. 30 Industry E. Road IX,Science-Based Industrial Park Hsin-Chu, 300, Taiwan, ROC

Tel: 886-3-577-2738

Email: Eric_hong@xac.com.tw

Models Difference Description letter

DATE : 2021/7/27

Dear Sir or Madam,

Due to the business consideration, we hereby declare that our product of Terminal

Model: xCL_AT170-R-18W and Utimaco C3 as following is the difference

Brand

XAC

Model

xCL_AT-170-R-18W

Components

Utimaco

Utimaco C3

Same as xCL_AT-170-R-18W, marketing purpose only.

Any questions regarding this declaration, Please don’t hesitate to contact us.

(Signature)

FCC grantee contact person information.

Name/Title: Eric Hong/ Technical Section Manager

Company Name: XAC Automation Corporation

TEL: 886-3-577-2738

Email: Eric_hong@xac.com.tw

Address: 4F., No. 30 Industry E. Road IX,Science-Based Industrial Park Hsin-Chu, 300, Taiwan, ROC

XAC Automation Corporation

DATE: 2021/7/27

Equipment Autorisation Division

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

FCC ID: MQT-AT170R18W

Request for Confidentiality

• Schematics

• Block diagram

• Operation description

• 5G Software Security

Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that

the following documents be held confidential:

(List here the documents for which you are seeking confidentiality – for example …)

These materials contain trade secrets and proprietary information and are not customarily

released to the public. The public disclosure of this information might be harmful to the

company and provide unjustified benefits to our competitors.

(Signature)

FCC grantee contact person information.

Name/Title: Eric Hong/ Technical Section Manager

Company Name: XAC Automation Corporation

Address: 4F., No. 30 Industry E. Road IX,Science-Based Industrial Park Hsin-Chu, 300, Taiwan, ROC

TEL: 886-3-577-2738

Email: Eric_hong@xac.com.tw

XAC Automation Corporation

DATE : 2021/7/12

Equipment Autorisation Division

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

FCC ID: MQT-AT170R18W

 Test Setup Photos

 External Photos

 Internal Photos

 User Manual

Request for Short-Term Confidentiality

Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice

dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to

marketing the device.:

These documents contain detailed system and equipment description and related information about the

product which （XAC Automation Corporation） considers to be proprietary, confidential, and a custom design

and, otherwise would not release to the general public.

Since this design is a basis from which future technological products will evolve, （ XAC Automation

Corporation ） considers this information to be of benefit to its competitors, and that the disclosure of

information in these documents would give competitors an unfair advantage in the market.

This request is being made retroactively due to an over site on our part. We understand that the information

has been publicly available 180 days after date of grant.

Signature

FCC grantee contact person information.

Name/Title: Eric Hong/ Technical Section Manager

Company Name: XAC Automation Corporation

Address: 4F., No. 30 Industry E. Road IX,Science-Based Industrial Park Hsin-Chu, 300, Taiwan, ROC

TEL: 886-3-577-2738

Email: Eric_hong@xac.com.tw