SCAN OPERATION PROGRAMMABLE MEMORY SCAN (PMS) This feature allows you to scan on the sub-band limits. 1. Store the lower sub-band limits into the memory channel P1L. 2. Store the upper sub-band limits into the memory channel P1U. 3. Set the Main band to memory mode by pressing the [V/M] key on the F-1 cat-
egory, if necessary. 2. grammed range. 4. Recall the memory channel P1L or P1U. 5. Press the [F] key briefly to change the [SMART FUNCTION] keys category to F-
6. Press the [SCAN] key on the F-2 category to initiate the scanner within the pro-
7. Press the [SCAN] key again to stop the scanner. 8. Press the [V/M] key on the F-1 category to change the memory mode, then press the
[V/M] key again to change the VFO mode. 9. Nine pairs of band limit memories, labeled P1L/P1U through P9L/P9U available. You therefore can set lower and upper operation limits on a number of bands, if you like. You may customize the functions of the Memory Scan via Set Mode items D03 MEMORY SCAN TYEP in the MEMORY group, F04 MEMORY SKIP/SELCT, F03 SCAN RESUME, F04 SCAN STOP BEEP in the SCAN group, and G08 RX COVER-
AGE in the SYSTEM group. PRIORITY CHANNEL SCAN (DUAL WATCH) This feature is a two-channel scanning capability which allows you to operate on a VFO or Memory channel, while periodically checking a Priority memory channel 000 for ac-
tivity. 1. Store the frequency which you wish to check periodic into the Priority memory channel PRM. to F-2. 2. Press the [F] key repeatedly until the [SMART FUNCTION] keys category replaces 3. Press the [DW] key on the F-2 category to initiate the Dual Watch feature. 4. Press the [SCAN] key again to stop the Dual Watch feature. You may customize the functions of the Dual Watch feature via Set Mode items F01 DUAL WATCH STOP and F03 SCAN RESUME in the SCAN group. FTM-350R OPERATING MANUAL 17 FCC ID: K6620335X40IC: 511B-20335X40 BLUETOOTH OPERATION When install the optional BU-1 Bluetooth Unit, the FTM-350R to send/receive voice message with the optional BH-1A or BH-2A Bluetooth Headset via wireless links. PAIRING 1. Turn the radio and Bluetooth Headset both off. 2. Turn the radio on while press and holding the key which is located at the left of the
[POWER] switch to enter the Special Function mode. 3. Rotate the left side [DIAL] knob to select the function menu item 9 B-T PAIRING. 4. Press the left side [DIAL] knob. 5. Press and hold the power switch on the Bluetooth Headset for five seconds, until the Bluetooth Headsets indicator blinks red/blue alternately. 6. Press the left side [DIAL] knob to initiate the pairing. 7. If the pairing is successful (requires a 20 to 30 seconds), PAIRING OK ! notation will appear on the display. The FTM-350R will turn off and back on again. When the Bluetooth Headset is correctly recognized by the FTM-350, the Bluetooth Headsets indicator will blink blue. 8. Set up the various function of the Bluetooth via Set Mode items K01 BLUETOOTH. 18 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 BLUETOOTH OPERATION OPERATION 1. When the Bluetooth Headset is correctly recognized by the FTM-350R, icon will appear on the display of the FTM-350R and the LED indicator of the Bluetooth Headset will blink blue. 2. Adjust the receiver audio level using the [VOLUME(+)]/[VOLUME()] switches on the Bluetooth Headset. 3. Press the PTT switch on the Bluetooth Headset to transmit. Release the PTT switch 4. to return to receive. If your Bluetooth Headset is BH-2A, you may adjust the microphone gain (Five steps) of the BH-2A by pressing the [VOLUME(+)]/[VOLUME()] switch while press-
ing and holding the PTT switch, if desired. 5. The communication range between the Bluetooth Headset and FTM-350 is around 1 m (3 ft). If you move out of range, a beep will be heard from the Bluetooth Head-
set to alert you. If you move back into range, the Bluetooth Headset will beep to alert you that you are back within range. 6. When the battery voltage of the Bluetooth Headset is low;
the LED on the Bluetooth Headset will blink Red and Blue. a beep will be heard from the Bluetooth Headset. the icon on the FTM-350R will be blinking fast. a. b. c. Charge the battery of the Bluetooth Headset. In the factory default, the FTM-350Rs internal and external speakers are disabled when the Bluetooth Headset is correctly recognized. Additionally, the microphones which lo-
cated on the front panel and connected to the front panel MIC jack are also disabled when the Bluetooth Headset is correctly recognized. However, the microphone which con-
nected to the transceivers MIC jack is alive. You may customize the Bluetooth operation via Set Mode items K01 BLUETOOTH in the OPTION group. See page 42. FTM-350R OPERATING MANUAL 19 FCC ID: K6620335X40IC: 511B-20335X40 INTERNET CONNECTION FEATURE The FTM-350R can be used to access a node (repeater or base station) which is tied into the Vertex Standard WiRES (Wide-Coverage Internet Repeater Enhancement System) network, operating in the SRG (Sister Radio Group) mode. Details may be found at the WiRES-II Web site: http://www.vxstd.com/en/wiresinfo-en/. SRG (SISTER RADIO GROUP) MODE 1. Sets the Set Mode item J06 WiRES in the SIGNALING group to SRG. See page 41. mode. 2. Selects the access number corresponding to the WiRES repeater via Set Mode item J07 WiRES MEMORY in the SIGNALING group. See page 41. 3. When exit from the Set Mode, activate the Internet Connection feature in the SRG 4. With the Internet Connection feature activated, the FTM-350R will generate a brief
(0.1 sec) DTMF tone according to your selection in step 2. This DTMF tone is sent at the beginning of every transmission to establish or maintain the link to the remote WIRES repeater operating in the SRG mode. 4. To disable the Internet Connection feature, select the OFF selection in the Set Mode item J06 WiRES. 20 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 INTERNET CONNECTION FEATURE FRG (FRIENDLY RADIO GROUP) MODE 1. Store the access code of the Internet link to the DTMF memory register via Set Mode item J02 DTMF MEMORY in the SIGNALING group. See page 40. 2. Sets the Set Mode item J06 WiRES in the SIGNALING group to FRG. See page 41. mode. 3. When exit from the Set Mode, activate the Internet Connection feature in the FRG 4. To access the FRG node, perform the following procedures while pressing the PTT switch:
1) Press the [WiRES] key (located at the left edge of the [SMART FUNCTION] key while transmitting). 2) Rotate the [DIAL] knob to select the DTMF memory register corresponding to the WiRES repeater you wish to establish an internet link. 3) Press the [WiRES] key again to transmit the access code. 5. To disable the Internet Connection feature, select the OFF selection in the Set Mode item J06 WiRES. FTM-350R OPERATING MANUAL 21 FCC ID: K6620335X40IC: 511B-20335X40 DTMF OPERATION MANUAL DTMF TONE GENERATION 1. Press the microphones PTT switch to begin transmission. 2. While transmitting, press the desired numbers key on the microphone. 3. When you have sent all the digits desired, release the PTT switch. DTMF AUTODIALER 1. Store the telephone number to the DTMF memory register via Set Mode item J02 DTMF MEMORY in the SIGNALING group. See page 40. 2. Sets the Set Mode item J03 DTMF MODE in the SIGNALING group to ON. See page 40. mitting). 3. When exit from the Set Mode, activate the DTMF Autodialer. 4. To send the telephone number, perform the following procedures while pressing the PTT switch:
1) Press the [DTMF] key (located at the left side of the [POWER] key while trans-
2) Rotate the [DIAL] knob to select the DTMF memory register corresponding to the telephone number you wish to send. 3) Press the [DTMF] key again to transmit the telephone number. 5. To disable the DTMF Autodialer, select the OFF selection in the Set Mode item J06 DTMF MODE. You may send the telephone number by pressing the microphones numeric key ([1] through
[9]) corresponding to the DTMF memory string you wish to send. 22 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 BARO/ALTI PAGE The FTM-350R can display the current Barometric Pressure and relative changes in the pressure. Furthermore, if you install the optional FGPS-1 or FGPS-2 GPS Unit, the FTM-350R can display the current altitude and relative changes in the altitude. To display the Baro/Alti Page, enablesthe BARO/ALTI page via Set Mode item C01 DISPLAY SELECT in the DISPLAY group, beforehand. See page 33. 1 23 4 1 Press the [FWD] or [BCK] key repeatedly, until the Baro/Alti Page appears. The current Barometric Pressure appears at the upper right of the display, and indicates the relative changes in the pressure (barometric chart) in the left half of the display. Additionally, if you install the optional GPS Unit, your current altitude appears at the upper right of the display, and your current position (Longitude/Latitude) appears at the lower right of the display. 2 Press the [SCALE] key to change the time scale of the barometric chart. Available selections are 2H, 6H, 12H, and 24H. 3 Press the [ALTI] key to change the barometric chart to the altitude chart. You may also change the time scale of the altitude chart by pressing the [SCALE] key. 3 To return to the barometric chart, press the [BARO] key. To return to the Radio page, press the [FWD] or [BCK] key repeatedly, until the Radio Page appears. You may change the unit of the barometric and altitude via Set Mode item G10 UNIT SELECT in the SYSTEM group (see page 37).
: The FGPS-2 GPS Unit requires CT-133 GPS Antenna Cable and CT-136 GPS An-
tenna Adapter. FTM-350R OPERATING MANUAL 23 FCC ID: K6620335X40IC: 511B-20335X40 GPS OPERATION (REQUIRE OPTIONAL GPS ANTENNA UNIT) When install the optional FGPS-1 or FGPS-2 GPS Antenna Unit, the FTM-350R al-
lows the display of your position (Longitude/Latitude). Before beginning the GPS operation, enables the GPS page via Set Mode item C01 DISPLAY SELECT in the DISPLAY group. See page 33. 1 4 342 1 Press the [FWD] or [BCK] key repeatedly, until the GPS Page appears. Your current position (Longitude/Latitude) appears at the upper right of the display, and your current altitude and vehicle speed appears at the lower right of the display. Additionally, your course direction (compass) displays in the left half of the display. 2 Press the [DISP] key to change the compass. Available selections are Compass Rose
(North Up), Compass Rose (Heading Up), and Compass Tape. 3 Press the [POINT] key to store the current position and date into the Point memory, if desired. Available Point memories are four groups, and there is four Channel for each group. 4 Press the [PLIST] key to open the Point memory list. Rotate the left side [DIAL]
knob to scroll the list and press the [BCK] key to close the list. You may delete the desired point from the Point memory list by pressing the [DEL] key, if desired. To return to the Radio page, press the [FWD] or [BCK] key repeatedly, until the Radio Page appears. You may change the unit of the altitude and vehicle speed via Set Mode item G10 UNIT SELECT in the SYSTEM group (see page 37), and also change the time format via Set Mode item I02 DATE&TIME FORMAT in the TIMER/CLOCK group (see page 39).
: The FGPS-2 GPS Antenna Unit requires CT-133 GPS Antenna Cable and CT-136 GPS Antenna Adapter. 24 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 GPS OPERATION (REQUIRE OPTIONAL GPS ANTENNA UNIT) Point memory The FTM-350R has 16 point memories (four channels in four group each) which memory your positon (Longitude/Latitude) and its date. When your vehicle nears to one of that Point memory, the Nav pop-up win-
dow will open for ten seconds even if you display any page. You may customize the time when a window opens via Set mode item H03 NAVI POPUP in the NAVI group. And also, you may change the date to your desired name, such as the place name, by the following procedures:
1. Press the [PLIST] key to open the Point memory list. 2. Rotate the left side [DIAL] knob to select the Point memory you wish to change the date. 3. Press the left side [DIAL] knob to appear the detail data of the Point memory. 4. Press the left side [DIAL] knob again to enable edit of the stored data. 5. Rotate the left side [DIAL] knob to toggle the point alarm function on and off. When this selection is set to OFF, the Nav pop-up window do not open even if your vehicle nears to that Point memory. 6. Press the [] key to move the cursor to the date area, then press the [CLR]
key to clear previous data. 7. Enter the desired name the left side
[DIAL] knob (select character/num-
ber) and the [] / [] key (move the cursor). 8. Press the [ENT] key to overwrite the new setting. 9. Press the [NAVI] key to return to the GPS page, then press the [NAVI] key again to initiate the navigation. Impotant Note When the GPS Antenna Unit is first turned on, it may take several minutes to complete a fix of your position. This is normal, as the GPS unit is downloding almanac information from the GPS satellites. FTM-350R OPERATING MANUAL 25 FCC ID: K6620335X40IC: 511B-20335X40 NAVI OPERATION (REQUIRE OPTIONAL GPS ANTENNA UNIT) The FTM-350R enables to navigate to the position memorized in the Point memory beforehand by simple operation. Before beginning the Navigation, enables the NAVI page via Set Mode item C01 DIS-
PLAY SELECT in the DISPLAY group. See page 33. 1 2 4 1 Press the [FWD] or [BCK] key repeatedly, until the NAVI Page appears. 2 Press the [PLIST] key to open the Point memory list, then rotate the left side [DIAL]
knob to select the destination where you wish to go. 3 Press the [NAVI] key to return to the NAVI Page. The destination appears at the upper right of the display, and distance between your current position and destination appears at the lower right of the display. Additionally, your course direction (compass) displays in the left half of the display. 4 Press the [NAVI] key to initiate the navigation. Drive your vehicle so that the CAR icon turns to a D symbol in the Compass display. When your vehicle nears to the destination, emits the alarm beep and GOAL! notation appears in the Compass display. To return to the Radio page, press the [FWD] or [BCK] key repeatedly, until the Radio Page appears. You may customize the NAVI operation via the NAVI group of the Set Mode (see page 38). 26 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 NAVI OPERATION (REQUIRE OPTIONAL GPS ANTENNA UNIT) To Navigate to the New Point If you wish to navigate the place without your having still gone, examine the lon-
gitude/latitude of that place from the map, then overwrite that data into the one of the Point memory previously stored. 1. Press the [PLIST] key to open the Point memory list. 2. Rotate the left side [DIAL] knob to select the Point memory you wish to overwrite. 3. Press the left side [DIAL] knob to appear the detail data of the Point memory. 4. Press the left side [DIAL] knob again to enable edit of the stored data. 5. Edit the stored data to new point by the left side [DIAL] knob (select character/
number) and the [] / [] key (move the cursor). 6. Press the [ENT] key to overwrite the new setting. 7. Press the [NAVI] key to return to the NAVI Page, then press the [NAVI] key again to initiate the navigation. Press the [POINT] key to store the current position and date into the Point memory, if desired. Available Point memories are four groups, and there is four Channel for each group. FTM-350R OPERATING MANUAL 27 FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) The FTM-350R has 87 items in the Set Mode, and they are grouped. It will be convenient for you, if you initially select the group by rotating the left side [DIAL] knob, and then rotate the left side [DIAL] knob to select the item you want after pressing the left side
[DIAL] knob. When you have finished making your adjustment, press the [ESC] key re-
peatedly, until the FTM-350R returns to normal operation. The groups are as follows. A: AUDIO, see page 29. B: TX/RX, see page 31. C: DISPLAY, see page 33. D: MEMORY, see page 34. E: APRS/PKT, refer to the APRS Manual. F: SCAN, see page 35. G: SYSTEM, see page 36. H: NAVI, see page 38. I: TIMER/CLOCK, see page 39. J: SIGNALING, see page 40. K: OPTION, see page 42. 28 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) AUDIO GROUP A01: AF DIFFERENTIAL Function: Enables/Disables the AVC (Automatic Audio Volume Controller). The AVC allows the most comfortable and/or effective reception in noisy environment. Available Values: OFF, MIN, MID, or MAX Default: OFF OFF: Disables the AVC. MIN: Activates the AVC with the low effect level. MID: Activates the AVC with the medium effect level. MAX: Activates the AVC with the high effect level. A02: AF TONE CONTROL Function: Selects the tome pitch control for the received audio. Available Values: HIGH-2, HIGH-1, NORMAL, LOW-1, or LOW-2 Default: NORMAL HIGH-2:
HIGH-1:
The received audio is enhanced in the high-range frequency with the high effect level. The received audio is enhanced in the high-range frequency with the low ef-
fect level. NORMAL: The received audio does not pass through the tome pitch control. LOW-1:
The received audio is enhanced in the low-range frequency with the low effect level. The received audio is enhanced in the low-range frequency with the high ef-
fect level. LOW-2:
A03: SPEAKER Function: Selects the speaker to be used:
Available Values: FRONT+REAR, FRONT, OFF, or REAR Default: FRONT+REAR FRONT+REAR: Output the receiving audio from FRONT (located in the front panel) and FRONT:
OFF:
REAR:
REAR (located in the transceivers body) speakers. Output the receiving audio from FRONT speaker. Disable the FRONT and REAR speakers. Output the receiving audio from REAR speaker. FTM-350R OPERATING MANUAL 29 FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) AUDIO GROUP A04: STEREO/MONO Function: Selects the audio output. Available Values: MONAURAL or STEREO Default: MONAURAL A05: SUB BAND MUTE Function: Selects the operation method of the MUTE function during dual receive opera-
tion. Available Values: OFF, TX MUTE, RX MUTE, or TRX MUTE Default: OFF OFF:
TX MUTE: Disables the sub bands receiver audio output while transmit on the main Disable the MUTE function. RX MUTE: Disables the sub bands receiver audio output when receive the signal on the band. main band. TRX MUTE: Disables the sub bands receiver audio output while transmit on the main band, and when receive the signal on the main band. 30 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) TX/RX GROUP B01: MIC GAIN Function: Adjust the microphone gaine level. Available Values: MIN, LOW, NORMAL, HIGH, or MAX Default: NORMAL B02: PTT MODE Function: Selects the front panels PTT key function. Available Values: MOMENTARY / TOGGLE Default: MOMENTARY B03: RPT SHIFT DIREC Function: Sets the repeater shift direction. Available Values: SHIFT OFF, SHIFT, or SHIFT+
Default: OFF B04: RPT SHIFT FREQ Function: Sets the magnitude of the repeater shift. Available Values: 0.00 - 99.95 MHz (50 kHz/step) Default: Depends on the operating band. B05: RX EXPANSION Function: Enables/Disables the band expansion. Available Values: GENERAL or WIDE COVERAGE Default: GENERAL When this Set Mode item is set to WIDE COVERAGE, you will receive the 108 - 137 MHz and 480 - 999.9875 MHz bands (Cellular blocked). B06: VOX Function: Enables/Disables the VOX operation. Available Values: OFF, REAR HAND-MIC, FRONT HAND-MIC, or INTERNAL MIC Default: OFF OFF:
REAR HAND-MIC: Enable the VOX operation for the microphone which is connected Disable the VOX operation. FRONT HAND-MIC: Enable the VOX operation for the microphone which is connected to the rear panel MIC jack (located in the transceivers body). INTERNAL MIC:
to the front panel MIC jack (located in the control head). Enable the VOX operation for the microphone which is connected to the front panel microphone. FTM-350R OPERATING MANUAL 31 FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) TX/RX GROUP B07: VOX SENSITIVITY Function: Sets the VOX sensitivity. Available Values: MIN, LOW, NORMAL, HIGH, or MAX Default: NORMAL B08: WIDE / NARROW AUTO Function: Selects the receivng mode. Available Values: AUTO, WIDE FM, FM, NARROW FM, or AM Default: AUTO B09: WX ALERT Function:Enables/Disables the weather alert scan feature. Available Values: ON or OFF Default: OFF 32 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) DISPLAY GROUP C01: DISPLAY SELECT Function: Enables/Disable the operating function pages recalls from the [FWD]/[BCK]
key. Available Values: FREQUENCY: ON or OFF, TIMER/CLOCK: ON or OFF, BARO/ALTI: ON or OFF Default: FREQUENCY: ON, TIMER/CLOCK: ON, BARO/ALTI: OFF C02: LCD BRIGHTNESS Function: Sets the displays illumination level. Available Values: MIN, 2, 3, 4, 5, 6, 7, or MAX Default: MAX C03: LCD COLOR Function: Selects the displays backlight color. Available Values: WHITE-BLUE, SKY-BLUE, MARINE-BLUE, GREEN, YELLOW-GREEN, ORANGE, or UMBER Default: WHITE-BLUE C04: LCD CONTRAST Function: Sets the displays contrast level. Available Values: MIN, 2, 3, 4, 5, 6, 7, or MAX Default: 4 FTM-350R OPERATING MANUAL 33 FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) MEMORY GROUP D01: MEMORY DISPLAY Function: Selects the memory channel indication between the Frequency and the channels Alpha-numeric Tag. Available Values: FREQUENCY or ALPHA Default: FREQUENCY D02: MEMORY EDIT Function: Accesses to the memory edit window. D03: MEMORY SCAN TYPE Function: Selects what action will happen on a flagged memory channel. Available Values: ALL MEMORY or SELECT MEMORY Default: ALL MEMORY ALL MEMORY:
The scanner will skip the flagged (SKIP) channels during scan-
ning. SELECT MEMORY: The scanner will only scan the flagged (SELECT) channels dur-
ing scanning. D04: MEMORY SKIP / SELCT Function: Selects the scan flag to the current memory channel. Available Values: OFF, SKIP, or SELECT Default: OFF OFF:
SKIP:
SELECT: The current memory channel is set to scan SELECT channel. All memory channels will be scanned The current memory channel is set to scan SKIP channel. 34 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) SCAN GROUP F01: DUAL WATCH STOP Function: Selects the Dual Watch resume mode. Available Values: AUTO or HOLD Default: AUTO AUTO:
HOLD:
The Dual Watch feature will stop when the signal is received on the priority channel. When the signal drops, the Dual Watch will resume. The Dual Watch feature will stop when the signal is received on the priority channel. It will not restart automatically. F02: SCAN DIRECTION Function: Select the scan start direction while initiates the scanner using the scan com-
mand by pressing the [SCAN] key. Available Values: UP START or DOWN START Default: UP START F03: SCAN RESUME Function: Selects the scan resume mode. Available Values: BUSY, HOLD, TIME 1 sec, TIME 3 sec, or TIME 5 sec Default: BUSY BUSY:
The scanner will holt on a signal it encounters. When the signal drops, the scanner will resume. The scanner will holt on a signal it encounters. It will not restart automati-
cally. HOLD:
TIME 1 sec: The scanner will holt on a signal it encounters, and scanner will resume after TIME 3 sec: The scanner will holt on a signal it encounters, and scanner will resume after TIME 5 sec: The scanner will holt on a signal it encounters, and scanner will resume after one second. three seconds. five seconds. F04: SCAN STOP BEEP Function: Enables/Disables the scan stop beep. Available Values: ON or OFF Default: OFF FTM-350R OPERATING MANUAL 35 FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) SYSTEM GROUP G01: APO Function: Sets the Automatic Power-Off time. Available Values: OFF, 0.5 hour, 1.0 hour, 1.5 hour, 2.0 hour ~ 12.0 hour (1.0 hour/step) Default: OFF G02: ARS Function: Enables/Disables the Automatic Repeater Shift function. Available Values: ON or OFF Default: OFF G03: AUTO STEP Function: Selects the DIAL frequncy step. Available Values: AUTO, 5.00 kHz, 6.25 kHz, 8.33 kHz, 9.00 kHz, 10.00 kHz, 12.50 kHz, 15.00 kHz, 20.00 kHz, 25.00 kHz, 50.00 kHz, or 100.00 kHz Default: AUTO G04: BEEP Function: Adjusts the beep volume level. Available Values: OFF, LOW, or HIGH Default:
G05: F KEY Function: Selects the function of the front panels [F] key Available Values: V/M, MHz, AF DUAL 1 (LINE-IN), AF DUAL 2 (AM), AF DUAL 3 (FM), PA, SQL OFF, T-CALL, or WiRES Default: AF DUAL 3 (FM) G06: MIC P KEY Function: Selects the function of the microphones [P1]/[P2]/[P3]/[P4] programmable keys. Available Values: BAND SCOPE, SCAN, SQL TYPE, DCS CODE, TONE FREQ, RPT SHIFT, REVERSE, TX POWER, SQL OFF, T-CALL, WiRES, or WX Default: P1: , P2: , P3: , P4:
G07: OPERATION MODE Function: Shifting of CPU clock frequency. Available Values: A or B Default: A This Set Mode item is only used to move a sprious response birdie, shold it fall on a desired frequncy. 36 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) SYSTEM GROUP G08: RX COVERAGE Function: Enables or disables the band limiting for the VFO frequncy selecting and memory channel recalling. Available Values: VFO: IN BAND or ALL, MEMORY: IN BAND or ALL Default: VFO: IN BAND, MEMORY: ALL VFO IN BAND:
When the VFO frequency reaches the high band edge of the cur-
rent band, the VFO frequency will jamp to the low band edge of the current band (or vice versa). When the VFO frequency reaches the high band edge of the cur-
rent band, the VFO frequency will jamp to the low band edge of the next band (or vice versa). VFO ALL:
MEMORY IN BAND: Recalls only the memory channel which store the same band as a MEMORY ALL:
current memory channel. Recalls the all memory channels regardless of a band. G09: TOT Function: Sets the TOT time. When your transmission time reaches the selected time, the transceiver returns to the RX mode automatically. Available Values: OFF, 5 min, 10 min, 15min, 20 min, or 30 min Default: OFF G10: UNIT SELECT Function: Selects the measurement units of the environment sensor. Available Values: METER or YARD-POUND Default: YARD-POUND FTM-350R OPERATING MANUAL 37 FCC ID: K6620335X40IC: 511B-20335X40 MISCELLANEOUS SETTING (SET MODE OPERATION) NAVI GROUP H01: ALARM VOLUME Function: Select the volume level of the alarm when the FTM-350R arrived at the destina-
tion. Available Values: OFF, LOW, or HIGH Default: LOW H02: DESTINATION AREA Function: Select the threshold range of the destination. Available Values: 0.05 mile, 0.1 mile, 0.2 mile, 0.3 mile, 0.5 mile, 1.0 mile, or 2.0 mile Default: 0.1 mile H03: NAVI POPUP Function: Selects the NAVI Pop-up function. Available Values: OFF, 1 sec ~ 30 sec, or CONTINUOUS Default: 10 sec 38 FTM-350R OPERATING MANUAL FCC ID: K6620335X40IC: 511B-20335X40