BH-2 Bluetooth Head Set When the optional BU-1 Bluetooth Adapter Unit is installed in the Transceiver*, you may use the optional BH-
2 Bluetooth Headset as a wireless link to send and receive audio to the Transceiver*.
* Check with your Vertex Standard Dealer or Catalog for applicable models. Controls & Connections Microphone POWER switch VOLUME () switch Press this switch while pressing and holding the PTT switch, to decreases the microphone gain. VOLUME (+) switch Press this switch while pressing and holding the PTT switch, to increases the microphone gain. LED Indicator Blinking Blue: When the BH-2 Bluetooth Headset is correctly recognized by the transceiver. Blinking Red: When the BH-2 Bluetooth Headset is not correctly recognized by the trans-
ceiver. Blinking Red/Blue: Battery Voltage is Low. PTT switch Press this key to transmit. Release this key to return to receive (Depends on transceiver settings). SPEAKER Earhook You can wear the BH-2 on your left or right ear. Wearing the BH-2 1. Open the earhook. 2. Loop the earhook over your ear. 3. Press the BH-2 to your ear. 4. Adjust the flexible boom microphone by bending the boom towards your mouth. For more comfort when wearing the BH-2, affix the sup-
plied sponge on the speaker and press the supplied sponge ball onto the earhook, and adjust as necessary. Battery When the battery voltage becomes low, the BH-2s LED indi-
cator will blink red/blue alternately, and the beeper sounds a low pitch tone. If the battery has never been used, or its charge is depleted, it may be charged by connecting to the Charger Sleeve* or Charger Cradle*, as shown in the illustration. Please refer to the transceivers manual for installation of the Charger Sleeve.
* Check with your Vertex Standard Dealer or Catalog for appli-
cable models. 1. Insert the BH-2 into the Charger Sleeve or Charger Cradle. NoteNoteNoteNoteNote: The BH-2 is automatically set to sleep mode, when it is inserted into the Charger Sleeve or Charger Cradle. When it is disconnect from the Charger Sleeve or Charger Cradle, the BH-2 will be active again. 2. If the BH-2 is inserted correctly, the LED indicator will glow Red. A fully discharged battery will be charged com-
pletely in 3 hours. When charging is finished, the LED indicator will glow blue. BH-2 is not designed to attach to a motorcycle helmet. Specifications are subject to change without notice. The BH-2 comes ready to fit the left ear. You may change the BH-2 to fit the right ear in the following procedure. 1. Remove the Earhook by pushing it out with a pointed object. 2. Insert the Earhook from the other side. Pairing Before you can use your BH-2 for the first time, the BH-2 and the transceiver must be paired. Refer to the Transceivers Operating Manual for Pairing in-
structions.
Please bring the BH-2 and the Transceiver close together when doing Pairing. 1. Make sure that the BH-2 is off. 2. Press and hold the POWER switch for five seconds, until the LED indicator blinks red/blue alternately. When the BH-2 is correctly recognized (Requires a 20 to 30 seconds) by the transceiver, the LED indicator will blink blue. Turning ON and OFF TTTTTo turn the o turn the o turn the o turn the BH-2 ON ON ON ON ON o turn the Press and hold the POWER switch for three seconds, un-
til the BH-2s LED indicator glows red, and the beeper sounds a high pitch tone. When the BH-2 is correctly recognized by the transceiver, the LED indicator will blink blue.
When the BH-2 is not correctly recognized by the trans-
ceiver, the LED indicator will blink red. TTTTTo turn the o turn the o turn the OFF OFF o turn the BH-2 OFF OFF o turn the OFF Press and hold the POWER switch for five seconds, until the BH-2s red LED indicator blinks rapidly, the beeper sounds two brief tones, and the BH-2 turns off. LED indicator POWER Switch E A F 4 4 U 7 6 0 POWER Switch Effective Communications Range The communications range between the BH-2 and the Transceiver is around 10m (33 ft). Obstacles between the BH-2 and the Transceiver may decreas the communications distance. When you move out of range, the beeper sounds a low pitch tone. When you move back into range, the beeper sounds a high pitch tone. Operation TTTTTransmission ransmission ransmission ransmission ransmission Press the PTT switch to transmit, and release the switch to return to receive (Depends on transceiver settings). Adjusting the V Adjusting the V olume level olume level Adjusting the Volume level olume level Adjusting the V Adjusting the V olume level Adjust the receiver audio level, using the VOLUME () or
(+) switch.When the audio level reaches the maximum or minimun, the beeper sounds two brief tones. VOLUME (+): Adjusts the receiver audio level upward. VOLUME (): Adjusts the receiver audio level downward. Microphone Gain Setting Microphone Gain Setting Microphone Gain Setting Microphone Gain Setting Microphone Gain Setting Press and hold the PTT switch, while using the VOLUME
(+) or () switch to select a comfortable Microphone gain level (Five steps). When the microphone gain reaches the maximum or minimun, the beeper sounds a high pitch tone. VOLUME (+): Sets the MIC gain upward. VOLUME (): Sets the MIC gain downward. VOLUME () Switch PTT Switch VOLUME (+) Switch Example:Use the CAB-1 Example:Use the CD-40 Battery saver Battery saver Battery saver Battery saver Battery saver If there has been no signal or key button activity for 20 sec-
onds, the Battery Save automatically puts the BH-2 in sleep mode, to conserve battery life. When a signal is received or the PTT key is pressed the BH-2 will be active again. Refer to the Transceivers Manual for Battery saver instructions. Specifications Bluetooth specification Bluetooth profiles Radio Frequency Modulation method Transmitter output power Receiver sensitivity Distance (open area) Audio format Audio frequency range Power supply Battery life Button/Switch LED indicators Ver1.2 HSP 2402 MHz - 2480 MHz GFSK 0 dBm Class 2
<-80 dBm 32 ft (10 meters) SBC 100 Hz - 20 kHz Rechargeable Lithium-Polymer 6 hours Power On/Off, Volume Up/Down, PTT Power on:
Unlink:
Link:
Pairing:
Battery low: Flash red and blue Power off:
Flash red 3 times 32 F to 104 F (0 C to 40 C) 5 - 90 %
FCC, CE, BQB Flash blue twice Flash red Flash blue Red and Blue blinking Operating temperature Operating humidity Certification Replacement Parts Ear hook ................. S8002323 Ear hook sponge ..... S8002325 Speaker sponge ....... S8002324 Wind Screen ........... S8002322