Wireless Remote Station Microphone RAM4W SSM-71H The RAM4W (SSM-71H) allows you to remotely control all functions of the enabled Standard Horizon fixed mount VHF radio. The full dot matrix display and programmable keys make operation simple and fast. Additional features include turning the radio on/off and all DSC functions including Distress. The four RAM4W (SSM-71H) can be connected to fixed mount VHF radio with the optional SCU-30 RAM4W Wireless Access Point. The RAM4W (SSM-71H) is backed by an industry leading 3-years waterproof warranty. Owners Manual The details of the installation and operation of the RAM4W (SSM-71H) is included in the owners manual of the compatible fixed mount radio, or it can be downloaded at www.standardhorizon.com. Application for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 Front and Rear Panel Power/VOL knob Press and hold this knob to turn the transceiver and the remote mic on or off. Turns the adjusts the speaker volume. DIAL/ENT knob While the normal screen is displayed, rotate the DIAL/ENT knob to select your desired channel. While the MENU screen is displayed, rotate the knob to select your desired menu item. Secondary use:
Press this knob to enter a selection in the MENU. SQL key (Squelch control) Press this key to activate the squelch adjusting mode. Press the CH or CH key to adjust the squelch level. PTT (Push-To-Talk) switch Push this switch to enable the transmitter. CLEAR/
Press this key to cancel a menu selection. Press and hold this key to activate the key key lock function. Press and hold this key again to deactivate the key lock function. Microphone When spoken into transmits your voice with reduction of background noise, using Clear Voice Noise Reduction Technology. 2 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 Note: Position your mouth about 1/2 (1.5 cm) away from the microphone hole and speak in a normal voice.
/ key Press these keys to switch the function menu. Secondary use:
While the MENU screen is displayed, press the key to slide the on-screen menu to the right/left side. MENU key Press this key to access the MENU. CH/CH key These keys are used to change the operating channel. Press the key momentarily, the channel increases/decreases one step. Holding the key, the channel increases/decreases continuously. Secondary use:
While the MENU screen is displayed, press the key to slide the on-screen menu upward/downward. When in the PA or Fog mode, press the key to change the channel. Display 222 by 162 pixels full dot matrix display. Soft keys These three programmable keys can be customized through the setup menu mode. When pressing one of these keys briefly, the key functions will appear at the bottom of the display. Strobe Light When the [STROBE] soft key is pressed, the internationally-recognized Morse Code S.O.S message will light and flash repeatedly. From MENU SETUP CONFIGURATION STROBE LED, you can select one option from CONTINUOUS, SOS, BLINK 1, BLINK 2 and BLINK 3. 16/S key Pressing this key immediately recalls channel 16 from any channel location. Holding down this key recalls the SUB channel (The default setting is channel 9). Pressing this key again reverts to the previous selected working channel. Speaker The internal speaker is located here. DISTRESS key This key is used to send a DSC distress call. USB jack Use the micro USB type B jack for SSM-71H (RAM4W) battery charge. Note: When the DATA jack is securely covered with rubber cap, the SSM-71H meets the waterproofing performance. 3 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 Included Accessories and replacement part numbers SAD-17 USB Wall Charger (100-240 VAC) Charger Cable (Type USB A plug to Type USB micro B plug) CLIP-22 Belt Clip Belt Clip Hanger & Screws (U40412220 x 2 pcs) Hand Strap Optional Accessories
(1) SCU-30 Wireless Access Point with 3 Feet Cable
(2) SDD-14 USB DC Charger with Cigarette Lighter Plug Belt Clip Installation / Removal 1. To install, align the Belt Clip Clip-22 to the groove of the rear panel, then press the Belt Clip downward until it locks in place with a Click. 2. To remove, pull the Clip-22 tab away from the real panel to unlock the Clip-22, then slide the Clip-22 upward to remove it. Battery Charging If the battery has never been used, or its charge is depleted, charge the RAM4W according to the following procedures:
1. Turn the RAM4W off. 2. Slide the USB cover button (with arrow) up to open the cover, then connect the supplied Charge Cable to the USB jack. 3. Connect the other side plug of the supplied Charge Cable to the SAD-17 then plug the SAD-17 into the AC line outlet. 4. If the connection is correct, the RAM4Ws LCD display will show the battery charging icon. 5. A fully-discharged RAM4W will be charged completely in approximately 4 hours. When charging is completed, the battery charging icon will disappear. 4 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 CAUTION Waterproof and floating features of the RAM4W are assured only when the USB jack cover is locked completely. The SAD-17 is NOT designed to be waterproof. Charge the radio in a dry location. The RAM4W is equipped with a high-performance Lithium Battery. Built-in Lithium-ion Battery Capacity Nominal Voltage Temperature Range Charge Discharge Storage 1800 mAh 7.4 V Minimum F 41 4 14 C 5 20 10 Maximum F C 35 95 140 60 35 95 Battery Safety Battery packs for your equipment contain Li-ion batteries. This type of battery stores a charge powerful enough to be dangerous if misused or abused, especially when removed from the equipment. Please observe the following precautions:
DO NOT SHORT BATTERY PACK TERMINALS: Shorting the terminals that power the equipment can cause sparks, severe overheating, burns, and battery cell damage. If the short is of sufficient duration, it is possible to melt battery components. Do not place a loose battery pack on or near metal surfaces or objects such as paper clips, keys, tools, etc. When the battery pack is installed on the transceiver, the terminals that transfer current to the transceiver are not exposed. The terminals that are exposed on the battery pack when it is mounted on the transceiver are charging terminals only and do not constitute a hazard. DO NOT INCINERATE: Do not dispose of any battery in a fire or incinerator. The heat of fire may cause battery cells to explode and/or release dangerous gases. Battery Maintenance For safe and proper battery use, please observe the following:
Battery packs should be charged only in non-hazardous environments. Use only STANDARD HORIZON-approved batteries. Use only a STANDARD HORIZON-approved charger. The use of any other charger may cause permanent damage to the battery. Follow charging instructions provided with the chargers. Battery Storage Store the batteries in a cool place to maximize storage life. Since batteries are subject to self-discharge, avoid high storage temperatures that cause large self-discharge rates. After extended storage, a full recharge is recommended. 5 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 Battery Recycling DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH!
LI-ION BATTERIES MUST BE COLLECTED, RECYCLED OR DISPOSED OF IN AN ENVIRONMENTALLY SOUND MANNER. The incineration, land filling or mixing of Li-ion batteries with the municipal solid waste stream is PROHIBITED BY LAW in most areas. Return batteries to an approved Li-ion battery recycler. This may be where you purchased the battery. Contact your local waste management officials for other information regarding the environmentally sound collection, recycling and disposal of Li-ion batteries. Pairing When using the RAM4W for the first time, the RAM4W and the Wireless Access Point SCU-30 must be paired. Refer to the Transceivers Operating Manual for Pairing instructions. 1. Please bring the RAM4W and the SCU-30 close together when doing Pairing. 2. Press and hold [16/S] key and turn on the RAM4W. 3. Press and hold [16/S] key and turn on the transceiver. Searching ... appears on the LCD. 4. When pairing is completed, the display will appears Complited. 6 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 FCC Notice Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or modification must be approved in writing by STANDARD HORIZON. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Changes or modifications to this device not expressly approved by YAESU U.S.A. could void the Users authorization to operate this device. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 7 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 Specifications Supply Voltage:
Current Consumption:
3.7 VDC 450 mA @VOL Max. 100 mA @AF Mute Operating Temperature:
4 F to +140 F (20 C to +60 C) Wireless Networking Module:
FCC ID: K660A290910, IC: 511B-0A290910 Frequency Band:
2.4 GHz Wireless Networking Standard:
IEEE 802.11 b/g/n AF output:
700 mW @ 8 ohms for 10 % THD Display Size:
1.8 x 0.9 (45 x 23 mm) Display Resolution:
222 x 162 dots Dimensions (WxHxD):
2.5 x 5.3 x 1.3 (63 x 135 x 32.5 mm) Weight (Approx):
7.23 oz (205 g) Symbol placed on the equipment Direct Current 8 SSM-71H Instruction ManualApplication for FCC / ICFCC ID: K660A290X10 / IC: 511B-0A290X10 Disposal of Electrical and Electronic Equipment Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Electronic and Electrical Equipment should be recycled at a facility capable of handling these items and their waste byproducts. Please contact a local equipment supplier representative or service center for information about the waste collection system in your country. 9 SSM-71H Instruction ManualApplication for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10 Copyright 2017 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A. YAESU UK Unit 12, Sun Valley Business Park, Winnall Close Printed in Japan Application for FCC / IC FCC ID: K660A290X10 / IC: 511B-0A290X10