FCC ID: M4Y-SP220C03 5GHz 11ac Wireless Bridge

Z-COM, Inc. SP220-C03 5GHz 11ac Wireless Bridge Quick Setup Guide This Quick Setup Guide provides step-by-

step instructions on how to set up your Access Point. After completing the steps described in this Guide, you will be able to place the AP at your site and provide wireless network access to users. PACKAGE CONTENTS Wireless Access Point (1) Mounting screws and bracket (1) HARDWARE OVERVIEW Front View LED Indicators on the Device No LED State Description Off No power to AP 1 PWR 2 WLAN 3 LAN Bottom View Green On Off Blinking Green Off Green On Blinking Green AP power on, device ready 5G radio disabled 5G radio enabled or data being forwarded Ethernet port not connected Ethernet port connected Ethernet link activity Rear View No. Item 1 Ground 2 LED 3 PoE/LAN Port 4 Reset Button 5 LAN Port (Option) SETUP REQUIREMENTS Before installing your Access Point, be sure that you have the following:

A computer running Windows 7, Vista, or XP A CAT5 UTP cable of required length Power adapter/PoE injector came with the package. (4-Pair 802.3at PoE injector 60W) STEP 1: POWER ON THE AP The Access Point comes with a PoE injector kit for connecting to power over the Ethernet port. The Access Point automatically turns on as soon as it is connected to a power source. Cautions:

1. Use only the power adapter and PoE injector that came with the wireless AP. 2. Make sure that the PoE injector is properly grounded 1. 2. Insert one end of an Ethernet cable to the P+D/OUT port on the PoE injector. Insert the other end to the LAN/PoE port on the Access Point. 3. Connect a power cord to the PoE injector. 4. Connect the power plug to a wall socket. STEP 2: CONNECT THE AP TO YOUR PC 1. Insert one end of an Ethernet cable to the DATA/IN port on the PoE injector as figured above. Insert the other end to the assigned LAN port on your PC as figured above. 2. 3. From your computer, go to Start > Settings >

Network Connections or Start > Control Panel >

Network Connections. 4. When the Network Connections window appears, right-click the icon for Local Area Connection, and then click select Properties. 5. Select Internet Protocol (TCP/IP) from the scrolling list, and then click Properties. 6. Select Use the following IP address option (if it is not already selected), and then make the following entries:

IP address: Any address in the 192.168.1.x network Subnet mask: 255.255.255.0 7. Click OK to save your changes, and exit the dialog box. STEP 3: LOG INTO THE AP 1. On your PC, open a Web browser window. 2. In the browser, type https://192.168.1.1 and press <Enter> to connect to the AP. 3. When a security alert dialog box appears, click OK/Yes to proceed. 4. When the login page appears, enter the following:

Username: admin Password: password 5. Click Login. STEP 4: CONFIGURE THE AP The procedure for completing the Access Points essential configuration depends on whether you want it to be managed by either AP controller or to operate as a standalone Access Point. Refer to the section that is relevant to your deployment:

Configuring for Management by AP Controller Configuring for Standalone Operation Configuring for Management by AP Controller To configure the Access Point to be managed by the AP controller, you must ensure that the APs will be able to locate and connect to the controller when powered on. Specifically, you need to ensure the following. When connected to the network, each AP is assigned a valid IP address APs are able to locate and connect the controller The Access Point requires a unique IP address

(fixed IP or DHCP IP) on a network that has connectivity to a controller. The DHCP server can be an existing network server or a ZDC controller configured as a DHCP server. 1. Once login, first assign a fixed IP address or a DHCP IP to the AP under Current IP Setting. Under Wireless Switch Setting, select Connect With Wireless Switch Via IP and input the IP address of the AP access controller. Click Apply to take effect. 2. On the main menu on the left, go to Connection Info to check the connection status with the AP controller. If the tunnel has been made successfully, the connection status will show:

Connected. 4. Configure the common RF setting as such Country/Region domain and Channel. 5. Click Apply to save the changes. Configuring for Standalone Operation Before configuring fat AP Basic settings, make sure that AP mode is set to Fat AP. 1. If currently in Thin AP Mode: On the main menu on the left, click Advanced Setting. Select Fat AP from the drop-down list. Click Apply to take effect. 3. Go to RF Configure > Wireless Settings. 6. Go to RF Configure > Security Profile. 7. Click one of the profiles #, tick the Enable box and press Edit. 2. On the main menu on the left, click Basic Setup. In the Basic Setup page, go to the section Configure AP as. If you want to assign a fixed IP address, select Static IP. Enter the parameters in the following fields: IP Address, Subnet Mask, Default Gateway, Primary DNS Server, and Secondary DNS Server. If you want the wireless AP to obtain the address from the DHCP Server automatically, select DHCP Client. Click Apply. These are the essential wireless settings that will enable wireless devices on the network to associate with the Access Point. 8. Clear the Security Profile Name and Wireless Network Name (SSID) box, and then type a unique name that you desire to call this wireless network. This will help users identify this wireless network in their wireless network connection. 9. Adjust the maximum connected users if necessary. 10. In Network Authentication, select the desire authentication method and then enter the encryption phrase accordingly. 11. Click Apply to save the changes. 12. Click Logout to exit the Web interface. STEP 4: VERIFY THE CONNECTION 1. Connect the AP to your network. 2. Use any wireless-enabled computer or mobile device to search for and select the wireless network youve previously configured. If you can connect, open a browser and link to any public website. 3. STEP 5: INSTALL THE AP 1. Disconnect the APs power adapter from the power outlet (or disconnect the PoE cable). 2. Move the AP to its permanent location

(accessible to both power source and network connections). Note:

Some placement guidelines you should follow to maximize performance and coverage. The Access Point s ideal orientation is pole mount (e.g street light pole) with its dome pointing straight down. All APs should be mounted as high and as visible as possible. 10 meter installation height least is suggested. Try to avoid any obstructions, especially those in close proximity to the AP . The signal strength it will receive depends largely on its position, so make sure that sufficient survey has been made to determine the best placement for maximum range, coverage, and network performance before installing. Nevertheless, as RF can be affected by many variables, your actual performance may vary from the planned design. MOUNTING THE ACCESS POINT 1. Secure the Access Point to the mounting base with the provided screws. 2. Press the mounting bracket to the T-bar at a pre-determined location. 3. On the opposite side of the T-bar, position 4. the T-bar clip. Insert the washers over the retaining screws and insert through the T-bar clip and into the mounting bracket. 5. Secure the Access Point and mounting base to the mounting bracket with the spring washers and screws. 6. Align the Access Point and mounting 7. base assembly with the mounting bracket. Insert the adjusting screws through the mounting base and secure. Note:

Do not tighten the screws completely at this time to allow for final tilt down adjustments. STEP 6: WATERPROFFING THE CABLE You need to waterproof the LAN port using the supplied sealing cap. 1. Slide the locking nut over the bare end of the Ethernet cable. 2. Slightly pry open the gasket and rubber stopper, and insert the Ethernet cable. 3. Slide the gasket and rubber stopper into the locking nut. 4. Connect the RJ-45 connector into the LAN port of the Access Point. 5. Flush the gasket, rubber stopper and locking nut together into the LAN port opening, then twist the locking nut to seal the opening. 2. 3. Insert the other end of an Ethernet cable to the P+D/OUT port on the PoE injector. Make sure the Cat5e cable from the Access Point is long enough to reach the PoE injector. Insert one end of an Ethernet cable to the DATA/IN port on the PoE injector as figured above. 6. Slide the sealing cap over the bare end of 4. Connect the other end of the Ethernet the Ethernet cable. 7. Tighten the sealing cap. 3. From PCs Network - Wireless Properties page. Observe the wireless signal quality and speed. External 5GHz directional-antennas

(Optional accessory_ANT-D5G-15) Note: Linear, 45, Horizontal Beam width 3dB: 60, 6dB:

90, IP55 Waterproof Note: In order to prevent the radio inflection, its recommended to power the device after rotate antenna. Note: Before screw the directional-antenna, please reserve 15 cm between the device and antenna. Note: The pole lock frame can accommodate 3.81~7.62 cm (1.5~3) in diameter. 1. Attach the antenna above the device and unscrew two bolts and take pole lock frame off on the directional-antenna. cable to the switch or a PC. 5. Connect a power cord to the PoE injector. 6. Connect the power plug to a wall socket. 6. Perform a spot-check to verify if the PWR and LAN LED are lit to make sure the AP is operating normally Caution:

1. Make sure that you form a 3-5 drip loop in any cable that is attached to the Access Point. This will prevent water from running along the cable and entering the Access Point or the building where the cable terminates. 2. Be sure that grounding is available and that it meets local and national electrical codes. For additional lightning protection, use lightning rods and lightning arrestors. STEP 8: VERIFY THE CONNECTION 1. Use any wireless-enabled computer or mobile device to search for and select the wireless network youve previously configured. If you can connect, open a browser and link to any public Web site. 2. STEP 7: POWER AND CONNECT 1. Insert the other end to the LAN/PoE port on the Access Point. 2. Attach the pole lock frame and screw two bolts back. Tighten them approximately. 3. Attach two 1.5M N-type cables to the reserved antenna jacks, and connect to the directional antenna. External 5GHz directional-antennas

(Optional accessory_ANT-D5G-23) 1. Align the antenna mount with antenna;

screw tightly all four screws. Note: Dual linear, 45, HPBW/Horizontal 10, HBPW/Vertical 10, IP57 Waterproof Note: Before screw the directional-antenna, please reserve 15 cm between the device and antenna. Note: To prevent radio inflection, it is recommended to power the device on after rotate the directional-antenna. 3. Attach two 1.5M N-type cables to the reserved antenna jacks, and connect to the directional antenna. 2. Unscrew the screws on the two U-bolts, then attach the pole and align two U-bolts with plates. Screw the screws tightly. Grounding & Lightning 1. Make your device GND port connect to ground wire. 2. The ground wire connects to the earth. In addition, the grounding wire meets to 6-AWG copper grounding wire. Note: Be sure that grounding is available and that it must comply with local and national electrical codes. For additional lightning protection, use lightning rods and lightning arrestors. Networking Interface

(2) 10/100/1000 Ethernet Ports

(1) Reset to Defaults Note: This device meets Max. TX power limit per Safety Notice 1. Do not install the device close to any electrical grounding device or lightning protection system. Place the devices own grounding and lightning protection system apart from any electrical grounding device and lightning protection system as far as possible. 2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the power adapter by its edge and do not touch any component or printed circuit boards, especially for module device. 3. Make sure to keep the temperature and humidity of the installation location at an optimal level. 4. An excellent grounding system guarantees the stable operation of device, as well as to protect device from lightning, interference and electrostatic discharges. 5. If installed open site area, the device may be damaged by lightning. We recommend that you install additional lightning protection devices if necessary, considering the conditions in your area. 6. Supply stable power to the device. Unstable power may cause the device to malfunction. The device supports PoE power supply and is recommended if the device is installed near grid lines within less than 100 meters radius. Specifications Specifications Dimensions Weight Buttons Antennas Wi-Fi Standards Power Method Power Supply Max. Power Consumption BSSID Wireless Security Certifications Mounting 310 x 305 x 94 mm 1.4 kg

(2) 5GHz 15dBi Antennas 802.11 a/n/ac 802.3 af /at (PoE/PoE+) 48V, 0.5A PoE 20W Up to 8 per Radio WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES) CE, FCC, NCC Wall/Ceiling(Kits Included) Operating Temperature

-40 70 Operating Humidity 10 to 90 % Non-condensing Compliance Information RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. ETSI regulations. RoHS/WEEE Compliance Statement European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/ or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Declaration of Conformity Hereby, Z-COM, Inc. declares that the radio equipment type SP220-C03 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

https://www.zcom.com.tw/servicepage Federal Communications Commission against protection FCC Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase equipment and receiver. separation between to correct the the try to

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. 15.21 You are changes or modifications not expressly approved by the part responsible for compliance could void the users authority the equipment. FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. to operate cautioned that 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled This equipment should be installed and operated with a minimum distance of 114 centimeters between the radiator and your body. environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation of the device. NCC:

NCC

(Point to Point) 114cm MPE1mW/cm2 0.998 mW/cm2 Copyright 2016 Z-Com, Inc. All rights reserved.

Label & Location Back Side FCC ID: 2AN5A-SSL915-V3-1 Note: 15.19 statements will be placed on the device packaging

Z-Com, Inc, 5F, No.8, Hsin-Ann Rd. Hsinchu Science Park, Hsinchu 30078, Taiwan TEL: +886 35777364 FAX: +886 3 5773359 Date: 12/11/2019 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: M4Y-SP220C03 To whom it may concern:

We, the undersigned, hereby authorize SGS Taiwan Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC |D above, including signing of all documents relating to these matters, Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5304 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Where our agent signs the application for certfication on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., stil resides with <<Z Com Inc>>, This authorization is valid until further written notice from the applicant. Name (Printed): Jeff Jiang Title: Deputy Manager sonatue( Jef Ljanae

(uy !

On behalf of Company: Z-Com, Inc. Telephone: +886 3 5777364

Z-Com, Inc, 5F, No.8, Hsin-Ann Rd. Hsinchu Science Park, Hsinchu 30078, Taiwan TEL: +886 35777364 FAX: +886 3 5773359 To; GS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Z-Com, Inc. DF, No.8 HSIN-ANN RD. HSINCHU SCIENCE PARK, HSINCHU, TAIWAN 30078 Regarding: Confidentiality Request regarding application for FCC ID M4Y-SP220C03 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission's rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certfication application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. Ifthe device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, OW vine wera i Deputy Manager Z-Com, Inc.

Z-Com, Inc. SF, N0.8, HSIN-ANN RD., HSINCHU SCIENCE PARK, HSINCHU 30078, TAIWAN TEL: +886 3 5777364 FAX: +886 3 5773359 Professional Installation Attestation Date: 2020-01-17 FCC ID: M4Y-5P220C03 We, Z-COM, Inc. Hereby declare that requirements of KDB 353028 DO1 Antennas Part 15 Transmitters vO1 have been met and shown on the following questions, Further we declare that the info listed below are correct and represent the product in consideration under this filing 1, Professional installation must be justified. Description: Device is an Outdoor Access Point and must need a specially trained professional in configuring and installing the product, more details please refer to the user manual and installation guide exhibit. 2, Professional installation does not permit the use of any antenna with the transmitter the permitted types of antenna specified as below. Description: Below listed of Antennas has been compliant FCC Rule Part 15 requirement, more details please refer to test reports. Antenna Peak Gain(dBi) AntennaType | Connector Frequency (GHz) 5.150 5.470 5,850 rity [ap || |

treo [Ne [ve [|e |

3, The applicant should address the following items when justifying professional installation,

(1) To muality far nrafaccianal inctallatinn nloaca aynlain why the hardware ic not readily availahle ta the Avy Pee ME Smee fy Se eae PPR Resaaieme Menwece ese teenak Reantacan mrenmeenwiae vdiminangpy [wie secswevne Cenc, SeeeMeansneiiece Tunis JP Wie Sens (e aitenow Moelle we Meier eee ase nine Gee a Daw mecwwens fy Ree a Ntirintieesveaswiner | Aesne meri er average Consumer, Description: Due to this product and will not be sold directly to the general public through the retail store, therefore the hardware is not readily available to the average consumer,

(2} Marketing - The applicant must ensure the device cannot be sold via retail to the general public or by mail order. Description: this product and will not be sold directly to the general public through the retail store. It will kL. JJ. 2. kw Od ed 8 CC eI. gh... UE OUIU LU dUUTIUTIZEU UCdICTS UF HTotalltr Uy,

(3} The applicant must show that device intended use is not for consumers and the general public Description: The device is for industrial/commercial use.

(4) Explain what is unique, sophisticated, complex, or specialized about the equipment that REQUIRES it to be installed by a professional installer?

Description: The device requires to be installed at an appropriate position and the position will affect the performance of the device, Besides, the device receives power from Power over Ethernet (PoE), the method of supplying power is supported by a specific device, Hence, the device requires to be installed by a professional installer. Z-Com, Inc. SF,N0.8, HSIN-ANN RD., HSINCHU SCIENCE PARK, HSINCHU 30078, TAIWAN TEL: +886 3 5777364 FAX: +886 3 5773359 4, Other professional installation requirements,

(1) Installation must be controlled. Description: The product will be distributed through controlled distribution channel which has special trained professional to install this product.

(2) Installed by licensed professionals, VESCripton: VeVICE SOI tO dealer WNO Mires Installers and Need special trained proressional in contiguring and installing the product.

(3} Installation requires special training, Description: The product need special programming, access to keypad, field strength measurements made, 50 must need special trained professional in configuring and installing the product. If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

Hee Assurance Deputy Manager Tel: +886 35777364 Fax: +886 3 5773359 E-mail: support@zcom.com. tw

com, ns JP, INU.) TOTP ATT AU.) PROTTGHTU QUICTILE Fath, MOHIVIY JUU/0, LalWall TEL: +886 35777364 FAX: +886 3 5773359 Date: December 11, 2019 DTS-UNII Device Declaration Letter To Whom It May Concern, we declare below featured for equipment authorization regarding FCC ID: M4Y-$P220003

(t) DFS Device- [| Master (DFS Master), Client with Radar detection capability, | Client without radar detection capability (DFS Slave) , bq NIA (5250 ~ 5725 MHz was not available)

(2) Active / Passive Scanning Frequency Band | Active Scanning

(MHz) (the device can | (Where the device transmit a probe | 1s can listen only passive scanning Ad Hoc Mode or WIFI Direct canability Access point capability 2412 - 2462Mhz 9190 - 5250MAz 0200 - 9300MAZ 0470 - 5720Mhz 9/29 - 9800MAZ

\DEaCON)}

L] Yes , No Yes [| No

[1 Yes , No

[1 Yes, Dd No bd Yes , [| No With NO Prodes) L1 Yes , i No

[Yes , X{ No L1 Yes , Xt No L1 Yes , i No

[Yes , X{ No Country code selection ability -] Yes , DX No L] Yes , No

[1 Yes , X{ No L1 Yes , Xt No L1 Yes , Xt No

[1 Yes, X{ No L] Yes , No Md Yes , |} No L] Yes , No L] Yes , No Md Yes , |} No lf vas. nis aynlain how tf was inolemented : (nls also heln to nrovide cletall of ontions for each country selection)

(4) Meet 15.202 requirement - hq Yes , L] No, pls check below :

XA master device is defined as a device operating in a mode in which it has the capabilty to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices

[JA client device is defined as a device operating in a mode in which the transmissions of the device are under rantral at tha mactar A davica in cllant mada ie not ahla tn initiata 9 natwark NIWETRE NE WE REIN PEI PO ET TENA OT PI AI OR OTT AOE

(5) Forclient devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer.

[ TApply, Ves , please see SW security Description. I No Apply, (If apply, pls help to provide explanation on it HAK TAAAIARARAL ARA kai AAtGIARA GTAA AAKLPAIIAA\

Wo TWIIVIGHIGHL, GUM HUW OUIWOIG WOO UVIIVIHOU }

Signature Name (Printed): J Title: Deputy Manager ff jiang On behalf of Company: 2-Com, Inc. Telephone: +886 3 5777364 Address: SF, No.8 HSIN-ANN RD. HSINCHU SCIENCE PARK, Hsinchu, Taiwan 30078