FCC ID: 2ADM5-HP-0193 BT Endurance HP AST

Date: 7 APR 2020 Product: HP-0193 BT Endurance HP AST Table of Contents 1. Introduction 2. Packaging Contents 4. How to use END URANCE S P O R T W I R E L E S S H E A D P H O N E S INSTRUCTION MANUAL 1 Introduction 1 2 Packaging Contents 2 3 Connection Diagram 2 4 How To Use 4.1 General Function 4.2 Pairing To Mobile Phone 4.3 Charging Your Product 5 Product Specification 6 FAQ 7 FCC Statement Battery Statement 3 3 4 5 6 6 7 8 Congratulations, and thank you for choosing the Endurance Wireless Headphones. This manual will help you operate the Endurance Wireless Headphones, but firstly you should familiarize yourself with the Bluetooth functionality of your mobile phone or other devices before using the Endurance Wireless Headphones. Please follow the rules depicted in this manual closely to ensure your safety. Before using this Bluetooth headphones, we would strongly encourage you to read through this user manual. Be more wary of any edges, uneven surfaces, metal parts, accessories and its packaging so as to prevent any possible injury or damage. Do not modify, repair or dismantle this Bluetooth headphones. Doing so may result in fires, electric shocks, complete breakdown of this Bluetooth headphones, etc. All are not covered under warranty. Do not use an diluent or volatile liquid to clean the Bluetooth headphones. Do not use the Bluetooth headphones in a hazardous location. 1 X Micro USB Cable Turn on &

Enter the pairing mode Press and hold the On / Off Button for 3 seconds. After turning on, the LED indicator flashes red/blue. 1 X Endurance Wireless Headphones 1 X Instruction Manual Pairing 3. Connection Diagram Use a mobile phone with Bluetooth function or other Bluetooth devices to perform necessary pairing action. After pairing, the LED indicator slowly blinks with blue. Turn off Press and hold the On / Off Button for 4 seconds. Charging Plug the Micro USB to the Micro USB port. When charging, the LED indicator turns red. After full charging, the LED indicator turns off. Answering a Call Press On / Off button to answer phone call, press On / Off button again to end call. Press and hold 2 seconds to reject call. Double click to redial last call. Play / Pause Music Press On / Off button to play music and press it again to pause music. Power / Answer / End Call Prev / Volume Down Next / Volume Up Play / Pause LED Indicate Micro USB Charging Port 1 Microphone 4.2. Pairing to Mobile phone or other device To use your Bluetooth headphones, you must first pair your headphones with a mobile phone or other Bluetooth device. Once your Bluetooth headphones is paired to a specific mobile phone, they will remain paired and automatically recognize each other whenever they are within range. Turn on your phone and ensure the Bluetooth function is activated. Turn on the headphones, enter the pairing mode. Search your Bluetooth devices on your phone by following the phones instructions. Refer to your phones user manual for more information. After a few seconds the phone will list the BT ENDURANCE HP as a discover device. Select it and follow your phones instructions to select this pairing. Your phone will confirm the pairing, and then press Yes/OK. 4.3. Charging your headphones For your safety, please always use an appropriate 5V input charger/Adapter to charge the product. DO NOT USE Quick Charging USB Adapter to charge the product, as it might damage the product. Use the Micro USB cable accessory provided with this headphones. Connect the Micro USB plug to the Micro USB charging port on the headphones positioned at in headphones diagram on page 2. Connect the USB plug to a USB port on a computer or wall adapter to activate charging. 1

**Make sure to keep the headphones charging for a minimum of 2 hours before initial use. USB Plug Micro USB Plug Warning:

You must select a qualified charger from a regular manufacturer. You must charge the Bluetooth headphones if it has not been used for more than 6 months. 5. Product Specification Driver Diameter: 40 mm Impedance: 32 Ohms Frequency Response: 20 Hz - 20 KHz Sensitivity: 105 dB +/- 3 dB Power Supply: Li-ion Battery 3.7V 300 mAh Playing Time: 10 Hours Charging Time: 2 Hours Bluetooth Range: 32.8 Feet Micro USB Cable Included Safety instructions for the lithium battery and charging the product

-The input voltage to the product is 5V 1A. please only adopt certified appropriate charger/ adapter for charging the 7. FCC Statement FCC STATEMENT the following two conditions:

(1) This device may not cause harmful interference. that may cause undesired operation. 1. This device complies with Part 15 of the FCC Rules. Operation is subject to

-In order to charge the product in safe manner and reliable conditions,

(2) This device must accept any interference received, including interference

-Only charge the product at ambient temperatures between 10 deg C/

2. Changes or modifications not expressly approved by the party responsible for and 40 deg C/104 deg F. compliance could void the user's authority to operate the equipment.

- Do not heat above 70 deg C/158 deg F, e.g. Do not expose to sunlight NOTE: This equipment has been tested and found to comply with the limits for

-Switch off the product after use. a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

-Please note that we wont take any responsibility for any wrong designed to provide reasonable protection against harmful interference in a operation (e.g. Voltage higher than 5V) as this may result in severe injury residential installation. This equipment generates uses and can radiate radio or loss of property, and we cannot control the operating process during frequency energy and, if not installed and used in accordance with the the time the user using this product. instructions, may cause harmful interference to radio communications.

-In extreme cases, abuse or misuse of Lithium battery pack can lead to However, there is no guarantee that interference will not occur in a particular explosion, heat generation, fire development or smoke development. product. 50 deg F or throw into fire. 6. FAQ is turned on ?

1. Why is there no power even when the headphones Ans: Ensure the battery has been charged up to 1 hour for initial use. 2. There is no sound when playback. Ans: Check the connection between headphones with phone or computer, if the connection is not established, please connect again. Make sure the headphones is paired and connected with your target phone or other master device. installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: 2ADM5-HP-0193 Item # HP-0193 Distributed by 1616 Holdings, Inc. 701 Market Street, Suite 200 Philadelphia, PA 19106 Made in China Keep all relevant information for future reference

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Zeeva International Limited Suite 1007B, 10th Floor, Exchange Tower, 33 Wang Chiu Road, Kowloon Bay, Hong Kong Tel: +852-2868 0511 | Fax: +852-2524 1986 E-mail: akshay.butani@zeeva.com 04/24/2020 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, Zeeva International Limited the undersigned, hereby authorize Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature:

Printed Name: Akshay P Butani Title: Vice President QA-FR-170-B

Zeeva International Limited Suite 1007B, 10th Floor, Exchange Tower, 33 Wang Chiu Road, Kowloon Bay, Hong Kong Tel: +852-2868 0511 | Fax: +852-2524 1986 E-mail: akshay.butani@zeeva.com Date: 04/24/2020 To: FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 The RF chip, model: AC6925F, installed in our product BT Endurance HP AST

(Model number: HP-0193, FCC ID: 2ADM5-HP-0193), which support Bluetooth BDR(GFSK) , EDR(/4DQPSK), EDR(8DPSK), BLE, for use in the US marketing this chip will not support/enable the 8DPSK and BLE. And 8DPSK, BLE function has been shielded by the manufacturer by using the software. Sincerely Yours, Signature:

Printed Name: Akshay P Butani Tiltle: Vice President

Circuit description Battery (DC 3.7V) provides energy for the Bluetooth chip (AC6925F); Crystal oscillator (24MHz) pr ovides the clock signal for the Bluetooth chip. Bluetooth signals get through a matching circuit, an d then transmitted to the space through the antenna (2402-2480MHz). When the product is connected, the product can in two-way communication with other Bluetoot h Devices, and then the devices Bluetooth module sends Bluetooth signals into space, the produ ct receives the Bluetooth signal through an antenna, transmission to the Bluetooth chip via matc hing circuit. When need charging, input USB cable, and connected to the power supply, red light on, the light will change to blue light when is power up.