FCC ID: 2ADM5-EP-0654 BT SOLO BUD AST

~ SOLO WIRELESS EARBUD INSTRUCTION MANUAL Thank you for purchasing the Solo Wireless Earbud This manual provides more information about the wireless earbud, please read the instructions before using Product Overview Solo Wireless Earbud

A 1. On/Off Button!

Play/Pause Music AnswerlEnd Call Instruction Manual Package Contents Solo Wireless Earbud x1 Portable Charging Case x 1 Specifications Driver Diameter: 10 mm. Impedance: 32 Ohms Frequency Response: 20 Hz -20 KHz Sensitivity: 96 8 +/-3 48 Power Supply: L-ion Battery 3.7V 35 mAh Playtime: 6 Hours Charging Time: 3 Hours a ~

(J Ca]

XN Portable Charging Case 2. LED Indicator 3. Charging On/Off Button 4. Micro USB Charging Port _ use Plug Micro USB Plug Micro USB Charging Cable Micro USB Charging Cable x 1 Instruction Manual x 1 Bluetooth Range: 22.8 Feet Charging Case Battery Capacity: 200 mAh Micro USB Charging Cable Included Power On/Off Power On ress and hold down the On/Off Button of earbud for 3 seconds and the LED will fash, Power Off Press and hold down the On/Off Button of earbud for 4 seconds and the LED will turn off Pair the wireless earbud with your mobile device 1. Keep the distance between the earbud and mobile device within 32.8 feet. 2. De-activate the Bluetooth function on your mobile device. 3. Power on the earbud simultaneously by pressing the On/Off buttons.

{or 3 seconds and wait for 3 to 5 seconds for auto pairing. The earbud has indicator blinking alternatively in Red and Blue. The earbud will be blinking in Blue slowly when auto pairing is done successfully on the earbud. 4. Activate the Bluetooth function on your mobile device and select BT SOLO EARBUD" from the list shown, 5. After pairing is successful, the earbud will start blinking slowly in blue. Reconnect the wireless earbuds to your mobile device When powered on, the wireless earbud will automatically connect withthe last successfully paired device. Disconnect the wireless earbuds from your mobile device Power off the wireless earbud; or Switch off the Bluetooth on your mobile phone; or Leave the earbud 60ft away from your mobile phone or further. Answer / Reject a call When receive a call, press the On/Off Button once ( on either earbud) to accept the call, or answer the call normally via your mobile phone. Press and hold 2 seconds to reject it. End a call To end the call, just press On/OF button on the earbud with Beep sound to end it. Charging your Earbud with Charging case 1. Open the charging case cover. 2. Put earbud to charging case and press the charging On/Off button to start charging. 3. Earbud LED indicator light tums red when charging your earbud, 4, Earbud LED indicator ight tums off when your earbud is fully charged. Recharge Charging Case AS For your safely, please always use appropriate SV input charger/Adapter to charge the product. DO NOT USE Quick Charging USS Adapter to charge the product, st might damage the produc 1. Use the Micro USB charging cable provided with the packaging 2. Connect the Micro USB plug to Micro USB charging port on the charging case, then connect the USB plug to a USB port on a computer or wall adapter to begin charging. 3. The Red LED on the charging case will be flashing during charge 4. Once fully charged, the Red LED will be on and stop flashing, NOTE:

+ You must select a qualified charger from a regular manufacturer.

+ You must charge the charging case and earbuds iit has been not used for more than. 12 months. Mero USB Phy FAQ If the wireless earbud cannot be paired with your device, please try the following:

Ensure that your earbud is in pairing mode or reconnection mode Ensure that Bluetooth search function of your mobile device is activated I the wireless earbud will not turn on:

Make sure the earbud is fully charged. Can I change the battery for the charging case and earbud?

The charging case and earbud use a builtin non-detachable battery which cannot be removed, I the charging case cannot be recharged:

Ifyou use a power outlet, ensure that the power supply is connected securely and the outlet works. If you use a computer, ensure that itis connected and the USB port is powered. 4 Safety instructions for the lithium battery and charging the product The input voltage to the product is 5V 1A.

-In order to charge the product in safe manner and reliable conditions, please only adopt certified appropriate charger! adapter for charging the product.

-Only charge the product at ambient temperatures between 10 deg C/ 50 deg F and 40 deg C/104 deg F.

- Do not heat above 70 deg C/158 deg F, eg. Do not expose to sunlight or throw into fire.

-Switch off the product after use.

-Please note that we wor't take any responsibilty for any wrong operation (eg. Voltage higher than 5V) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product. In extreme cases, abuse or misuse of Lithium battery pack can lead to explosion, heat generation, fire development or smoke development. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to ty to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

= Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

~ Consult the dealer or an experienced radio/TV technician for help. RF waming statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCCID: 2ADM5-EP-0654 Keepall relevant information for future reference ITEM# EP-0654

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ3210702-26839E-RF EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Zeeva Int

Suite 1007

Road,Kow

Tel: +852

E-mail: a

ternational Lim

7B, 10th Floor

wloon Bay, Ho

2-2868 0511 |

akshay.butan

mited

, Exchange To

ng Kong

Fax: +852-25

ni@zeeva.c

524 1986

com

ower, 33 Wang

g Chiu

Dat

To:

Aut

743

We

Pro

Mo

FCC

For

For

Blu

Exc

mo

ma

com

Sinc

Sign

Prin

Tilt

te: 2021/0

07/19 

 FEDERAL

thorizatio

35 Oaklan

 COMMU

n and Eva

d Mills Ro

NICATION

luation Di

oad Colum

NS COMMI

ivision  

mbia, MD 2

21046  

ISSION   

nal Limited

LO BUD AS

d  hereby d

ST 

declare th

hat： 

e, Zeeva In

oduct Nam

odel No.: E

C ID: 2ADM

r BT Mode

nternation

me: BT SOL

P‐0654 

M5‐EP‐065

e:   BLE 1M

54 

M/2M are 

disable by

e 

y software

r Below ar

etooth ED

re activate

DR((π/4‐D

ed:  

QPSK),BD

R(GFSK)  ,

,EDR(8DPS

SK) 

cept for th

odify/chan

nufacture

mpliance w

he manufa

nge the RF

er’s respon

with Comm

acturer, th

 paramete

nsibility to

mission’s 

he end use

ers. We ac

o provide t

rules. 

er does no

cknowledg

the radio 

ot have an

ge that it 

configura

y capabilit

is the 

tions to e

ty to 

nsure 

cerely You

nature:     

nted Nam

le: Vice Pr

urs, 

e: Akshay

resident 

y P Butani

Circuit description for energy chip(AC6969);

the Bluetooth Crystal Battery(3.3-4.2V)provides oscillator(24MHz) provides the clock signal for the Bluetooth chip. Products is in broadcasting state when stand by, broadcasting Bluetooth signals according to a certain time interval. Bluetooth signals get through a matching circuit, and then transmitted to the space through the antenna(2402MHz-2480MHz). When the product is connected, the product can be in two-way communication with mobile phones, and then the phone's Bluetooth module sends Bluetooth signals into space, the product receives the Bluetooth signal through an antenna, transmission to the Bluetooth chip via matching circuit.

Zeeva Int

Suite 100

Road, Ko

Tel: +852

E-mail: a

ternational Lim

07B, 10th Floo

owloon Bay, H

2-2868 0511 |

akshay.butan

mited

or, Exchange T

Hong Kong

Fax: +852-25

ni@zeeva.c

524 1986

com

Tower, 33 Wa

ang Chiu

2021

1/07/19

The

Asso

Acc

for t

FCC

Refe

The

belo

A. S

to af

B. T

the p

Zeeva Intern

ociated User

ording to the

the FCC ID t

C ID to be pr

erring to the

FCC ID wil

ow:

Side surface (

ffix the label

Top cover (B

printing of th

CC ID C

FC

mited here by

national Lim

r Manual.

e FCC Regul

to be moved

rinted.

above quote

ll be moved t

lation and Gu

to the User’

e, as the devi

to the last pa

Cover Le

y submits ju

etter

stification fo

or placing the

e FCC ID in

the

uidance (KD

s manual if t

DB Publicatio

the device is

on 784748 D

unquestiona

D01 v09r01) a

ably too smal

allows

ll for the

ice is too sma

age of user’s

all (FCC ID:

manual and

: 2ADM5-EP

charging cas

P-0654) to be

se. The detai

e printed.

ls are as

(A): The cur

l on the surfa

): The plastic

he FCC ID ac

rvature shape

ace of the ear

c logo of the

ccording to b

e of the silico

rbuds.

e top cover do

below referen

oes not prov

nce picture.

one sleeve ba

ack cover is n

not flat, so it

t’s hard

vide enough p

physical spac

ce to fit

A

B

ove descripti

ng the FCC I

User manual

ion of area A

ID to be prin

and charging

A to B, we co

nted onto any

g case

onclude that t

y surface, We

the device is

e therefore r

unquestiona

request to m

ably too

ove the

Con

Base

sma

FCC

nclusion：

ed on the abo

all for enablin

C ID to the U

Sinc

cerely Your

rs,

Sign

nature:

Prin

nted Name:

Akshay P B

Butani

Titl

e: Vice Pr

resident