ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net
- 1 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net CATALOG Features3 Technique Parameters.4 Pin Description Pin.5 Dimension.6 Circuit Description..7 Module Pinout.8 Amplifier Application Circuit9 Operation Amplifier Application Circuit..10
- 2 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Features OVC3960 is a high integration, low cost, low power Bluetooth stereo audio module Fully qualified Bluetooth version 3.0 module Supports A2DP V1.3, AVRCP V1.5, HSP1.2, HFP1.6 profiles Integrated EEPROM, deploys operational mode and parameters Internal MIC bias voltage supply Internal MIC amplifier UART supports caller ID display (only when the phone terminal supports the function) Differential stereo audio output Audio output can drive 40mW @ 32speeker, but not need the blocking power Integrated reset circuit and programmed low voltage monitoring function 5 key output, including On/Off, Connection, Play, Pause/Louder/Lower/Previous/Next 2 indicators to guide 2 different function modes Provides a warning tone when a call coming and plays ring tone when the phone terminal supports it Short press ONKEY to answer or hold off the call, long press can reject the call, extended press can stop the phone connection, and short press twice can dial the last dialed call
- 3 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Technique Parameters
- 4 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net PIN Description Name RESET VDD33 L_PAOUTN L_PAOUT R_PAOUT R_PAOUTN MIC_L MICBIAS
---
LED1 LED2 VOL +
VOL-
ONKEY VCC +5V GND BAT UART_RX UART_RX PCM_OUT PCM_IN PCM_CLK PCM_SYNC MUTE Prev Next NC ANT Mode Digital Power Audio Audio Audio Audio Audio Power
---
Sink Sink Digital Digital Digital Power Power Power Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital
---
Description Compatible with I2C Data information Power output, supplys power to indicator 1,2 MIC Input MIC Bias Voltage output
---
Control terminal of indicator 1 Control terminal of indicator 2 Increase Volume, Next Song Lower Volume, Previous Song Turn on/off, Play/Pause Power Charge Terminal +5V Ground Battery Power Charge Terminal 3.7V-4.2V UART receive input UART transmit input PCM interface PCM interface PCM interface PCM interface Play/Pause, high/low output Previous song Next song Compatible I2C Timer Connect the external antenna No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
- 5 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Dimension
- 6 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Circuit Description Module Application Schematic
- 7 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Module Pinout
- 8 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Amplifier Application Circuit Single-ended Amplifier Application Double-ended Amplifier Application
- 9 - / 10 ZhongshanHuaxingLightingCO.,LTD. ADD:GuErShunChengIndustrialZone,GuZhen,ZhongShanCity,GuangDong,P.R.China
(Tel):8676022323667(Fax):867602323665 Email:hualamps@163.net Operation Amplifier Application Circuit
- 10 - / 10 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
To comply with FCC RF exposure compliance requirements, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions:
(1) According to FCC Part 15 Subpart C Section 15.212, the radio elements of the modular transmitter must have their own shielding. This module is granted as a Limited Modular Approval.
(2) This device has been designed to operate with a PCB antenna which having a maximum gain of -4.4dBi. Only this type of antenna may be used.
(3) Integration is typically strictly restricted to Grantee himself or dedicated OEM integrators under control of the Grantee. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: If the module which installed in the end product has no shielding, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Due to missing shielding the module is strictly limited to integration by the Grantee himself or his dedicated OEM Integrator. USER MANUAL OF THE END PRODUCT:
In the user manual of the end product, the end user has to be informed that the equipment complies with FCC radio-frequency exposure guidelines set forth for an uncontrolled environment. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the user manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following" Contains TX FCC ID: 2AEEB-HX3960BT ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.