Printer Parts Front of Printer Basic Operation Label Cartridge Cover
Take out Ribbon: Pull ribbon locking bar to unlock, take the ribbon out. Install Ribbon: Pull ribbon locking bar to unlock, insert ribbon to the bottom of ribbon compartment, hold it by hand and pull ribbon locking bar to lock. Connect with Printer
Scan QR Code on the right side, download label editing App WeiDa Label (Android, iOS) Label Exit Slot Paper Tear-off Knife
Press power button for 1.5s to turn the printer on. Ribbon Compartment OLED Display Feed Button Power Button Side of Printer
Label size: Label printing side outward, diameter of label roll is less than 65mm ( must not more than 67mm ), label width 12~54mm, maximum width 54mm ( including base paper ). Install paper: Put label roll into the cartridge. Please make sure the label printing side face down, move label adjusting plate to appropriate position according to labels width, insert front end of label into label guiding slot , press feed bottom simultaneously to locate position.
Turn on printer-turn on mobile phone Bluetooth-open label editing App, click No Printer Connected. Then you can edit your label and print it. If the printer hasnt paired before, click search button, then the unpaired printer will be listed. Select unpaired printer, WeiDa will pair with it automatically, enter password and connect with printer. Built-in Ribbon Back of Printer USB Interface Power Supply Interface Ribbon Locking Bar
( Print Head Locking Bar ) Lock Unlock Battery Compartment Cover
Label paper: short press feed button to feed one label to the beginning of next label; long press feed button to feed label continuously, release the feed button to stop at the beginning of next label. Continuous paper: press feed button to start feeding label, release feed button to stop feeding.
Printer will shut down automatically if no use it for a long period. Time of automatic shutdown can be set by setting button, the default time is 15 minutes.
Short press power button, printer enters setting status when the icon appears on the top left corner of display, then press feed button to make corresponding options.
Printer can provide 5V ( 500mA ) power for external devices via power supply interface, like phone, Pad, etc. DT60S
Please consult your supplier for account password of cloud catalogue. Log in your account to choose template you need from cloud catalogue, click it to use, modify then save the template. In this case, you can choose and print it directly from the cloud catalogue next time. FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Specifications Safety Notices
Maintenance
OLED display Thermal transfer line Black and white 203 DPI/300 DPI (optional) 384 dots/line 15 ~ 50 mm/s 150 ~ 180 m (12.5% print darkness) About 5 years (power off) 2600 mAh 5V USB 6 ~ 7 h Support Self-adhesive paper Roll paper 54(W) dia.65 mm 48 mm 0.05 ~ 0.15 mm 725 g IP54 0 ~ 45 205 (L) 106 (W) 78 (H)mm
Power adapter, battery, ribbon, USB cable Micro USB, Bluetooth (Android, iOS), 2.4G WiFi (optional) LPAPI ,CPCL, ESC/POS compatible with instruction sets Reflection-Type, Correlation (optional)
Cover open, paper out, low battery, overtemperature
Text, picture, line, graphics 1D Barcode: CODE-39, CODE-128, EAN, UPC, other common ones 2D Barcode: QR Code, PDF417, DataMatrix UHF RFID900MHzcompatible with ISO18000-6C / EPC Gen2 (optional) HF RFID 13.56MHz14443-A / 15693 / NFC (optional) Please shut down the printer first