FCC ID: 2AOKB-T8130 eufyCam Solo, eufyCam Solo Pro

1 WHATS INCLUDED QUICK START GUIDE eufyCam Solo / Solo Pro eufyCam Solo / Solo USB Cable Pro Model: T8130/T8131 Mounting Bracket 5 Recommended:

Mounting Screw Pack Quick Start Guide Normal Charging:

2 PRODUCT OVERVIEW eufyCam Solo / Solo Pro 1 2 3 4 6 7 8 1. LED Indicator 2. Camera Lens 3. Microphone 4. Motion Sensor 5. Photosensitive Sensor 9 3 CHARGING YOUR EUFYCAM SOLO / SOLO PRO SETTING UP EUFYCAM SOLO / SOLO PRO 4 MOUNTING 5 THE INDOOR CAM Mount eufyCam Solo / Solo Pro eufyCam Solo / Solo Pro can be mounted both outdoors and indoors. 1. Turn the knob of the mounting bracket clockwise to loosen and disassemble it. eufyCam Solo / Solo Pro comes with a built-in battery. Before setup, fully charge your eufyCam Solo / Solo Pro using the provided micro USB cable. 1. Download the eufy Security app from the App Store (iOS devices) or Google Select a Location Play (Android devices). eufyCam Solo / Solo Pro can be mounted on a wall or ceiling. Select a location where you can get the desired view. We recommend hanging it 7-10 ft (2-3 m) above the ground. 2. Place the mounting bracket against the wall. Drill holes with a 15/64 inch

(5.99 mm) drill bit, then insert the anchors into the holes; anchors are necessary for walls that are made out of hard materials such as concrete, brick, or stucco. 6. SD Card Slot 7. Micro USB Charging Port 8. Mounting Hole 9. SYNC Button Press for 2s to enter setup mode Press for 10s to reset Solid blue Charging Fully charged Off 01 02 03 04 05 06 2. Sign up a eufy Security account. Go to the app homepage. Tap Add Device, and add eufyCam Solo / Solo Pro to the system. 3. Follow the on-screen instructions to complete the setup. Note: Make sure your eufyCam Solo / Solo Pro is connected to the HomeBase. LED Status Status Ready for setup LED Indicator Flashing blue Successfully paired Off Live streaming or recording Solid red (When LED is enabled) An alarm triggered Flashing red Firmware updating Flashing blue and red alternately Camera field Camera field of view of view t f 0 1

7

) m 3

2

Motion Motion Detection Detection Zone Zone Up to 30 ft (10 m) 3. Firmly screw the base of the mounting bracket onto the wall. Fasten the ball knob of the bracket to the base of the bracket. 4. Tighten eufyCam Solo / Solo Pro to the mounting bracket. Rotate the eufy Indoor Cam to adjust the view and check it using the live stream which you can access in the eufy Security app. eufyCam Solo / Solo Pro can be also installed on the ceiling. Follow the steps 1-4 mentioned above to install it. You are now all set to use your eufyCam Solo / Solo Pro. Tips:

For troubleshooting, check Help on the eufy Security app. Refer to the app page for LED indicator status. 6 NOTICE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/

TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20 cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party. Company Name: POWER MOBILE LIFE, LLC Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541 Telephone: 1-800-988-7973 This product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: https://www.eufylife.com/. This product can be used across EU member states. Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The adapter shall be installed near the equipment and shall be easily accessible. Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for T8130 and accessories is 0C-40C. When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 5C~25C. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Wi-Fi Operating Frequency Range: for CE-RED: 2412~2472MHz; Wi-Fi Max Output Power:16.83dBm(EIRP) For FCC-ID 2412~2462MHz; Wi-Fi Max Output Power:21.47dBm Bluetooth Operating Frequency Range: 2402~2480MHz; Bluetooth Max Output Power: for CE-RED5.66dBm (EIRP), for FCC-ID: 7.054dBm The following importer is the responsible party (contact for EU matters only) Importer: Anker Technology (UK) Ltd Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. Customer Service Warranty 12-month limited warranty IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device."

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. Call Us United States

+1 (800) 988 7973 Mon-Fri 9AM-5PM (PT) United Kingdom

+44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT) Germany

+49 (0) 69 9579 7960 Mon-Fri 6:00-11:00 Email Us Customer Support: support@eufylife.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

@EufyOfficial

@EufyOfficial

@EufyOfficial Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005002284 V01 07 08 09 10 11 12

Label Location On EUT Label Model No.: T8130 Product Name: eufyCam Solo, eufyCam Solo Pro FCC ID: 2AOKB-T8130 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Anker Innovations Limited Declaration concerning Antenna Specification It is hereby declared that the product Model No.: T8130, T8131 FCC ID : 2AOKB-T8130 fulfills the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for internal antenna type(s) described below:

Model No. of antenna: T8130 Type of antenna:

Gain of the antenna:

PIFA Antenna 0 dBi Frequency range:

2402MHz~2480MHz;

2412MHz~2462MHz The mounting of the antenna is fixed to the radio module and no other antenna should be used. Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong City:

ZIP / Postal code: N/A Country:

Hong Kong Kowloon Kowloon Date: 2020-08-11 Place:

Signature:

version01