FCC ID: 2AOKB-T8210 Video Doorbell 2K (Battery-Powered) with 2.4G WiFi

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 5100500XXXX V01 Quick Start Guide Battery-Powered Video Doorbell (Add-on Unit) TABLE OF CONTENTS Whats Included 02 10 Mounting The Bracket Product Overview 03 13 Mounting The Doorbell How The System Works 04 14 Detaching The Doorbell Verifying Your Homebase 05 15 Charging The Doorbell Adding The Doorbell To Your Existing System 05 16 Powering The Doorbell With Existing Doorbell Wires Determining The Power Option 06 24 Notice Finding A Mounting Spot 08 27 Customer Service English 01 WHATS INCLUDED PRODUCT OVERVIEW For Video Doorbell Installation Video Doorbell (Battery Powered) Video Doorbell Mounting Bracket Screw Hole Positioning 15 Mounting Wedge Card

(Optional) Model: T8210 FCC ID: 2AOKB-T8210 IC: 23451-T8210 Jumper for Original Chime (Optional) Extension Wires and Wire Nuts (Optional) USB Charging Doorbell Detaching Cable Pin QSG Screw Packs (Spare screws and anchors are included) Quick Start Guide Note: Power adapter plug varies by region. 02 English 2 4 6 Front view:

Rear View:

1. Motion Sensor 2. Microphone 3. Camera Lens 4. Ambient Light Sensor 5 5. LED Ring 6. Doorbell Button 7. Speaker 1. Micro USB Charging Port 2. SYNC/RESET Button 3. Power Terminals for Existing Doorbell Wire 4. Detaching Mechanism 1 3 7 1 2 3 4 Operation How-to Power on/ Add doorbell to HomeBase Press and hold the SYNC button until you hear a beep. Power off the doorbell Quick-press the SYNC button 5 times in 3 seconds. Reset the doorbell Press and hold the SYNC button for 10 seconds. English 03 HOW THE SYSTEM WORKS STEP 1 VERIFYING YOUR HOMEBASE How the System Works Verify Your HomeBase The video doorbell system includes 2 parts. One is the video doorbell at your door. The other is the HomeBase in your house. The battery video doorbell cannot work without a HomeBase or eufyCam series system. Make sure you have an existing eufyCam series system installed and working. The video doorbell detects motion at your porch and allows you to answer the door anytime and anywhere.The HomeBase stores video clips on its built-in storage. When someone rings the doorbell, people in the house will be notified. Your video doorbell will be connected to the network where the Homebase is connected to, and added to the existing HomeBase system. Video clips captured at your door will be saved and viewed using the system. Doorbell Chime STEP 2 ADDING THE DOORBELL TO YOUR EXISTING SYSTEM Add the Doorbell to Your Existing System 1. Log into the EufySecurity App. add the doorbell to the HomeBase. 2. Tap Add Device - Battery Doorbell on the Home screen. Follow the onscreen instructions to Video Doorbell 04 English English 05 STEP 3 DETERMINING THE POWER OPTION Option 2 - Doorbell Wire Powered Option 1 - Battery Powered 1. If you dont have existing doorbell wiring at the front door, use the built-in battery. You are free to determine the doorbell position and the mounting is easy and quick. 2. When the doorbell battery level is low, you need to detach and charge it. 3. If you choose this option, please jump to STEP 4 FINDING A MOUNTING SPOT. 1. If you have existing and working doorbell wiring at the front door, the doorbell will be powered by the wires constantly. So you dont need to detach and charge it after installation. 2. Since the doorbell is connected to the wires, the mounting position is limited. 3. If you choose this option, please jump to Appendix 3 Powering the Doorbell with Doorbell Wires. 8-24VAC Doorbell Wiring 6 months Note: The battery life varies depending on usage. In most common cases, a doorbell may have up to 10 events per day and each recording lasts 20 seconds on average. Under this scenario, the doorbell battery life can last up to 6 months. 06 English English 07 STEP 4 FINDING A MOUNTING SPOT Place the Screw Hole Positioning Card against the wall to mark the position. Find a Mounting Spot Take the video doorbell to your front door and check the live view on the App at the same time. Find a location where you can get the desired field of view. Consider the below factors:

1. Check if you can reuse the existing holes and anchors on the wall or door frame. 2. If the doorbell is close to a wall, make sure the wall doesnt occupy 25% of the field of view. Otherwise the night vision will be affected. 3. If you are drilling the mounting holes for the first time, the recommended mounting height is 4. Use the 15 mounting wedge as a supplementary mounting bracket if you wish to see more 48" / 1.2 m from the ground. on a specific side. 1.76m(59) 1.2m (48") 1m

(40") 0.3m

(12") Door Video Doorbell Door Video Doorbell 15 Without 15 Mounting wedge With 15 Mounting wedge 08 English English 09 STEP 5 MOUNTING THE BRACKET Mount the Doorbell on a Wooden Surface If youre mounting the doorbell on a wooden surface, you dont need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall, the Screw Hole Positioning Card indicates the position of the screw holes. What is required: screwdriver, Mounting Bracket, 15 Mounting Wedge (Optional), Screw Pack Mount the Doorbell on Surfaces Made Out of Hard Materials 1. If youre mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with a 15/64(6mm) drill bit. 2. Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall. What is required: Power Drill, 15/64(6 mm) Drill Bit, Mounting Bracket, 15 Mounting Wedge (Optional), Screw Pack Phillips-Head Screwdriver

(User provides it.) Mounting Bracket

(Attached to 15 Mounting Wedge) 15 Mounting Wedge (Optional) Screw Packs (Spare screws and anchors are included.) Power Drill with 1/4" (6.35mm) Drill Bit

(User provides it.) 15/64(6 mm) Drill Bit

(Attached to 15 Mounting Mounting Bracket Wedge) 15 Mounting Wedge (Optional) Screw Packs (Spare screws and anchors are included.) Wall Mounting Bracket Wall Mounting Wedge Mounting Bracket Without 15 Mounting Wedge With 15 Mounting Wedge 10 English 1 English 11 STEP 6 MOUNTING THE DOORBELL Mount the Doorbell Align the doorbell on top and then snap it on the bottom. Press it down until it clicks into place. Wall Mounting Bracket Wall Mounting Wedge Mounting Bracket Without 15 Mounting Wedge With 15 Mounting Wedge 2 2 Youre all set!

If you want to detach the doorbell or recharge it, please refer to the following sections. 12 English English 13 APPENDIX 1 DETACHING THE DOORBELL APPENDIX 2 RECHARGING THE DOORBELL Detach the Doorbell What is required: Doorbell Detaching Pin Recharge the Doorbell Doorbell Detaching Pin 14 English English 15 LED indication Charging: Steady blue Fully charged: Off Charging time 6 hours APPENDIX 3 POWERING THE DOORBELL WITH EXISTING DOORBELL WIRES What is required: Philips-Head Screwdriver 3.1 Verify whether the doorbell wires are working 1. Ring the existing doorbell to check if it is working. 2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the electricity in your house is properly shut off. Phillips-Head Screwdriver

(User provides it.) OFF OFF Always be careful when handling wires. If youre not comfortable installing it yourself, have a qualified electrician do it. 3.2 Detach the Existing Doorbell Button If you already have existing doorbell wiring:

1. Remove the existing doorbell button with a Phillips-Head screwdriver (not provided). if necessary. 16 English 3.3 Find a Mounting Spot 1. Determine the mounting position of the doorbell. Consider the below factors:

Check if you can reuse the existing holes and anchors on the wall or door frame. If you are drilling the mounting holes for the first time, the recommended mounting height is 48" / 1.2 m from the ground. more on a specific side. English 17 2. Pull the two wires out carefully when removing the existing doorbell. Straighten the wire ends Use the 15 mounting wedge as a supplementary mounting bracket if you wish to see 3.4 Mount the Bracket 15 If youre mounting the doorbell on a wooden surface, you dont need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The Screw Hole Positioning Card indicates the position of the screw holes. What is required: Power Drill, Mounting Bracket, 15 Mounting Wedge (Optional), Screw Pack 1.76m(59) 1.2m (48") 1m

(40") 0.3m

(12") Door Video Doorbell Door Video Doorbell Without 15 Mounting wedge With 15 Mounting wedge 2. Place the Screw Hole Positioning Card against the wall to mark the position. Phillips-Head Screwdriver

(User provides it.) Mounting Bracket

(Attached to 15 Mounting Wedge) 15 Mounting Wedge (Optional) Screw Packs (Spare screws and anchors are included.) Wall Mounting Bracket Wall Mounting Wedge Mounting Bracket Without 15 Mounting Wedge With 15 Mounting Wedge 18 English English 19 If youre mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco:

Drill 2 holes through the Screw Hole Positioning Card with 15/64(6mm) drill bit. Insert the provided anchors, and then use the provided screws to secure the Mounting Bracket on the wall. What is required: Power Drill, 15/64(6mm) Drill Bit, Mounting Bracket, 15 Mounting Wedge (Optional), Screw Pack Power Drill with 1/4" (6.35mm) Drill Bit

(User provides it.) 15/64(6 mm) Drill Bit

(Attached to 15 Mounting Mounting Bracket Wedge) 15 Mounting Wedge (Optional) Screw Packs (Spare screws and anchors are included.) Wall Mounting Bracket Wall Mounting Wedge Mounting Bracket Without 15 Mounting Wedge With 15 Mounting Wedge 2 2 1 20 English English 21 3.5 Connect the Doorbell Wires to the Doorbell 3.6 Mount the Doorbell on the Bracket Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal. What is required: Wires and Wire Nuts (Optional) / Video Doorbell / Philips-head Screwdriver Align the doorbell on top and then snap it on the bottom. Extension Wires and Wire Nuts (Optional) Video Doorbell 2K

(Wired) Phillips-Head Screwdriver

(User provides it.) 3.7 Restore Power Switch the master circuit breaker back to ON. ON ON Note:

To prevent short-circuit, make sure the wires are not touching each other after connecting them to the terminals. If the wires are too short, use the extension wires and wire nuts provided to make them longer. Use electrical wiring tape instead if there is no more space on the wall for wire nuts. Youre all set!

If you want to detach the doorbell or recharge it, please refer to the corresponding sections. 22 English English 23 NOTICE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/ TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. FCC ID:2AOKB-T8210 The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541 Telephone:1-206-383-8247 24 English This product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.For the declaration of conformity, visit the Web site:https://www.eufylife.com/. This product can be used across EU member states. Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for HomeBase 2 and accessories is -20C-50C. When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 5C~25C. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Wi-Fi Operating Frequency Range:2412~2472MHz ; Wi-Fi Max Output Power:17.62dBmEIRP The following importer is the responsible party (contact for EU matters only) Importer: Anker Technology (UK) Ltd Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. English 25 IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device."

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. CUSTOMER SERVICE Warranty 12-month limited warranty Call Us United States +1 (800) 988 7973 Mon-Fri 9AM-5PM (PT) United Kingdom +44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT) Germany +49 (0) 69 9579 7960 Mo-Fr 6:00-11:00 Email Us Customer Support: support@eufylife.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong 26 English English 27

Red area: silk screen PT 877C Blue area: purple laser engraving

Red area: silk screen PT 877C Blue area: purple laser engraving

Anker Innovations Limited Date: 2019/11/13 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

Innovations Limited, The Anker the undersigned, hereby authorizes Mrs. Catherine Chen from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the Anker Innovations Limited solely in matters relating to the application for an FCC equipment authorization for FCC ID:2AOKB-T8210 including the signing of documents in connection with this Application. Necessary acts carried out Shenzhen Morlab Communications Technology Co., Ltd. on our behalf of the Anker Innovations Limited in connection with the Application shall have the same effect as acts of the Anker Innovations Limited.Anker Innovations Limited also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Thank you for your attention to this matter. Yours Sincerely, Signatory:

Contact name: louis Qi Title:NA Tel:+86-13652441319 Email:louis.qi@oceanwing.com Company name: Anker Innovations Limited

Anker Innovations Limited Date: 2019/11/13 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: Request of Confidentiality for FCC ID: 2AOKB-T8210 To Whom it may concern:

Pursuant to sections 0.457 and 0.459 of Commissions Rules(CFR 47), and Section 552(b)(4) of the Freedom of Information Act, Anker Innovations Limited hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after grant as outlined in Public Notice DA04-1705. This provision will give Anker Innovations Limited temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows:

PERMANENT AND SHORT-TERM CONFIDENTIAL LIST Description Block Diagram Exhibit PERMANENT SHORT-TERM 1 2 3 4 5 6 7 8 Operational Description Schematics BOM External Photos Internal Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Signatory Namelouis Qi Company nameAnker Innovations Limited AddressRoom 1318-19,Hollywood Plaza,610 Nathan Road,Mongkok,Kowloon,Hong Kong Tel+86-13652441319 Emaillouis.qi@oceanwing.com

Declaration To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID:2AOKB-T8210 Don't operate on Channels 12 and 13. US 2.4G channel 12-13 and Country code selection are disabled through proprietary software and are not user changeable Should you have any questions, please feel free to contact me Signature :

Job Title and Dept.

: Manager/R&D