FCC ID: BCGA1513 Siri Remote

Remote Apple Confidential Using Your Apple Remote - content to come Use your Apple Remote with Apple products that have a built-

in infrared (IR) receiver. Play a DVD or music from your iTunes library, watch photo slideshows and movie trailers, and more. Left Select Up Right Down Menu Play/Pause To use your remote:

Press Play/Pause to play or pause a song, slideshow, or movie. Press Right or Left to skip to the next or previous song in your iTunes library, or to the next or previous chapter on a DVD. Hold down Right or Left to fast-forward or rewind a song or movie. Press Up or Down to adjust the volume of a Mac or iPod dock (but not the volume of an Apple TV). Pairing Your Apple Remote You can pair your Apple Remote with a specific Mac or Apple product. After you pair the Mac or Apple product, its controlled by only the paired remote. To pair your remote:

1 Move within 3 to 4 inches (8 to 10 cm) of your Mac or Apple product. 2 Point the remote at the IR receiver on the front of your Mac or Apple product. 3 Hold down Right and Menu for 6 seconds. When youve paired your remote, a chainlink symbol appears onscreen. 2 Apple Confidential To unpair your remote on a Mac:

1 Choose Apple () > System Preferences from the menu bar. 2 Click Security & Privacy, click Advanced, and then click Unpair. To unpair your remote on other Apple products:

Hold down Menu and Left for 6 seconds. Charging the remote Content to come. 3 Apple Confidential Regulatory Compliance Information FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Important: Changes or modifications to this product not authorized by Apple could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority to operate the product. This product has demonstrated EMC compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions, and other electronic devices. This product was tested for EMC compliance under conditions that included the use of Apple peripheral devices. Responsible party (contact for FCC matters only):

Apple Inc. Corporate Compliance 1 Infinite Loop, MS 91-1EMC Cupertino, CA 95014 Industry Canada Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subjectto the following two conditions: (1) this device may not cause interference, and (2) this devicemust accept any interference, including interference that may cause undesired operation ofthe device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareilsradio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1)lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter toutbrouillage radiolectrique subi, mme si le brouillage est susceptible den compromettrele fonctionnement. CAN ICES-3 (B)/NMB-3(B) 4 Apple Confidential VCCI Class B Statement EU Compliance Statement Apple Inc. hereby declares that this wireless device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive. A copy of the EU Declaration of Conformity is available at:

www.apple.com/euro/compliance Apples EU representative is: Apple Distribution International, Hollyhill Industrial Estate, Cork, Ireland N122 Russia, Kazakhstan, Belarus Battery Information The built-in lithium-ion battery should be serviced by Apple or an authorized service provider, and must be recycled or disposed of separately from household waste. For information about batteries, go to www.apple.com/batteries. Singapore wireless certification Disposal and Recycling Information This product and/or battery should not be disposed of with household waste. When you decide to dispose of this product and/or its battery, do so in accordance with local environmental laws and guidelines. For information about Apples 5 Apple Confidential recycling program, recycling collection points, restricted substances and other environmental initiatives, visit www.apple.com/environment. Informacin sobre eliminacin de residuos y reciclaje El smbolo indica que este producto y/o su batera no debe desecharse con los residuos domsticos. Cuando decida desechar este producto y/o su batera, hgalo de conformidad con las leyes y directrices ambientales locales. Para obtener informacin sobre el programa de reciclaje de Apple, puntos de recoleccin para reciclaje, sustancias restringidas y otras iniciativas ambientales, visite http://www. apple.com/la/environment. BrasilInformaes sobre descarte e reciclagem O smbolo indica que este produto e/ou sua bateria no devem ser descartadas no lixo domstico. Quando decidir descartar este produto e/ou sua bateria, faa-o de acordo com as leis e diretrizes ambientais locais. Para informaes sobre substncias de uso restrito, o programa de reciclagem da Apple, pontos de coleta e telefone de informaes, visite www.apple.com/br/environment. European UnionDisposal Information The symbol above means that according to local laws and regulations your product and/or its battery shall be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. The separate collection and recycling of your product and/or its battery at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. Union Europenneinformations sur llimination Le symbole ci-dessus signifie que, conformment aux lois et rglementations locales, vous devez jeter votre produit et/ou sa batterie sparment des ordures mnagres. Lorsque ce produit arrive en fin de vie, apportez-le un point de collecte dsign par les autorits locales. La collecte spare et le recyclage de votre produit et/ou de sa batterie lors de sa mise au rebut aideront prserver les ressources naturelles et sassurer quil est recycl de manire protger la sant humaine et lenvironnement. Europische UnionInformationen zur Entsorgung Das oben aufgefhrte Symbol weist darauf hin, dass dieses Produkt und/oder die damit verwendete Batterie den geltenden gesetzlichen Vorschriften entsprechend und vom Hausmll getrennt entsorgt werden muss. Geben Sie dieses Produkt zur Entsorgung bei einer offiziellen Sammelstelle ab. Durch getrenntes Sammeln und Recycling werden die Rohstoffreserven geschont und es ist sichergestellt, dass beim Recycling des Produkts und/oder der Batterie alle Bestimmungen zum Schutz von Gesundheit und Umwelt eingehalten werden. Unione Europeainformazioni per lo smaltimento Il simbolo qui sopra significa che, in base alle leggi e alle normative locali, il prodotto e/o la sua batteria dovrebbero essere riciclati separatamente dai rifiuti domestici. Quando il prodotto diventa inutilizzabile, portalo nel punto di raccolta stabilito dalle autorit locali. La raccolta separata e il riciclaggio del prodotto e/o della sua batteria al momento dello smaltimento aiutano a conservare le risorse naturali e assicurano che il riciclaggio avvenga nel rispetto della salute umana e dellambiente. 6 Apple Confidential Europeiska unionenInformation om kassering Symbolen ovan betyder att produkten och/eller dess batteri enligt lokala lagar och bestmmelser inte fr kastas tillsammans med hushllsavfallet. Nr produkten har tjnat ut mste den tas till en tervinningsstation som utsetts av lokala myndigheter. Genom att lta den uttjnta produkten och/eller dess batteri tas om hand fr tervinning hjlper du till att spara naturresurser och skydda hlsa och milj. Trkiye Cumhuriyeti:

AEEE Ynetmeliine Uygundur Apple and the Environment At Apple, we recognize our responsibility to minimize the environmental impacts of our operations and products. For more information, go to: www.apple.com/environment 7 Apple Confidential 2015 Apple Inc. All rights reserved. Apple, the Apple logo, Apple TV, iPod, iTunes, and Mac are trademarks of Apple Inc., registered in the U.S. and other countries. Printed in XXXX. 034-00750-A Apple Confidential

A1513 Front Panel - Back Side Apple Proprietary and Confidential A1513 A1513 Front panel opened Apple Proprietary and Confidential A1513 PCB Front Apple Proprietary and Confidential A1513 PCB Back Apple Proprietary and Confidential A1513 PCB Front, with antenna covering material removed BTLE Radio IC BTLE Antenna Apple Proprietary and Confidential A1513 With PCB Removed Apple Proprietary and Confidential A1513 Battery and Charging Connector Assembly - Back Apple Proprietary and Confidential A1513 Battery and Charging Connector Assembly - Front Apple Proprietary and Confidential

A1513 Front:

Microphone, Buttons - Menu, Watch, Volume Up/

Down, Voice Assistant (Siri), Play/Pause. Trackpad with Button p le C p A n tia l e d n o A1513 Right Side Apple Condential A1513 Top Side - Infrared LED Window n tia l e d n o p le C p A A1513 Left Side A p ple C ond ential A1513 Bottom Side - Lightning connector n tia l e d n o p le C p A A1513 Back Plate -

Microphone n tia l e d n o p le C p A

A1513 - Backplate Regulatory Label Apple Proprietary and Confidential

To Whom It May Concern:

Subject: Appropriateness of Pre-Production Sample for Certification Testing We hereby confirm that the pre-production sample(s) provided for certification testing of our Bluetooth Device, Model A1513, FCC ID: BCGA1513 and IC ID: 579C-A1513, fully represents the final version of the equipment as it will be released to the market, in all relevant parts Sincerely, Date: Aug 19, 2015 ____________________ Abhishek Rala Global Certification Manager Apple Inc. 1 Infinite Loop Cupertino, CA 95014. v1.0 Apple Inc. 1 Infinite Loop Cupertino, CA www.apple.com

February 25, 2015 Authorized Individual Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date:

Subject:

To Whom It May Concern:

Pursuant to the provisions of KDB 852134 D01 Authorized Policy Form 731, I, grantee contact, hereby authorize Abhishek Rala to act on behalf of Apple Inc. for all matters relating to equipment authorization, including signing Form 731, attestations, and confidentiality request letters. This authorized individual may also assign another party to act as an authorized agent. This authorization is valid until further written notice from the grantee contact. Marc Douat Apple Inc. 1 Infinite Loop Cupertino, CA 95014

BCGA1513, Model A1513 Request for Permanent Confidentiality Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Subject:

FCC ID:

To whom it may concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), Apple Inc. hereby requests confidential treatment for documents filed with the Commission in connection with the application for equipment authorization referenced above. Permanent Confidentiality Apple Inc. requests that the Commission withholds the following documents from public viewing indefinitely:

Block Diagrams Electrical Schematic Diagrams Technical Descriptions Antenna Specifications These documents reveal detailed technical and design information that is protected by Apple Inc. as confidential and proprietary trade secrets. This information has been disclosed to those required to maintain its confidentiality, and is not customarily disclosed to the public even after commercial release of a device. As a result, disclosure of this information by the Commission would harm Apple Inc. by giving competitors an unfair advantage even after commercial release of the device. It is our understanding that measurement test reports and FCC ID label format cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. v1.1 Apple Inc. 1 Infinite Loop Cupertino, CA www.apple.com Sincerely, ____________________ Abhishek Rala Apple Inc. Global Certification Manager arala@apple.com v1.1 Date: Aug 25, 2015 Apple Inc. 1 Infinite Loop Cupertino, CA www.apple.com

SAR Exclusion Test Report FOR:

Manufacturer: Apple Inc. Model Number: A1513 FCC ID: BCGA1513 Test Report #: SAR_ APPLE_161_15001_FCC_Rev3 Date of Report: August 26, 2015 CETECOM Inc. 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Phone: + 1 (408) 586 6200 Fax: + 1 (408) 586 6299 E-mail: info@cetecom.com http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 Copyright by CETECOM V5.2 2013-02-15 Test Report #: SAR_ APPLE_161_15001_FCC_Rev3 Date of Report: August 26, 2015 FCC ID: BCGA1513 TABLE OF CONTENTS 1. Assessment ................................................................................................................................................................ 3 2. Administrative Data .................................................................................................................................................... 4 2.1. 2.2. 2.3. Identification of the Testing Laboratory Issuing the SAR Test Report ................................................... 4 Identification of the Client ..................................................................................................................... 4 Identification of the Manufacturer ......................................................................................................... 4 3. Equipment under Test (EUT) ..................................................................................................................................... 5 3.1. General Specification of the Equipment under Test .............................................................................. 5 3.2. Antenna Information ............................................................................................................................. 5 3.3. Technical Specification of Supported Radios ........................................................................................ 5 4. Subject of Investigation ............................................................................................................................................. 6 4.1. The FCC Exposure Criteria .................................................................................................................... 6 5. Stand-Alone SAR Evaluation Exclusion ................................................................................................................... 6 6. Report History ............................................................................................................................................................. 6 V1.0 2015-05-03 This report shall not be reproduced except in full without the written approval of:

CETECOM Inc. SAR 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Page 2 of 6 Test Report #: SAR_ APPLE_161_15001_FCC_Rev3 Date of Report: August 26, 2015 FCC ID: BCGA1513 1. Assessment The following device was evaluated against the limits for general population uncontrolled exposure specified in FCC 2.1093 according to SAR evaluation exclusion requirements specified in FCC regulation as listed in KDB 447498 and no deviations were ascertained during the course of the assessment. Manufacturer Apple Inc. Description Bluetooth Device Model #

A1513 Responsible for Testing Laboratory:

August 26, 2015 Compliance

(VP of Radio Communications and EMC) Heiko Strehlow Date Section Name Signature Responsible for the Report:

August 26, 2015 Compliance

(Test Lab Manager) Josie Sabado Date Section Name Signature The test results of this test report relate exclusively to the test item specified in Section 3. CETECOM Inc. USA does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CETECOM Inc. USA. V1.0 2015-05-03 This report shall not be reproduced except in full without the written approval of:

CETECOM Inc. SAR 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Page 3 of 6 Test Report #: SAR_ APPLE_161_15001_FCC_Rev3 Date of Report: August 26, 2015 FCC ID: BCGA1513 Administrative Data 2. 2.1. Identification of the Testing Laboratory Issuing the SAR Test Report Company Name Department Address Telephone Fax Industry Canada Company Number Test Lab Manager Responsible Project Manager 2.2. Identification of the Client Applicants Name Street Address City/Zip Code Country 2.3. Identification of the Manufacturer Same as above client. CETECOM Inc. Compliance 411 Dixon Landing Road Milpitas, CA 95035 U.S.A.

+1 (408) 586 6200

+1 (408) 586 6299 3462B Josie Sabado Josie Sabado Apple Inc. 1 Infinite Loop Cupertino, CA 95014 USA V1.0 2015-05-03 This report shall not be reproduced except in full without the written approval of:

CETECOM Inc. SAR 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Page 4 of 6 Test Report #: SAR_ APPLE_161_15001_FCC_Rev3 Date of Report: August 26, 2015 FCC ID: BCGA1513 3. Equipment under Test (EUT) 3.1. General Specification of the Equipment under Test Model No:

A1513 FCC ID:

BCGA1513 Product Type:

Portable RF Exposure Environment:

General / Uncontrolled Exposure Conditions:

Limb Supported Radios:

Bluetooth v4.2 (LE) 3.2. Antenna Information Antenna Bluetooth Type Internal / External Frequency (MHz) Patch Antenna Internal 2400 2483.5 3.3. Technical Specification of Supported Radios Manufacturer Stated Max Peak Gain

(dBi) 3.5 Type(s) of Modulation GFSK Uplink Transmit Frequency Range

(MHz) 2400 2483.5 Declared Maximum Conducted Output Power

(dBm) 6.5 Signal Type Duty Cycle 63%

Bluetooth 4.2 V1.0 2015-05-03 This report shall not be reproduced except in full without the written approval of:

CETECOM Inc. SAR 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Page 5 of 6 Test Report #: SAR_ APPLE_161_15001_FCC_Rev3 Date of Report: August 26, 2015 FCC ID: BCGA1513 4. Subject of Investigation The objective of the evaluation done by CETECOM Inc. was to assess the applicability of SAR evaluation exclusion according to methods described in applicable standards. 4.1. The FCC Exposure Criteria The FCC SAR test exclusions are set by FCC KDB 447498 section 4.3. 5. Stand-Alone SAR Evaluation Exclusion According to KDB 447498, SAR evaluation can be excluded if the following equation is satisfied:

[(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [f(GHz)] 3.0

[(4.5 mW)/(5 mm)] [2.480] = 1.4 The maximum power of channel is 4.5 mW (6.5 dBm). A minimum test separation distance of 5 mm is used for this calculation because the minimum test separation distance is less than 5 mm. Using the above equation:

SAR testing is excluded because the exclusion threshold of 1.4 is less than 3.0 6. Report History Date July 8, 2015 Report Name Changes to Report SAR_ APPLE_161_15001_FCC 1. First Version July 28, 2015 SAR_ APPLE_161_15001_FCC_Rev1 1. Updated device description 2. Replaces previous test report number August 20, 2015 SAR_ APPLE_161_15001_FCC_Rev2 1. Updated section 3.1, 3.2 2. Replaces previous test report number August 26, 2015 SAR_ APPLE_161_15001_FCC_Rev3 1. Updated section 3.2 2. Replaces previous test report number Report prepared by J. Donnellan J. Sabado J. Sabado J. Sabado V1.0 2015-05-03 This report shall not be reproduced except in full without the written approval of:

CETECOM Inc. SAR 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Page 6 of 6

BCGA1513, Model A1513 Request for Short Term Confidentiality Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Subject:

FCC ID:

To whom it may concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), Apple Inc. hereby requests confidential treatment for documents filed with the Commission in connection with the application for equipment authorization referenced above. Short Term Confidentiality In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, Apple Inc. requests that the Commission withholds the following documents from public viewing for one hundred eighty days after the date the grant of equipment authorization is issued:

External Photographs Internal Photographs Test Setup Photographs User Manual These documents reveal technical and design information that has not been publicly disclosed in marketing materials and is protected by Apple Inc. as confidential and proprietary trade secrets. This information has been disclosed to those required to maintain its confidentiality, and is not customarily disclosed publicly prior to the commercial release of the device. As a result, disclosure of this information by the Commission prior to commercial release would harm Apple Inc. by giving competitors an unfair market advantage. Apple Inc. believes the period of confidentiality requested is necessary to protect the information until the commercial release of a device. v1.1 Apple Inc. 1 Infinite Loop Cupertino, CA www.apple.com It is our understanding that measurement test reports and FCC ID label format cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, ____________________ Abhishek Rala Apple Inc. Global Certification Manager arala@apple.com Date: Aug 25, 2015 v1.1 Apple Inc. 1 Infinite Loop Cupertino, CA www.apple.com

Bluetooth LE FCC / IC Test Report FOR:

Apple Inc. Model Name: A1513 Product Description: Bluetooth Device FCC ID: BCGA1513 IC ID: 579C-A1513 47 CFR Part 15.247 RSS-247 Issue 1 & RSS-Gen Issue 4 TEST REPORT #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 DATE: 2015-08-26 A2LA Accredited IC recognized #

3462B CETECOM Inc. 411 Dixon Landing Road Milpitas, CA 95035 U.S.A. Phone: + 1 (408) 586 6200 Fax: + 1 (408) 586 6299 E-mail: info@cetecomusa.com http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V3.0 2010-10-30 The BLUETOOTH trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to CETECOM Inc. Copyright by CETECOM Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 6.1 6.2 6.3 2.1 2.2 2.3 3.1 3.2 3.3 3.4 3.5 3.6 TABLE OF CONTENTS 1 Assessment ......................................................................................................................................... 4 2 Administrative Data .......................................................................................................................... 5 Identification of the Testing Laboratory Issuing the Test Report............................................................. 5 Identification of the Client ........................................................................................................................ 5 Identification of the Manufacturer ............................................................................................................ 5 3 Equipment under Test (EUT) .......................................................................................................... 6 Specification of the Equipment under Test .............................................................................................. 6 Identification of the Equipment under Test (EUT)................................................................................... 7 Identification of Accessory equipment ..................................................................................................... 7 Environmental conditions during Test: .................................................................................................... 7 Dates of Testing: ....................................................................................................................................... 7 Test mode of operation: ............................................................................................................................ 7 Subject Of Investigation ................................................................................................................... 8 4 5 Summary of Measurement Results .................................................................................................. 9 6 Measurements .................................................................................................................................. 10 Radiated Measurement Procedure ..................................................................................................... 10 6.1.1 Sample Calculations for Radiated Measurements ........................................................................... 11 Conducted Emissions Measurement Procedure (AC Power Line) .................................................. 11 RF Conducted Measurement Procedure ............................................................................................ 12 7 Maximum Conducted Output Power and EIRP .......................................................................... 13 Limits: ..................................................................................................................................................... 13 Test Conditions: ...................................................................................................................................... 13 Test Procedure ........................................................................................................................................ 13 Test Data ................................................................................................................................................. 14 Measurement Result ............................................................................................................................... 15 Measurement Plots:................................................................................................................................. 15 Power Spectral Density ................................................................................................................... 16 Limits: ..................................................................................................................................................... 16 Test Conditions: ...................................................................................................................................... 16 Measurement procedure .......................................................................................................................... 16 Test Data Results: ................................................................................................................................... 17 8.4.1 Measurement Result ........................................................................................................................... 17 Measurement Plots:................................................................................................................................. 18 9 Band Edge Compliance Unrestricted Band Edges .................................................................... 19 Limits: FCC15.247 (d) / RSS-247 Section 5.5 .................................................................................... 19 Test Conditions: ...................................................................................................................................... 19 Measurement Procedure: ........................................................................................................................ 19 Measurement Result ............................................................................................................................... 20 9.4.1 Measurement Plots: ............................................................................................................................ 20 10 Band Edge Compliance Restricted Band Edges ........................................................................ 21 10.1 Limits: 15.247/15.209/15.205 & RSS-Gen 8.9/ 8.10 ........................................................................... 21 10.2 Test Conditions: ...................................................................................................................................... 22 10.3 Measurement Procedure: ........................................................................................................................ 22 10.4 Measurement Result ............................................................................................................................... 22 10.4.1 Measurement Plots: ....................................................................................................................... 23 11 Occupied Bandwidth (6dB and 99% Bandwidth) ....................................................................... 27 7.1 7.2 7.3 7.4 7.5 7.6 9.1 9.2 9.3 9.4 8.1 8.2 8.3 8.4 8.5 8 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 11.1 11.2 11.3 11.4 Limits: ..................................................................................................................................................... 27 Test Conditions: ...................................................................................................................................... 27 Test Procedure ........................................................................................................................................ 27 Test Data Results: ................................................................................................................................... 28 2.4 GHz Band ................................................................................................................................................... 28 11.5 Measurement Result ............................................................................................................................... 28 11.6 Measurement Plots:................................................................................................................................. 28 12 Radiated Transmitter Spurious Emissions - Restricted Bands .................................................. 31 Limits: ..................................................................................................................................................... 31 12.1 12.2 Test Conditions: ...................................................................................................................................... 32 12.3 Measurement procedure:......................................................................................................................... 32 12.3.1 Measurement Result ....................................................................................................................... 32 12.3.2 Measurement Plots: ....................................................................................................................... 33 13 AC Power Line Conducted Emissions .......................................................................................... 41 13.1 References:.............................................................................................................................................. 41 Limits: ..................................................................................................................................................... 41 13.2 13.3 Test Conditions: ...................................................................................................................................... 41 13.4 Measurement procedure:......................................................................................................................... 41 13.5 Results ..................................................................................................................................................... 41 Test Data/ Plots .............................................................................................................................. 42 14 Test Equipment and Ancillaries used for tests ............................................................................. 44 15 Block Diagrams ............................................................................................................................... 45 16 Revision History .............................................................................................................................. 47 13.5.1 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 1 Assessment The following device was evaluated against the applicable criteria specified in FCC rules Parts 15.247 of Title 47 of the Code of Federal Regulations and IC standard RSS-247 Issue 1, Section 5 and no deviations were ascertained during the course of the tests performed. Description Bluetooth Device Model #

A1513 Company Apple Inc. Responsible for Testing Laboratory:

2015-08-26 Compliance

(Test Lab Manager)

(Compliance Manager) Josie Sabado Signing on behalf of Franz Engert Date Section Name Signature Responsible for the Report:

2015-08-26 Compliance

(EMC Engineer) Douglas Antioco Date Section Name Signature The test results of this test report relate exclusively to the test item specified in Section3. CETECOM Inc. USA does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CETECOM Inc. USA. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 2 Administrative Data 2.1 Identification of the Testing Laboratory Issuing the Test Report Company Name:

Department:

Address:

Telephone:

Fax:

Compliance Manager:

CETECOM Inc. Compliance 411 Dixon Landing Road Milpitas, CA 95035 U.S.A.

+1 (408) 586 6200

+1 (408) 586 6299 Franz Engert Responsible Project Leader:

Douglas Antioco 2.2 Identification of the Client Applicants Name:

Apple Inc. Street Address:

City/Zip Code Country Contact Person:

Phone No. Fax:

e-mail:

1 Infinite Loop Cupertino, CA 95014 USA Richard Lee

(415)728-7644

-----------

richard.lee@apple.com 2.3 Identification of the Manufacturer Manufacturers Name:

Same as Applicant Manufacturers Address:

City/Zip Code Country

---

---

---

Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 3 Equipment under Test (EUT) 3.1 Specification of the Equipment under Test Model No:

A1513 HW / SW Revision :

Rev 1.0/v0095 FCC-ID:

IC-ID:

HVIN PMN BCGA1513 579C-A1513 A1513 A1513 Product Description:

Bluetooth Device Technology / Type(s) of Modulation:

Operating Frequency Ranges (MHz) /

Channels:

Antenna info:

Max. Output Power:

Rated Operating Voltage Range / Power Supply:

Rated Operating Temperature Range:

Bluetooth v4.2, LE, using FHSS with GFSK Nominal band: 2400 2483.5;

Center to center: 2402(ch 0) 2480(ch 39), 40 channels Internal, Patch Antenna Documented max antenna gain(2.4GHz) = 3.5 dBi Conducted (Measured):

6.55 dBm (4.52 mW) Radiated EIRP (Calculated with documented max antenna gain):

10.05 dBm (10.12 mW) Battery Vmin: 3.0V dc/ Vnom: 3.7V dc / Vmax: 4.3V dc 0C to 35C Other Radios included in the device:

None EUT status Hardware Version Rev 1.0 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 3.2 Identification of the Equipment under Test (EUT) EUT #

Serial Number HW Version SW Version Notes/Comments 1 2 3 C08M401BFY8F Rev 1.0 C08NW06AGH16 Rev 1.0 v0095 v0095 Radiated Sample Conducted Emissions

(AC Power line) Sample C08NN004GDDY Rev 1.0 v0095 Conducted RF Sample 3.3 Identification of Accessory equipment AE #

Type Manufacturer 1 2 USB Power Adapter Apple Dummy Battery Apple 3.4 Environmental conditions during Test:

Model A1357 N/A Serial Number 0010ADU00 N/A The following environmental conditions were maintained during the course of testing:

Ambient Temperature: 20-25oC Relative humidity: 40-60%

3.5 Dates of Testing:

4/11/2014, 1/29/2015 3.6 Test mode of operation:

Mode Data rate (Mbps) Modulation scheme Bluetooth LE 1.0 GFSK Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 4 Subject Of Investigation The objective of the measurements done by Cetecom Inc. was to establish compliance with the requirements listed in FCC rules Part 15.247 of Title 47 of the Code of Federal Regulations and Radio Standard Specification RSS-247 Issue 1, Section 5 of Industry Canada. This test report is to support a request for new equipment authorization under the FCC ID: BCGA1513. All testing was applied to the product referred to in Section 3 as the EUT. The EUT was tested on the lowest, middle and highest channel of its specified operating range. For radiated measurements, all data in this report shows the worst case between horizontal and vertical antenna polarizations and for all orientations of the EUT. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 5 Summary of Measurement Results Test Specification Test Case Temperature and Voltage Conditions Mode Pass Fail NA NP Result 15.247(e) RSS-247 5.2(1) 15.247(a)(1) RSS-247 5.2(2) 15.247(b)(1) RSS-247 5.4(4) 15.247(d) RSS-247 5.5 15.247/15.209/15.205 Power Spectral Density Emission Bandwidth Maximum Conducted Output Power and EIRP Band edge compliance-

Unrestricted Band Edges Band edge compliance-

RSS-Gen 8.9/ 8.10 Restricted Band 15.247(d) 15.209 15.247(d) 15.209 RSS-Gen 6.13 15.207(a) RSS Gen 8.8 Edges TX Spurious emissions-

Conducted TX Spurious emissions-

Radiated AC Conducted Emissions Nominal Bluetooth LE Nominal Bluetooth LE Nominal Bluetooth LE Complies Complies Complies Nominal Bluetooth LE Complies Nominal Bluetooth LE Complies Nominal Bluetooth LE See Note 1 Nominal Bluetooth LE Nominal Bluetooth LE Complies Complies Note: NA= Not Applicable; NP= Not Performed. 1. Conducted unwanted emissions test against non-restricted band limits is NOT PERFORMED except at the authorized band edge (see band edge compliance test) since radiated spurious emissions is tested against more stringent restricted band limits over the complete measurement range (9kHz to 26GHz) has passed. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 6 Measurements 6.1 Radiated Measurement Procedure The radiated measurement is performed according to:

ANSI C63.10 (2013) The exploratory measurement is accomplished by running a matrix of 16 sweeps over the required frequency range with R&S Test-SW EMC32 for 4 positions of the turntable, two orthogonal positions of the EUT and both antenna polarizations. This procedure exceeds the requirement of the above standards to cover the 3 orthogonal axis of the EUT. A max peak detector is utilized during the exploratory measurement. The Test-SW creates an overall maximum trace for all 12 sweeps and saves the settings for each point of this trace. The maximum trace is part of the test report. The 10 highest emissions are selected with an automatic algorithm of EMC32 searching for peaks in the noise floor and ensuring that broadband signals are not selected multiple times. The maxima are then put through the final measurement and again maximized in a 90deg range of the turntable, fine search in frequency domain and height scan between 1m and 4m. The above procedure is repeated for all possible ways of power supply to EUT and for all supported modulations. In case there are no emissions above noise floor level only the maximum trace is reported as described above. The results are split up into up to 4 frequency ranges due to antenna bandwidth restrictions. A magnetic loop is used from 9kHz to 30MHz, a Biconlog antenna is used from 30MHz to 1GHz, two different horn antennas are used to cover frequencies up to 40GHz. Radiated Measurement Uncertainty:

Uncertainty in dB Radiated <30MHz Uncertainty in dB Radiated 30MHz -

1GHz Uncertainty in dB Radiated > 1GHz 2.48 4.86 1.94 3.79 2.16 4.24

+/-2.5 dB

+/-2.0 dB

+/- 2.3dB Standard Deviation k=1 95% Confidence Interval in dB 95% Confidence Interval in dB in Delta to Result Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 6.1.1 Measurements from the Spectrum Analyzer/ Receiver are used to calculate the Field Strength, taking into account the following parameters:

Sample Calculations for Radiated Measurements 1. Measured reading in dBV 2. Cable Loss between the receiving antenna and SA in dB and 3. Antenna Factor in dB/m FS (dBV/m) = Measured Value on SA (dBV)+ Cable Loss (dB)+ Antenna Factor (dB/m) Eg:

Frequency Measured SA Cable Loss

(MHz)

(dBV) 1000 80.5

(dB) 3.5 Antenna Factor Field Strength Correction

(dB) 14 Result

(dBV/m) 98.0 All radiated measurement plots in this report are taken from a test SW that calculates the Field Strength based on the above equation. 6.2 Conducted Emissions Measurement Procedure (AC Power Line) Conducted Emissions measurements done according to:

ANSI C63.10 (2013) Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 6.3 RF Conducted Measurement Procedure Measurement according to FCC KDB 558074 D01 v03r03 (DTS Meas Guidance) Test Setup for Conducted Measurements DUT Attenuator Spectrum Analyzer 1. Connect the equipment as shown in the above diagram. 2. Adjust the settings by entering test commands for TX/RX mode on/off, changing channels, modulations and data rates. 3. Measurements are to be performed with the EUT set to the low, middle and high channels. Measurement Uncertainty:

Uncertainty in dB Conducted measurement standard deviation k=1 95% confidence interval in dB 0.63 1.24 95% confidence interval in dB in delta to Result

+-0.7dB Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 7 Maximum Conducted Output Power and EIRP 7.1 Limits:

Maximum Output Power:

FCC 15.247 (b)(3): 1W IC RSS-247 issue 1, Section 5.4(4): 1W EIRP:

IC RSS-247 issue 1, annex 8.4(2): 4W 7.2 Test Conditions:

Tnom: 21oC; Vnom: 3.7V 7.3 Test Procedure Measurement according to FCC KDB 558074 D01 v03r03 section 9.2.2.4 Maximum conducted (average) output power Method AVGSA-2 (trace averaging across on and off times of the EUT transmissions, followed by duty cycle correction) Span 1.5 times the OBW. RBW = 1-5% of the OBW, not to exceed 1 MHz. VBW 3 x RBW Sweep points 2 span / RBW. (This gives bin-to-bin spacing RBW/2, so that narrowband signals are not lost between frequency bins.) Sweep time = auto. Detector = RMS (i.e., power averaging), if available. Otherwise, use sample detector mode. Trace = average at least 100 traces in power averaging (i.e., RMS) mode; however, the number of traces to be averaged shall be increased above 100 as needed such that the average accurately represents the true average over the on and off periods of the transmitter.

- Do not use sweep triggering. Allow the sweep to free run.

- Compute power by integrating the spectrum across the OBW of the signal using the instruments band power measurement function with band limits set equal to the OBW band edges..

- Add 10 log (1/x), where x is the duty cycle, to the measured power in order to compute the average power during the actual transmission times (because the measurement represents an average over both the on and off times of the transmission). For example, add 10 log (1/0.25) = 6 dB if the duty cycle is 25 %. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 7.4 Test Data Maximum Conducted Output Power (dBm) Frequency (MHz) Limit = 30 dBm Mode Bluetooth LE Duty Cycle CF 2.11 2412 Channel 1 2437 Channel 6 2462 Channel 11 Measured Corrected Measured Corrected Measured Corrected 4.44 6.55 4.23 6.34 4.13 6.24 Calculated Radiated Output Power EIRP (dBm) Limit = 36 dBm Frequency (MHz) Antenna Gain

(dBi) 3.5 Mode Bluetooth LE 2412 Channel 1 2437 Channel 6 2462 Channel 11 10.05 9.84 9.74 Declared Antenna Gain in the 2.4GHz band: 3.5 dBi DC = Txon / Txon + Txoff = 0.3836 ms / 0.6240 ms = 0.615 or 61.5%

DCCF = 10 log (1/x); x = duty cycle DCCF = 10 log (1/0.615) = 2.11 Ref 41 dBmAtt 20 dB**Offset 16.1 dB A SGLTRGLVL3DBRBW 1 MHzVBW 10 MHzSWT 2 msCenter 2.402 GHz200 s/CLRWR *1 RM-50-40-30-20-100102030401Marker 1 [T1 ] 6.48 dBm 628.205128 s 2Delta 2 [T1 ] 0.02 dB 623.979487 s 1Delta 1 [T1 ] -0.18 dB 383.594872 s POWER [T1]RMS 4.14 dBmDate: 29.JAN.2015 17:28:16 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 7.5 Measurement Result Pass. 7.6 Measurement Plots:

Ch.0 / 2402 MHz Maximum Peak Conducted Power Modulation/Packet Type: GFSK Data Rate: 1 Mbps Ch.19 / 2440 MHz Modulation/Packet Type: GFSK Data Rate: 1 Mbps Ch.39 / 2480 MHz Modulation/Packet Type: GFSK Data Rate: 1 Mbps Att 10 dB*** B 3DBRBW 20 kHzVBW 100 kHzSWT 45 msRef 31.1 dBmOffset 16.1 dBLVLCenter2.402 GHzSpan3 MHz300 kHz/ *1 RMAVG-60-50-40-30-20-100102030 Tx Channel Bandwidth 1.0374 MHz Power 4.44 dBm SWP 100 of 1001Marker 1 [T1 ] -7.29 dBm 2.401981100 GHzDate: 29.JAN.2015 17:01:55Att 10 dB* B Ref 31.1 dBmOffset 16.1 dBLVL *1 RMAVGCenter2.44 GHzSpan3 MHz300 kHz/**3DBRBW 20 kHzVBW 100 kHzSWT 45 ms-60-50-40-30-20-100102030 Tx Channel Bandwidth 1.0398 MHz Power 4.23 dBm SWP 100 of 1001Marker 1 [T1 ] -7.27 dBm 2.440002700 GHzDate: 29.JAN.2015 17:07:50Att 10 dB* B Ref 31.1 dBmOffset 16.1 dBLVLCenter2.48 GHzSpan3 MHz300 kHz/**3DBRBW 20 kHzVBW 100 kHzSWT 45 ms *1 RMAVG-60-50-40-30-20-100102030 Tx Channel Bandwidth 1.0398 MHz Power 4.13 dBm SWP 100 of 1001Marker 1 [T1 ] -6.77 dBm 2.479986800 GHzDate: 29.JAN.2015 17:06:38 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 8 Power Spectral Density 8.1 Limits:

15.247 (e) & RSS-247 Section 5.2 (2) For digitally modulated systems, the peak power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 8.2 Test Conditions:

Tnom: 21oC; Vnom: 3.7V 8.3 Measurement procedure Measurement according to FCC KDB 558074 D01 V03R03 section 10.5 Maximum power spectral density Method AVGPSD-2 (trace averaging across on and off times of the EUT transmissions, followed by duty cycle correction) Center Frequency = DTS channel center frequency. Span 1.5 times the OBW. RBW = 3 kHz RBW 100 kHz. VBW 3 x RBW Detector = power averaging (RMS) or sample detector (when RMS not available) Sweep time = auto couple Trace = averaging (RMS) mode over a minimum of 100 traces

- Ensure that the number of measurement points in the sweep 2 x span/RBW.

- Do not use sweep triggering. Allow sweep to free run.

- Use the peak marker function to determine the maximum amplitude level.

- Add 10 log (1/x), where x is the duty cycle measured in step (a, to the measured PSD to compute the average PSD during the actual transmission time.

- If resultant value exceeds the limit, then reduce RBW (no less than 3 kHz) and repeat (note that this may require zooming in on the emission of interest and reducing the span in order to meet the minimum measurement point requirement as the RBW is reduced). Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 8.4 Test Data Results:

Limit = 8 dBm in any 3 KHz band Mode Bluetooth LE Duty Cycle CF 2.11 Maximum Power Spectral Density (dBm) Frequency (MHz) 2412 Channel 1 2437 Channel 6 2462 Channel 11 Measured Corrected Measured Corrected Measured Corrected

-7.29

-5.18

-7.27

-5.16

-6.77

-4.66 8.4.1 Measurement Result Pass. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 8.5 Measurement Plots:

Maximum Power Spectral Density Ch.0 / 2402 MHz Modulation: GFSK Data Rate: 1 Mbps Ch.19 / 2440 MHz Modulation: GFSK Data Rate: 1 Mbps Ch.39 / 2480 MHz Modulation: GFSK Data Rate: 1 Mbps Att 10 dB* B Ref 31.1 dBmOffset 16.1 dBLVLCenter2.48 GHzSpan3 MHz300 kHz/**3DBRBW 20 kHzVBW 100 kHzSWT 45 ms *1 RMAVG-60-50-40-30-20-100102030 Tx Channel Bandwidth 1.0398 MHz Power 4.13 dBm SWP 100 of 1001Marker 1 [T1 ] -6.77 dBm 2.479986800 GHzDate: 29.JAN.2015 17:06:38Att 10 dB* B Ref 31.1 dBmOffset 16.1 dBLVL *1 RMAVGCenter2.44 GHzSpan3 MHz300 kHz/**3DBRBW 20 kHzVBW 100 kHzSWT 45 ms-60-50-40-30-20-100102030 Tx Channel Bandwidth 1.0398 MHz Power 4.23 dBm SWP 100 of 1001Marker 1 [T1 ] -7.27 dBm 2.440002700 GHzDate: 29.JAN.2015 17:07:50Att 10 dB*** B 3DBRBW 20 kHzVBW 100 kHzSWT 45 msRef 31.1 dBmOffset 16.1 dBLVLCenter2.402 GHzSpan3 MHz300 kHz/ *1 RMAVG-60-50-40-30-20-100102030 Tx Channel Bandwidth 1.0374 MHz Power 4.44 dBm SWP 100 of 1001Marker 1 [T1 ] -7.29 dBm 2.401981100 GHzDate: 29.JAN.2015 17:01:55 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 9 Band Edge Compliance Unrestricted Band Edges 9.1 Limits: FCC15.247 (d) / RSS-247 Section 5.5 FCC15.247 (d) / RSS-247 Section 5.5 In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in 15.209(a) or RSS-Gen is not required. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a). 9.2 Test Conditions:

Tnom: 21oC; Vnom: 3.7V 9.3 Measurement Procedure:

Conducted Measurement according to FCC KDB 558074 D01 v03r03 section 11 Establish a reference level by using the following procedure:

a)Set instrument center frequency to DTS channel center frequency. b)Set the span to 1.5 times the DTS bandwidth. c)Set the RBW = 100 kHz. d)Set the VBW 3 x RBW. e)Detector = peak. f)Sweep time = auto couple. g)Trace mode = max hold. h)Allow trace to fully stabilize. i)Use the peak marker function to determine the maximum PSD level. Note that the channel found to contain the maximum PSD level can be used to establish the reference level. Emission level measurement a)Set the center frequency and span to encompass frequency range to be measured. b)Set the RBW = 100 kHz. c)Set the VBW 3 x RBW. d)Detector = peak. e)Sweep time = auto couple. f)Trace mode = max hold. g)Allow trace to fully stabilize. h)Use the peak marker function to determine the maximum amplitude level. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 9.4 Measurement Result Pass. 9.4.1 Measurement Plots:

Lower Unrestricted Band Edge Ch. Low / 2402MHz / Peak Band Edge Frequency: 2.4 GHz GFSK The peak power in 100 KHz bandwidth outside the authorized frequency band is attenuated by more than 30 dB relative to the in-band peak power spectral density level in 100 KHz, as shown by the delta marker in this plot. Att 10 dB* B *3DBRBW 100 kHzSWT 45 msOffset 19.6 dBLVLRef 18 dBmCenter2.4 GHzSpan10 MHz1 MHz/*VBW 300 kHz1 PKMAXH-80-70-60-50-40-30-20-100101Marker 1 [T1 ] 9.95 dBm 2.402009000 GHz1Delta 1 [T1 ] -51.38 dB -3.208000000 MHzDate: 29.JAN.2015 18:11:19 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 10 Band Edge Compliance Restricted Band Edges 10.1 Limits: 15.247/15.209/15.205 & RSS-Gen 8.9/ 8.10 Only spurious emissions are permitted in any of the frequency bands listed below:

(b) Except as provided in paragraphs (d) and (e) of this section, the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in 15.35 apply to these measurements.

*PEAK LIMIT= 74dBV/m

*AVG. LIMIT= 54dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 10.2 Test Conditions:

Tnom: 21oC; Vnom: 3.7V 10.3 Measurement Procedure:

Radiated Measurements were performed according to FCC KDB 558074 D01 V03R03 section 12.1 10.4 Measurement Result Pass. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 10.4.1 Measurement Plots:

Lower Band Edge Ch. Low / 2402MHz / Peak Restricted Bandedge Frequency: 2.39 GHz GFSK 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 12023102320 2340 2360 2380 2400 2420Level in dBV/mFrequency in MHzMaxPeak-ClearWrite-PK+MaxPeak-MaxHold-PK+FCC 15.247 PkFCC 15.247 Pk2.383333333 GHz60.135 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Lower Band Edge Ch. Low / 2402MHz /

Average Restricted Band Edge Frequency: 2.39 GHz GFSK 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 12023102320 2340 2360 2380 2400 2420Level in dBV/mFrequency in MHzMaxPeak-MaxHold-PK+Average-MaxHold-AVGFCC 15.247 AvgFCC 15.247 Avg2.385977564 GHz47.892 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Measurement Plots Ch. High / 2480MHz / Peak Frequency Range: 2.4835 2.5 GHz GFSK Upper Restricted Band 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 1202460 2470 2480 2490 2500 2510Level in dBV/mFrequency in MHzMaxPeak-ClearWrite-PK+MaxPeak-MaxHold-PK+FCC 15.247 PkFCC 15.247 Pk2.484759615 GHz61.135 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Ch. High / 2480MHz / Avg Frequency Range: 2.4835 2.5 GHz GFSK Upper Restricted Band 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 1202460 2470 2480 2490 2500 2510Level in dBV/mFrequency in MHzMaxPeak-MaxHold-PK+FCC 15.247 AvgFCC 15.247 Avg2.483557692 GHz49.735 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 11 Occupied Bandwidth (6dB and 99% Bandwidth) 11.1 Limits:

15.247 (a)(2) Systems using digital modulation techniques may operate in the 24002483.5 MHz band. The minimum 6 dB bandwidth shall be at least 500 kHz. RSS-247 Section 5.2 (1) The minimum 6 dB bandwidth shall be 500 kHz. 11.2 Test Conditions:

Tnom: 22 oC; Vnom: 3.7V 11.3 Test Procedure Measurement according to FCC KDB 558074 D01 v03r03 section 8.1 For 6 dB bandwidth:

Spectrum Analyzer settings:

Span= Wide enough to capture the entire emission bandwidth RBW= 100 KHz VBW 3xRBW Detector: Peak-

Sweep Time: Auto Trace = Max Hold Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the peak level measured in the fundamental emission. For 99% bandwidth:

Use the occupied bandwidth in the measurement function of the spectrum analyzer with power bandwidth setting at 99%

Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 11.4 Test Data Results:

2.4 GHz Band Occupied Bandwidth (MHz) Frequency (MHz) Mode 2404 Channel 0 2440 Channel 19 2480 Channel 39 6dB

(KHz) 99%

(MHz) 6dB

(KHz) 99%

(MHz) 6dB

(KHz) 99%

(MHz) Bluetooth LE 681.69 1.0374 682.26 1.0395 692.5 1.0398 11.5 Measurement Result Pass. 11.6 Measurement Plots:

Ch.0 / 2402 MHz Modulation: GFSK Data Rate: 1 Mbps 6 dB and 99% Bandwidth Offset 1.1 dB A LVLMAXHAtt 20 dB*Ref 26 dBm1 PK300 kHz/Center2.402 GHzSpan3 MHz**3DBRBW 100 kHzVBW 10 MHzSWT 45 ms-70-60-50-40-30-20-10010201Marker 1 [T1 ] 6.66 dBm 2.402009900 GHz2Delta 2 [T1 ] -6.04 dB -346.115384610 kHz1Delta 1 [T1 ] -6.27 dB 335.569230775 kHzOBW 1.037400000 MHzT1Temp 1 [T1 OBW] -7.22 dBm 2.401490600 GHzT2Temp 2 [T1 OBW] -7.24 dBm 2.402528000 GHzDate: 29.JAN.2015 15:46:56 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Ch.19 / 2440 MHz Modulation: GFSK Data Rate: 1 Mbps 6 dB and 99% Bandwidth Offset 1.1 dB A LVLMAXHAtt 20 dB*Ref 26 dBm1 PK300 kHz/Center2.44 GHzSpan3 MHz**3DBRBW 100 kHzVBW 10 MHzSWT 45 ms-70-60-50-40-30-20-10010201Marker 1 [T1 ] 6.36 dBm 2.440007200 GHz2Delta 2 [T1 ] -6.65 dB -350.961538460 kHz1Delta 1 [T1 ] -6.07 dB 331.299999999 kHzOBW 1.039500000 MHzT1Temp 1 [T1 OBW] -7.53 dBm 2.439490600 GHzT2Temp 2 [T1 OBW] -7.53 dBm 2.440530100 GHzDate: 29.JAN.2015 15:45:12 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Ch.39 / 2480 MHz Modulation: GFSK Data Rate: 1 Mbps 6 dB and 99% Bandwidth Offset 1.1 dB A LVLMAXHAtt 20 dB*Ref 26 dBm1 PK300 kHz/Center2.48 GHzSpan3 MHz**3DBRBW 100 kHzVBW 10 MHzSWT 45 ms-70-60-50-40-30-20-10010201Marker 1 [T1 ] 6.47 dBm 2.480009300 GHz2Delta 2 [T1 ] -6.27 dB 322.115384616 kHz1Delta 1 [T1 ] -6.24 dB -360.576923076 kHzOBW 1.039800000 MHzT1Temp 1 [T1 OBW] -7.29 dBm 2.479476500 GHzT2Temp 2 [T1 OBW] -7.74 dBm 2.480516300 GHzDate: 29.JAN.2015 15:50:11 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 12 Radiated Transmitter Spurious Emissions - Restricted Bands 12.1 Limits:

15.247/15.205/15.209 & RSS-Gen 8.9/ 8.10 (restricted bands)

(a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below:

Radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see 15.205(c)).

*PEAK LIMIT= 74dBV/m

*AVG. LIMIT= 54dBV/m Table 1: Field strength limits table above 30 MHz Frequency of emission (MHz) Field strength (V/m) 100 (40dBV/m) 150 (43.5 dBV/m) 200 (46 dBV/m) 500 (54 dBV/m) 3088 88216 216960 Above 960 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Table 2: Field strength limits table below 30 MHz Frequency of emission (MHz) Field strength (V/m) Measurement Distance (m) 0.0090.490 0.4901.705 1.70530.0 2400/F(kHz) 24000/F(kHz) 30 300 30 30 Radiated spurious emissions shall be measured for the transmit frequencies, transmit power, and data rate for the lowest, middle and highest channel in each frequency band of operation and for the highest gain antenna for each antenna type, and using the appropriate parameters and test requirements described in 5.4. The highest (or worst-case) data rate shall be recorded for each measurement. 12.2 Test Conditions:

Tnom: 23 oC; Vnom: 3.7V Test mode: Modulation: GFSK 12.3 Measurement procedure:

Measurement according to ANSI C63.10:2013 (also refer to section 6.1 in this test report) Analyzer Settings:

From 9 KHz 30 MHz RBW = 9 KHz Detector: Peak From 30 MHz 1 GHz Detector = Peak / Quasi-Peak RBW=120 KHz (<1GHz) Above 1 GHz Detector = Peak / Average RBW= 1MHz Test mode: Modulation: GFSK- the highest conducted output power. Plots in this report represent the worst case emissions for horizontal and vertical antenna polarizations and for three orientations of the EUT. 12.3.1 Measurement Result Pass. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 12.3.2 Measurement Plots:

Plots reported here represent the worst case emissions for horizontal and vertical antenna polarizations and for three orientations of the EUT. TX Radiated Spurious Emissions: 9kHz 30MHz Ch. Mid Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps 20 30 40 50 60 70 80 90 100 110 120 130 1409k203050100k2003005001M2M3M5M10M2030MLevel in dBV/mFrequency in HzFCC 15 9kHz converted to 3mPreview Result 1-PK+Final Result 1-PK+FCC 15 9kHz converted to 3m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 30 MHz 1GHz Ch. Low Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps 0 5 10 15 20 25 30 35 40 45 50 55 60 65 7030M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzFCC 15Preview Result 1-PK+Data Reduction Result 1 [3]-PK+FCC 15735.454545 MHz29.910 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 30 MHz 1GHz Ch. Mid Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps 0 5 10 15 20 25 30 35 40 45 50 55 60 65 7030M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzFCC 15Preview Result 1-PK+Data Reduction Result 1 [3]-PK+FCC 15905.519481 MHz31.543 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 30 MHz 1GHz Ch. High Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps 0 5 10 15 20 25 30 35 40 45 50 55 60 65 7030M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzFCC 15Preview Result 1-PK+Data Reduction Result 1 [3]-PK+FCC 15899.220779 MHz31.817 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 1 GHz 18 GHz Ch. Low Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps Note: Emission above limit is Tx Signal 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 1101G2G3G4G5G6 8 10G18GLevel in dBV/mFrequency in Hz74 dBuV per m54 dBuV per mPreview Result 1-PK+Preview Result 2-AVG74 dBuV per m54 dBuV per m2.403846154 GHz100.627 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 1 GHz 18 GHz Ch. Mid Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps Note: Emission above limit is Tx Signal 30 35 40 45 50 55 60 65 70 75 80 85 90 95 1001G2G3G4G5G6 8 10G18GLevel in dBV/mFrequency in Hz74 dBuV per m54 dBuV per mPreview Result 1-PK+Preview Result 2-AVG74 dBuV per m54 dBuV per m2.442307692 GHz94.567 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 1 GHz 18 GHz Ch. High Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps Note: Emission above limit is Tx Signal 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 1101G2G3G4G5G6 8 10G18GLevel in dBV/mFrequency in Hz74 dBuV per m54 dBuV per mPreview Result 1-PK+Preview Result 2-AVG74 dBuV per m54 dBuV per m2.480769231 GHz98.767 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 TX Radiated Spurious Emission: 18 GHz 26 GHz Ch. High Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 8018 19 20 21 22 23 24 25 26Level in dBV/mFrequency in GHz74 dBuV per m54 dBuV per mPreview Result 1-PK+Preview Result 2-AVG74 dBuV per m54 dBuV per m18.512820513 GHz53.252 dBV/m22.000000000 GHz43.099 dBV/m25.371794872 GHz44.558 dBV/m Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 13 AC Power Line Conducted Emissions 13.1 References:

FCC: CFR Part 15.207/ RSS-Gen 8.8 The purpose of this test is to measure unwanted radio frequency currents induced in any AC conductor external to the equipment which could conduct interference to other equipment via the AC electrical network. 13.2 Limits:

15.207 & RSS-Gen 8.8

(a) Except as shown in paragraphs (b) and (c) of this section of the CFR, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table (1), as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Table 1:

Frequency of emission (MHz) Quasi-peak Average Conducted limit (dBV) 0.150.5 0.55 530 66 to 56*

56 to 46*

56 60 46 50

*Decreases with the logarithm of the frequency. 13.3 Test Conditions:

Tnom: 23 oC; Vnom: 3.7V Receive and transmit mode of operation of operation 13.4 Measurement procedure:

Measurement according to ANSI C63.10:2013 section 6.2 and 4.1 (also refer to section 6, 6.3 in this test report) Analyzer Settings:

CISPR Bandwidth- 9KHz. Detector = Quasi-peak / Average Measurement Uncertainty: 3.0dB 13.5 Results Pass. Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 13.5.1 Test Data/ Plots Plots shown here represent the combined worse case emissions for phase and neutral lines. Conducted Emissions: 150 KHz 30 MHz TX Mode (GFSK):

Conducted Emissions: 150 kHz 30 MHz Ch. Mid Mode: Bluetooth LE Modulation: GFSK Data Rate: 1 Mbps

-10 -5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in HzEN 55022 Voltage on Mains QPEN 55022 Voltage on Mains AVPreview Result 1-PK+Preview Result 2-AVGEN 55022 Voltage on Mains QPEN 55022 Voltage on Mains AV Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Conducted Emissions: 150 kHz 30 MHz RX/Idle mode

-10 -5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in HzEN 55022 Voltage on Mains QPEN 55022 Voltage on Mains AVPreview Result 1-PK+Preview Result 2-AVGEN 55022 Voltage on Mains QPEN 55022 Voltage on Mains AV Cal Interval 2 Years 2 Years N/A 3 Years 3 Years 3 years n/a Sept 2013 Jun 2013 N/A Apr 2012 Mar 2012 Apr 2012 n/a Part of system calibration Part of system calibration Part of system calibration Part of system calibration Jun 2013 Jun 2013 3 Years 2 Years Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 14 Test Equipment and Ancillaries used for tests Instrument/Ancillary Model Manufacturer Serial No. Cal Date EMI Receiver/Analyzer Spectrum Analyzer Pre-Amplifier Binconilog Antenna Horn Antenna Loop Antenna Communication Antenna High Pass Filter High Pass Filter 6GHz High Pass Filter Pre-Amplifier LISN Spectrum Analyzer ESU 40 FSU Miteq EMCO EMCO EMCO IBP5-900/1940 5HC2700 4HC1600 HPM50106 JS4-00102600 R&S Rohde&Schwarz Rohde & Schwarz Rohde & Schwarz JS40010260 3141 3115 6512 Kathrein Trilithic Inc. Trilithic Inc. Microtronics Miteq ESH3-Z5 FSU 100251 200302 340125 0005-1186 35114 00049838 n/a 9926013 9922307 001 00616 836679/003 200302 Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 15 Block Diagrams Radiated Emissions Test Setup for Below 30MHz Measurements 3 m Distance EUT at 80cm Turn-Table Radiated Emissions Test Setup from 30M-1GHz Measurements 3 m Distance EMI Receiver Height Scan 1-4m EUT at 80 cm Turn-Table BiLog Measurement Antenna Chamber Ground plane EMI Receiver Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 Radiated Emissions Test Setup >1GHz Measurements Height Scan 1-4m 3 m Distance Horn Measurement Antenna Chamber Ground plane EMI Receiver EUT at 150cm Turn-Table Test Report #: EMC_ APPLE-144-14002_15.247_BTLE_rev2 FCC ID: BCGA1513 Date of Report : 2015-08-26 IC ID: 579C-A1513 16 Revision History Date Report Name Changes to the report First Revision Report prepared by Douglas Antioco Douglas Antioco 2015-03-11 2015-08-20 EMC_ APPLE-144-14002_15.247_BTLE EMC_ APPLE-144-14002_15.247_BTLE_rev1 Replaced relevant references of RSS-210 to relevant references of RSS-247. Replace Bluetooth v4.0 with Bluetooth v4.2, added HVIN, PMN in section 3.1. Updated SW Version, EUT status. Deleted references to Peak power in Sections 5 and 7. Replaced References of 802.15 with Bluetooth LE. 2015-08-26 EMC_ APPLE-144-14002_15.247_BTLE_rev2 Replaces previous test Douglas Antioco report number. Updated Antenna and Rated Operating Voltage Range/Power Supply in section 3.1.

Conducted Test Setup AC Line Conducted Emissions Setup Front:

AC Line Conducted Emissions Setup Side:

Radiated Test Setup:

9KHz-30MHz 30MHz-1GHz 1-18GHz 18-26GHz