H12N1-20191107 Remote of Stakeboard User Manual 03 Function and operating instruction 1) Power Thank you for purchasing this ZYD product! The improper use may cause malfunction and damage to devices, so please make sure to read through this manual before use and strictly abide by the prescribed operating procedures. We are not liable for any liability arising from the use of this product, including but not limited to the reimbursement for Incidental or consequential losses. Meanwhile, we do not bear any responsibility for unauthorized modification of the product. We have the right to change the product design, appearance, performance and use requirements without notice. 01 Product Specification 1) Power on Press Powerkey on the remote control to power on. The remote control enters into connection mode. Press on/off if power on ESC, there are two sounds when power on. Note: The green indicator of remote control will flash after connection. If disconnect, the green indicator will be constant on. 2)
/
Power 2 Model
/
Battery voltage/Capacity Charging interface Communication mode Distance of remote control Applicable ESC H12N1 3.7V/220MAH Micro USB 2.4G 40mOpen area HW9032 02 Interactive mode 4) Diagram of remote control Acceleration braking roller
/
Switch button Forward button Battery indicator of remote control 10 2) Power off Manual off: Press Power for 2 seconds to power off. Automatical off: The romote control and scooter will power off automatically if not being operated within 10 minutes, if the scooter is at rest. 3) Power 3 5 1.5 12 3) Connect and match Press Power key on remote control for 3 seconds, and press controller switch for 5 seconds to enter into matching mode at any time. The contorller will make two short sounds every 1.5 seconds in matching mode. If there is a long sound, the matching is completed. It will exit matching mode if not being matched after 12 short sounds. The signal indicator of remote control will flash if match successfully then it can be used. 25%
25%
70% 40%-70% 10%-40%
, 10% 1 1 4) Battery indicator Battery indicator of remote of control:
After power on, if the battery of remote of control is less than 25%, the battery indicator of remote control flashes. Only brake is available and acceleration is unable at this time. If battery more than 25%, the indicator constantly on. Battery indicator of scooter:
When the battery is more than 70%, the battery indicator of scooter is all on. When the battery is between 40%-70%, two indicators on. When the battery is between 10%-40%, one indicator on. When the battery is less than10%, one indicator flashes,with a short sound every 1 second to warn. When the voltage is less thanthe safety voltage, close the power output, only brake is available. Note: Only battery of remote control displayed if the scooter was not connected. means constant on, means flash, means off, the same below. 5) /
Signal indicator Battery indicator of scooter 5) Throttle/brake control
/
Connect finger dial of throttle and brake and automatically enter into two-wheel scooter mode. Accelerate by adjusting finger dial of throttle. Brake by by adjusting finger dial of brake. Disconnect the finger dial of throttle and brake and enter into three-wheel scooter mode. Control acceleration and H12N1-20191107 Remote of Stakeboard User Manual NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help The device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 04 : Malfunction warning instruction:
brake by roller. Push roller forward to control scooter to go ahead. Pull roller backward to contorl scooter to brake. Note: Do not push/pull roller when press power key. 6) Reverse Reverse 3km/h 6) Switch direction of scooter In forward state, press Reverse key to switch from forward direction to backward mode;
In backward state, press Reverse key to switch from forward direction to forward mode;
Note: Forward direction only can be switched when the speed is less than3km/h. 1) 25%
10%, 1 1 2) 1.5 3 3) 4) 4 4 5) /
1) Battery low-voltage warning a) If the battery of remote of control is less than 25%, the battery indicator of remote control flashes. Only brake is available, need to charge remote control as soon as possible. b) When the battery of scooter is less than 10%, a single battery indicator of scooter flashes,with a short sound every second to warn. If the battery is too less, the throttle is unable and only the brake is available. Need to charge the scooter battery as soon as possible. 2) Signal loss warining The throttle will return to zero automatically when scooter loses the signal during accelerating, then brake slowly and automatically. It will ascend or reduce to a fixed braking force during braking. The remote control will search for scooter device after losing signal, with signal indicator is constantly on and three short sounds every 1.5 seconds to warn. The indicator and sound will return to normal if succeed to search and reconnect. Cancel slow brake and return the throttle to zero before normal operation. 3) Overheat warning When the temperature of controller is too high, the power output will weaken until the temperature returns to normal. Note: The users should keep an eye on the temperature of ESC and motor. When the operating temperature of ESC and motor is too high, the users should check the cause and use it after troublshooting. 4) Hardware malfunction warning If self-inspection hardware malfunction, the controller will make 4 short sounds every 4 seconds and stop power output. 5) Overcurrent /lock-up warning If the protection triggered, the controller will make a single short sound circularly and cut off power output. The output will be restored after the throttle returns to zero and has no malfunctions. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.