FCC ID: 2ADTD-CP04016405132 AX Hybrid

 

1

21

AX Hybrid

Quick Start Guide

2

2

23

24

Wi-Fi

E N G L I S H

Diagram References

Installation and Wiring

1

1-3.Install the device.

4. Wire Wi-Fi antenna.

Note: Power down the control panel before wiring accessories and peripherals.

2Peripherals/Power Supply Wiring

1. Alarm Input Wiring

a. NC Detector

b. NO Detector

c. Unoccupied Zone

2. Alarm Output Wiring

3. RS-485 Wiring: Wireless Receiver, keypad, etc.

4. Power Supply Wiring

d. Tamper-proof

e. Dual-Zone Series Connection

f. Dual-Zone Parallel Connection

5. Close and lock the case of the control panel.

2

Set Up

2

Note: After the user connects the power cord according to the figure, fix it with a cable

tie to avoid the cable falling off due to external force, causing a short circuit and other

dangers.

Set up via Web Client

For more activation methods ,refer to the User Manual.

Defacult IP Address:

Mobile broswer(AP mode):192.168.8.1

1. Enter the device IP address in the web browser.

2. Create a password for admin account to activate the device.

Reset:

After the device is started, hold the reset button for 10 seconds to reset the device.

The reset indicator will flash 3 times.

Specification

Model

Detector

Relay output

DS-PHA64-P2

UP to 64 (8 on-board, 56 wired/wireless)

DS-PHA64-W4P2

Up to 64 (4 on-board, 60 wired/wireless)

1 wired sounders (on-board connection)

2 wireless sounders

Device

connection

RS-485 wireless receiver

Up to 7

Sounder

Keyfob

Area

Alarm input

8

8

Function

Network camera

N/A

4

Protocol

Protocol

ISAPI, DC09, ISUP, CSV-IP, EZVIZ

Wi-Fi/AP

Standard

N/A

802.11b/g/n

User

User

Installer: 1; Administrator: 1;

Maintenance:1

Operator: 45

Tag/Card

Operation temperatue

12

–10 °C to 55 °C (-4 °F to 122 °F)

Others

Operation humidity

Dimension (W × H × D)

10% to 90% (No condensing)

310 mm (12.2") × 225 mm (8.6") × 95 mm

(3.7")

Weight

1.15 kg

1.17 kg

Note:

The 868 Mhz wireless sounder can be enrolled to the hybrid control panel

via the wireless receiver that is at the address of 9.

Fuse Cutout: rated voltage 250 V, rated current 6 A.

Mains supply cables need to meet IEC 60332 or UL certification.

AUX+ output interface: DC12 V, 1000 mA.

BELL+ output interface: DC12 V, 500 mA.

Allowed batteries specifications:

rated voltage 12 V, capacity 7Ah, Min. charging current ≥ 1 A,

flame class of shell V-0.

Peripherals/Power Supply Wiring

......

2b

2d

User Manual

Legal and Regulatory Information

Z1

C

Z2

Z3

C

Z4

Z5

C

Z6

Z7

C

Z8

C1 PGM1

C2 PGM2 C3 PGM3 C4 PGM4 AUX

AUX+

BELL

BELL+

D

D+

DC

DC+

BAT

BAT+

©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.

About this Manual

The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information

contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website

(https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

and other Hikvision's trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective

owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND

“WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR

A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR

INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF

DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT,

EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGESOR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS,

AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS

INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH

ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS

PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA

PROTECTION AND OTHER PRIVACY RIGHTS.YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS

DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR

FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to

your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific

battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to

your supplier or to a designated collection point. For more information see:www.recyclethis.info

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive

2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU

FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation

INSTALLATION CAUTION

1. The additional force shall be equal to three times the weight of the equipment but not less than 50N. The equipment and its associated mounting means shall remain secure during the

installation. After the installation, the equipment, including any associated mounting plate, shall not be damaged.

2. Install the equipment according to the instructions in this manual.

3. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions.

CAUTION

indicates hazardous live and the external wiring connected to the terminals requires installation by an instructed person.

●

● This equipment is suitable for mounting on concrete or other non-combustible surface only.Coper or coper wire cannot be exposed at the electrical terminal.

● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.

● CAUTION: To reduce the risk of fire, replace only with the same type and rating of fuse.

● A readily accessible disconnect device shall be incorporated external to the equipment, rated 6A.

● An all-pole mains switch shall be incorporated in the electrical installation of the building.

● Ensure correct wiring of the terminals for connection to an AC mains supply.

● The equipment has been designed, when required, modified for connection to an IT power distribution system.

● No naked flame sources, such as lighted candles, should be placed on the equipment.

● The serial port of the equipment is used for debugging only.

● Keep downward when moving or using the equipment.

Battery Caution

1. This equipment is not suitable for use in locations where children are likely to be present.

2. CAUTION: Risk of explosion if the battery is replaced by an incorrect type.

3. Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types).

4. Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.

5. Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas.

6. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.

7. Dispose of used batteries according to the instructions.

21

2a

2c

Security Control Panel

Z

C

N.C

N.C

N.C

N.C

N.C

N.C

N.C

N.C

N.O

N.O

N.O

N.O

N.O

N.O

N.O

N.O

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

Alarm

Lamp

Alarm

Lamp

Alarm

Lamp

Alarm

Lamp

Only for device with

8 on-board zones

Sounder

RS-485

Only for device with

8 on-board zones

22

C1

PGM1

AUX-

AUX+

D- D+

AUX-

AUX+

D- D+

Lead-acid

Battery

14.3VDC

Power Adapter

24

DC-

DC+

14.3V

Security Control Panel

Peripheral Security Detector

Security Control Panel

Peripheral Security Detector

Z

C

2.2KΩ

NC

C

Z

C

2.2KΩ

NO

C

2.2K Ω

TAMPER

Security

Control Panel

Local Zone

Security

Control Panel

Local Zone

Z

C

Ω

K

2

.

2

C

N

O

N

Detector

2e

Z

C

2.2kΩ

8.2kΩ

Local Expanding

Zone

Z

C

2.2kΩ

8.2kΩ

NC

C

NC

C

Local Expanding Zone

23

OR

……

f

Hangzhou Hikvision Digital Technology CO.,Ltd.

No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

UD23486B



 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a)

b)

c)

d)

e)

f)

g)

SGS North America Inc.

620 Old Peachtree Road

SUITE 100

Suwanee, Georgia 30024

United States

Applicant Declaration

Applicant Legal Business Name

Hangzhou Hikvision Digital Technology Co., Ltd.

No. 555 Qianmo Road, Binjiang District Hangzhou 310052, China

Address

Grantee Code

FCC ID

Contact Email

Contact Phone

Authorized Contact Name

Long Cheng

2ADTD

2ADTD-CP04016405132

chenglong6@hikvision.com

+8618969187825

I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my

knowledge and belief.

in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in

this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules,

if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure

that production units of this equipment will continue to comply with the FCC’s technical requirements.

in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible

party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321.

in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts

and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3)

the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS,

FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or

software required for evaluation, review, certification and audit surveillance of products certified by SGS.

neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section

5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See

47CFR 1.2002(b) for the definition of a “party” for these purposes.

the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions.

Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47

Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm

Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html

Date:2021/08/9

Applicant Signature:

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Long Cheng

Testing & Certification Engineer

Applicant Declaration

Rev:0.0



 

 

Hangzhou Hikvision Digital Technology Co., Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: 2021-08-09 Regarding: FCC ID: 2ADTD-CP04016405132 To whom it may concern:

We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Long Cheng Signature:

On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +8618969187825 Title: Testing & Certification Engineer

 

 

Confidentiality Request regarding application for FCC ID: 2ADTD-CP04016405132

SGS North America Inc.

620 Old Peachtree Road

SUITE 100

Suwanee, Georgia

United States

Hangzhou Hikvision Digital Technology Co., Ltd.

To:

From: Hangzhou Hikvision Digital Technology Co., Ltd.

No. 555 Qianmo Road, Binjiang District,

angzhou 310052, China

Regarding:

LONG TERM CONFIDENTIALITY

Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request

confidential treatment of the documents listed below, associated with the certification application

referenced above.

Schematic(s)

Block Diagrams

Operational Descriptions

The documents above contain proprietary information not released to the public. Public disclosure of this

information may prove harmful to the business of the applicant.

Sincerely,

Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Long Cheng

Title: Testing & Certification Engineer

Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.



 

 

Hangzhou Hikvision Digital Technology Co., Ltd. Device Installation Declaration Letter WE (Hangzhou Hikvision Digital Technology Co., Ltd.) HEREBY DECLARED THAT: The device (FCC ID:2ADTD-CP04016405132) is a professional installation device. The hardware cannot simply be purchased and installed by the average (technically inclined) person: 1)MarketingThe device cannot be sold retail, to the general public or by mail order. It must be sold todistributors. (Professional alarm installers or ARC)2)Requires professional installationThe device must be professionally installed and installation must be controlled. (EUT sold to distributor whohires installers with licensed professionals and special training)3)ApplicationThe device intended using in the residential, SMB and small commercial environment only.Thank you. Sincerely, Signature: . Name: Long Cheng . Data: 2021-08-11 .

 

 

Hangzhou Hikvision Digital Technology Co., Ltd.

Current Date : 2021-08-04

To:

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd.

No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612

Dear Sir/Madam,

Subject: Declaration Letter about Identity of Products

*WE (Hangzhou Hikvision Digital Technology Co., Ltd.) HEREBY DECLARED THAT

Product Description

AX Hybrid

Model No.

DS-PHA64-W4P2UHK, DS-PHA64-W4P2CKV,

DS-PHA64-W4P2UVS, DS-PHA64-W4P2KVO, DS-PHA64-W4P2HUN,

DS-PHA64-W4MUHK, DS-PHA64-W4MCKV, DS-PHA64-W4MUVS,

DS-PHA64-W4MKVO, DS-PHA64-W4MHUN

Manufacturer’s Name Hangzhou Hikvision Digital Technology Co., Ltd.

Manufacturer’s Address

No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

*Except that the model number, trade name, material and appearance deviation, are identical with the

original product as follows:

Note: 1.The definition of identical should be “electrically identical”. A device will be considered to be

electrically identical if no changes are made to the devices’ schematics, board layouts, component

layouts, chip sets, resistors and all other electrical aspects of the device are identical.

2. DS-PHA64-W4P2 shell material is plastic and DS-PHA64-W4M shell material is metal.

Model No. (型号):

DS-PHA64-W4P2, DS-PHA64-W4M

Manufacturer’s Name (生产商名称):

Hangzhou Hikvision Digital Technology Co., Ltd.

Manufacturer’s Address（生产商商地址):

No.555 Qianmo Road, Binjiang District, Hangzhou

310052, China

Sincerely,

Signature (签字):

Printed Name (姓名):

Long cheng

Position/Title (职位):

Testing & Certification Engineer

Contact Number (联系电话):

+8618969187825