FCC ID: 2ADTD-IPCR029 Camera

Camera Network Fisheye Camera Quick Start Guide UD.6L0201B1871A01 1 Network Fisheye CameraQuick Start Guide Quick Start Guide COPYRIGHT 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to 29xx Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website

(http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. 2 Network Fisheye CameraQuick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. 3 Network Fisheye CameraQuick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. 4 Network Fisheye CameraQuick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU, and the R&TTE Directive 1999/5/EC. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info 5 Network Fisheye CameraQuick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope 6 Network Fisheye CameraQuick Start Guide rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings 7 Network Fisheye CameraQuick Start Guide Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. Cautions Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. 8 Network Fisheye CameraQuick Start Guide Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time. The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. Do not place the camera in extremely hot, cold (the operating temperature shall be-30C ~+60C, or -40C ~ +60C if the camera model has an H in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for operating environment. Keep the camera away from liquid while in use. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. 9 Network Fisheye CameraQuick Start Guide If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) 10 Network Fisheye CameraQuick Start Guide Table of Contents 1.1 1.2 2.1 2.2 2.3 2.4 1 Appearance Description ............................................................... 12 Overview of Fisheye Camera ......................................... 12 Installing the SD Card .................................................... 13 2 Installation .................................................................................... 15 Ceiling Mounting ........................................................... 16 Wall Mounting with a Slant Mounting Base .................. 20 Wall Mounting with a Bracket ....................................... 24 Pendant Mounting with a Bracket ................................. 27 3 Setting the Network Camera over the LAN .................................. 29 Wiring ........................................................................... 29 Activating the Camera ................................................... 30 Activation via Web Browser ................................ 30 Activation via SADP Software ............................. 32 Modifying the IP Address .............................................. 33 4 Accessing via Web Browser .......................................................... 35 3.2.1 3.2.2 3.1 3.2 3.3 11 Network Fisheye CameraQuick Start Guide 1 Appearance Description 1.1 Overview of Fisheye Camera Figure 1-1 Overview of the Fisheye Camera 12 DC12VIN123456789 Network Fisheye CameraQuick Start Guide Table 1-1 Description of Overview No. Description Camera Body Power Interface RS-485 Interface Audio Interfaces: Audio In / Audio Out Alarm Interfaces: Alarm In / Alarm Out Ethernet Interface Reset Button Micro SD Card Slot Base Plate 1 2 3 4 5 6 7 8 9 The figures shown in this manual are for reference only. The appearance and interfaces of the camera are subject to the actual model. 1.2 Installing the SD Card Steps:

1. Move the Micro SD / Reset Cover aside, and you can see the reset button and the micro SD card slot. 2. Insert the micro SD card into the micro SD card slot. 13 Network Fisheye CameraQuick Start Guide 3. Re-cover the reset button and micro SD card slot. Figure 1-2 Install the SD Card Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 14 Micro SD / Reset CoverMicro SD Card Network Fisheye CameraQuick Start Guide 2 Installation Before you start:

Make sure the device in the package is in good condition and all the assembly parts are included. The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. Make sure all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Make sure that the wall is strong enough to withstand four times the weight of the camera and the bracket. For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:

Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly. 15 Network Fisheye CameraQuick Start Guide 2.1 Ceiling Mounting Steps:

1. Drill two screw holes and the cable hole according to the supplied drill template A. Figure 2-1 Drill Template A 2. Align the screw holes and cable hole on the drill template and the base plate, and then fix the base plate to the ceiling with the two supplied screws. 16 Network Fisheye CameraQuick Start Guide Figure 2-2 Fix the Base Plate For cement wall, you need to use the expansion screw to fix the mount. For wooden wall, you can just use the self-tapping screw to fix the mount. 3. Route the cables through the cable hole or the side opening according to the actual needs, and connect the corresponding cables including power cable, network cable, audio and alarm cables, etc. 4. Align the triangle mark on the camera and base plate, and then rotate the camera clockwise until it is locked up by the three bayonet joints on the base plate. 17 WallBase Plate Network Fisheye CameraQuick Start Guide Figure 2-3 Install the Camera 5. To disassemble the camera: Press the Push button on the base plate, rotate the camera anticlockwise, and then you can remove the camera from the base plate. Figure 2-4 Disassemble the Camera 18 WallBase PlateCameraBayonet JointBayonet JointBayonet JointWall Network Fisheye CameraQuick Start Guide 6. To adjust the view angle: Rotate the camera body clockwise or anticlockwise with the base plate, and then you can adjust the camera to the desired view angle. Figure 2-5 Adjust View Angle 7. To install the water-proof jacket for network interface (optional):

It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor. 1). If the network cable has been settled down, cut off the plug of the network cable first. 2). Route the network cable through the following components in sequence: fix nut, water-proof ring, and the main body of the water-proof jacket, as shown in the figure. 3). Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing ability of the components. 19 Network Fisheye CameraQuick Start Guide 4). Wire the plug and network cables up. 5). Fix the O-ring to the network interface of the camera, and then connect the network cables. 6). Wrap the network interface with the main body of the water-proof jacket, and then rotate the fix nut clockwise to assemble it to the main body of the water-proof jacket. Figure 2-6 Install Water-proof Jacket 2.2 Wall Mounting with a Slant Mounting Base The wall mounting with a slant mounting base provides a wider surveillance view compared to the wall mounting. You need to purchase a slant mounting base separately if this mounting method is selected. Steps:

1. Drill two screw holes and the cable hole according to the supplied drill template B. 20 Network InterfaceO-ringPlugWater-proof JacketWater-proof RingFix NutNetwork Cable Network Fisheye CameraQuick Start Guide Figure 2-7 Drill Template B 2. Fix the slant mounting base to the wall with the screws. Figure 2-8 Fix the Slant Mounting Base 3. Align the screw holes on the slant mounting base and the base plate, and then secure the base plate on the slant mounting base with the two supplied screws. 21 Mounting BaseWall Network Fisheye CameraQuick Start Guide 4. Route the cables through the cable hole or the side opening according to the actual needs, and connect the corresponding cables including power cable, network cable, audio and alarm cables, etc. 5. Align the triangle mark on the camera and mounting base, and then rotate the camera clockwise until it is locked up. Figure 2-9 Fix the Camera 6. The installation is complete. 22 Mounting BaseWallCamera Network Fisheye CameraQuick Start Guide Figure 2-10 Complete the Installation 7. To disassemble the camera: Press the Push button on the base plate, rotate the camera anticlockwise, and then you can remove the camera from the base plate. Figure 2-11 Disassemble the Camera 8. To install the water-proof jacket for network interface (optional), refer to the Step 7 in Section 2.1. 23 WallWallPUSH Network Fisheye CameraQuick Start Guide 2.3 Wall Mounting with a Bracket You need to purchase the bracket separately if this mounting method is selected. Steps:

1. Unfasten and remove the screw marked in the figure, and then disassemble the bracket. Figure 2-12 Disassemble the Bracket 2. Align the screw holes on the bracket and the base plate, and then secure the base plate on the bracket with the two supplied screws. 24 ScrewMounting Base Network Fisheye CameraQuick Start Guide Figure 2-13 Secure the Base Plate 3. Route the cables through the cable hole according to the actual needs, and connect the corresponding cables including power cable, network cable, audio and alarm cables, etc. 4. Align the triangle mark on the camera and base plate, and then rotate the camera clockwise until it is locked up by the three bayonet joints on the base plate. Figure 2-14 Fix the Camera 25 BracketBase PlateCable HoleBracketBase PlateCameraCable Hole Network Fisheye CameraQuick Start Guide 5. Fix the mounting base to the wall with the screws. Figure 2-15 Fix the Mounting Base 6. Re-install the main body of the bracket to the mounting base, and fix it with the screw. Figure 2-16 Re-install the Bracket 26 WallWallBracketScrew Network Fisheye CameraQuick Start Guide 7. To disassemble the camera, refer to the Step 5 in Section 2.1. 8. To adjust the view angle, refer to the Step 6 in Section 2.1. 9. To install the water-proof jacket for network interface (optional), refer to the Step 7 in Section 2.1. 2.4 Pendant Mounting with a Bracket You have to purchase the bracket separately if this mounting method is selected. 1. Fix the pendant bracket to the wall with the supplied screws. Figure 2-17 Fix the Bracket 2. Aim the screwed hole on the camera at the top of the pendant bracket, and then rotate the camera until it is secured tightly. 27 Wall Network Fisheye CameraQuick Start Guide Figure 2-18 Secure the Camera 3. Loosen the knob on the bracket and adjust the camera body to get the desired surveillance angle. Tighten the knob on bracket to secure the camera. Figure 2-19 Adjust the Angle 4. To install the water-proof jacket for network interface (optional), refer to the Step 7 in Section 2.1. 28 Top of BracketCamera WallTiltKnob on BracketPan Network Fisheye CameraQuick Start Guide 3 Setting the Network Camera over the LAN Note:

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.1 Wiring Please connect to the camera to the network according to the following figures Figure 3-1 Connecting Directly Figure 3-2 Connecting via a Switch or a Router 29 Network Fisheye CameraQuick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.1 Activation via Web Browser Steps:

1. Power on the camera, and connect the camera to the network. 2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface. Notes:

The default IP address of the camera is 192.168.1.64. For the camera enables the DHCP by default, you need to activate the camera via SADP software and search the IP address. 30 Network Fisheye CameraQuick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Confirm the password. 5. Click OK to save the password and enter the live view interface. 31 Network Fisheye CameraQuick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps:

1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Figure 3-4 SADP Interface Note:

The SADP software supports activating the camera in batch. Please refer to the user manual of SADP software for details. 32 Network Fisheye CameraQuick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If activation failed, please make sure that the password meets the requirement and try again. 3.3 Modifying the IP Address Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP software or client software to search and change the IP of network camera. We will take modifying the IP Address via SADP software as an example to introduce the IP address modification. Steps:

1. Run the SADP software. 2. Select an active device. 33 Network Fisheye CameraQuick Start Guide Note:

Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details. 34 Network Fisheye CameraQuick Start Guide 4 Accessing via Web Browser System Requirement:

Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:

1. Open the web browser. 2. In the browser address bar, input the IP address of the network camera, and press the Enter key to enter the login interface. Note:

The default IP address is 192.168.1.64. If the camera is not activated, please activate the camera first according to Chapter 3.2. 3. Input the user name and password. The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions. Note:

The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). 35 Network Fisheye CameraQuick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in. 36 Network Fisheye CameraQuick Start Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1) 37 Network Fisheye CameraQuick Start Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera. 38 0