DS-K1802 Series Card Reader User Manual DS-K1802 Series Card Reader User Manual 2019Hangzhou Hikvision Digital Technology Co., Ltd. About this Manual This Manual is applicable to DS-K1802series card reader This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd.
("Hikvision") reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Please use this user manual under the guidance of professionals. Trademarks and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF i DS-K1802 Series Card Reader THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. ii DS-K1802 Series Card Reader Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions iii DS-K1802 Series Card Reader This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply the applicable harmonized European standards listed under therefore with the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU
(WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed in the of as unsorted municipal waste product European Union. documentation battery information. The battery is marked with this symbol, which may lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info. the specific include See for Industry Canada ICES-003 Compliance iv DS-K1802 Series Card Reader This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. Use only power supplies listed in the user instructions:
Model Manufacturer Standard TS-A018-120015Ec Shenzhen Transin CEE Technologies Co., Ltd Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Follow Warnings safeguards serious injury or death. to these prevent Follow Cautions these precautions to prevent potential injury or material damage. Warnings All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value. v DS-K1802 Series Card Reader Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The appropriate temperature is -20 to 65. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. vi DS-K1802 Series Card Reader Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC power supply, which is nonswitched and linear. To guarantee the communication between the controller and the card reader, you must use RVVP cable above 0.5 to connect them. If the card reader is installed outside or in environment easy to permeable, it is advisable to install a waterproof shield. If you need to install several card readers, the distance among them must over 30cm. To reduce the noise in long distance transmission, the shield of cable should connect to the GND of both controller and card reader terminal. Please take care of your card and report card loss in time when card is lost. vii DS-K1802 Series Card Reader If you require a higher security level, use multiple authentication modes. Multiple card types are supported. Please select an appropriate card type according to the card performance and the usage scenarios. viii DS-K1802 Series Card Reader Content Chapter 2 Chapter 1 1.1 1.2 Introduction ........................................................ 2 Over View ...................................................................... 2 Indicator and Component .............................................. 3 Installation .......................................................... 3 2.1 Definition of Cable ......................................................... 3 2.2 Wiring Cables ................................................................ 4 Installing Card Reader .................................................... 4 2.3 Sound Prompt and Indicator ................................ 6 Chapter 3 ix DS-K1802 Series Card Reader Chapter 1 Introduction 1.1 Over View DS-K1802EK/MK/SK DS-K1802E/M/S Figure 1-1 DS-K1802 Series Card Reader DS-K1802 series card reader is a kind of high-performance product. It communicates with access controller via Wiegand protocol. As to the physical appearance, the PC+ABS material makes water proof and dust proof possible in poor environment. 2 DS-K1802 Series Card Reader 1.2 Indicator and Component Figure 1-2 Indicator and Component Chapter 2 Installation 2.1 Definition of Cable The description of cables is shown below. Table 2-1 Description of Cable Color Red Black Purple Brown Orange Green Description PWR (+12 VDC) GND Beep Control OK ERR Wiegand W0 3 Color White Blue DS-K1802 Series Card Reader Description Wiegand W1 Wiegand 26/ 34 2.2 Wiring Cables Purpose:
Wire the cables between controller and card reader, thus to establish the communication between them. Steps for Wiegand communication mode:
1. Set the Wiegand mode before power-on:
Cable Blue Wiegand Cable Wiring Method Wiegand Mode Wiegand 26 Wiegand 34 Not Grounded Grounded 2. Wiring the cable between controller and card reader as shown below. Figure 2-1 Wiring for Wiegand Communication Mode 2.3 Installing Card Reader Steps:
4 YellowBlueBlackRedBlackRedGreenWhitePurpleOrangeBrownControllerCard ReaderYellowBlueBlackRedBlackRedGreenWhitePurpleOrangeBrownControllerCard ReaderCard ReaderCard ReaderERROK DS-K1802 Series Card Reader 1. Fix the plate on the wall or other places by using two screws (PA425-SUS). Make sure the arrows on the plate are upwards. 2. Check whether the plate is fixed and in the right direction. 3. Slide the card reader from the direction A to B along the plate side until the bottom matches the joint. Make sure the card reader is tightly on the wall or other places. 4. Drag and move the card reader to make sure it is fixed. 5 DS-K1802 Series Card Reader Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn green and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information. Table 1-1 Description of Prompt Sound Sound Prompt Description Swiping card prompt Pressing keys prompt Prompt for too long card No. input by pressing keys. Time out prompt for pressing keys or swiping card. For Card + Password authentication:
prompt for entering the password after swiping the card. The operation of pressing keys or swiping card is valid. The operation of pressing keys or swiping card is invalid. Prompt for tamper-proof alarm. Prompt for buzzer alarm. The card reader is unencrypted. One beep Two rapid beeps Three slow beeps Rapidly continuous beeps Slowly continuous beeps 6 DS-K1802 Series Card Reader Table 1-2 Description of LED Indicator LED Indicator Status Green (blink for 1 time), and red (blink for 3 times) Green blinking and slow Solid green for 3s Solid red Red and blink for 3 times Description The card reader is power on. For Card + Password authentication:
prompt for entering the password after swiping the card. The operation of pressing keys or swiping card is valid. Card reader is working normally. The operation of pressing keys or swiping card is invalid. 0200001090515 7 DS-K1802 Series Card Reader UD05260B-A 8