FCC ID: 2ADTD-K1T342EFWX Face Recognition Terminal

1 Fingerprint Module USB Interface Loudspeaker UD25844B m m 3 1 8 1

. 91.3 mm 24.5 mm IR Light Camera MIC Camera Touch Screen Fingerprint Recognition Area/Card Presenting Area 2 Installation Environment:

Indoor use only. Avoid backlight, direct sunlight, and indirect sunlight. For Better recognition, there should be light source in or near the installation environment. The minimum bearing weight of the wall or other places should be 3 times heavier than the device weight. Wall Mounting Make sure the gang box is installed on the wall. Debugging Port (for debugging only) Wiring Terminal Network Interface Tamper Gang box is not supplied. Backlight Direct Sunlight Indirect Sunlight through Window Direct Sunlight through Window Close to Light Route the cable through the cable hole, wire the cables and insert the cables in the gang box. Apply Silicone sealant among the cable wiring area to keep the raindrop from entering. Apply Silicone sealant Secure the mounting plate on the gang box with two supplied screws (SC-KA4X22). Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw

(SC-KM3X6-T10-SUSS). 2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as Hikvision), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise expressly stated herein, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual, any information contained herein. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners. LEGAL DISCLAIMER TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED AS IS AND WITH ALL FAULTS AND ERRORS. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the effectiveness of your security controls. Scan the QR code to get the user manual for detailed information. Use only power supplies listed in the user instructions:

ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd PG PDE ADS-24S-12 1224GPG Shenzhen Honor Electronic Co., Ltd. PB 24.5 mm 91.3 mm Without Fingerprint Module USB Interface Loudspeaker 3 m m 3 1 8 1

. IR Light Camera MIC Camera Touch Screen Card Presenting Area Debugging Port (for debugging only) Wiring Terminal Network Interface Tamper Power Input RS-485 Wiegand Door Lock Network Port The figures are for reference only. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters. Do not wire the device to the electric supply directly. Activation via Device After powering on, you will enter the activation page. Steps:

1. Create a password and confirm the password. 2. Tap Acvate to acvate the device. Characters containing admin and nimda are not supported to be set as activation password. We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Set Language Select a language from the drop-down list. Set Application Mode Aer acvaon, you should select an applicaon mode. Select Indoor or Others from the drop-down list and tap OK. If you install the device indoors near the window or the face recognion funcon is not working well, select Others. Set Network Parameters Wired Network:

-If enable DHCP, the system will assign the IP address and other parameters automacally.

-If disable DHCP, you should manually set the IP address and other parameters. Wi-Fi:

-Select a Wi-Fi and enter the Wi-Fis password.

-Or tap Add Wi-Fi and enter the Wi-Fis name and password. If you select Wired Network, make sure the device has connected to a network. 4 5 Access to Hik-Connect Privacy Settings You can add the device to the Hik-Connect mobile client. Enable Hik-Connect, and set the Server IP and Verification Code. Set the privacy parameters, including the picture uploading and storage. Set Administrator Link to Mobile Client Download and install the mobile client Use the scan QR code funcon of the mobile client and scan the QR code on the device to link the device to the mobile client. Steps:

1. (Optional) Edit the employee ID. 2. Enter the administrator's name and tap OK. 3. Select a credentail to add. You can select face, card and fingerprint. to capture. And tap

--Add Face: Tap

--Add Fingerprint: Tap the fingerprint icon, and add fingerprint according to the prompt.

--Add Card: Swipe the card in the swiping area according to the prompt or enter the card number. to save. 4. Tap OK. Only the device with the fingerprint module supports the fingerprint functions. 1. Use finger to hold the screen surface for 3 s and slide to right/le and enter the acvaon password to enter the Home page. 2. Enter the User Management page, tap + to enter the Add User page. 3. Set the user parameters according to actual needs Only the device with the fingerprint module support the fingerprint related funcons. 4. Tap Face and add the face informaon according to the instrucons. You can view the captured picture on the screen. Make sure the face picture is in good quality and size. For details about the ps and posions when collecng or comparing the face picture, see the contents on the right. 5. If the picture is in good condion, tap to take another face picture. 6. Tap the save icon to save the sengs. Or tap

. Go back to the inial page to start authencaon. For other authencaon methods, see the device user manual. Use other authencaon methods if the device is affected by the light or other items. Biometric recognion products are not 100%

applicable to an-spoofing environments. If you require a higher security level, use mulple authencaon modes. Tips When Collecng/Comparing Face Picture Posions When Collecng/Comparing Face Picture Expression Keep your expression naturally when collecng or comparing face pictures just like the expression in the picture on the right Do not wear hat, sunglasses, or other accessories that can affect the facial recognion funcon. Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed. Posture In order to get a good quality and accurate face picture posion your face looking at the camera when collecng or comparing face picture. Size Make sure your face is in the middle of the collecng window. Safety Instruction Warning In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. The socket-outlet shall be installed near the equipment and shall be easily accessible. 1. Do not ingest battery. Chemical burn hazard!

2. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. 3. Keep new and used batteries away from children. 4. If the battery compartment does not close securely, stop using the product and keep it away from children. 5. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 6. CAUTION: Risk of explosion if the battery is replaced by an incorrect type. 7. Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). 8. Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion. 9. Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. 10. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. 11. Dispose of used batteries according to the instructions Caution Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden

(ignorance can cause fire danger). The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden

(ignorance can cause fire danger). Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. The serial port of the equipment is used for debugging only. Wall Mounting: Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. This bracket is intended for use only with equipped devices. Use with other equipment may result in instability causing injury. This equipment is for use only with equipped bracket. Use with other (carts, stands, or carriers) may result in instability causing injury. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium

(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info 2012/19/EU (WEEE directive):

Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

HIIK VISION Face Recognition Terminal Model: DS-K1T342EFWX WP: 12V24V=== 1A SN: AB1234567 ULAR roms Made in China FCC ID:2ADTD-K1T342EFWX This device complies with Part 15 of the FCC Rules. U K Operation is subject to the following two conditions: Cc A

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation. Manufacturer: Hangzhou Hikvision Digital Technology Co.,Ltd. Address: No.555 Qianmo Road, Binjiang District,Hangzhou 310052, China [a ost 733 ov LS SST INiwrs ce oo

*00l

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Hangzhou Hikvision Digital Technology Co., Ltd. Address Grantee Code FCC ID No. 555 Qianmo Road, Binjiang District Hangzhou 310052, China 2ADTD 2ADTD-K1T342EFWX Authorized Contact Name Long Cheng Contact Email Contact Phone chenglong6@hikvision.com

+8618969187825 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Date:2021/10/28 Applicant Signature:

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Long Cheng Testing & Certification Engineer Applicant Declaration Rev:0.0

Hangzhou Hikvision Digital Technology Co., Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ADTD-K1T342EFWX To whom it may concern:

Date: 2021-10-28 We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Long Cheng Title: Testing & Certification Engineer Signature:

On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +8618969187825

Hangzhou Hikvision Digital Technology Co., Ltd. To:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, angzhou 310052, China Regarding:

Confidentiality Request regarding application for FCC ID: 2ADTD-K1T342EFWX LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Long Cheng Title: Testing & Certification Engineer Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.

Hangzhou Hikvision Digital Technology Co., Ltd. Current Date : 2021-10-28 To:

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products

*WE (Hangzhou Hikvision Digital Technology Co., Ltd.) HEREBY DECLARED THAT Product Description Face Recognition Terminal Model No. DS-K1T342EFWUHK,DS-K1T342EFWCKV,DS-K1T342EFWUVS,DS-K1T3 42EFWKVO,DS-K1T342EFWHUN,DS-K1T342EWX,DS-K1T342EWUHK,D S-K1T342EWCKV,DS-K1T342EWUVS,DS-K1T342EWKVO,DS-K1T342EW HUN Manufacturers Name Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturers Address No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

*Except that the model number and appearance deviation, are identical with the original product as follows:

Note: The definition of identical should be electrically identical. A device will be considered to be electrically identical if no changes are made to the devices schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical. Model No. ():

DS-K1T342EFWX Manufacturers Name ():

Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturers Address):

No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Sincerely, Signature ():

Printed Name ():

Long Cheng Position/Title ():

Testing & Certification Engineer Contact Number ():

+8618969187825