FCC ID: 2ADTD-I0G2100 NETWORK CAMERA

Network Dome Camera Quick Start Guide DS-2CD2121G0-IWS/2AX 0 Network Dome CameraQuick Start Guide Quick Start Guide COPYRIGHT 2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to 21xx Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website

(http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and 1 Network Dome CameraQuick Start Guide logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE 2 Network Dome CameraQuick Start Guide APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information For products that support Wi-Fi or cellular data:

(Marked with a W, GLT, GLE, GLF, GE, GT or GW in the Part C of a product model. Product Model Example: Part A-Part B-Part C. Part C is optional.) FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. 3 Network Dome CameraQuick Start Guide Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Radio Equipment Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info 4 Network Dome CameraQuick Start Guide 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential 5 Network Dome CameraQuick Start Guide radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. For products that do not support Wi-Fi or cellular data:

FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency 6 Network Dome CameraQuick Start Guide energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 7 Network Dome CameraQuick Start Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. 8 Network Dome CameraQuick Start Guide Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. 9 Network Dome CameraQuick Start Guide Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Cautions Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time. The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. Do not place the camera in extremely hot, cold (the operating temperature shall be -30C to +60C, dusty or damp locations, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for operating environment. Keep the camera away from liquid while in use. 10 Network Dome CameraQuick Start Guide While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) 0505031071113 11 Network Dome CameraQuick Start Guide Table of Contents 2.1 2.2 2.3 2.4 1.1 1.2 1.3 1.4 1.5 1 Appearance Description ............................................................... 13 Type I ............................................................................ 13 Type II ........................................................................... 14 Type III .......................................................................... 16 Type IV .......................................................................... 18 Type V ........................................................................... 19 2 Installation .................................................................................... 22 Memory Card Installation .............................................. 23 Ceiling Mounting ........................................................... 24 Mounting with Brackets ................................................ 29

(Optional) Network Cable Waterproof Jacket Installation40 3 Set the Network Camera over the LAN ......................................... 43 Wiring ........................................................................... 43 Activate the Camera ...................................................... 44 Modify the IP Address ................................................... 47 4 Access via Web Browser ............................................................... 50 5 Operate via Hik-Connect App ....................................................... 52 5.1 Enable Hik-Connect Service on Camera ......................... 52 5.2 Hik-Connect Setup ........................................................ 55 5.3 Add Camera to Hik-Connect .......................................... 55 5.4 Initialize the Memory Card ............................................ 57 3.1 3.2 3.3 12 Network Dome CameraQuick Start Guide 1 Appearance Description There are five types of camera appearance for this series of camera according to the different models. 1.1 Type I Figure 1-1 Overview of Type I Camera Table 1-1 Description of Type I Camera No. Description No. Description 1 3 Mounting Base Vertical Stand 2 4 Horizontal Stand Bubble 13 12347891056 Network Dome CameraQuick Start Guide No. Description No. Description Network Interface IR LED Black Liner 6 8 10 Power Interface Lens Safety Rope 5 7 9 Note:

Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.2 Type II Figure 1-2 Overview Of Type II Camera 14 5123496781011*12*Network Dome CameraQuick Start Guide Table 1-2 Description of Type II Camera No. Description No. Description 1 3 5 7 9 Mounting Base Vertical Stand Network Interface IR LED 2 4 6 8 Horizontal Stand Bubble Power Interface Lens Black Liner 10 Safety Rope Audio Interface (Only Alarm Interface (Only 11*

supported by the camera 12*

supported by the camera with -S in its model) with -S in its model) Notes:

The items marked with the "*" are only supported by certain camera models. Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 15 Network Dome CameraQuick Start Guide 1.3 Type III Figure 1-3 Overview Of Type III Camera 16 5768143*DC12VIN2*910 Network Dome CameraQuick Start Guide Table 1-3 Description of Type III Camera Description Power supply interface (12 VDC) Audio input and output interface Alarm input and output interface RJ45 self-adaptive network interface (PoE) Mounting base Black liner Lens Bubble Memory card slot Reset button No. 1 2*

3*

4 5 6 7 8 9 10 Note:

The items marked with the "*" are only supported by certain camera models. Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 17 Network Dome CameraQuick Start Guide 1.4 Type IV Figure 1-4 Overview Of Type IV Camera 18 56143278 Network Dome CameraQuick Start Guide Table 1-4 Description of Type IV Camera No. Description 1 2 3 4 5 6 7 8 RJ45 self-adaptive network interface (supports PoE) HDMI Mounting base Black liner Lens Bubble Memory card slot Reset button Note:

Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 1.5 Type V 19 Network Dome CameraQuick Start Guide Figure 1-5 Overview Of Type V Camera Table 1-5 Description of Type V Camera No. Description No. Description Horizontal Stand Network Interface IR LED Black Liner 1 3 5 7 9 Mounting Base Bubble Power Interface Lens Safety Rope 2 4 6 8 20 123678945 Network Dome CameraQuick Start Guide Note:

Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 21 Network Dome CameraQuick Start Guide 2 Installation Before you start:

Make sure the device in the package is in good condition and all the assembly parts are included. The standard power supply is 12 VDC or PoE (802.3 af), please make sure your power supply matches with your camera. Make sure all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Make sure that the wall is strong enough to withstand four times the weight of the camera and the bracket. For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:

Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly. 22 Network Dome CameraQuick Start Guide 2.1 Memory Card Installation For camera models that support memory card as local storage, you can follow the steps to mount and unmount the memory card. This camera series shares a similar structure, type III camera is used for demonstration. Steps:

1. Loosen the screws on the bubble. Remove the bubble to expose the memory card slot. Figure 2-1 Remove Bubble Notes:

In case of losing, screws on bubble cannot be screwed out thoroughly. The bubble is fastened to the camera with a safety rope. 23 Network Dome CameraQuick Start Guide 2. Find the memory card slot to insert the memory card. Figure 2-2 Insert Memory Card 3.

(Optional) To unmount the memory card, push to get it ejected. 2.2 Ceiling Mounting This camera series shares a similar structure, type III camera is used for demonstration. Steps:

1. Paste the drill template to desired mounting place. 2. Drill the screw holes on the ceiling according to the drill template. 24 Network Dome CameraQuick Start Guide Figure 2-3 Drill Template Notes:

If you choose to route cable through the ceiling, cut a cable hole according to Hole A on drill template. You can also route cable from the side outlet. If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4. Side Outlet Figure 2-4 Side Outlet 25 111ADrill TemplateHole A: for cables routed through the ceilingScrew hole 1: for Mounting Base Network Dome CameraQuick Start Guide 3. Route the cables and fix the mounting base on the ceiling with three screws. Figure 2-5 Fix the Mounting Base 4. Adjust surveillance angle. See the figure of each camera type for detailed angle adjustment range 1). Loosen one tilting adjust adjusting screw to adjust the tilting position. Tighten the screw after adjustment. 2). Hold the black liner to adjust the panning position. 3). Hold the lens to adjust the rotating position. Note:

Rotating position adjustment is not supported by Type I camera. 26 Network Dome CameraQuick Start Guide Figure 2-6 Angle Adjustment of Type I Camera Figure 2-7 Angle Adjustment of Type II Camera 27 Tilting Adjust ScrewRotate: 0 to 355Pan:0 to 355Tilt: 0 to 750~3600~65Tilting AdjustScrew Network Dome CameraQuick Start Guide Figure 2-8 Angle Adjustment of Type III Camera 5. Install the bubble back to the camera. Figure 2-9 Install Bubble 28 Network Dome CameraQuick Start Guide 2.3 Mounting with Brackets This camera series supports mounting with wall mounting bracket, pendant mounting bracket, and incline mounting bracket. We take Type III camera as the demonstration example. 2.3.1 Wall Mounting The wall mounting bracket is not included in the package. You need to prepare one, if you adopt this mounting type. Steps:

1. Mark the screw holes on desired mounting place. Figure 2-10 Mark Screw Hole 29 HoleHoleHoleHole Network Dome CameraQuick Start Guide 2. Drill 4 screw holes for expansion screws. 3. Unscrew the bubble of the camera. 4. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 5. Route the cables and fix the camera to the cap of the wall mounting bracket with three supplied self-tapping screws. Figure 2-11 Fix the Camera to Wall Mounting Bracket 6. Align the wall mounting bracket to the screw holes and fix it to wall. Note:

If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4. 30 Wall Mounting BracketCable Hole Network Dome CameraQuick Start Guide Figure 2-12 Fix the Wall Mounting Bracket to Wall 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera. Figure 2-13 Install the Bubble 31 Network Dome CameraQuick Start Guide 2.3.2 Wall Mounting with Junction Box The wall mounting bracket with junction box is not included in the package. You need to prepare one, if you adopt this mounting type. Steps:

1. Mark the screw holes on desired mounting place. 2. Fix the bracket to the wall with four expansion bolts. Figure 2-14 Fix the Bracket 3. Unscrew the junction box cover. 32 Network Dome CameraQuick Start Guide Figure 2-15 Unscrew the Cover 4. Route and connect the cables. Source cables of network, power, etc., go in from the side outlet of the junction box. Camera cables go in from the cap and the bracket. Note:

If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4. 5. Screw the cover back. 33 Cover Network Dome CameraQuick Start Guide Figure 2-16 Cable Routing 6. Unscrew the bubble of the camera. 7. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 8. Fix the camera to the cap of the wall mounting bracket with three supplied self-tapping screws. 34 Source CableCamera Cable Network Dome CameraQuick Start Guide Figure 2-17 Fix the Camera to Wall Mounting Bracket 9. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 10. Install the bubble back to the camera. Figure 2-18 Install the Bubble 35 Network Dome CameraQuick Start Guide 2.3.3 Pendant Mounting The pendant mounting bracket is not included in the package. You need to prepare one in advance, if you adopt this mounting type. Steps:

1. Mark the screw holes on desired mounting place. 2. Drill three screw holes for expansion bolts. 3. Route the cables and fix the pendant mounting bracket to ceiling. Figure 2-19 Fix Pendant Mount 4. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 5. Fix the camera to the cap of the pendant mounting bracket with 3 supplied self-tapping screws. 36 Cables Network Dome CameraQuick Start Guide Figure 2-20 Fix the Camera to Cap 6. Screw the cap to the pendant mounting bracket. Figure 2-21 Install the Cap 37 Cap Network Dome CameraQuick Start Guide 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera. 2.3.4 Incline Mounting The incline mounting bracket is not included in the package. You need to prepare one, if you adopt this mounting type. Steps:

1. Paste the drill template to desired mounting place. Figure 2-22 Drill Template 2. Drill two screw holes for expansion screws, and a cable hole according to the template. 3. Fix the incline mounting bracket to ceiling. 38 Screw HoleCeiling MountingScrew HoleCable Hole Network Dome CameraQuick Start Guide Figure 2-23 Fix Incline Mounting Bracket to Wall 4. Unscrew the bubble of the camera. 5. (Optional) Insert the memory card to the camera, if your camera supports memory card installation. Refer to Section 2.1. 6. Route the cables and fix the camera to the incline mounting bracket with three supplied self-tapping screws. Note:

If you install the camera in outdoor, install the waterproof jacket to the network cable. See Section 2.4. Figure 2-24 Fix the Camera to Wall Mounting Bracket 39 Network Dome CameraQuick Start Guide 7. Adjust surveillance angle of camera. Refer to Step 4 in Section 2.2. 8. Install the bubble back to the camera. Figure 2-25 Install the Bubble

(Optional) Network Cable Waterproof 2.4 Jacket Installation Purpose:

If the camera is installed outdoor, you can adapt the waterproof accessory for the network cable after the camera is secured on the installation surface. 40 Network Dome CameraQuick Start Guide Figure 2-26 Waterproof Accessory Components Table 2-1 Components No. Components 1 2 3 4 5 6 7 Cameras Network Interface Socket O-Type Gasket Network Plug Waterproof Endcap Waterproof Rubber Gasket Lock Nut Network Cable from Router/Switch Steps:

1. Feed the plugless network cable through the lock nut , waterproof rubber gasket (rubber gasket inset ridge must face waterproof endcap), and the waterproof endcap in order. 2. Crimp an RJ-45 network plug onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. 41 Network Dome CameraQuick Start Guide 3. Place the O-type gasket onto the end of the cameras network interface socket . 4. Insert the network plug into the cameras network interface socket . 5. Insert the waterproof rubber gasket into the waterproof endcap , and secure lock nut with the waterproof endcap . 6. Align the snap on the waterproof endcap with the notch on the cameras network interface socket , and then secure the waterproof endcap to the cameras network interface socket to finish installation. Figure 2-27 Waterproof Accessory Installation 42 CameraSwitch/RouterAlign the snap and notch.i. Insert into .ii. Secure with . Network Dome CameraQuick Start Guide 3 Set the Network Camera over the LAN Note:

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures. Figure 3-1 Connecting Directly Figure 3-2 Connecting via a Switch or a Router 43 Network CableorNetwork Camera Computer Network CableNetwork CableororNetwork Camera Computer Network Dome CameraQuick Start Guide 3.2 Activate the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are all supported. We will take activation via SADP software and activation via web browser as examples to introduce the camera activation. Note:

Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.1 Activation via Web Browser Steps:

1. Power on the camera. Connect the camera to your computer or the switch/router which your computer connects to. 2. Input the IP address into the address bar of the web browser, and press Enter to enter the activation interface. Notes:

The default IP address of the camera is 192.168.1.64. The computer and the camera should belong to the same subnet. For the camera enables the DHCP by default, you need to use the SADP software to search the IP address. 44 Network Dome CameraQuick Start Guide Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Confirm the password. 5. Click OK to save the password and enter the live view interface. 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. 45 Network Dome CameraQuick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps:

1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Figure 3-4 SADP Interface Note:

The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details. 3. Create and input the new password in the password field, and confirm the password. 46 Select inactive device.Input and confirm password. Network Dome CameraQuick Start Guide STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. Note:

You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Click Activate to start activation. You can check whether the activation is completed on the popup window. If activation failed, make sure that the password meets the requirement and try again. 3.3 Modify the IP Address Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Use the SADP software or client software to search and change the IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification. For IP address modification via client software, refer to the user manual of client software. 47 Network Dome CameraQuick Start Guide Steps:

1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking Enable DHCP. Figure 3-5 Modify the IP Address 48 Network Dome CameraQuick Start Guide Note:

You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details. 49 Network Dome CameraQuick Start Guide 4 Access via Web Browser System Requirement:

Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:

1. Open the web browser. 2. In the browser address bar, input the IP address of the network camera, and press the Enter key to enter the login interface. Note:

The default IP address is 192.168.1.64. You are recommended to change the IP address to the same subnet with your computer. 3. Input the user name and password. The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions. Note:

The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). 50 Network Dome CameraQuick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note:

You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login. Note:

For detailed instructions of further configuration, please refer to the user manual of network camera. 51 Network Dome CameraQuick Start Guide 5 Operate via Hik-Connect App Purpose:

Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note:

Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose:

Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.1 Enable Hik-Connect Service via SADP Software Steps:

1. Check the checkbox of Enable Hik-Connect on:

1). "Activate the Device" page during camera activation, refer to Chapter 3.2.2. 2). Or "Modify Network Parameters" page during modifying IP address, refer to Chapter 3.3. 2. Create a verification code or change the verification code. 52 Network Dome CameraQuick Start Guide Figure 5-1 Verification Code Setting (SADP) Note:

The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start:

You need to activate the camera before enabling the service. Refer to Chapter 3.2. 53 Network Dome CameraQuick Start Guide Steps:

1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration >

Network > Advanced Settings > Platform Access. Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera. Note:

The verification code is required when you add the camera to Hik-Connect app. 7. Save the settings. 54 Network Dome CameraQuick Start Guide 5.2 Hik-Connect Setup Steps:

1. Download and install the Hik-Connect app by searching Hik-Connect in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Add Camera to Hik-Connect Before you start:

You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to Chapter 5.1. Steps:

1. Use a network cable to connect the camera with a router if the camera does not support Wi-Fi. Figure 5-3 Connect a Router Note:

After the camera connects to the network, please wait one minute before any operation on the camera using Hik-Connect app. 2. In the Hik-Connect app, tap + on the upper-right corner and then scan the QR code of the camera to add the camera. 55 Network Dome CameraQuick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note:

If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the camera's serial number. icon and inputting the 3. Input the verification code of your camera. Note:

The required verification code is the code you create or change when you enabling Hik-Connect service on camera. If you forget the verification code, you can check the current verification code on Platform Access configuration page via web browser. 4. Follow the prompts to set the network connection and add the camera to your Hik-Connect account. Note:

For detailed information, refer to the user manual of the Hik-Connect app. 56 Network Dome CameraQuick Start Guide 5.4 Initialize the Memory Card Steps:

Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection. 57 UD07705B 0

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 8 Internal Photos Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Applicant:

Address of Applicant:

Equipment Under Test (EUT):

Product Name:

Model No.:

NETWORK CAMERA DS-2CD2121G0-IWS/2AX Page 1 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 8 Page 2 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 8 Page 3 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 4 of 8 Page 4 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 5 of 8 Page 5 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 6 of 8 Page 6 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 7 of 8 Page 7 of 8 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 8 of 8 End Page 8 of 8

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 1 of 3 External Photos Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, Hangzhou 310052, China Applicant:

Address of Applicant:

Equipment Under Test (EUT):

Product Name:

Model No.:

NETWORK CAMERA DS-2CD2121G0-IWS/2AX Page 1 of 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 2 of 3 Page 2 of 3 SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Page: 3 of 3 End Page 3 of 3

Hangzhou Hikvision Digital Technology Co., Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ADTD-I0G2100 To whom it may concern:

Date: 2019-7-12 We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed):Xiuying Zhang Title: Global Certification Team Lead Signature:

On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +86-0571-88075998-62460

No. 555 Qianmo Road, Binjiang District, angzhou 310052, China Confidentiality Request regarding application for FCC ID: 2ADTD-I0G2100 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States Hangzhou Hikvision Digital Technology Co., Ltd. To:

From: Hangzhou Hikvision Digital Technology Co., Ltd. Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Xiuying Zhang Title: Global Certification Team Lead Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.