FCC ID: 2ADTD-DS-2DE3 PTZ Camera

Network PTZ CameraQuick Start Guide Network PTZ Camera Quick Start Guide i Network PTZ CameraQuick Start Guide Quick Start Guide COPYRIGHT 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to Network PTZ Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website

(http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. i Network PTZ CameraQuick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. ii Network PTZ CameraQuick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. 0505171080913 iii Network PTZ CameraQuick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive iv Network PTZ CameraQuick Start Guide 2015/35/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, please see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information, please see: www.recyclethis.info. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. v Network PTZ CameraQuick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Refer to technical specifications for detailed information. Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information. vi Network PTZ CameraQuick Start Guide Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Make sure that the plug is firmly connected to the power socket. Make sure that the power has been disconnected before you wire, install or dismantle the PTZ camera. When the product is mounted on wall or ceiling, the device shall be firmly fixed. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then contact the service center. If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions If the camera fails to synchronize local time with that of the network, you need to set up camera time manually. Visit the camera (via web browser or client software) and enter system settings interface for time settings. Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid installation on vibrations surface or places subject to shock (ignorance can cause device damage). vii Network PTZ CameraQuick Start Guide Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time. The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. Do not place the camera in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for operating environment. Keep the camera away from liquid while in use. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. viii Network PTZ CameraQuick Start Guide Table of Contents 1 Overview ...................................................................................... 1 1.1 Introduction ............................................................................. 1 1.2 Cable Descriptions .................................................................... 1 1.3 Alarm Output ........................................................................... 2 2 Installation ................................................................................... 4 2.1 Installing the Memory Card ...................................................... 4 2.1.1 DE1Axxx(I) Series PTZ Camera ........................................... 4 2.1.2 DE2Axxx(I) Series PTZ Camera ........................................... 8 2.1.3 DE2xxx(I) Series PTZ Camera ............................................. 8 2.1.4 DE3xxx Series PTZ Camera ................................................. 9 2.1.5 DY3xxx Series PTZ Bullet Camera ..................................... 10 2.1.6 DE4AxxxI Series PTZ Camera............................................ 10 2.2 Installing DE1Axxx(I) Series PTZ Camera ................................. 12 2.2.1 Ceiling Mounting ............................................................. 14 2.2.2 Wall Mounting ................................................................. 16 2.3 Installing DE2Axxx(I) Series PTZ Camera ................................. 18 2.4 Installing DE2xxx(I) Series PTZ Camera.................................... 18 2.4.1 Wall Mounting ................................................................. 19 2.4.2 Ceiling Mounting ............................................................. 23 2.4.3 Installing with Junction Box ............................................. 28 2.5 Installing DE3xxx Series PTZ Camera ....................................... 31 2.5.1 Ceiling Mounting ............................................................. 31 2.5.2 In-ceiling Mounting ......................................................... 33 2.6 Installing DY3xxx Series PTZ Bullet Camera ............................. 36 2.6.1 Dimensions of DY3xxx Series PTZ Bullet Camera ............. 36 2.6.2 Wall Mounting ................................................................. 38 2.6.3 Base Mounting ................................................................ 39 ix Network PTZ CameraQuick Start Guide 2.7 Installing DE4AxxxI Series PTZ Camera .................................... 40 2.7.1 Ceiling Mounting ............................................................. 41 2.7.2 In-ceiling Mounting ......................................................... 41 3 Setting the PTZ Camera over the LAN ......................................... 44 3.1 Wiring .................................................................................... 54 3.2 Activating the Camera ............................................................ 55 3.2.1 Activation via Web Browser ............................................. 55 3.2.2 Activation via SADP Software .......................................... 57 3.3 Modifying the IP Address ........................................................ 58 4 Accessing via Web Browser ........................................................ 61 5 Operating via Hik-Connect App .................................................. 64 5.1 Enable Hik-Connect Service on Camera .................................. 64 5.1.1 Enable Hik-Connect Service via SADP Software ............... 64 5.1.2 Enable Hik-Connect Service via Web Browser ................. 65 5.2 Hik-Connect Setup .................................................................. 67 5.3 Adding Camera to Hik-Connect ............................................... 67 5.4 Initializing the Memory Card .................................................. 69 x Network PTZ CameraQuick Start Guide 1 Overview 1.1 Introduction The network PTZ camera has the following series:

DE1Axxx(I) Series PTZ Camera DE2Axxx(I) Series PTZ Camera DE2xxx(I) Series PTZ Camera DE3xxx Series PTZ Camera DY3xxx Series PTZ Bullet Camera DE4AxxxI Series PTZ Camera Integrated with an optical zoom lens, this series of cameras feature in the PTZ limits, 3D positioning, Day/Night auto switch, 3D DNR, etc., and are widely applied in various kinds of environments. 1.2 Cable Descriptions The cable interfaces of network PTZ camera are shown in Figure 1-1. The cables are distinguished by different colors. Refer to the labels attached on the cables for identification. Notes:

Make sure the camera is power-off before you connect the The cables vary depending on different camera models. cables. 1 Network PTZ CameraQuick Start Guide Power Cord DC12V IN Video Cable RS-485 Alarm Cable

... Audio Cable Network Cable Figure 1-1 Cables of PTZ Camera Power Cord: Supports 12 VDC power supply. Video Cable: Connect BNC Cable to test the video output. Alarm Cable: Connect terminal ALARM-IN with GND interface, and connect terminal ALARM-OUT with ALARM-COM interface. Audio Cable: Connect terminal AUDIO-IN with GND interface. Network Cable: Connect the network interface with network cable. 1.3 Alarm Output Alarm output is shown in Figure 1-2. 2 Network PTZ CameraQuick Start Guide Direct load Relay Output OUT (n) OUT (n)

+

-

DC Relay Output OUT (n) OUT (n) GND Output DC 30V 1A Power Supply JQC-3FG Relay

(10A 250VAC)

~220V AC Zero Line FireWire Figure 1-2 Alarm Output 3 Network PTZ CameraQuick Start Guide 2 Installation Before you start:

Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes:

Do not drag the PTZ camera with its waterproof cables;

otherwise the waterproof performance is affected. Do not touch the bubble directly by hand. The image blurs otherwise. Do not power up the camera until the installation is finished. To ensure the safety of personnel and equipment, all the installation steps should be done with power supply off. 2.1 Installing the Memory Card You can install the memory card for local storage. 2.1.1 DE1Axxx(I) Series PTZ Camera Steps:

1. Open the cover with the straight screwdriver from a crack on the cover, as shown in Figure 2-1. 4 Network PTZ CameraQuick Start Guide Crack Cover 2.0 Figure 2-1 Open the Cover 2. Unscrew the screws on the camera base with the cross screwdriver, and remove the bubble, as shown in Figure 2-2. Bubble Screw Figure 2-2 Remove the Bubble 3. The position of memory card are various according to different camera model. Type I: open the memory card slot in the camera, and insert the memory card. 5 Network PTZ CameraQuick Start Guide Reset Memory Card Slot Figure 2-3 Insert the Memory Card Type II: align the memory card with the memory card slot and insert it. Reset Memory Card Slot Figure 2-4 Insert the Memory Card 4. Align the bubble with the camera base, and install the bubble back. Fix the bubble with four screws, as shown in Figure 2-5. 6 Network PTZ CameraQuick Start Guide Figure 2-5 Install the Bubble 5. Align the cover with the camera, and install the cover back, as shown in Figure 2-6. Cover Figure 2-6 Install the Cover 7 Network PTZ CameraQuick Start Guide 2.1.2 DE2Axxx(I) Series PTZ Camera Note:

The installation steps are similar to the installation steps of DE1Axxx(I) series camera. Refer to section 2.1.1 DE1Axxx(I) Series PTZ Camera. 2.1.3 DE2xxx(I) Series PTZ Camera Steps:

1. Open the memory card cover. Memory Card Cover Figure 2-7 DE2xxx Series PTZ Camera Memory Card Cover Figure 2-8 DE2xxxI Series (IR) PTZ Camera 8 Network PTZ CameraQuick Start Guide 2. Rotate the cover to a proper position, align the memory card with the memory card slot and insert it. Figure 2-9 Insert the Memory Card 3. Rotate the cover and push it back. 2.1.4 DE3xxx Series PTZ Camera Steps:

1. Loosen three screws on the bottom of camera to reveal the memory card slot, as shown in Figure 2-10. Reset Debug Memory Card Figure 2-10 DE3xxx Series PTZ Camera 9 Network PTZ CameraQuick Start Guide 2. Align the memory card with the memory card slot and insert it. 3. Fix the screws and assemble the PTZ camera. 2.1.5 DY3xxx Series PTZ Bullet Camera For DY3xxx series PTZ bullet camera, the memory card slot is in the camera module and if you need, the memory card can be installed before the camera leaves the factory. In order to prevent damage, we highly recommend that you do not disassemble the PTZ bullet camera by yourself. 2.1.6 DE4AxxxI Series PTZ Camera Steps:

1. Remove the four silicone plugs on the decorative rim as shown in Figure 2-11, and you can see four flange screws in the decorative rim. Decorative Rim Silicone Plug Figure 2-11 Remove the Silicone Plugs 2. Loosen four flange screws with a screwdriver. Remove the bubble and the decorative rim as shown in Figure 2-12. 10 Network PTZ CameraQuick Start Guide Bubble Decorative Rim Flange Srews Figure 2-12 Remove the Bubble and the Decorative Rim 3. Open the memory card cover and insert the memory card into the card slot as shown in Figure 2-13 and Figure 2-14. Memory Card Slot Memory Card Cover Figure 2-13 For 20 Camera Module 11 Network PTZ CameraQuick Start Guide Memory Card Slot Memory Card Cover Figure 2-14 For 4 Camera Module 4. Close the memory card cover. Fix the four flange screws and push four silicone plugs back to assemble the PTZ camera. 2.1.7 DE3AxxxI Series PTZ Camera Steps:

1. Pull the decorative cover out and loosen 2 screws on memory card cover with screwdriver as shown in Figure 2-15. Memory card cover Figure 2-15 Open the memory card cover 12 Network PTZ CameraQuick Start Guide 2. Remove the memory card cover, including sealing ring, and insert the memory card as printed mark. Memory card Figure 2-16 Insert the memory card 3. Screw the memory cover back, making sure the sealing ring is flat, and then close the decorative cover. Figure 2-17 Complete the memory card installation 13 Network PTZ CameraQuick Start Guide 2.2 Installing DE1Axxx(I) Series PTZ Camera 2.2.1 Ceiling Mounting Notes:

Make sure the ceiling is strong enough to withstand more than The thickness of the ceiling shall range from 5 mm to 40 mm. four times the weight of the PTZ camera and its accessories. Steps:

1. Rotate the installation plate anticlockwise, and remove the installation plate, as shown in Figure 2-15. OPEN Installation Plate Figure 2-18 Remove the Installation Plate 2. Drill four screw holes in the ceiling according to the installation plate. 3. Align the installation plate with the screw holes, and fix the installation plate on the ceiling. 14 Network PTZ CameraQuick Start Guide Figure 2-19 Fix the Installation Plate 4. Route the cables from the cable hole in the installation plate. Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 5. Align the camera with the installation plate, and rotate the camera clockwise to fix it, as shown in Figure 2-17. LOCK OPEN Figure 2-20 Fix the Camera 15 Network PTZ CameraQuick Start Guide 2.2.2 Wall Mounting Notes:

For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps:

1. Remove the installation plate, and install it on the wall mounting bracket (not supplied) with two screws. Note:

Refer to step 1 in section 2.2.1 Ceiling Mounting to remove the installation plate. Figure 2-21 Install the Installation Plate 2. Loosen the fixing screw on the bracket and remove the bracket base. 16 Network PTZ CameraQuick Start Guide Fixing Screw Bracket Base Figure 2-22 Remove the Bracket Base 3. Install the bracket base on the wall with four screws. Figure 2-23 Install the Bracket Base 4. Route the cables. Align the camera with the installation plate on the wall mounting bracket, and rotate the camera clockwise to fix it on the bracket. OPEN LOCK Figure 2-24 Install the Camera 17 Network PTZ CameraQuick Start Guide 5. Connect the cables. Install the wall mounting bracket to the bracket base on the wall, and fix it with the supplied screw. Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. Figure 2-25 Fix the Bracket 6. Remove the protective film after installation. 2.3 Installing DE2Axxx(I) Series PTZ Camera Note:

The installation steps are similar to the installation steps of DE1Axxx(I) series camera. Refer to section 2.2 Installing DE1Axxx(I) Series PTZ Camera. 2.4 Installing DE2xxx(I) Series PTZ Camera DE2xxx series PTZ camera supports wall mounting, ceiling mounting, and installing with junction box. DE2xxxI Series (IR) PTZ camera supports wall mounting and ceiling mounting. 18 Network PTZ CameraQuick Start Guide 2.4.1 Wall Mounting Notes:

For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps:

1. Rotate the base plate counterclockwise to separate it from the PTZ camera. OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-26 Base Plate for DE2xxx Series PTZ Camera 19 Network PTZ CameraQuick Start Guide OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-27 Base Plate for DE2xxxI Series (IR) PTZ Camera 2. Align the cable hole on the base plate with the hole on the bracket for wiring. And install the base plate to the bracket by fixing three PM410 screws (supplied) to the holes marked with digit 2 on the bracket. Figure 2-28 For DE2xxx Series PTZ Camera 20 Network PTZ CameraQuick Start Guide Figure 2-29 For DE2xxxI Series (IR) PTZ Camera 3. Route the cables through the cable hole. 4. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise to the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. OPEN LOCK Figure 2-30 Secure DE2xxx Series PTZ Camera 21 Network PTZ CameraQuick Start Guide OPEN LOCK Figure 2-31 Secure DE2xxxI Series (IR) PTZ Camera 5. Secure the mounting base to the wall with four PA425 screws

(supplied). Figure 2-32 Install the Mounting Base 6. Install the PTZ camera to the bracket. 1). Route the cables of the PTZ camera through the wall bracket. 2). Connect the corresponding cables. 3). Hang the bracket together with the PTZ camera on the mounting base. 4). Fix the mounting base with a PM410 screw. 22 Network PTZ CameraQuick Start Guide Figure 2-33 Secure the Mounting Base Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 2.4.2 Ceiling Mounting Purpose:

There are two ceiling mounting types provided for the camera, and we take the mounting without the junction box as the example. Notes:

The ceiling mounting is applicable to the indoor/outdoor solid ceiling construction. The followings are the mandatory precondition for ceiling mounting:

The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories. Wiring The cables of PTZ camera can be routed either from the top or the side of the back box, as shown in Figure 2-31 and Figure 2-32. 23 Network PTZ CameraQuick Start Guide For the cables routed from the top of the back box, it is required to drill a cable hole in the ceiling. Figure 2-34 Cabling for DE2xxx Series PTZ Camera Figure 2-35 Cabling for DE2xxxI Series (IR) PTZ Camera Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. Ceiling Mounting without Junction Box Steps:

1. Rotate the base plate counterclockwise to separate it from the PTZ camera, as shown in Figure 2-23 and Figure 2-24. 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and make sure the front arrow appoints to the monitoring area. 24 Network PTZ CameraQuick Start Guide Figure 2-36 Attach the Drill Template 3. Drill a cable hole in the ceiling according to the circle A on the template if you want to route the cables through the ceiling. Pull out the cable slot cover if you want to route the cables on the surface of the ceiling, as shown in Figure 2-34. Cable Slot Cover Figure 2-37 For DE2xxx Series PTZ Camera 25 Network PTZ CameraQuick Start Guide Cable Slot Cover Figure 2-38 For DE2xxxI Series (IR) PTZ Camera 4. Attach the base plate to the ceiling and secure it with the supplied three self-tapping screws by aligning with three screw holes in the ceiling, and the front arrows on the drill template and base plate should be aligned together as well, as shown in Figure 2-36 and Figure 2-37. Figure 2-39 For DE2xxx Series PTZ Camera 26 Network PTZ CameraQuick Start Guide Figure 2-40 For DE2xxxI Series (IR) PTZ Camera 5. Route the cables through the cable hole. 6. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. OPEN LOCK OPEN LOCK Figure 2-41 Secure the PTZ Camera 27 Network PTZ CameraQuick Start Guide 2.4.3 Installing with Junction Box Notes:

Make sure the ceiling is strong enough to withstand more than The thickness of the ceiling shall range from 5 mm to 40 mm. four times the weight of the PTZ camera and its accessories. Steps:

1. Rotate the base plate counterclockwise to separate it from the PTZ camera. Notes:

The base plate is not required when you install the PTZ camera with junction box. Keep it properly. The junction box is the optional accessory. Get it prepared before installation. OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-42 For DE2xxx Series PTZ Camera 28 Network PTZ CameraQuick Start Guide OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-43 For DE2xxxI Series (IR) PTZ Camera 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and make sure the front arrow appoints to the monitoring area. 3. Insert two PM410 screws into the ceiling, as shown in Figure 2-41. Figure 2-44 Attach the Drill Template 4. Attach the junction box to the ceiling and secure it by aligning the holes with two screws and rotating the junction box according to the direction as shown in Figure 2-42. Make sure the front arrows 29 Network PTZ CameraQuick Start Guide on the drill template and junction box should be aligned together as well. Figure 2-45 Fix the Junction Box 5. Connect the cables and route the cables clockwise through the hooks and fix the camera and the junction box with three hooks. Tighten it clockwise and loosen it anticlockwise. Cable Outlet OPEN LOCK Figure 2-46 Fix the Camera 30 Network PTZ CameraQuick Start Guide 6. Secure the PTZ camera and remove the protective film. 2.5 Installing DE3xxx Series PTZ Camera DE3xxx series PTZ camera supports ceiling mounting and in-ceiling mounting. Note:

Wall mounting, installation with junction box, and installation with tripod are supported for DE3xxx series PTZ camera. The corresponding accessories shall be purchased separately. 2.5.1 Ceiling Mounting Notes:

Make sure the ceiling is strong enough to withstand more than The thickness of the ceiling shall range from 5 mm to 40 mm. four times the weight of the PTZ camera and its accessories. Steps:

1. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and make sure the front arrow appoints to the monitoring area. 2. Drill a cable hole in the ceiling according to the circle A on the template if you want to route the cables through the ceiling, as shown in Figure 2-44. 31 Network PTZ CameraQuick Start Guide Figure 2-47 Attach the Drill Template 3. Insert the expansion screws into the ceiling. (Optional) 4. Insert four PM410 screws into the ceiling and fix the base plate, as shown in Figure 2-45. Make sure the FRONT arrow of the base plate is of the same direction as the arrow of the drill template. Figure 2-48 Fix the Base Plate 5. Connect the cables and route the cable through the cable outlet. Align the PTZ camera with the base plate. Rotate the PTZ camera 32 Network PTZ CameraQuick Start Guide clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 6. Fix the screws on the side with a screwdriver, as shown in Figure 2-46. OPEN LOCK Figure 2-49 Fix the Camera 7. Secure the PTZ camera and remove the protective film. 2.5.2 In-ceiling Mounting Notes:

Reserve at least 250 mm of height for in-ceiling mounting. Make sure the ceiling is strong enough to withstand more than The thickness of the ceiling shall range from 5 mm to 40 mm. four times the weight of the PTZ camera and its accessories. Steps:

33 Network PTZ CameraQuick Start Guide 1. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and drill a hole in the ceiling according to the template. Figure 2-50 Drill Template 2. Fix the base plate onto the in-ceiling bracket with the four screws in the package (supplied). Make sure that the cable holes of the base plate are aligned to the cable holes of the bracket, as shown in Figure 2-48. Figure 2-51 Fix the Base Plate to In-ceiling Bracket 34 Network PTZ CameraQuick Start Guide 3. Connect the cables and route the cable through the cable hole. Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 4. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 5. Fix the screws on the side with a screwdriver, as shown in Figure 2-49. OPEN LOCK Figure 2-52 Fix the Camera 6. Fix the decorative rim with the bubble and the decorative rim will be attached to the in-ceiling bracket automatically, as shown in Figure 2-50. 35 Network PTZ CameraQuick Start Guide Figure 2-53 Assemble the Decorative Rim 7. Secure the camera and remove the protective film. 2.6 Installing DY3xxx Series PTZ Bullet Camera 2.6.1 Dimensions of DY3xxx Series PTZ Bullet Camera Two structures of DY3xxx Series PTZ bullet cameras are available:

wall-mounted PTZ bullet camera and base-mounted PTZ bullet camera. Select the proper PTZ bullet camera and the installation method according to its working environment. Dimensions of wall-mounted PTZ bullet camera is shown in Figure 2-51. 36 Network PTZ CameraQuick Start Guide 157 367 242 105 4-7

(74.2) 122

(74.2) Unit: mm Figure 2-54 Wall-mounted PTZ Bullet Camera Dimensions of base mounted PTZ bullet camera is shown in Figure 2-52. 255 157 129 129 195 4-7 100 Figure 2-55 Base-mounted PTZ Bullet Camera Unit: mm 100 37 Network PTZ CameraQuick Start Guide 2.6.2 Wall Mounting Before you start:

The wall-mounted PTZ bullet camera can be installed on cement wall and pole mounting. The installing environment shall meet the following conditions:

For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps:

1. Drill screw holes on the wall according to the dimensions of wall-mounted camera and insert four M6 expansion screws into the screw holes, as shown in Figure 2-53. Figure 2-56 Drill Screw Holes 2. Route the cables through the camera bracket and cover the four hex nuts with flat washers. 38 Network PTZ CameraQuick Start Guide 3. Fix the camera on the wall by knocking the expansion screws into the wall through the bracket, as shown in Figure 2-54. Figure 2-57 Install the Wall-mounted PTZ Bullet Camera Notes:

To install the PTZ bullet camera with the pole, you can use hexagon socket screws instead of the expansion screws. Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 2.6.3 Base Mounting Before you start:

Base-mounted PTZ bullet camera can be installed on hard plane structures such as cement surface. Note:

Make sure that the plane structure is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps:

39 Network PTZ CameraQuick Start Guide 1. Drill screw holes on the plane surface according to the dimensions of base-mounted camera. 2. Insert four M6 hexagon socket screws (with length of 30 mm) through the camera bracket and the plane structure, and then lock the screw nuts to fix the camera, as shown in Figure 2-55. Figure 2-58 Install Base-mounted Camera Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 2.7 Installing DE4AxxxI Series PTZ Camera DE4AxxxI series (IR) PTZ camera supports ceiling mounting and in-ceiling mounting. Note:

Wall mounting, pendant mounting, and installation with junction box are supported for DE4AxxxI series (IR) PTZ camera. The corresponding accessories shall be purchased separately. 40 Network PTZ CameraQuick Start Guide 2.7.1 Ceiling Mounting Ceiling mounting for DE4AxxxI series (IR) PTZ camera is similar to ceiling mounting for DE2xxx series & DE2xxxI series (IR) PTZ camera. Refer to section 2.4.2 Ceiling Mounting for details. Note:

After DE4AxxxI series (IR) PTZ camera is installed, tighten the fixing screw with a screwdriver as shown in Figure 2-56. Fixing Screw Figure 2-59 Tighten the Fixing Screw 2.7.2 In-ceiling Mounting Notes:

Reserve at least 250 mm of height for in-ceiling mounting. Make sure the ceiling is strong enough to withstand more than The thickness of the ceiling shall range from 5 mm to 40 mm. four times the weight of the PTZ camera and its accessories Steps:

1. Rotate the base plate counterclockwise to separate it from the PTZ camera, as shown in Figure 2-57. 41 Network PTZ CameraQuick Start Guide Rotate Counterclockwise Separate the Base Plate from the PTZ Camera Figure 2-60 Separate the Base Plate from the PTZ camera 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and drill a hole in the ceiling according to the template. 212 Figure 2-61 Drill Template 3. Align the cable holes of the base plate to the cable holes of the in-ceiling bracket and then fix the base plate onto the bracket with the four screws in the package (supplied), as shown in Figure 2-59. 42 Network PTZ CameraQuick Start Guide Figure 2-62 Fix the Base Plate to In-ceiling Bracket 4. Connect the cables and route the cables through the cable hole. Note:

Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 5. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 6. Fix the screws on the side with a screwdriver, as shown in Figure 2-60. Fix the Screw OPEN LOCK 43 Network PTZ CameraQuick Start Guide Figure 2-63 Fix the Camera 7. Place the camera and the bracket into the hole drilled in step 2, and rotate the screws clockwise to fix the camera. 8. Fix the decorative rim with the bubble and the decorative rim will be attached to the in-ceiling bracket automatically, as shown in Figure 2-61. Fix the Screw Fix the Decorative Rim Figure 2-64 Assemble the Decorative Rim 2.8 Installing DE3AxxxI Series PTZ Camera DE3AxxxI series PTZ camera only supports wall mounting. 2.8.1 Wall Mounting Notes:

The camera can be installed on cement wall and wooden wall. The installing environment shall meet the following conditions:

For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. 44 Network PTZ CameraQuick Start Guide For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its cable Steps:

1. Pull the bracket out from the side of the camera, and unclench the decorative cover as shown in Figure 2-65. Decorative cover Bracket Figure 2-65 Open the Decorative cover and pull out bracket 2. The cables can be routed either through the wall or on the wall surface. For the cables routed through the wall, it is required to drill a cable hole on the wall, aligning it with the hole on the bracket, 45 Network PTZ CameraQuick Start Guide and connect cables through the wall and the cable hole on the bracket. For the cables routed on the wall surface, you need to route the cables through the middle slot on the bottom of the back box, as shown in Figure 2-66. Cable slot Figure 2-66 Wiring on the wall 3. Fix the bracket to the target position with four screws (PA425) in the package (supplied), making sure the direction of the sign UP is upward as shown in Figure 2-67. Notes:

For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. 46 Network PTZ CameraQuick Start Guide Figure 2-67 Fix the bracket 4. Fix the camera to the mounting bracket. a. Route the cables. b. Align the camera to the wall mounting bracket, and push camera body until hear a click sound. Tighten the screws under the bracket. c. Figure 2-68 Fix the camera 5. Connect all the cables properly. Note:

47 Network PTZ CameraQuick Start Guide Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 6. Put cables in the back box, then close the decorative cover as shown in Figure 2-69. Back box Figure 2-69 Connect the cables 2.9 Installation of Network Cable Water-proof Jacket Purpose:

If the camera is installed outdoor, you can adapt the water-proof accessory for the network cable after the camera is secured on the installation surface. 48 Network PTZ CameraQuick Start Guide Figure 2-70 Water-proof Accessory Components Table 2-1 Components No. 1 Components Cameras Network Interface Socket 2 3 4 5 6 7 O-Type Gasket Network Plug Waterproof Endcap Waterproof Rubber Gasket Lock Nut Network Cable from Router/Switch Steps:

1. Feed the plugless network cable through the lock nut , waterproof rubber gasket (the rubber gasket inset ridge must face the waterproof endcap), and the waterproof endcap in order. 2. Crimp an RJ-45 network plug onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. 3. Place the O-type gasket onto the end of the cameras network interface socket . 4. Insert the network plug into the cameras network interface socket. 49 Network PTZ CameraQuick Start Guide 5. Insert the waterproof rubber gasket into the waterproof endcap , and secure lock nut with the waterproof endcap

. 6. Align the snap on the waterproof endcap with the notch on the cameras network interface socket , and then secure the waterproof endcap to the cameras network interface socket to finish installation. Align the snap and notch. i. Insert into . ii. Secure with . Camera Switch/Router Figure 2-71 Water-proof Accessory Installation 50 Network PTZ CameraQuick Start Guide 2.10 Installation of Water-proof Tape Purpose:

If the camera is installed outdoor, you can use supplied water-proof tape to protect cable connectors and unused cables after the camera is secured on the installation surface. Steps:

1. Tear off the yellow release paper on the back of the water-proof tape. 2. Stretch the water-proof tape to reach twice the initial length. Initial Length Stretch Stretch Waterproof Tape Length After Stretching Figure 2-72 Stretch the Water-proof Tape 3. Wrap the water-proof tape around the cable connector tightly as the figure below. 51 Network PTZ CameraQuick Start Guide Cable Connector Figure 2-73 Wrap the Water-proof Tape Note:

Make sure that all naked wires are all firmly wrapped in the water-proof tape. 4. Press the tape on both ends of the connector to make sure no water can get in as the figure below. Press s s e r P Press Press Figure 2-74 Press the Water-proof Tape 52 Network PTZ CameraQuick Start Guide 5. Wrap the water-proof tape around the remaining unused cables tightly as the figure below. Figure 2-75 Wrap the Unused Cables Note:

Make sure that all naked wires are all firmly wrapped in the water-proof tape. 6. Press the tape to make sure no water can get in as the figure below. Press Press Press s s e r P Figure 2-76 Press the Water-proof Tape 53 Network PTZ CameraQuick Start Guide 3 Setting the PTZ Camera over the LAN Notes:

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection. If the product does not work properly, contact with your dealer or the nearest service center. To ensure network security of the network PTZ camera, we recommend you to have the camera assessed and maintained termly. You can contact us if you need such service. 3.1 Wiring To view and configure the network PTZ camera via LAN (Local Area Network), you need to connect the network PTZ camera in the same subnet with your PC. Then, install the SADP or client software to search and change the IP address of network PTZ camera. Connect the camera to network according to the following figures. Network Cable Network PTZ Camera Computer Figure 3-1 Connecting Directly 54 Network PTZ CameraQuick Start Guide ork C a ble N et w or Network Cable Network PTZ Camera Computer Figure 3-2 Connecting via a Switch or a Router 3.2 Activating the Camera Purpose:

You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via web browser, activation via SADP, and activation via client software are supported. We will take activation via SADP software and activation via web browser as examples to introduce the camera activation. Note:

For the details of activation via client software, refer to the user manual of the network camera. 3.2.1 Activation via Web Browser Steps:

1. Power on the camera. Connect the camera to your computer or the switch/router which your computer connects to. 2. Input the IP address into the address bar of the web browser, and enter the activation interface. 55 Network PTZ CameraQuick Start Guide Notes:

The default IP address of the camera is 192.168.1.64. The computer and the camera should belong to the same subnet. For the camera enables the DHCP by default, you need to use the SADP software to search the IP address. Figure 3-3 Activation Interface (Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Confirm the password. 5. Click OK to activate the camera and enter the live view interface. 56 Network PTZ CameraQuick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the device, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps:

1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select an inactive device. Select inactive device. Input and confirm password. Figure 3-4 SADP Interface Note:

The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details. 57 Network PTZ CameraQuick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. Note:

You can enable the Hik-Connect service for the device during activation. Refer to section 5.1 Enable Hik-Connect Service on Camera. 4. Click Activate to save the password. Note:

You can check whether the activation is completed on the popup window. If activation failed, make sure that the password meets the requirement and try again. 3.3 Modifying the IP Address Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. 58 Network PTZ CameraQuick Start Guide Use the SADP software or client software to search and change the IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification. Note:

For IP address modification via client software, refer to the user manual of client software. Steps:

1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the Enable DHCP checkbox. 59 Network PTZ CameraQuick Start Guide Figure 3-5 Modify the IP Address Note:

You can enable the Hik-Connect service for the device during activation. Refer to section 5.1 Enable Hik-Connect Service on Camera. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by SADP. Refer to the user manual of SADP for details. 60 Network PTZ CameraQuick Start Guide 4 Accessing via Web Browser System Requirement:

Operating System: Microsoft Windows XP SP1 and above version/Vista/Win7/Server 2003/Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024 768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome 18 and above version Steps:

1. Open the web browser. 2. In the browser address bar, input the IP address of the network PTZ camera, and enter the login interface. Note:

The default IP address is 192.168.1.64. You are recommended to change the IP address to the same subnet with your computer. 3. Input the user name and password. The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions. Note:

The device IP address gets locked if the admin user performs 7 failed password attempts (5 attempts for the user/operator). 61 Network PTZ CameraQuick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the network PTZ camera. Follow the installation prompts to install the plug-in. Note:

You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. 62 Network PTZ CameraQuick Start Guide Note:

For detailed instructions of further configuration, refer to the user manual of the network camera. 63 Network PTZ CameraQuick Start Guide 5 Operating via Hik-Connect App Purpose:

Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note:

Hik-Connect service is not supported by certain camera models. 5.1 Enable Hik-Connect Service on Camera Purpose:

Hik-Connect service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.1 Enable Hik-Connect Service via SADP Software Steps:

1. Check the Enable Hik-Connect checkbox on:

1). "Activate the Device" page during camera activation, refer to section 3.2.2 Activation via SADP Software. 2). Or "Modify Network Parameters" page during modifying IP address, refer to section 3.3 Modifying the IP Address. 2. Create a verification code or change the verification code. 64 Network PTZ CameraQuick Start Guide Figure 5-1 Verification Code Setting (SADP) Note:

The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start:

You need to activate the camera before enabling the service. Refer to section 3.2 Activating the Camera. 65 Network PTZ CameraQuick Start Guide Steps:

1. Access the camera via web browser. Refer to section 4 Accessing via Web Browser. 2. Enter platform access configuration interface:

Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4. Check the Enable checkbox. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6. Create a verification code or change the verification code for the camera. Note:

The verification code is required when you add the camera to Hik-Connect app. 7. Save the settings. 66 Network PTZ CameraQuick Start Guide 5.2 Hik-Connect Setup Steps:

1. Download and install the Hik-Connect app by searching Hik-Connect in App Store or Google PlayTM. 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. 5.3 Adding Camera to Hik-Connect Before you start:

You need to enable the Hik-Connect service on camera before adding it to your Hik-Connect account. Refer to section 5.1 Enable Hik-Connect Service on Camera. Steps:

1. Use a network cable to connect the camera with a router if the camera does not support Wi-Fi. Figure 5-3 Connect a Router Note:

After the camera connects to the network, wait one minute before any operation on the camera using Hik-Connect app. 2. In the Hik-Connect app, tap + on the upper-right corner and then scan the QR code of the camera to add the camera. 67 Network PTZ CameraQuick Start Guide You can find the QR code on the camera or on the cover of the quick start guide of the camera in the package. Figure 5-4 Scan QR Code Note:

If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the camera's serial number. icon and inputting the 3. Input the verification code of your camera. Notes:

The required verification code is the code you create or change when you enabling Hik-Connect service on camera. If you forget the verification code, you can check the current verification code on Platform Access configuration page via web browser. 4. Follow the prompts to set the network connection and add the camera to your Hik-Connect account. Note:

For detailed information, refer to the user manual of the Hik-Connect app. 68 Network PTZ CameraQuick Start Guide 5.4 Initializing the Memory Card Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection. 69 Network PTZ CameraQuick Start Guide This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 70 Network PTZ CameraQuick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 71 Network PTZ CameraQuick Start Guide This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut 72 Network PTZ CameraQuick Start Guide fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. ce matriel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 nonce dans un autre environnement.cette eqipment devrait tre install et exploit avec distance minimale de 20 entre le radiateur et votre corps. 73 Network PTZ CameraQuick Start Guide 74 UD11955B