FCC ID: 2ADTD-K3B801SXRM Swing Barrier

DS-K3B801SX Series Swing Barrier User Manual DS-K3B801SX Series Swing Barrier User Manual Legal Information 2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website ( https://

www.hikvision.com/ ). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product. Trademarks Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners. and other Hikvision's trademarks and logos are the properties of Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED "AS IS" AND "WITH ALL FAULTS AND ERRORS". HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR i DS-K3B801SX Series Swing Barrier User Manual PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for fingerprint device, only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image. As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the effectiveness of your security controls. ii DS-K3B801SX Series Swing Barrier User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE"

and comply therefore with the applicable harmonized European standards listed iii DS-K3B801SX Series Swing Barrier User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info iv DS-K3B801SX Series Swing Barrier User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions:

Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death. Cautions: Follow these precautions to prevent potential injury or material damage. Danger:

of the nation and region. In the use of the product, you must be in strict compliance with the electrical safety regulations The equipment must be connected to an earthed mains socket-outlet. Shock hazard! Disconnect all power sources before maintenance. Do not touch the bare metal contacts of the inlets after the circuit breaker is turned off. indicates hazardous live and the external wiring connected to the terminals requires Electricity still exists. installation by an instructed person. Keep body parts away from fan blades. Disconnect the power source during servicing. Keep body parts away from motors. Disconnect the power source during servicing. To prevent possible hearing damage, do not listen at high volume levels for long periods. All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard. Please make sure that the power has been disconnected before you wire, install or dismantle the device. If the top caps should be open and the device should be powered on for maintenance, make sure:

1. Power off the fan to prevent the operator from getting injured accidentally. 2. Do not touch bare high-voltage components. 3. Make sure the switchs wiring sequence is correct after maintenance. Please make sure that the power has been disconnected before you wire, install or dismantle the device. When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. v DS-K3B801SX Series Swing Barrier User Manual Do not ingest battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions:

The equipment shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the equipment. Ensure correct wiring of the terminals for connection to an AC mains supply. The equipment has been designed, when required, modified for connection to an IT power distribution system.

+ identifies the positive terminal(s) of equipment which is used with, or generates direct current.

+ identifies the negative terminal(s) of equipment which is used with, or generates direct current. No naked flame sources, such as lighted candles, should be placed on the equipment. This equipment is suitable for mounting on concrete or other non-combustible surface only. Install the equipment according to the instructions in this manual. To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions. Stainless steel may be corroded in some circumstances. You need to clean and care the device by using the stainless steel cleaner. It is suggested to clean the device every month. Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger). Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time. Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. vi DS-K3B801SX Series Swing Barrier User Manual Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. Do not stay in the lane when the device is rebooting. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY. The instructions shall require connection of the equipment protective earthing conductor to the installation protective earthing conductor. vii DS-K3B801SX Series Swing Barrier User Manual Available Models Product Name Model Description Swing Barrier DS-K3B801SX-L DS-K3B801SX-M DS-K3B801SX-R Left Pedestal Middle Pedestal Right Pedestal viii DS-K3B801SX Series Swing Barrier User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Introduction ........................................................................................................................... 1 1.2 Main Features ........................................................................................................................ 1 Chapter 2 System Wiring ............................................................................................................ 3 Chapter 3 Installation ................................................................................................................. 6 3.1 Disassemble before Installation ............................................................................................. 6 3.2 Install Pedestals ................................................................................................................... 11 Chapter 4 Disassemble before Maintenance ............................................................................. 14 4.1 Disassemble Front and Back Components ........................................................................... 14 4.2 Disassemble Motor Bottom Cover ....................................................................................... 17 4.3 Disassemble Side Base Cover ............................................................................................... 18 4.4 Disassemble Top Cover ........................................................................................................ 21 Chapter 5 General Wiring ......................................................................................................... 24 5.1 Components Introduction .................................................................................................... 24 5.2 Wiring Electric Supply .......................................................................................................... 26 5.3 Wire Interconnecting Cable ................................................................................................. 27 5.4 Wire Network Switch ........................................................................................................... 28 5.5 Face Recognition Terminal Power Supply Wiring ................................................................. 29 5.6 Terminal Description ............................................................................................................ 30 5.6.1 Main Control Board Terminal Description ................................................................... 30 5.6.2 Sub Control Board Terminal Description ..................................................................... 31 5.6.3 Access Control Board Terminal Description ................................................................ 32 5.6.4 Access Control Board Serial Port ID Description ......................................................... 35 5.6.5 RS-485 Wiring ............................................................................................................. 37 5.6.6 RS-232 Wiring ............................................................................................................. 37 5.6.7 Wiegand Wiring .......................................................................................................... 39 ix DS-K3B801SX Series Swing Barrier User Manual 5.6.8 Barrier Control Wiring ................................................................................................. 39 5.6.9 Alarm Output Wiring ................................................................................................... 41 Chapter 6 Device Settings ......................................................................................................... 42 6.1 Set Study Mode .................................................................................................................... 42 6.2 Pair Keyfob (Optional) .......................................................................................................... 43 6.3 Initialize Device .................................................................................................................... 44 6.4 Switch to RS-485/RS-232 Mode ........................................................................................... 45 6.5 Switch Relay Output Mode (NO/NC) .................................................................................... 46 6.5.1 Barrier Control Relay Output Mode ............................................................................ 46 6.5.2 Alarm Relay Output Mode (NO/NC) ............................................................................ 46 Chapter 7 Activation ................................................................................................................. 48 7.1 Activate via SADP ................................................................................................................. 48 7.2 Activate Device via Client Software ...................................................................................... 49 Chapter 8 Client Software Configuration ................................................................................... 51 8.1 Configuration Flow of Client Software ................................................................................. 51 8.2 Device Management ............................................................................................................ 51 8.2.1 Add Device .................................................................................................................. 52 8.2.2 Reset Device Password ................................................................................................ 59 8.3 Group Management ............................................................................................................. 60 8.3.1 Add Group ................................................................................................................... 60 8.3.2 Import Resources to Group ......................................................................................... 60 8.3.3 Edit Resource Parameters ........................................................................................... 61 8.3.4 Remove Resources from Group .................................................................................. 61 8.4 Person Management ............................................................................................................ 62 8.4.1 Add Organization ........................................................................................................ 62 8.4.2 Configure Basic Information ....................................................................................... 62 8.4.3 Issue a Card by Local Mode ......................................................................................... 63 8.4.4 Upload a Face Photo from Local PC ............................................................................ 65 x DS-K3B801SX Series Swing Barrier User Manual 8.4.5 Take a Photo via Client ................................................................................................ 66 8.4.6 Collect Face via Access Control Device ....................................................................... 67 8.4.7 Collect Fingerprint via Client ....................................................................................... 68 8.4.8 Collect Fingerprint via Access Control Device ............................................................. 69 8.4.9 Configure Access Control Information ........................................................................ 70 8.4.10 Customize Person Information .................................................................................. 71 8.4.11 Configure Resident Information ................................................................................ 72 8.4.12 Configure Additional Information ............................................................................. 72 8.4.13 Import and Export Person Identify Information ........................................................ 73 8.4.14 Import Person Information ....................................................................................... 73 8.4.15 Import Person Pictures ............................................................................................. 74 8.4.16 Export Person Information ........................................................................................ 74 8.4.17 Export Person Pictures .............................................................................................. 75 8.4.18 Get Person Information from Access Control Device ................................................ 75 8.4.19 Move Persons to Another Organization .................................................................... 76 8.4.20 Issue Cards to Persons in Batch ................................................................................. 76 8.4.21 Report Card Loss ....................................................................................................... 77 8.4.22 Set Card Issuing Parameters ...................................................................................... 77 8.5 Configure Schedule and Template ....................................................................................... 78 8.5.1 Add Holiday ................................................................................................................. 78 8.5.2 Add Template .............................................................................................................. 79 8.6 Set Access Group to Assign Access Authorization to Persons .............................................. 81 8.7 Configure Advanced Functions ............................................................................................ 83 8.7.1 Configure Device Parameters ...................................................................................... 83 8.7.2 Configure Remaining Open/Closed ............................................................................. 89 8.7.3 Configure Multi-Factor Authentication ....................................................................... 90 8.7.4 Configure Custom Wiegand Rule ................................................................................ 92 8.7.5 Configure Card Reader Authentication Mode and Schedule ...................................... 93 xi DS-K3B801SX Series Swing Barrier User Manual 8.7.6 Configure First Person In ............................................................................................. 95 8.7.7 Configure Anti-Passback ............................................................................................. 96 8.7.8 Configure Device Parameters ...................................................................................... 97 8.8 Configure Linkage Actions for Access Control ...................................................................... 98 8.8.1 Configure Client Actions for Access Event ................................................................... 98 8.8.2 Configure Device Actions for Access Event ................................................................. 99 8.8.3 Configure Device Actions for Card Swiping ............................................................... 100 8.9 Door Control ...................................................................................................................... 101 8.9.1 Control Door Status ................................................................................................... 102 8.9.2 Check Real-Time Access Records .............................................................................. 103 8.10 Event Center .................................................................................................................... 104 8.10.1 Enable Receiving Event from Devices ..................................................................... 105 8.10.2 View Real-Time Events ............................................................................................ 105 8.10.3 Search Historical Events .......................................................................................... 107 8.11 Remote Configuration via Client Software ....................................................................... 110 8.11.1 Check Device Information ....................................................................................... 110 8.11.2 Edit Device Name .................................................................................................... 110 8.11.3 Edit Time ................................................................................................................. 110 8.11.4 Set System Maintenance ......................................................................................... 111 8.11.5 Manage Network User ............................................................................................ 111 8.11.6 Manage Keyfob User ............................................................................................... 112 8.11.7 Set Security ............................................................................................................. 112 8.11.8 Configure Lane Parameters ..................................................................................... 113 8.11.9 Configure Screen Parameters .................................................................................. 113 8.11.10 Configure Screen Parameters ................................................................................ 114 8.11.11 Configure Advanced Network ............................................................................... 115 8.11.12 Configure Audio File .............................................................................................. 115 8.11.13 View Relay Status .................................................................................................. 116 xii DS-K3B801SX Series Swing Barrier User Manual Appendix A. Tips for Scanning Fingerprint ............................................................................... 117 Appendix B. DIP Switch ........................................................................................................... 119 B.1 DIP Switch Description ....................................................................................................... 119 B.2 DIP Switch Corresponded Functions .................................................................................. 119 Appendix C. Event and Alarm Type ......................................................................................... 122 Appendix D. Table of Audio Index Related Content ................................................................. 123 Appendix E. Error Code Description ........................................................................................ 124 Appendix F. Communication Matrix and Device Command ..................................................... 126 xiii DS-K3B801SX Series Swing Barrier User Manual Chapter 1 Overview 1.1 Introduction The swing barrier with two barriers and 24 IR lights is designed to detect unauthorized entrance or exit. By adopting the swing barrier integrated with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc. It is widely used in attractions, stadiums, construction sites, residences, etc. 1.2 Main Features 32-bit high-speed processor TCP/IP network communication Permissions validation and anti-tailgating Remaining open/closed mode selectable Bidirectional (Entering/Exiting) lane The communication data is specially encrypted to relieve the concern of privacy leak. The barrier opening and closing speed can be configured according to the visitor flow. The barrier will be locked or stop working when people are nipped 1 DS-K3B801SX Series Swing Barrier User Manual Anti-forced-accessing The barrier will be locked automatically without open-barrier signal. Self-detection, Self-diagnostics, and automatic alarm Audible and visual alarm will be triggered when detecting intrusion, tailgating, reverse passing, and climbing over barrier IP conflict detection Remote control and management Online/offline operation LED indicates the entrance/exit and light bar indicates passing status Barrier remains open when powered down Fire alarm passing When the fire alarm is triggered, the barrier will be open automatically for emergency evacuation Valid passing duration settings System will cancel the passing permission if a person does not pass through the lane within the valid passing duration Opens/Closes barrier according to the schedule template 2 DS-K3B801SX Series Swing Barrier User Manual Chapter 2 System Wiring The preparation before installation and wiring. Steps 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals. The distance between the nearest two line is L+100 mm. L represents the lane width. 3. Slotting on the installation surface and dig installation holes according to the hole position Note diagram. Figure 2-1 Hole Position Diagram 3 DS-K3B801SX Series Swing Barrier User Manual 4. Bury cables. Each lane buries 1 network cable and 1 high voltage cable. For details, see the system wiring diagram below. Figure 2-2 System Wiring Diagram (General Wiring) Note The supplied interconnecting cable length is 5.5 m. The suggested inner diameter of the low voltage conduit is larger than 30 mm. If you want to bury both of the AC power cord and the low voltage cable at the entrance, the two cables should be in separated conduits to avoid interference. If more peripherals are required to connect, you should increase the conduit diameter or bury another conduit for the external cables. The external AC power cord should be double-insulated. The network cable must be CAT5e or the network cable has better performance. And the suggested network cable length should be less than 100 m. 4 DS-K3B801SX Series Swing Barrier User Manual Figure 2-3 Wire Face Recognition Terminal Note The supplied interconnecting cable length is 5.5 m. The left pedestal and the middle pedestal should bury interconnecting cables for connecting the face recognition terminal. The face recognition terminal installed on the left pedestal will gain power from the 12 V power supply, which should connect to the electric supply. The suggested inner diameter of the low voltage conduit is larger than 30 mm. If you want to bury both of the AC power cord and the low voltage cable at the entrance, the two cables should be in separated conduits to avoid interference. If more peripherals are required to connect, you should increase the conduit diameter or bury another conduit for the external cables. The external AC power cord should be double-insulated. The network cable must be CAT5e or the network cable has better performance. And the suggested network cable length should be less than 100 m. 5 DS-K3B801SX Series Swing Barrier User Manual Chapter 3 Installation 3.1 Disassemble before Installation Before installation, you should disassemble the pedestal and remove some screws. Before You Start Keep the disassembled components and screws. You should prepare the following tools to disassemble the pedestal: 1. Pedestal Key (supplied); 2. Allen Wrench (2.5 mm); 3. Allen Wrench (3 mm); 4. Allen Wrench (4 mm). Steps 1. Use the pedestal key to open the front and back components. 2. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 25) at the top of the device. Figure 3-1 Lock Position 6 DS-K3B801SX Series Swing Barrier User Manual Figure 3-2 M525 Screws 3. Remove the components along the arrow direction carefully. Figure 3-3 Remove Components 4. Loosen the wing bolt (M4 10) at the front and back of the pedestal, and remove the front and back base covers along the arrow direction. 7 DS-K3B801SX Series Swing Barrier User Manual Figure 3-4 Loosen Wing Bolt Figure 3-5 Remove Base Cover You can start installing the expansion screws to secure the device on the installation surface. 5. Remove the motor bottom cover. 1) Pull or push the barrier to the closed position. 2) Use the Allen wretch (2.5 mm) to loosen the 4 screws (M4 8) on the motor bottom cover. 8 DS-K3B801SX Series Swing Barrier User Manual 3) Pull or push the barrier to the open position, and remove the motor bottom cover. Figure 3-6 M48 Screw 9 DS-K3B801SX Series Swing Barrier User Manual Figure 3-7 Remove Motor Bottom Cover Note If dissembling the middle pedestal, you should dissemble two motor bottom covers. 6. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 12) at the front or back of the pedestal base and remove the side base cover slowly. Figure 3-8 Remove Side Base Cover 10 DS-K3B801SX Series Swing Barrier User Manual Note If dissembling the middle pedestal, you should dissemble two side base covers. 7. Disassemble the two protective sheets at the bottom for wiring, and you can start wiring the interconnecting cable. Figure 3-9 Disassemble Two Protective Sheets Before You Start Prepare for the installation tools, check the device and the accessories, and clear the installation base. 3.2 Install Pedestals Steps Note The device should be installed on the concrete surface or other non-flammable surfaces. The dimension is as follows. 1. Prepare for the installation tools, check the components, and prepare for the installation base. Figure 3-10 Dimension 11 DS-K3B801SX Series Swing Barrier User Manual 2. Drill holes on the ground according to the installation holes on the pedestals and insert the 3. According to the entrance and exit marks on the pedestals, move the pedestals to the expansion sleeves. corresponded positions. Make sure the installation holes on the pedestals and the base are aligned with each other. 4. Secure the pedestals with expansion bolts. Note Note Do not immerse the pedestal in the water. In special circumstances, the immersed height should be no more than 150 mm. The installation footprint is as follows:

Figure 3-11 Installation Footprint 12 DS-K3B801SX Series Swing Barrier User Manual 5. After installation, assemble the components and screws back to the pedestal in reverse order

(except for protective sheets). 13 DS-K3B801SX Series Swing Barrier User Manual Chapter 4 Disassemble before Maintenance Before maintaining the inner components, you should disassemble the pedestal and remove some screws. Note Keep the disassembled components and screws organized. You should prepare the following tools to disassemble the pedestal: 1. Pedestal Key (supplied); 2. Allen Wrench (2.5 mm); 3. Allen Wrench (3 mm); 4. Allen Wrench (4 mm). 4.1 Disassemble Front and Back Components After disassembling the front and back components, you can maintain the front and back parts of the pedestal. Steps 1. Use the pedestal key to open the front and back components. 14 DS-K3B801SX Series Swing Barrier User Manual 2. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 25) at the top of the device Figure 4-1 Lock Position 15 DS-K3B801SX Series Swing Barrier User Manual 3. Remove the components along the arrow direction carefully. Figure 4-2 M525 Screws Position Figure 4-3 Remove Components 16 DS-K3B801SX Series Swing Barrier User Manual 4.2 Disassemble Motor Bottom Cover After disassembling the motor bottom cover, you can maintain the lane control board and the barrier position control board. Steps 1. Pull or push the barrier to the closed position. 2. Use the Allen wretch (2.5 mm) to loosen the 4 screws (M4 8) on the motor bottom cover. 3. Pull or push the barrier to the open position, and remove the motor bottom cover. Figure 4-4 M48 Screws Position 17 DS-K3B801SX Series Swing Barrier User Manual Figure 4-5 Remove Bottom Cover Note If dissembling the middle pedestal, you should dissemble two motor bottom covers. 4.3 Disassemble Side Base Cover After disassembling the side base cover, you can maintain the IR sending/receiving board. Steps 1. Use the pedestal key to open the front and back components. 18 DS-K3B801SX Series Swing Barrier User Manual 2. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 25) at the top of the device. Figure 4-6 Lock Position 19 DS-K3B801SX Series Swing Barrier User Manual 3. Remove the components along the arrow direction carefully. Figure 4-7 M525 Screws Position 4. Use the Allen wretch (4 mm) to loosen the 2 screws (M5 12) at the front or back of the pedestal base and remove the side base cover slowly. Figure 4-8 Remove Components 20 DS-K3B801SX Series Swing Barrier User Manual Figure 4-9 Remove Side Base Cover Note If dissembling the middle pedestal, you should dissemble two side base covers. 4.4 Disassemble Top Cover After disassembling the top cover, you can maintain the components at the top of the pedestal, the IR sending/receiving board and the IR adaptor for instance. Steps 1. Use the Allen wretch (2.5 mm) to loosen the 4 captive panel screws at the top of the pedestal. Figure 4-10 Loosen Captive Panel Screw 2. Move the front and back top covers along the arrow 1's direction for about 3 cm, and move them upwards to remove the front and back top covers. 21 DS-K3B801SX Series Swing Barrier User Manual Figure 4-11 Remove Front and Back Top Cover 3. Optional: If you should install the fingerprint modules in the pedestal, you should use the key to open and remove the front and back components, and cut off the fingerprint modules' power. 4. Use the Allen wrench (2.5 mm) to loosen the 2 captive panel screws displayed in the picture below. 5. Remove the top cover along the arrow's direction. Figure 4-12 Top Captive Panel Screws 22 DS-K3B801SX Series Swing Barrier User Manual Figure 4-13 Remove Top Cover 23 DS-K3B801SX Series Swing Barrier User Manual Chapter 5 General Wiring 5.1 Components Introduction By default, basic components of the turnstile are connected well. The pedestals can communicate by wiring the interconnecting cables. And the turnstile supports wiring the AC electric supply for the whole systems power supply. The voltage fluctuation of the electric supply is between 100 VAC and 220 VAC, 50 to 60 Hz. The picture displayed below describes each component's position on the turnstile. Note Note The diagram is for reference only. 24 DS-K3B801SX Series Swing Barrier User Manual Figure 5-1 Components Diagram The picture displayed below describes the IR sending/receiving module and their corresponding number on the pedestal. 25 DS-K3B801SX Series Swing Barrier User Manual Figure 5-2 IR Sending/Receiving Module Position Note If the turnstile contains two lanes, standing at the entrance position, the IR modules on the left pedestal are the IR sending modules. The IR modules on the right pedestal are the IR receiving modules. The IR modules on the left side of the middle pedestal are the IR receiving modules, while the IR modules on the right side of the middle pedestal are the IR sending modules. 5.2 Wiring Electric Supply Wire electric supply with the switch in the pedestal. Terminal L and terminal N are on the switch, while terminal PE should connect to a ground wire (yellow and green wire). 26 DS-K3B801SX Series Swing Barrier User Manual Note The cable bare part should be no more than 8 mm. It is suggested that you can immerse the bare part into the liquid tin. If possible, wear an insulation cap at the end of the bare cable. Make sure theres no bare copper or cable after the wiring. The Terminal L and the Terminal N cannot be wired reversely. Do not wire the input and output terminal reversely. To avoid people injury and device damage, when testing, the ground resistance of the equipotential points should not be larger than 2 5.3 Wire Interconnecting Cable You should use interconnecting cables to connect the main lane board and the sub lane board for components communication. The picture displayed below describes the cable hole's position on the pedestals. 27 DS-K3B801SX Series Swing Barrier User Manual Follow the instructions below to connect the interconnecting cable. Figure 5-3 Cable Hole of Interconnecting Cable Figure 5-4 Connect Interconnecting Cable 5.4 Wire Network Switch Connect the network cable and the network switch. Steps 1. Open the side cover of the pedestal. 28 DS-K3B801SX Series Swing Barrier User Manual Note For details, see Disassemble Side Base Cover . Figure 5-5 Network Switch Position 2. Lead out 12 V power supply from the main switch and connect it to the network switch's power interface. 3. Connect the network cable with the network switch. 5.5 Face Recognition Terminal Power Supply Wiring You should wire the power supply terminal on the 12 V power supply component if you connect the turnstile to the face recognition terminal. The terminal's position is shown as follows:

29 DS-K3B801SX Series Swing Barrier User Manual Figure 5-6 Face Recognition Terminal Power Supply Wiring Position 5.6 Terminal Description The lane controller contains main lane controller and sub lane controller, which controls the IR beams, motor, and other components' work. 5.6.1 Main Control Board Terminal Description The main lane control board contains power supply interface, supercapacitor interface, brake interface, motor drive interface, light board interface, motor encoder interface, door open position detection interface, debug port, lane communication interface, interconnecting interface, and DIP switch (reserved). The picture displayed below is the main control board diagram. 30 DS-K3B801SX Series Swing Barrier User Manual Figure 5-7 Main Control Board 5.6.2 Sub Control Board Terminal Description The sub lane control board contains power supply interface, supercapacitor interface, brake interface, motor drive interface, light board interface, motor encoder interface, door open position detection interface, debug port, lane communication interface, and interconnecting interface. The picture displayed below is the sub control board diagram. Figure 5-8 Sub Control Board 31 DS-K3B801SX Series Swing Barrier User Manual 5.6.3 Access Control Board Terminal Description Figure 5-9 Access Control Board Table 5-1 Access Control Board Terminal Description Access Control Board Terminal Description Power Output 1

+12 V Power Output Grounding Wiegand Card Reader 1 GND OK ERR BZ W1 W0 GND OK ERR BZ W1 W0 Wiegand Card Reader 2 Indicator of Card Reader Control Output (Invalid Card Output) Indicator of Card Reader Control Output (Valid Card Output) Card Reader Buzzer Control Output Wiegand Head Read Data Input Data1 Wiegand Head Read Data Input Data0 Grounding Indicator of Card Reader Control Output (Invalid Card Output) Indicator of Card Reader Control Output (Valid Card Output) Card Reader Buzzer Control Output Wiegand Head Read Data Input Data1 Wiegand Head Read Data Input Data0 32 DS-K3B801SX Series Swing Barrier User Manual Access Control Board Terminal Description RS-485 Interface Power Output 2 RS-232 Interface Power Input Event Input Exit Button GND GND RS-485 B-

RS-485 B+

GND RS-485 C-

RS-485 C+

5 V GND GND RS-232 G-

RS-232 G+

GND RS-232 H-

RS-232 H+

+24 V GND C1 GND C2 C3 C4 B2 GND GND B1 D1-

D1+

D2-

Grounding Grounding Grounding Connect to Card Reader RS485-

Connect to Card Reader RS485+

Connect to Card Reader RS485-

Connect to Card Reader RS485+

5 VDC Power Output 5 VDC Grounding Grounding Connect to Card Reader RS232-

Connect to Card Reader RS232+

Grounding Connect to Card Reader RS232-

Connect to Card Reader RS232+

24 VDC Power Input Grounding Event Alarm Input 4 Grounding Fire Input Event Alarm Input 2 Grounding Event Alarm Input 1 Door 2 Signal Input Grounding Door 1 Signal Input Door 2 Relay Output (Dry Contact) 33 Door Lock (Relay) Door 1 Relay Output (Dry Contact) DS-K3B801SX Series Swing Barrier User Manual Access Control Board Terminal Description Alarm Output Alarm Output Relay 1 (Dry Contact) D2+

NO/NC1 COM1 NO/NC2 COM2 NO/NC3 COM3 NO/NC4 COM4 Alarm Output Relay 2 (Dry Contact) Alarm Output Relay 3 (Dry Contact) Alarm Output Relay 4 (Dry Contact) Network Interface LAN Network Accessing Note The alarm input hardware interface is normally open by default. So only the normally open signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the alarm relay output and open door relay output. The DIP of RS-485 card ID is set as 1 and 4 by default. 1 is for entering, and 4 is for exiting. If the user has configured visitor card, you should connect two card readers on the exiting side. Set the DIP switch of one of the card reader as 4, and set the other one's as 3. Card Reader 3 should be used together with the card recycler. Normal users should present card on Card Reader 4, while visitors should present card on Card Reader 3. The Wiegand card reader 1 and 2 refer to the entering and exiting card reader respectively. The alarm output supports relay output. For any requirements, the door lock can control the door barrier status of the third party. D1 controls the barrier opening for entrance, while D2 controls the door opening for exit. For details, see Barrier Control Relay Output Mode . C3 and C4 in the event input can also be people counting interface. C3 controls people counting for entrance, while C4 controls people counting for exit. When the access control board detects signals in C3 and C4, the people number will be accumulated. For detailed information about people counting and people number, see Configuring People Counting Parameters in User Manual of iVMS-4200 AC Client Software. For detailed information about the DIP switch, see DIP Switch . 34 DS-K3B801SX Series Swing Barrier User Manual 5.6.4 Access Control Board Serial Port ID Description You can use the jumper cap on the access control board to switch the interface communication mode. For details about switching between RS-232 and RS-485 communication type, see Switching RS-485/RS-232 Mode. Figure 5-10 Access Control Board According to the picture above, the RS-485 serial port corresponds to UART2 and UART3. RS-232 serial port is corresponded to UART7 and UART8. Wiring Interface is corresponded to UART1, UART4, UART6, UART6, and Lane. The access control board descriptions are as follows:

UART2/UART3 Jumper Cap Reserved serial port. Use the jumper cap to switch the serial port communication mode. You can switch between the RS-485 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode. UART6 Jumper Cap UART5 Jumper Cap UART1 Jumper Cap Lane Use the jumper cap to switch the serial port communication mode with the sub lane controller. You can switch between the RS-232 communication mode and the RS-485 communication mode. By default, it is in RS-232 communication mode. Use the jumper cap to switch the serial port communication mode with the sub lane controller. You can switch between the RS-485 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode. Use the jumper cap to switch the serial port communication mode with the main lane controller. You can switch between the RS-485 communication mode and the RS-232 communication mode. By default, it is in RS-485 communication mode. 35 DS-K3B801SX Series Swing Barrier User Manual Use the jumper cap to switch the serial port communication mode with the lane controller. By default, the interface is wired and it is in RS-485 communication mode. If wiring other controllers (compatible with Hikvision communication protocol), use the jumper cap to switch between RS-485 and RS-232 communication mode. The serial port is in the wiring interface according to the picture above, which has a fixed RS-232 communication mode to communicate with the main lane controller. It contains no jumper cap and cannot change the communication mode. UART4 UART7/UART8 Reserved serial port. The serial port has a fixed RS-232 communication mode. It contains no jumper cap and cannot change the communication mode, which can connect with a QR code scanner. The reserved interface positions in the turnstile and their corresponded UART No. are as follows:

Note The diagram is for reference only. Figure 5-11 Interface and Corresponded UART No. 36 DS-K3B801SX Series Swing Barrier User Manual 5.6.5 RS-485 Wiring There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR code scanner, fingerprint and card reader, card recycler, text screen, fingerprint reader, and face recognition terminal. Take the wiring of RS-485 card reader as an example. For details about text screen, see Configuring Screen Parameters in User Manual of iVMS-4200 Note Note AC Client Software. 5.6.6 RS-232 Wiring There are three RS-232 interfaces (UART4, UART7, and UART8). UART7 and UART8 can connect QR code scanner, and card recycler, while UART4 can connect QR code scanner, card recycler, and face recognition terminal. 37 DS-K3B801SX Series Swing Barrier User Manual 38 DS-K3B801SX Series Swing Barrier User Manual 5.6.7 Wiegand Wiring Note Note Connect the OK/ERR/BZ if the access controller should control the LED and buzzer of the Wiegand card reader. 5.6.8 Barrier Control Wiring By default, the barrier has connected with the access control board. The lane control board can control the barrier status. If possible, the device can connect with a third party lane control board to control the third party barriers. Interface D1 controls barrier opening for entrance, while interface D2 controls barrier opening for exit. Use the jumper cap to switch the relay status. For details, see Barrier Control Relay Output Mode . 39 DS-K3B801SX Series Swing Barrier User Manual Entering Wiring Exiting Wiring 40 DS-K3B801SX Series Swing Barrier User Manual 5.6.9 Alarm Output Wiring Note For details about changing the relay output status via the jumper cap, see Alarm Relay Output Mode (NO/NC) . 41 DS-K3B801SX Series Swing Barrier User Manual Chapter 6 Device Settings After installation and wiring completed, you should set the barriers closed position (study mode) before entering the working mode. You can also set the test mode, normal mode, passing mode and memory mode, pair the keyfob, initialize the hardware, switching between RS-485 communication mode and RS-232 communication mode, and view relay output NO/NC diagram by setting the DIP switch on the access control board. Study Mode: The barrier will learn the closed position. Normal Mode: The device will work properly. Test Mode: Test mode is the same as the normal mode except that the device cannot report the alarm, the event, or the people counting information to the center. Passing Mode: There are 9 passing modes, including controlled bi-direction, controlled entrance and prohibited exit, controlled entrance and free exit, free bi-direction, free entrance and controlled exit, free entrance and prohibited exit, prohibited bi-direction, prohibited entrance and free exit. Memory Mode: By default, the memory mode is enabled. When multiple cards are presented and authenticated, it allows multiple persons passing through the lane. When it counts the passing people number is equal to the card presented times, or no person passing through the lane after the last person passing, the barriers will be closed. Note You can also set the DIP switch on the access control board to control the entrance and exit controlling type, keyfob pairing, etc. For details about the DIP switch value, see DIP Switch . 6.1 Set Study Mode Enter the study mode through DIP switching to set the closed position of the device barrier. Steps 1. Set The No.1 of the 8-digit DIP Switch on the main control board to ON by referring the following figure to enter the study mode. 2. Adjust the closed position of the barrier. 3. Power on the device. The device will remember the current position (closed position) automatically. 4. Power off the device. 42 DS-K3B801SX Series Swing Barrier User Manual 5. Set the No.1 switches of the 8-digit DIP Switch on the main control board by referring to the following figure. 6. Power on the device again. Note For details about the DIP switch value and meaning, see DIP Switch Description. The barrier will open automatically and turns back to the closed position. At this circumstance, the device enters the normal mode. 6.2 Pair Keyfob (Optional) Pair the remote control to the device through DIP switch to open/close the barrier remotely. Before You Start Ask our technique supports or sales and purchase the keyfob. Steps Note Up to 32 keyfobs can be added to the turnstile. 1. Power off the turnstile. 2. Set the No.4 switch of the DIP Switch on the access control board to the ON side. 3. Power on the turnstile and it will enter the keyfob pairing mode. 4. Hold the Close button for more than 10 seconds. Or pair turnstile and keyfob in the client software, see Manage Keyfob User for more details. The keyfob's indicator of the will flash twice if the pairing is completed. 5. Set the No.4 switch to OFF, and reboot the turnstile to take effect. 43 DS-K3B801SX Series Swing Barrier User Manual Note Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the keyfob will select only one of them to pair. For details about DIP switch value and meaning, see DIP Switch . 6. Optional: Go to System User Keyfob User on the remote control page of the client software to delete the keyfob. 6.3 Initialize Device Steps 1. Remove the JP11 jumper cap on the access control board. Figure 6-1 Initialization Jumper Cap 2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep. 3. When the beep stopped, plug the jumper cap back. 4. Disconnect the power and power on the device again. Caution Note The initialization of the device will restore all the parameters to the default setting and all the device events are deleted. Make sure no persons are in the lane when powering on the device. 44 DS-K3B801SX Series Swing Barrier User Manual 6.4 Switch to RS-485/RS-232 Mode Take the Serial Port 4 and on the access control board as an example. If the Jumper cap's position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-485 communication mode. Figure 6-2 Jumper Cap Status of RS-485 Interface If the Jumper cap's position is like the picture displayed below. (The black part is the jumper cap.) The serial port is in RS-232 communication mode. Figure 6-3 Jumper Cap Status of RS-232 Interface 45 DS-K3B801SX Series Swing Barrier User Manual 6.5 Switch Relay Output Mode (NO/NC) 6.5.1 Barrier Control Relay Output Mode The pins of the barrier control relay on the access control board is as below:

The jumper cap's position of barrier opening for entrance (NO) is as below:

Figure 6-4 Pin Appearance The jumper cap's position of barrier opening for exit (NO) is as below:

The jumper cap's position of barrier closing for entrance (NC) is as below:

The jumper cap's position of barrier closing for exit (NC) is as below:

6.5.2 Alarm Relay Output Mode (NO/NC) Alarm Relay Output Mode (NO):

46 DS-K3B801SX Series Swing Barrier User Manual Alarm Relay Output Mode (NC):

47 DS-K3B801SX Series Swing Barrier User Manual Chapter 7 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows:

The default IP address: 192.0.0.64 The default port No.: 8000 The default user name: admin 7.1 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start Get the SADP software from the supplied disk or the official website http://

www.hikvision.com/en/ , and install the SADP according to the prompts. The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address. For batch activation and IP addresses modification, refer to User Manual of SADP for details. Steps 1. Run the SADP software and search the online devices. 2. Find and select your device in online device list. 3. Input new password (admin password) and confirm the password. Caution STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click Activate to start activation. 48 DS-K3B801SX Series Swing Barrier User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 7.2 Activate Device via Client Software For some devices, you are required to create the password to activate them before they can be added to the software and work properly. Steps Note This function should be supported by the device. on the right of Device Management and select Device. 1. Enter the Device Management page. 2. Click 3. Click Online Device to show the online device area. The searched online devices are displayed in the list. 4. Check the device status (shown on Security Level column) and select an inactive device. 5. Click Activate to open the Activation dialog. 6. Create a password in the password field, and confirm the password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least 49 DS-K3B801SX Series Swing Barrier User Manual three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 7. Click OK to activate the device. 50 DS-K3B801SX Series Swing Barrier User Manual Chapter 8 Client Software Configuration 8.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 8-1 Flow Diagram of Configuration on Client Software 8.2 Device Management The client supports managing access control devices and video intercom devices. Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 51 DS-K3B801SX Series Swing Barrier User Manual The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. 8.2.1 Add Device Add Online Device The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click Refresh Every 60s to refresh the information of the online devices. Add Single or Multiple Online Devices The client can detect online devices which are in the same network as the PC running the client. You can select a detected online device displayed in the online device list and add it to the client. For detected online devices sharing the same user name and password, you can add them to the client in a batch. Before You Start The device(s) to be added are in the same network as the PC running the client. The device(s) to be added have been activated. Steps 1. Click Device Management Device 2. Click Online Device to show the online device area. The searched online devices are displayed in the list. Figure 8-2 Online Device 3. In the Online Device area, check one or more online device(s), and click Add to open the device adding window. 52 DS-K3B801SX Series Swing Barrier User Manual Figure 8-3 Add Single Online Device 4. Enter the required information. Figure 8-4 Add Multiple Online Devices Enter a descriptive name for the device. Enter the device's IP address. The IP address of the device is obtained automatically in this adding mode. You can customize the port number. The port number of the device is obtained automatically in this adding mode. Name IP Address Port User Name 53 DS-K3B801SX Series Swing Barrier User Manual By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 5. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS

(Transport Layer Security) protocol for security purpose. Note This function should be supported by the device. If you have enabled Certificate Verification, you should click Open Certificate Directory to open the default folder, and copy the certificate file exported from the device to this default directory to strengthen the security. See for details about enabling certificate verification. You can log into the device to get the certificate file by web browser. 6. Check Synchronize Time to synchronize the device time with the PC running the client after 7. Optional: Check Import to Group to create a group by the device name, and import all the adding the device to the client. channels of the device to this group. Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 8. Click Add. Add Multiple Detected Online Devices For detected online devices sharing the same user name and password, you can add them to the client in a batch. Before You Start Make sure the to-be-added devices are online. Steps 1. Enter the Device Management module. 54 DS-K3B801SX Series Swing Barrier User Manual 2. Click Device tab on the top of the right panel. 3. Click Online Device to show the online device area at the bottom of the page. The searched online devices are displayed in the list. 4. Select multiple devices. Note For the inactive device, you need to create the password for it before you can add the device properly. For details, refer to . 5. Click Add to open the device adding window. 6. Enter the required information. User Name Password By default, the user name is admin. Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 7. Optional: Check Synchronize Time to synchronize the device time with the PC running the client 8. Optional: Check Import to Group to create a group by the device name, and import all the after adding the device to the client. channels of the device to this group. Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 9. Click Add to add the devices. Add Device by IP Address or Domain Name If you know the IP address or domain name of the device to add, you can add devices to the client by specifying the IP address (or domain name), user name, password, etc. Steps 1. Enter Device Management module. 55 DS-K3B801SX Series Swing Barrier User Manual 2. Click Device tab on the top of the right panel. The added devices are displayed on the right panel. 3. Click Add to open the Add window, and then select IP/Domain as the adding mode. 4. Enter the required information. Create a descriptive name for the device. For example, you can use a nickname that can show the location or feature of the device. The IP address or domain name of the device. The devices to add share the same port number. The default value is 8000. Enter the device user name. By default, the user name is admin. Name Address Port User Name Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 5. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS

(Transport Layer Security) protocol for security purpose. Note This function should be supported by the device. If you have enabled Certificate Verification, you should click Open Certificate Directory to open the default folder, and copy the certificate file exported from the device to this default directory to strengthen the security. See for details about enabling certificate verification. You can log into the device to get the certificate file by web browser. 6. Check Synchronize Time to synchronize the device time with the PC running the client after 7. Optional: Check Import to Group to create a group by the device name, and import all the adding the device to the client. channels of the device to this group. 56 DS-K3B801SX Series Swing Barrier User Manual Example For access control device, its access points, alarm inputs/outputs, and encoding channels (if exist) will be imported to this group. 8. Finish adding the device.

- Click Add to add the device and back to the device list page.

- Click Add and New to save the settings and continue to add other device. Add Devices by IP Segment If the devices share the same port No., user name and password, and their IP addresses ranges in the same IP segment, you can add them to the client by specifying the start IP address and the end IP address, port No., user name, password, etc of the devices. Steps 1. Enter the Device Management module. 2. Click Device tab on the top of the right panel. The added devices are displayed on the right panel. 3. Click Add to open the Add window. 4. Select IP Segment as the adding mode. 5. Enter the required information. Enter a start IP address. Start IP End IP Port User Name Password By default, the user name is admin. Enter the device password. Caution Enter an end IP address in the same network segment with the start IP. Enter the device port No. The default value is 8000. The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. 57 DS-K3B801SX Series Swing Barrier User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 6. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS

(Transport Layer Security) protocol for security purpose . Note This function should be supported by the device. If you have enabled Certificate Verification, you should click Open Certificate Folder to open the default folder, and copy the certificate file exported from the device to this default directory to strengthen the security. See for details about enabling certificate verification. You can log into the device to get the certificate file by web browser. 7. Check Synchronize Time to synchronize the device time with the PC running the client after 8. Optional: Check Import to Group to create a group by the device name, and import all the adding the device to the client. channels of the device to the group. 9. Finish adding the device.

- Click Add to add the device and back to the device list page.

- Click Add and New to save the settings and continue to add other device. Import Devices in a Batch You can add multiple devices to the client in a batch by entering the device parameters in a pre-

defined CSV file. Steps 1. Enter the Device Management module. 2. Click Device tab on the top of the right panel. 3. Click Add to open the Add window, and then select Batch Import as the adding mode. 4. Click Export Template and then save the pre-defined template (CSV file) on your PC. 5. Open the exported template file and enter the required information of the devices to be added For detailed description of the required fields, refer to the introductions in the template. on the corresponding column. Note Adding Mode Enter 0 or 1 or 2. Address Port Edit the address of the device. Enter the device port number. The default port number is 8000. 58 DS-K3B801SX Series Swing Barrier User Manual Enter the device user name. By default, the user name is admin. User Name Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Import to Group Enter 1 to create a group by the device name. All the channels of the device will be imported to the corresponding group by default. Enter 0 to disable this function. 6. Click 7. Click Add to import the devices. and select the template file. 8.2.2 Reset Device Password If you forgot the password of the detected online devices, you can reset the device password via the client. Steps 1. Enter Device Management page. 2. Click Online Device to show the online device area. All the online devices sharing the same subnet will be displayed in the list. 3. Select the device from the list and click 4. Reset the device password. on the Operation column.

- Click Generate to pop up the QR Code window and click Download to save the QR code to your PC. You can also take a photo of the QR code to save it to your phone. Send the picture to our technical support. Note For the following operations for resetting the password, contact our technical support. 59 DS-K3B801SX Series Swing Barrier User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 8.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management. You can control door status, and do some other operations of the devices after managing the resources by groups. 8.3.1 Add Group You can add group to organize the added device for convenient management. Steps 1. Enter the Device Management module. 2. Click Device Management Group to enter the group management page. 3. Create a group.

- Click Add Group and enter a group name as you want.

- Click Create Group by Device Name and select an added device to create a new group by the name of the selected device. Note The resources (such as alarm inputs/outputs, access points, etc.) of this device will be imported to the group by default. 8.3.2 Import Resources to Group You can import the device resources (such as alarm inputs/outputs, access points, etc.) to the added group in a batch. 60 DS-K3B801SX Series Swing Barrier User Manual Before You Start Add a group for managing devices. Refer to Add Group . Steps 1. Enter the Device Management module. 2. Click Device Management Group to enter the group management page. 3. Select a group from the group list and select the resource type as Access Point, Alarm Input, Alarm Output, etc. 4. Click Import. 5. Select the thumbnails/names of the resources in the thumbnail/list view. Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 8.3.3 Edit Resource Parameters After importing the resources to the group, you can edit the resource parameters. For access point, you can edit the access point name. For alarm input, you can edit the alarm input name. Here we take access point as an example. Before You Start Import the resources to group. Steps 1. Enter the Device Management module. 2. Click Device Management Group to enter the group management page. All the added groups are displayed on the left. 3. Select a group on the group list and click Access Point. The access points imported to the group will display. in the Operation column to open the Edit Resource window. 4. Click 5. Edit the resource name. 6. Click OK to save the new settings. 8.3.4 Remove Resources from Group You can remove the added resources from the group. Steps 1. Enter the Device Management module. 2. Click Device Management Group to enter the group management page. All the added groups are displayed on the left. 3. Click a group to show the resources added to this group. 61 DS-K3B801SX Series Swing Barrier User Manual 4. Select the resource(s) and click Delete to remove the resource(s) from the group. 8.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 8.4.1 Add Organization You can add an organization and import person information to the organization for effective management of the persons. You can also add a surbodinate organization for the added one. Steps 1. Enter Person module. 2. Select a parent organization in the left column and click Add in the upper-left corner to add an 3. Create a name for the added organization. organization. Note Up to 10 levels of organizations can be added. 4. Optional: Perform the following operation(s). Edit Organization Hover the mouse on an added organization and click name. to edit its Hover the mouse on an added organization and click to delete it. Delete Organization Note organization. The lower-level organizations will be deleted as well if you delete an Make sure there is no person added under the organization, or the organization cannot be deleted. Show Persons in Sub Organization Check Show Persons in Sub Organization and select an organization to show persons in its sub organizations. 8.4.2 Configure Basic Information You can add person to the client one by one and configure the person's basic information such as name, gender, email, phone number, etc. 62 DS-K3B801SX Series Swing Barrier User Manual Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person. 3. Click Add to open the adding person window. The Person ID will be generated automatically. 4. Enter the basic information including person name, gender, telephone number, email address, validity period, etc. Figure 8-5 Configure Basic Information Note Once validity period expired, the credentials and access control settings of the person will be invalid and the person will have no authorization to access the doors\floors. You can click Extend to extend the person's validity period for 1 month, 3 months, 6 months, or 1 year. 5. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons. 8.4.3 Issue a Card by Local Mode If a card enrollment station is available, you can issue a card by local mode. To read the card number, you should connect the card enrollment station to the PC running the client by USB interface or COM, and place the card on the card enrollment station. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person panel. 63 DS-K3B801SX Series Swing Barrier User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Credential Card area, click +. 4. Click Settings to enter the Settings page. 5. Select Local as the card issuing mode. Figure 8-6 Issue a Card by Local Mode 6. Set other related parameters. Card Enrollment Station Select the model of the connected card enrollment station. Note Card Type Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-

M, DS-K1F100-D8E, and DS-K1F180-D8E. This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or Mifare card according to the actual card type. 64 DS-K3B801SX Series Swing Barrier User Manual Buzzing Card No. Type M1 Card Encryption Enable or disable the buzzing when the card number is read successfully. Select the type of the card number according to actual needs. This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-

D8E. If the card is M1 card, then you can enable the M1 Card Encryption function and select the sector of the card to encrypt. 7. Click OK to confirm the operation. 8. Place the card on the card enrollment station, and click Read to get the card number. The card number will display in the Card No. field automatically. 9. Click Add. The card will be issued to the person. 8.4.4 Upload a Face Photo from Local PC When adding person, you can upload a face photo stored in local PC to the client as the person's profile. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. Click Add Face in the Basic Information panel. 4. Select Upload. 5. Select a picture from the PC running the client. The picture should be in JPG or JPEG format and smaller than 200 KB. 6. Optional: Enable Verify by Device to check whether the facial recognition device managed in the client can recognize the face in the photo. Note Note Note This function is hidden or shown according to the device capacity. 7. Confirm to add the person.

- Click Add to add the person and close the Add Person window. 65 DS-K3B801SX Series Swing Barrier User Manual

- Click Add and New to add the person and continue to add other persons . 8.4.5 Take a Photo via Client When adding a person, you can take a photo of the her/him via the client and set this photo as the person's profile. Before You Start Make sure PC running the client has a camera or you have connected other USB camera to the PC. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add to enter Add Person window. Note Enter the person's basic information first. For details, refer to Configure Basic Information . 3. Click Add Face in the Basic Information area. 4. Select Take Photo to enter Take Photo window. 5. Optional: Enable Verify by Device to check whether the captured face photo can meet the uploading requirements. 6. Take a photo. 1) Face to the camera and make sure your face is in the middle of the collecting window. 2) Click 3) Optional: Click to capture again. 4) Click OK to save the captured photo. to capture a face photo. 66 DS-K3B801SX Series Swing Barrier User Manual Figure 8-7 Take a Photo via Client 7. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons. 8.4.6 Collect Face via Access Control Device When adding person, you can collect the person's face via access control device added to the client which supports facial recognition function. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. Click Add Face in the Basic Information panel. 67 DS-K3B801SX Series Swing Barrier User Manual 4. Select Remote Collection. 5. Select an added access control device or the enrollment station from the drop-down list. Note Face Anti-Spoofing 6. Collect face. If you select the enrollment station, you should click Login to set related parameters of the device including IP address, port No., user name, and password. Also, you can check Face Anti-

Spoofing and select the liveness level as Low, Medium, or High. If you check this function, then the device can detect whether the face to be collected is an authentic one. 1) Face to the camera of the selected access control device and make sure your face is in the middle of the collecting window. 2) Click to capture a photo. 3) Click OK to save the captured photo. 7. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons . 8.4.7 Collect Fingerprint via Client Collecting fingerprints locally means you can collect the fingerprint via the fingerprint recorder connected directly to the PC running the client. The fingerprints recorded can be used as credentials of the persons to access the authorized doors. Before You Start Connect the fingerprint recorder to the PC running the client. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Note Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Credential Fingerprint panel, click +. 4. In the pop-up window, select the collection mode as Local. 5. Select the model of the connected fingerprint recorder. If the fingerprint recorder is DS-K1F800-F, you can click Settings to select the COM the fingerprint recorder connects to. 68 DS-K3B801SX Series Swing Barrier User Manual 6. Collect the fingerprint. 1) Click Start. 2) Place and lift your fingerprint on the fingerprint recorder to collect the fingerprint. 3) Click Add to save the recorded fingerprint. 7. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons. Once the fingerprint is added, the fingerprint type cannot be changed. Note Note Note 8.4.8 Collect Fingerprint via Access Control Device When adding person, you can collect fingerprint information via the access control device's fingerprint module. The fingerprints recorded can be used as credentials of the persons to access the authorized doors. Before You Start Make sure fingerprint collection is supported by the access control device. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Credential Fingerprint panel, click +. 4. In the pop-up window, select the collection mode as Remote. 5. Select an access control device which supports fingerprint recognition function from the drop-

down list. 6. Collect the fingerprint. 1) Click Start. 2) Place and lift your fingerprint on the fingerprint scanner of the selected access control device to collect the fingerprint. 3) Click Add to save the recorded fingerprint. 7. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons . Once the fingerprint is added, the fingerprint type cannot be changed. 69 DS-K3B801SX Series Swing Barrier User Manual 8.4.9 Configure Access Control Information When adding a person, you can set her/his access control information, such as binding an access control group with the person, configuring PIN code, setting the person as a visitor, a blocklist person, or a super user, etc. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. 3. In the Access Control area, click to select access group(s) for the person. Note For details, refer to Set Access Group to Assign Access Authorization to Persons . Figure 8-8 Configure Access Control Information 4. Set a unique PIN code for the person which can be used for access authentication.

- Manually enter a PIN code containing 4 to 8 digits. Persons' PIN codes cannot be repeated.

- Click Generate to randomly generate an unrepeated PIN code of 6 digits. Note Note If there are repeated PIN codes, a prompt will pop up on the client. The admin can generate a new PIN code to replace the repeated PIN code and notify related persons. 5. Check the person's operation permissions. Super User If the person is set as a super user, he/she will have authorization to access all the doors/

floors and will be exempted from remaining closed restrictions, all anti-passback rules, and first person authorization. Extended Door Open Time Use this function for persons with reduced mobility. When accessing the door, the person will have more time than others to pass through doors. 70 DS-K3B801SX Series Swing Barrier User Manual For details about setting the door's open duration, refer to Configure Parameters for Door . Add the person to the blocklist and when the person tries to access doors/floors, an event will be triggered and sent to the client to notify the security personnel. If the person is a visitor, you should set the her/his valid times for visit. The valid times for visit is between 1 and 100. You can also check No Limit, then there are no limited times for the visitor to access doors/floors. For person with device operator role, he/she is authorized to operate on the access control devices. Add to Blocklist Mark as Visitor Note Device Operator Note The Super User, Extended Door Open Time, Add to Blocklist, and Mark as Visitor functions cannot be enabled concurrently. For example, if one person is set as super user, you cannot enable extended door open time for her/him, add her/him to the blocklist, or set her/him as visitor. 6. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons. 8.4.10 Customize Person Information You can customize the person properties which are not pre-defined in the client according to actual needs, e.g., place of birth. After customizing, when add a person, you can enter the custom information to make the person information complete. Steps 1. Enter Person module. 2. Set the fields of custom information. 1) Click Custom Property. 2) Click Add to add a new property. 3) Enter the property name. 4) Click OK. 3. Set the custom information when adding a person. 1) Select an organization in the organization list to add the person and click Add. 71 DS-K3B801SX Series Swing Barrier User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 2) In the Custom Information panel, enter the person information. 3) Click Add to add the person and close the Add Person window, or click Add and New to add the person and continue to add other persons. 8.4.11 Configure Resident Information If the person is resident, for video intercom purpose, you need to set the room number for her/him and bind an indoor station. After bound, you can call this person by calling the indoor station and perform video intercom with her/him. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Resident Information panel, select the indoor station to bind it to the person. Note Note If you select Analog Indoor Station, the Door Station field will display and you are required to select the door station to communicate with the analog indoor station. 4. Enter the floor No. and room No. of the person. 5. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons. 8.4.12 Configure Additional Information When adding person, you can configure the additional information for the person, such as person's identity type, identity No., country, etc., according to actual needs. Steps 1. Enter Person module. 2. Select an organization in the organization list to add the person and click Add. 72 DS-K3B801SX Series Swing Barrier User Manual Note Enter the person's basic information first. For details about configuring person's basic information, refer to Configure Basic Information . 3. In the Additional Information panel, enter the additional information of the person, including person's ID type, ID No., job title, etc., according to actual needs. 4. Confirm to add the person.

- Click Add to add the person and close the Add Person window.

- Click Add and New to add the person and continue to add other persons . 8.4.13 Import and Export Person Identify Information You can import the information and pictures of multiple persons to the client software in a batch. Meanwhile, you can also export the person information and pictures and save them in your PC. 8.4.14 Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5. Click Download Template for Importing Person to download the template. 6. Enter the person information in the downloaded template. If the person has multiple cards, separate the card No. with semicolon. Items with asterisk are required. By default, the Hire Date is the current date. 7. Click 8. Click Import to start importing. to select the CSV/Excel file with person information from local PC. Note Note importing. If a person No. already exists in the client's database, delete the existing information before You can import information of no more than 2,000 persons. 73 DS-K3B801SX Series Swing Barrier User Manual 8.4.15 Import Person Pictures After importing face pictures for the added persons to the client, the persons in the pictures can be identified by an added face recognition terminal. You can either import person pictures one by one, or import multiple pictures at a time according to your need. Before You Start Be sure to have imported person information to the client beforehand. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel and check Face. 4. Optional: Enable Verify by Device to check whether face recognition device managed in the client can recognize the face in the photo. to select a face picture file. 5. Click Note The (folder of) face pictures should be in ZIP format. Each picture file should be in JPG format and should be no larger than 200 KB. Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed. 8.4.16 Export Person Information You can export the added persons' information to local PC as a CSV/Excel file. Before You Start Make sure you have added persons to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' information will be exported if you do not select any organization. 3. Click Export to open the Export panel. 4. Check Person Information as the content to export. 5. Check desired items to export. 6. Click Export to save the exported file in CSV/Excel file on your PC. 74 DS-K3B801SX Series Swing Barrier User Manual 8.4.17 Export Person Pictures You can export face picture file of the added persons and save in your PC. Before You Start Make sure you have added persons and their face pictures to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. All persons' face pictures will be exported if you do not select any organization. 3. Click Export to open the Export panel and check Face as the content to export. 4. Click Export to start exporting. Note Note Steps Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 8.4.18 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details, fingerprint, and issued card information), you can get the person information from the device and import them to the client for further operations. If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client. The gender of the persons will be Male by default. If the card number or person ID (employee ID) stored on the device already exists in the client database, the person with this card number or person ID will not be imported to the client. 1. Enter Person module. 2. Select an organization to import the persons. 3. Click Get from Device. 4. Select an added access control device or the enrollment station from the drop-down list. 75 DS-K3B801SX Series Swing Barrier User Manual Note Note If you select the enrollment station, you should click Login, and set IP address, port No., user name and password of the device. 5. Click Import to start importing the person information to the client. Up to 2,000 persons and 5,000 cards can be imported. The person information, including person details, person's fingerprint information (if configured), and the linked cards (if configured), will be imported to the selected organization. 8.4.19 Move Persons to Another Organization You can move the added persons to another organization if you need. Before You Start Make sure you have added at least two organizations. Make sure you have imported person information. Steps 1. Enter Person module. 2. Select an organization in the left panel. The persons under the organization will be displayed in the right panel. 3. Select the person to move. 4. Click Change Organization. 5. Select the organization to move persons to. 6. Click OK. 8.4.20 Issue Cards to Persons in Batch Steps 1. Enter Person module. 2. Click Batch Issue Cards. The client provides a convenient way to issue cards to multiple persons in a batch. All the added persons with no card issued will be displayed in the right panel. 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need 4. Optional: Click Settings to set the card issuing parameters. For details, refer to Issue a Card by 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing issuing cards. Local Mode . cards. 76 DS-K3B801SX Series Swing Barrier User Manual 6. Click the Card No. column and enter the card number.

- Place the card on the card enrollment station.

- Swipe the card on the card reader.

- Manually enter the card number and press the Enter key. The person(s) in the list will be issued with card(s). 8.4.21 Report Card Loss If the person lost his/her card, you can report the card loss so that the card's related access authorization will be inactive. Steps 1. Enter Person module. 2. Select the person you want to report card loss for and click Edit to open the Edit Person window. 3. In the Credential Card panel, click on the added card to set this card as lost card. After reporting card loss, the access authorization of this card will be invalid and inactive. Other person who gets this card cannot access the doors by swiping this lost card. 4. Optional: If the lost card is found, you can click to cancel the loss. After cancelling card loss, the access authorization of the person will be valid and active. 5. If the lost card is added in one access group and the access group is applied to the device already, after reporting card loss or cancelling card loss, a window will pop up to notify you to apply the changes to the device. After applying to device, these changes can take effect on the device. 8.4.22 Set Card Issuing Parameters The client provides two modes for reading a card's number: via card enrollment station or via the card reader of the access control device. If a card enrollment station is available, connect it to the PC running the client by USB interface or COM, and place the card on the card enrollment to read the card number. If not, you can also swipe the card on the card reader of the added access control device to get the card number. As a result, before issuing a card to one person, you need to set the card issuing parameters including the issuing mode and related parameters. When adding a card to one person, click Settings to open the Card Issuing Settings window. Local Mode: Issue Card by Card Enrollment Station Connect a card enrollment station to the PC running the client. You can place the card on the card enrollment station to get the card number. Card Enrollment Station Select the model of the connected card enrollment station 77 DS-K3B801SX Series Swing Barrier User Manual Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E. Note Card Type Serial Port Buzzing Card No. Type M1 Card Encryption This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or IC card according to the actual card type. It is only available when the model is DS-K1F100-M. Select the COM the card enrollment station connects to. Enable or disable the buzzing when the card number is read successfully. Select the type of the card number according to actual needs. This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-D8E. If the card is M1 card, and if you need to enable the M1 Card Encryption function, you should enable this function and select the sector of the card to encrypt. Remote Mode: Issue Card by Card Reader Select an access control device added in the client and swipe the card on its card reader to read the card number. 8.5 Configure Schedule and Template You can configure the template including holiday and week schedule. After setting the template, you can adopt the configured template to access groups when setting the access groups, so that the access group will take effect in the time durations of the template. For access group settings, refer to Set Access Group to Assign Access Authorization to Persons . Note 8.5.1 Add Holiday You can create holidays and set the days in the holidays, including start date, end date, and holiday duration in one day. 78 DS-K3B801SX Series Swing Barrier User Manual Steps Note Note Note You can add up to 64 holidays in the software system. 1. Click Access Control Schedule Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5. Add a holiday period to the holiday list and configure the holiday duration. Up to 16 holiday periods can be added to one holiday. 1) Click Add in the Holiday List field. 2) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Up to 8 time durations can be set to one holiday period. 3) Optional: Perform the following operations to edit the time durations. Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to

. Click the time duration and directly edit the start/end time in the appeared dialog. Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to

. 4) Optional: Select the time duration(s) that need to be deleted, and then click in the Operation column to delete the selected time duration(s). in the Operation column to clear all the time duration(s) in the time bar. in the Operation column to delete this added holiday period from the Template includes week schedule and holiday. You can set week schedule and assign the time duration of access authorization for different person or group. You can also select the added holiday(s) for the template. 5) Optional: Click 6) Optional: Click holiday list. 6. Click Save. 8.5.2 Add Template Steps Note You can add up to 255 templates in the software system. 79 DS-K3B801SX Series Swing Barrier User Manual 1. Click Access Control Schedule Template to enter the Template page. There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. Note All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2. Click Add on the left panel to create a new template. 3. Create a name for the template. 4. Enter the descriptions or some notification of this template in the Remark box. 5. Edit the week schedule to apply it to the template. 1) Click Week Schedule tab on the lower panel. 2) Select a day of the week and draw time duration(s) on the timeline bar. Note Note Note Up to 8 time duration(s) can be set for each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to

. Click the time duration and directly edit the start/end time in the appeared dialog. Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to

. 4) Repeat the two steps above to draw more time durations on the other days of the week. 6. Add a holiday to apply it to the template. Up to 4 holidays can be added to one template. 1) Click Holiday tab. 2) Select a holiday in the left list and it will be added to the selected list on the right panel. 3) Optional: Click Add to add a new holiday. For details about adding a holiday, refer to Add Holiday . 4) Optional: Select a selected holiday in the right list and click or click Clear to clear all the selected holiday(s) in the right list. 7. Click Save to save the settings and finish adding the template. to remove the selected one, 80 DS-K3B801SX Series Swing Barrier User Manual 8.6 Set Access Group to Assign Access Authorization to Persons After adding the person and configuring the person's credentials, you can create the access groups to define which person(s) can get access to which door(s) and then apply the access group to the access control device to take effect. Before You Start Add person to the client. Add access control device to the client and group access points. For details, refer to Group Management . Add template. Steps When the access group settings are changed, you need to apply the access groups to the devices again to take effect. The access group changes include changes of template, access group settings, person's access group settings, and related person details (including card number, fingerprint, face picture, linkage between card number and fingerprint, linkage between card number and fingerprint, card password, card effective period, etc). 1. Click Access Control Authorization Access Group to enter the Access Group interface. 2. Click Add to open the Add window. 3. In the Name text field, create a name for the access group as you want. 4. Select a template for the access group. Note You should configure the template before access group settings. Refer to Configure Schedule and Template for details. 5. In the left list of the Select Person field, select person(s) to assign access authority. 6. In the left list of the Select Access Point field, select door(s), door station(s) or floor(s) for the selected persons to access. 7. Click Save. You can view the selected person(s) and the selected access point(s) on the right side of the interface. 81 DS-K3B801SX Series Swing Barrier User Manual Figure 8-9 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control 3) Click Apply All to Devices or Apply Changes to Devices. device or door station. Apply All to Devices This operation will clear all the existed access groups of the selected devices and then apply the new access group to the device. Apply Changes to Devices This operation will not clear the existed access groups of the selected devices and only apply the changed part of the selected access group(s) to the device(s). 4) View the applying status in the Status column or click Applying Status to view all the applied access group(s). Note Note You can check Display Failure Only to filter the applying results. The selected persons in the applied access groups will have the authorization to enter/exit the selected doors/door stations with their linked card(s) or fingerprints. 9. Optional: Click to edit the access group if necessary. If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. 82 DS-K3B801SX Series Swing Barrier User Manual You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 8-11 Data Synchronization 8.7 Configure Advanced Functions You can configure the advanced functions of access control to meet some special requirements in different scene. Note For the card related functions(the type of access control card), only the card(s) with access group applied will be listed when adding cards. The advanced functions should be supported by the device. Hover the cursor on the Advanced Function, and then Click function(s) to be displayed. to customize the advanced 8.7.1 Configure Device Parameters After adding the access control device, you can configure the parameters of access control device, access control points. Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters. Steps 1. Click Access Control Advanced Function Device Parameter . Note If you can find Device Parameter in the Advanced Function list, Hover the cursor on the Advanced Function, and then Click to select the Device Parameter to be displayed. 83 DS-K3B801SX Series Swing Barrier User Manual 2. Select an access device to show its parameters on the right page. 3. Turn the switch to ON to enable the corresponding functions. Note The displayed parameters may vary for different access control devices. RS-485 Communication Redundancy You should enable this function if you wire the RS-485 card reader to the access control device redundantly. If enable the function, the device can recognize the NFC card. You can present NFC card on the device. If enable the function, the device can recognize the M1 card. You can present M1 card on the device. If enable the function, the device can recognize the EM card. You can present EM card on the device. Reserved. If enable the function, the device can recognize the CPU card. You can present CPU card on the device. Enable NFC Enable M1 Card Enable EM Card Enable CPU Card Enable ID Card Reserved. If enable the function, the device can recognize the ID card. You can present ID card on the device. 4. Click OK. 5. Optional: Click Copy to, and then select the access control device(s) to copy the parameters in the page to the selected device(s). Configure Parameters for Door After adding the access control device, you can configure its access point door parameters. Steps 1. Click Access Control Advanced Function Device Parameter . 2. Select an access control device on the left panel, and then click the selected device. 3. Select a door or floor to show its parameters on the right page. 4. Edit the door or floor parameters. to show the doors or floors of 84 DS-K3B801SX Series Swing Barrier User Manual s The displayed parameters may vary for different access control devices. Note Name Edit the card reader name as desired. Exit Button Type You can set the exit button as remaining closed or remaining open. Usually, it is remaining open. Open Duration Door Left Open Timeout Alarm After swiping the normal card and relay action, the time for locking the door starts working. The alarm can be triggered if the door has not been closed in a configured time period. If it is set as 0, no alarm will be triggered. The specific person can open the door by inputting the super password. 5. Some of the following parameters are not listed in the Basic Information page, click Advanced The door can open by inputting the duress code when there is duress. At the same time, the client can report the duress event. Create a dismiss code which can be used to stop the buzzer of the card reader (by entering the dismiss code on the keypad). The duress code, super code, and dismiss code should be different. The duress code, super password, and the dismiss code should be different from the The length of duress code, super password, and the dismiss code is according the device, authentication password. usually it should contains 4 to 8 digits. 6. Click OK. 7. Optional: Click Copy to , and then select the door(s) to copy the parameters in the page to the selected doors(s). Note The door's status duration settings will be copied to the selected door(s) as well. Super Password to edit the parameters. Duress Code Dismiss Code Note 85 DS-K3B801SX Series Swing Barrier User Manual Configure Parameters for Card Reader After adding the access control device, you can configure its card reader parameters. Steps 1. Click Access Control Advanced Function Device Parameter . 2. In the device list on the left, click to expand the door, select a card reader and you can edit the card reader's parameters on the right. 3. Edit the card reader basic parameters in the Basic Information page. The displayed parameters may vary for different access control devices. There are part of parameters listed as follows. Refer to the user manual of the device for more details. Note Name Edit the card reader name as desired. Minimum Card Swiping Interval If the interval between card swiping of the same card is less than the set value, the card swiping is invalid. You can set it as 0 to 255. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. 4. Optional: Some of the following parameters are not listed in the Basic Information page, click Advanced to edit the parameters. Enable Card Reader If enabling the function, user can present card on the card reader. If disabling the function, the card reader for entrance cannot be used. OK LED Polarity/Error LED Polarity/Buzzer Polarity Set OK LED Polarity/Error LED Polarity/Buzzer LED Polarity of main board according to the card reader parameters. Generally, adopts the default settings. Buzzing Time Set the card reader buzzing time. The available time ranges from 0 to 5,999s. 0 represents continuous buzzing. Max. Interval When Entering PWD When you inputting the password on the card reader, if the interval between pressing two digits is larger than the set value, the digits you pressed before will be cleared automatically. Tampering Detection Enable the anti-tamper detection for the card reader. 86 DS-K3B801SX Series Swing Barrier User Manual Communicate with Controller Every When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Fingerprint Recognition Level Select the fingerprint recognition level in the drop-down list. 5. Click OK. 6. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s). Configure Parameters for Alarm Output After adding the access control device, if the device links to alarm outputs, you can configure the parameters. Before You Start Add access control device to the client, and make sure the device supports alarm output. Steps 1. Click Access Control Advanced Function Device Parameter to enter access control to expand the door, select an alarm input and you can edit parameter configuration page. 2. In the device list on the left, click the alarm input's parameters on the right. 3. Set the alarm output parameters. Name Edit the card reader name as desired. Alarm Output Active Time How long the alarm output will last after triggered. 4. Click OK. 5. Optional: Set the switch on the upper right corner to ON to trigger the alarm output. Configure Parameters for Lane Controller After adding the lane controller to the client, you can configure its parameters for passing through the lane. Steps 1. Click Access Control Advanced Function Device Parameter to enter Parameter Settings 2. In the device list on the left, select a lane controller and you can edit the lane controller's page. parameters on the right. 3. Edit the parameters. 87 DS-K3B801SX Series Swing Barrier User Manual Passing Mode Select the controller which will control the barrier status of the device. If you select According to DIP Settings, the device will follow the controller's DIP settings to control the barrier. The settings on the software will be invalid. If you select According to Door's Schedule Settings, the device will follow the schedule configured in the client software to control the barrier. The DIP settings of the controller will be invalid. Enable Free Passing Authentication After enabling free passing authentication, an alarm will be triggered when the passing personnel has no permission to pass through. Opening/Closing Barrier Speed Set the barrier's opening and closing speed. You can select from 1 to 10. The greater the value, the faster the speed. The recommended value is 6. Alarm Voice Prompt Duration Note Note Temperature Unit Lightboard Brightness Set the lightboard brightness. Barrier Material Set how long the audio will last, which is played when an alarm is triggered. 0 refers to the alarm audio will be played until the alarm is ended. Select the temperature unit that displayed in the device status. Select the material of the barrier gate. You can select the barrier material from the drop-

down list. The barrier material will affect the device working. Select a correct barrier material or the barrier may not open. The width of the lane. You can set the lane width. Lane Length Note Note The lane width will affect the device working. Set a correct lane width or the barrier may not open. 88 DS-K3B801SX Series Swing Barrier User Manual Do Not Open Barrier When Lane is Not Clear If there is someone or something in the lane, the gate will not open even if the credential is authenticated. This function is designed to avoid more than one person passing through the gate with only one authentication. 4. Click OK. 8.7.2 Configure Remaining Open/Closed You can set the status of the door as open or closed. For example, you can set the door remaining closed in the holiday, and set the door remaining open in the specified period of the work day. Before You Start Add the access control devices to the system. Steps 1. Click Access Control Advanced Function Remain Open/Closed to enter the Remain Open/

Closed page. 2. Select the door that need to be configured on the left panel. 3. To set the door status during the work day, click the Week Schedule and perform the following operations. 1) Click Remain Open or Remain Closed. 2) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Note Up to 8 time durations can be set to each day in the week schedule. 3) Optional: Perform the following operations to edit the time durations. Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to

. Click the time duration and directly edit the start/end time in the appeared dialog. Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to

. 4) Click Save. Related Operations Copy to Whole Week Select one duration on the time bar, click Copy to Whole Week to copy all the duration settings on this time bar to other week days. Delete Selected Select one duration on the time bar, click Delete Selected to delete this duration. Clear Click Clear to clear all the duration settings in the week schedule. 89 DS-K3B801SX Series Swing Barrier User Manual 4. To set the door status during the holiday, click the Holiday and perform the following operations. 1) Click Remain Open or Remain Closed. 2) Click Add. 3) Enter the start date and end date. 4) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Note Up to 8 time durations can be set to one holiday period. 5) Perform the following operations to edit the time durations. Move the cursor to the time duration and drag the time duration on the timeline bar to the desired position when the cursor turns to

. Click the time duration and directly edit the start/end time in the appeared dialog. Move the cursor to the start or the end of time duration and drag to lengthen or shorten the time duration when the cursor turns to

. 6) Optional: Select the time duration(s) that need to be deleted, and then click in the Operation column to delete the selected time duration(s). in the Operation column to clear all the time duration(s) in the time bar. in the Operation column to delete this added holiday period from the 7) Optional: Click 8) Optional: Click holiday list. 9) Click Save. 5. Optional: Click Copy to to copy the door status settings of this door to other door(s). 8.7.3 Configure Multi-Factor Authentication You can manage the persons by group and set the authentication for multiple persons of one access control point (door). Before You Start Set access group and apply the access group to the access control device. For details, refer to Set Access Group to Assign Access Authorization to Persons . Perform this task when you want to set authentications for multiple cards of one access control point (door). Steps 1. Click Access Control Advanced Function Multi-Factor Auth . 2. Select an access control device in device list on the left panel. 3. Add a person/card group for the access control device. 1) Click Add on the right panel. 2) Create a name for the group as desired. 3) Specify the start time and end time of the effective period for the person/card group. 4) Select members(s) and card(s) in the Available list, and the selected member(s) and card(s) will be added to the Selected list. 90 DS-K3B801SX Series Swing Barrier User Manual Make sure you have issue card to the person. Make sure you have set access group and apply the access group to the access control device successfully. 5) Click Save. 6) Optional: Select the person/card group(s), and then click Delete to delete it(them). 7) Optional: Select the person/card group(s), and then click Apply to re-apply access group that failed to be applied previously to the access control device. 4. Select an access control point (door) of selected device on the left panel. 5. Enter the maximum interval when entering password. 6. Add an authentication group for the selected access control point. 1) Click Add on the Authentication Groups panel. 2) Select a configured template as the authentication template from the drop-down list. Note Note For setting the template, refer to Configure Schedule and Template . 3) Select the authentication type as Local Authentication, Local Authentication and Remotely Open Door, or Local Authentication and Super Password from the drop-down list. Local Authentication Authentication by the access control device. Local Authentication and Remotely Open Door Authentication by the access control device and by the client. When the person swipes the card on the device, a window will pop up. You can unlock the door via the client. Figure 8-12 Remotely Open Door Note You can check Offline Authentication to enable the super password authentication when the access control device is disconnected with the client. Local Authentication and Super Password Authentication by the access control device and by the super password. 91 DS-K3B801SX Series Swing Barrier User Manual 4) Select the added person/card group in the left list below and it will be added to the Selected list on the right as the authentication group. 5) Click the added authentication group in the right list to set authentication times in the Auth The authentication times should be larger than 0 and smaller than the added personnel quantity in the personnel group. The maximum value of authentication times is 16. Times column. Note 6) Click Save. Note For each access control point (door), up to four authentication groups can be added. For the authentication group of which authentication type is Local Authentication, up to 8 person/card groups can be added to the authentication group. For the authentication group of which authentication type is Local Authentication and Super Password or Local Authentication and Remotely Open Door, up to 7 person/card groups can be added to the authentication group. Based on the knowledge of uploading rule for the third party Wiegand, you can set multiple customized Wiegand rules to communicate between the device and the third party card readers. 7. Click Save. 8.7.4 Configure Custom Wiegand Rule Before You Start Wire the third party card readers to the device. Steps Note By default, the device disables the custom wiegand function. If the device enables the custom Wiegand function, all wiegand interfaces in the device will use the customized wiegand protocol. Up to 5 custom Wiegands can be set. For details about the custom Wiegand, see Custom Wiegand Rule Descriptions. 1. Click Access Control Advanced Function Custom Wiegand to enter the Custom Wiegand page. 2. Select a custom Wiegand on the left. 3. Create a Wiegand name. Note Up to 32 characters are allowed in the custom Wiegand name. 92 DS-K3B801SX Series Swing Barrier User Manual 4. Click Select Device to select the access control device for setting the custom wiegand. 5. Set the parity mode according to the property of the third party card reader. Note Up to 80 bits are allowed in the total length. The odd parity start bit, the odd parity length, the even parity start bit and the even parity The start bit of the card ID, the manufacturer code, the site code, and the OEM should range length range from 1 to 80 bit. from 1 to 80 bit. 6. Set output transformation rule. 1) Click Set Rule to open the Set Output Transformation Rules window. Figure 8-13 Set Output Transformation Rule 2) Select rules on the left list. The selected rules will be added to the right list. 3) Optional: Drag the rules to change the rule order. 4) Click OK. 5) In the Custom Wiegand tab, set the rule's start bit, length, and the decimal digit. 7. Click Save. 8.7.5 Configure Card Reader Authentication Mode and Schedule You can set the passing rules for the card reader of the access control device according to your actual needs. 93 DS-K3B801SX Series Swing Barrier User Manual Steps 1. Click Access Control Advanced Function Authentication to enter the authentication mode configuration page. 2. Select a card reader on the left to configure. 3. Set card reader authentication mode. 1) Click Configuration. Figure 8-14 Select Card Reader Authentication Mode PIN refers to the PIN code set to open the door. Refer to Configure Access Control Information . 2) Check the modes in the Available Mode list and they will be added to the selected modes Note list. 3) Click OK. After selecting the modes, the selected modes will display as icons with different color. 4. Click the icon to select a card reader authentication mode, and drag the cursor to draw a color bar on the schedule, which means in that period of time, the card reader authentication is valid. 5. Repeat the above step to set other time periods. 94 DS-K3B801SX Series Swing Barrier User Manual Figure 8-15 Set Authentication Modes for Card Readers 6. Optional: Select a configured day and click Copy to Week to copy the same settings to the whole week. 7. Optional: Click Copy to to copy the settings to other card readers. 8. Click Save. 8.7.6 Configure First Person In You can set multiple first persons for one access control point. After the first person is authorized, it allows multiple persons access the door or other authentication actions. Before You Start Add access control device to the client, and make sure the device supports the first person in function. Add person and assign access authorization to designed person. For details, refer to Person Management and Set Access Group to Assign Access Authorization to Persons . Steps 1. Click Access Control Advanced Function First Person In to enter the First Person In page. 2. Select an access control device in the list on the left panel. 3. Select the current mode as Enable Remaining Open after First Person, Disable Remaining Open after First Person, or Authorization by First Person from the drop-down list for each access control point of the selected device. Enable Remaining Open after First Person The door remains open for the configured time duration after the first person is authorized until the remain open duration ends. If you select this mode, you should set the remain open duration. 95 DS-K3B801SX Series Swing Barrier User Manual The remain open duration should be between 0 and 1440 minutes. By default, the remain open duration is 10 minutes. Disable Remaining Open after First Person Disable the function of first person in, namely normal authentication. Authorization by First Person All authentications (except for the authentications of super card, super password, duress card, and duress code) are allowed only after the first person authorization. Note Note You can authenticate by the first person again to disable the first person mode. 4. Click Add on the First Person List panel. 5. Select person(s) in the left list and the person(s) will be add to the selected persons as the first person(s) of the doors. The added first person(s) will list in the First Person List 6. Optional: Select a first person from the list and click Delete to remove the person from the first person list. 7. Click Save. 8.7.7 Configure Anti-Passback The anti-passback feature is designed to minimizes the misuse or fraudulent use of access credentials such as passing back card to an unauthorized person, or tailed access. The anti-

passback function establishes a specific sequence in which access credentials must be used in order to grant access. You can set the sequence according to the actual path via the client and if the person uses the credential in wrong sequence, you can also reset the anti-password records. Before You Start Add access control device to the client, and enable the anti-passing back function of the access control device. Steps Note page. Either the anti-passing back or multi-door interlocking function can be configured for an access control device at the same time. For the configuration of multi-door interlocking, refer to . 1. Click Access Control Advanced Function Anti-Passback to enter the Anti-Passpack Settings 2. Select an access control device on the left panel. 3. Select a card reader as the beginning of the path in the First Card Reader field. 96 DS-K3B801SX Series Swing Barrier User Manual 4. Click of the selected first card reader in the Card Reader Afterward column to open the select card reader dialog. 5. Select the afterward card readers for the first card reader. Note Up to four afterward card readers can be added as afterward card readers for one card reader. 6. Click OK in the dialog to save the selections. 7. Click Save in the Anti-Passback Settings page to save the settings and take effect. Example Set Card Swiping Path: If you select Reader In_01 as the beginning, and select Reader In_02, Reader Out_04 as the linked card readers. Then you can only get through the access control point by swiping the card in the order as Reader In_01, Reader In_02 and Reader Out_04. 8. Click Reset Anti-Passback and select the person(s) to delete the related anti-passback records about the person(s) on the device. Note This function should be supported by the device. 8.7.8 Configure Device Parameters After adding the access control device, you can set its parameters such as network parameters. Set RS-485 Parameters You can set the access control device's RS-485 parameters including the baud rate, data bit, the stop bit, parity type, flow control type, communication mode, work mode, and connection mode. Steps Note page. 6. Click Save. The RS-485 Settings should be supported by the device. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function More Parameters . 3. Select an access control device in the device list and click RS-485 to enter the RS-485 Settings 4. Select the serial port number from the drop-down list to set the RS-485 parameters. 5. Set the serial number, external device, authentication center, baud rate, data bit, stop bit, parity type, flow control type, communication mode, and working mode in the drop-down list. 97 DS-K3B801SX Series Swing Barrier User Manual The configured parameters will be applied to the device automatically. When you change the working mode or connection mode, the device will reboot automatically. Enable M1 Card Encryption M1 card encryption can improve the security level of authentication. Steps Note The function should be supported by the access control device and the card reader. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function More Parameters . 3. Select an access control device in the device list and click M1 Card Encryption to enter the M1 Card Encryption page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. The sector ID ranges from 1 to 100. 6. Click Save to save the settings. 8.8 Configure Linkage Actions for Access Control You can configure different linkage actions for the event detected by the access control device. After that, linkage actions will be triggered once the event happens. This mechanism is used for notifying the security personnel the event, or triggering automatic access control in real time. Two types of linkage actions are supported:

Client Actions: When the event is detected, it will trigger the actions on the client, such as the client making an audible warning.. Device Actions: When the event is detected, it will trigger the actions of a specific device, such as buzzing of a card reader and, opening/closing of a door, .. 8.8.1 Configure Client Actions for Access Event Even if you are far away from an access point, you can still know what happens and how urgent the event is via the client by configuring client actions for the access event. Client actions here refer to the actions automatically executed by the client itself, such as making an audible warning and sending an email. Once an event is triggered, the client will notify the security personnel, so that he/she can handle the event in time. 98 DS-K3B801SX Series Swing Barrier User Manual Before You Start Add access control device to the client. Steps 1. Click Event Configuration Access Control Event . The added access control devices will display in the device list. 2. Select a resource (including device, alarm input, door, and card reader) from the device list. The event types which the selected resource supports appear. 3. Select the event(s) and click Edit Priority to define the priority for the event(s), which can be used to filter events in the Event Center. 4. Set the linkage actions of the event. 1) Select the event(s) and click Edit Linkage to set the client actions when the event(s) are triggered. Audible Warning Note Send Email The client software gives an audible warning when the event is triggered. You can select alarm sound for the audible warning. For details about setting the alarm sound, refer to Set Alarm Sound in the user manual of the client software. Send an email notification about the event to one or more receivers. For details about setting email parameters, refer to Set Email Parameters in the user manual of the client software. 5. Enable the event so that when the event is detected, event will be sent to the client and the 6. Optional: Click Copy to to copy the event settings to other access control device, alarm input, 2) Click OK. linkage actions will be triggered. door, or card reader. 8.8.2 Configure Device Actions for Access Event You can set the access control device's linkage actions for the access control device's triggered event. When the event is triggered, it can trigger the alarm output, host buzzer, and other actions on the same device. Steps Note It should be supported by the device. 1. Click Access Control Linkage Configuration . 99 DS-K3B801SX Series Swing Barrier User Manual 2. Select the access control device from the list on the left. 3. Click Add button to add a new linkage. 4. Select the event source as Event Linkage. 5. select the event type and detailed event to set the linkage. 6. In the Linkage Target area, set the property target to enable this action. Buzzer on Controller The audible warning of access control device will be triggered. 7. Click Save. 8. Optional: After adding the device linkage, you can do one or more of the following:

Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. 8.8.3 Configure Device Actions for Card Swiping You enable access control device's linkage actions (such as disarming a zone and triggering audio prompt) for the swiping of a specific card, In this way, you can monitor the card holder's behaviors and whereabouts. Steps Note It should be supported by the device. 1. Click Access Control Linkage Configuration . 2. Select the access control device from the list on the left. 3. Click Add to add a new linkage. 4. Select Card Linkage as the event source. 5. Enter the card number or select the card from the drop-down list. 6. Select the card reader where the card swipes. 7. In the Linkage Target area, set the property target to enable this action. The audible warning of access control device will be triggered. The audible warning of card reader will be triggered. Buzzer on Controller Buzzer on Reader Capture Recording An event-related picture will be captured when the selected event happens. An event-related picture will be captured when the selected event happens. 100 DS-K3B801SX Series Swing Barrier User Manual The device should support recording. The alarm output will be triggered for notification. Arm or disarm the alarm input. The device should support alarm input function. Note Alarm Output Alarm Input Note Access Point Audio Play 8. Click Save. The door status of open, close, remain open, or remain closed will be triggered. The audio prompt will be triggered. And the select audio index related audio content will be played according to the configured play mode. When the card (configured in Step 5) swipes on the card reader (configured in Step 6), it can trigger the linked actions (configured in step 7). 9. Optional: After adding the device linkage, you can do one or more of the followings:

Delete Linkage Settings Select the configured linkage settings in the device list and click Delete to delete it. Edit Linkage Settings Select the configured linkage settings in the device list and you can edit its event source parameters, including event source and linkage target. 8.9 Door Control In Monitoring module, you can view the real-time status of the doors managed by the added access control device. You can also control the doors such as open/close the door, or remain the door open/closed via the client remotely. The real-time access event are displayed in this module. You can view the access details and person details. Note For the user with door control permission, the user can enter the Monitoring module and control the door. Or the icons used for control will not show. For setting the user permission, refer to Person Management . 101 DS-K3B801SX Series Swing Barrier User Manual 8.9.1 Control Door Status You can control the status for the door(s), including unlock door, locking door, remaining the door unlock, remaining the door locked, remain all unlocked, etc. Before You Start Add person and assign access authorization to designed person, and person will have the access authorization to the access points (doors). For details, refer to Person Management and Set Access Group to Assign Access Authorization to Persons . Make sure the operation user has the permission of the access points (doors). For details, refer Steps 1. Click Monitoring to enter the status monitoring page. 2. Select an access point group on the upper-right corner. For managing the access point group, refer to Group Management . The doors in the selected access control group will display. 3. Click a door icon to select a door, or press Ctrl and select multiple doors. For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. to . Note Note Unlock Lock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials. Remain Unlocked Remain Locked Remain All Unlocked The door will be unlocked (no matter closed or open). All the persons can access the door with no credentials required. The door will be closed and locked. No person can access the door even if he/she has the authorized credentials, except the super users. All doors in the group will be unlocked (no matter closed or open). All the persons can access the doors with no credentials required. 102 DS-K3B801SX Series Swing Barrier User Manual All doors in the group will be closed and locked. No person can access the doors even if he/she has the authorized credentials, except the super users. Remain All Locked Capture Capture a picture manually. Note The Capture button is available when the device supports capture function. The picture is saved in the PC running the client. For setting the saving path, refer to Set File Saving Path in the user manual of the client software. Result The icon of the doors will change in real-time according to the operation if the operation is succeeded. 8.9.2 Check Real-Time Access Records The real-time access records can be displayed in the client, including card swiping records, face recognition records, skin-surface temperature information, etc. Also, you can view the person information and view the picture captured during access. Before You Start You have added person(s) and access control device(s) to the client. For details, refer to Person Management and Add Device . Steps 1. Click Monitoring to enter monitoring module. Real-time access records are displayed on the bottom of the page. You can view record details, including card No., person name, event time, door location, temperature, authentication type etc. Figure 8-16 Real-time Access Records 103 DS-K3B801SX Series Swing Barrier User Manual Note Note Note You can right click the column name of access event table to show or hide the column according to actual needs. 2. Optional: Select an access point group from the drop-down list in the upper-right corner to show the real time access records of the selected group. 3. Optional: Check the event type and event status. The detected events of checked type and status will be displayed in the list below. 4. Optional: Check Show Latest Event to view the latest access record. The record list will be listed reverse chronologically. 5. Optional: Check Enable Abnormal Temperature Prompt to enable abnormal skin-surface temperature prompt. When enabled, if there is abnormal temperature information, an Abnormal Temperature window pops up when you enter Monitoring module, displaying person's picture, skin-surface temperature, card No., person name, etc. 6. Optional: Click an event to view person pictures (including captured picture and profile). In Linked Capture Picture field, you can double click the captured picture to view an enlarged picture. 7. Optional: Click to view surveillance details (including person's detailed information and the In the pop-up window, you can click to view surveillance details in full screen. captured picture). Note 8.10 Event Center The event information (for example, device offline) received by the client displays. In the Event Center, you can check the detailed information of the real-time and historical events, view the event linked video, handle the events, and so on. Before the client can receive the event information from the device, you need to enable the events of the resource and arm the device first. For details, refer to Enable Receiving Event from Devices . 104 DS-K3B801SX Series Swing Barrier User Manual 8.10.1 Enable Receiving Event from Devices Before the client software can receive event notifications from the device, you need to arm the device first. Tool Device Arming Control to open Device Arming Control page. All the added devices appear on this page. 2. Optional: If there are to many devices, enter the key words in Filter filed to filter the device(s) Steps 1. Click you want. Note For the filtered devices, you can click Arm All or Disarm All to enable receiving event of these devices. 3. In the Auto-Arming column, turn on the switch to enable auto-arming. Figure 8-17 Arm Device After turned on, the device(s) will be armed. And notifications about the events triggered by the armed device(s) will be automatically sent to the client software in real-time. 8.10.2 View Real-Time Events The real-time event information received by the client of the connected resources are displayed. You can check the real-time event information, including event source, event time, priority, etc. 105 DS-K3B801SX Series Swing Barrier User Manual Before You Start Enable receiving events from devices before the client can receive event from the device, see Enable Receiving Event from Devices for details. Steps 1. Click Event Center Real-time Event to enter the real-time event page and you can view the real-time events received by the client. Event Time For encoding device, event time is the client time when it receives the event. For other device types, event time is the time when the event is triggered. Priority 2. Filter the events. Priority represents the emergency degree of the event. Filter by Device Type and (or) Priority Select device type(s) and (or) priorities to filter events. Filter by Keywords Enter the keywords to filter the events. 3. Optional: Right-click the table header of the event list to customize the event related items to be displayed in the event list. 4. Select an event in the event list to view the event details. 5. Optional: Perform the following operations if necessary. Handle Single Event Click Handle to enter the processing suggestion, and then click OK. Note After an event is handled, the Handle button will become Add Remark. Click Add Remark to add more remarks for this handled event. Handle Events in a Batch Select events that need to be processed, and then click Handle in Batch. Enter the processing suggestion, and then click OK. Click Audio On/Mute to enable/disable the audio of the event. Enable/Disable Alarm Audio Clear Events Send Email Select the Latest Event Automatically Check Auto-Select Latest Event to select the latest event automatically and the event information details is displayed. Click Clear to clear the all the events in the event list. Select an event and then click Send Email, and the information details of this event will be sent by email. 106 DS-K3B801SX Series Swing Barrier User Manual Note You should configure the email parameters first, see Set Email Parameters in the user manual of the client software for details. Auto-Play Video Check Auto-Play Video to automatically play video when displaying event details. Enlarge Video or Picture Double click the video image to view video in a larger window. to view picture in a Put the cursor on the picture, and click larger window. Download Captured Picture Hover the cursor on the captured picture, and click the download icon on the lower right corner of the picture to download it to the local PC. Download Event Triggered Video Hover the cursor on the recorded video, click video (30s before the event happens) triggered by the event. to download the 8.10.3 Search Historical Events You can search and view historical events by setting search conditions such as time, device type, and priority in the client. For the searched events, you can handle and export them. Before You Start Enable receiving events from devices before the client can receive event information from the device,see Enable Receiving Event from Devices for details. Steps 1. Click Event Center Event Search to enter the event search page. 2. Set the filter conditions to display the required events only. The time when the event starts. Search the events by device or the device's resource channels. If searched by device, you need to set the followings:

Include Sub-Node: Search the events of the device and all resource channels. Device Type: Select the device from which you want to search events. Search the events by resource channels in the group. Time Search by Device Group 107 DS-K3B801SX Series Swing Barrier User Manual Note Priority Event Type Note For video intercom device, you need to select search scope: All and Locking Log. For access control device, you can click Show More to set more conditions: status, event type, card reader type, person name, card No., and organization. The priority including low, medium, high and uncategorized which indicates the emergency degree of the event. Select one or more event types to be searched from the drop-down list. You can enter a key word (supports fuzzy search) in the search box to search the target event type(s). Status The handling status of the event. Search by Keyword Enter a key word (supports fuzzy search) to quickly search the target historical event(s). For example, you can enter a person's name to search the events related with this person. 3. Click Search to search the events according the conditions you set. Figure 8-18 Search Historical Events Note If you have selected Access Control as device type in Step 2, you can view extra information such as card No., skin-surface temperature, and abnormal temperature (if device supports) in the searched events. 108 DS-K3B801SX Series Swing Barrier User Manual 4. Optional: Right click the table header of the event list to customize the event related items to Figure 8-19 Search Historical Event be displayed in the event list. 5. Select an event in the event list to view the event details. 6. Optional: Perform one of the following operations. Handle Single Event Handle single event: Select one event that needs to be handled, and then click Handle in the event information details page, and enter the handling suggestion. Note Note After an event is handled, the Handle button will become Add Remark, click Add Remark to add more remarks for this handled event. Batch Handle Events Handle events in a batch: Select the events which need to be handled, and then click Handle in Batch, and enter the handling suggestion. After an event is handled, the Handle button will become Add Remark, click Add Remark to add more remarks for this handled event. Auto-Play Video Check Auto-Play Video to automatically play video when displaying event details. Enlarge Video or Picture Double click the video image to view video in a larger window. Put the cursor on the picture, and click to view picture in a larger window. 109 DS-K3B801SX Series Swing Barrier User Manual Send Email Select an event and then click Send Email, and the information details of this event will be sent by email. Note You should configure the email parameters first, see Set Email Parameters in the user manual of the client software for details. Export Event Information Click Export to export the event log or event pictures to the local PC in CSV/Excel file. You can set the saving path manually. Download Captured Picture Hover the cursor on the captured picture, and click the download icon on the lower right corner of the picture to download it to the local PC. Download Event Triggered Video Hover the cursor on the recorded video, click

(30s before the event happens) triggered by the event. to download the video 8.11 Remote Configuration via Client Software Configure device parameters remotely. 8.11.1 Check Device Information Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System Device Information and view the device basic information and the device to enter the remote configuration page. version information. 8.11.2 Edit Device Name to enter the remote configuration page. Click Maintenance and Management Device Management Device to enter the device list. Click Click System General to configure the device name and overwrite record files parameter. Click Save. 8.11.3 Edit Time Steps 1. Click Maintenance and Management Device Management Device to enter the device list. to enter the remote configuration page. 2. Click 3. Click System Time to configure the time zone. 110 DS-K3B801SX Series Swing Barrier User Manual 4. Optional: Check Enable NTP and set the NTP server address, the NTP port, and the synchronization interval. 5. Optional: Check Enable DST and set the DST start time, end time and the bias. 6. Click Save. 8.11.4 Set System Maintenance You can reboot the device remotely, restore the device to default settings, etc. Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System System Maintenance . 4. Maintain the device. to enter the remote configuration page. Reboot The device starts rebooting. Restore Default Settings Restore All Restore the device settings to the default ones, excluding the IP address. Restore the device parameters to the default ones. The device should be activated after restoring. 5. Remotely upgrade the device. 1) In the Remote Upgrade part, select an upgrade type. You need to set the device ID before upgrading if you select Controller Upgrade File as the remote upgrade type. Only the card reader that connected via RS-485 protocol supports upgrading. Note Note 2) Click ... to select an upgrade file. 3) Click Upgrade to start upgrading. Do not power off during the upgrading. 8.11.5 Manage Network User Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System User Network User . 4. Click Add to add the user. to enter the remote configuration page. 111 DS-K3B801SX Series Swing Barrier User Manual 5. Optional: Select a user in the user list and click Edit to edit the user. You are able to edit the user password, the IP address, the MAC address and the user permission. 6. Click OK. 8.11.6 Manage Keyfob User to enter the remote configuration page. Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System User Keyfob User . 4. Click Add to add the user. 5. Check Enable in the pop-up window and set the keyfob's serial No. 6. Optional: Enable the Remain Open Status of the turnstile. If enabling this function, after the keyfob is matching completed, you can set the barrier as remaining open by using the keyfob. Note Note 7. Set the door open direction 8. Click OK. Up to 32 keyfob users can be added. 8.11.7 Set Security Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System Security . 4. Select the density level in the drop-down list. 5. You can select Compatible Mode or Security Mode. to enter the remote configuration page. Compatible Mode Security Mode 6. Click Save. The user information verification is compatible with the old client software version when logging in. High security level during the user information verification when logging in. 112 DS-K3B801SX Series Swing Barrier User Manual 8.11.8 Configure Lane Parameters You can set the passing parameters for a person to pass through the turnstile. to enter the remote configuration page. Steps 1. Click Maintenance and Management Device to enter the device list. 2. Click 3. Click System Lane Settings . 4. Set the lane parameters. Door Closing Delay Time Set the delayed time duration when barrier is closing. The barrier will be closed after the configured delayed time. Max. Intrusion Duration If a person has entered the lane or passed through the lane for more than the configured time duration, an alarm will be triggered. 0 represents the function is disabled. The suggested minimum detection time duration is 2 s. Note Overstaying Duration If the device detects persons or things staying in the lane for more than the configured time duration, an alarm will be triggered. Max IR Obstructed Duration Set the maximum time duration for the obstruction of the IR light. If the IR light is obstructed for more than the configured time duration, the alarm will be triggered. 0 represents the function is disabled. 5. Click Save. 8.11.9 Configure Screen Parameters The device can connect to a text screen. You can set the display parameters on this page. Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System Screen Configuration . 4. Set the screen parameters. to enter the remote configuration page. For better performance, it is suggested to use the default parameters. Note Screen Position 113 DS-K3B801SX Series Swing Barrier User Manual Select the screen's position on the device. If select Exit from the drop-down list, the screen will be installed at the exit position of the device. Screen Model Font Size Select the screen model from the drop-down list. Select the text font size in the screen. Screen Orientation Select the text orientation on the screen. Set the space between two lines. Set the space between two columns. Line Space Column Spacing Initial Position 5. Click Save. 8.11.10 Configure Screen Parameters Set the first character's position displayed on the screen. You can set the people counting's parameters and after the configuration. Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click System People Counting . 4. Set the people counting parameters. to enter the remote configuration page. Clear Device People Counting Device People Counting Client Offline People Counting Click Reset and the counted people number will be restored to zero. Click Enable or Disable to enable or disable the people counting function. Click Enable or Disable to enable or disable function of the offline people counting on the client. If enabling the function and if the device is offline, the device will continue counting the people and the number will be stored in the device. When the device is online, the client will read the updated number from the device automatically. People Counting Type You can select from Invalid, By Detection, and By Authentication Number. 114 DS-K3B801SX Series Swing Barrier User Manual Invalid By Detection The device will not count people. If the device people counting function is enabled, the people counting function is still disabled. The device will count the people who passing through the device depending on the detection result. By Authentication Number The device will count the people who authenticating on the device. The failed authentication will also count as once. 5. Click Save. 8.11.11 Configure Advanced Network to enter the remote configuration page. Click Maintenance and Management Device Management Device to enter the device list. Click Click Network Advanced Settings and you can configure the DNS IP address 1 and the DNS IP address. Click Save to save the settings. 8.11.12 Configure Audio File You can relate the audio file to the corresponding playing scene. You can also export the audio file from the system and import the audio file from the local. Steps 1. Click Maintenance and Management Device Management Device to enter the device list. 2. Click 3. Click Other Audio File . to enter the remote configuration page. By default, the system contains the audio content. For details about the index related audio content, see Table of Audio Index Related Content . 4. Select the index (the playing content) corresponded play scene. 5. Optional: Input the descriptions of the play scene. 6. Click Save Parameters to save the relationship between the index (the playing content) and the 7. Optional: Click Export to export the default audio file to the local computer. 8. Optional: Click ... and select audio file from the local computer. Click Import to import the file to Note play scene. the device. 115 DS-K3B801SX Series Swing Barrier User Manual Note conversion manual. The imported audio file should be in MEM format. For details about converting other format of the audio file to MEM format, see the audio If you use the third part software to create or edit an audio file, the volume of the audio file should be no less than 0 68. If the volume is less than the value, it will exceed the loudspeaker's power consumption, so that damage the loudspeaker. 8.11.13 View Relay Status Click Maintenance and Management Device Management Device to enter the device list. Click to enter the remote configuration page. Click Status Relay and you can view the relay status. 116 DS-K3B801SX Series Swing Barrier User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger:

You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center. Incorrect Scanning The figures of scanning fingerprint displayed below are incorrect:

Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. 117 DS-K3B801SX Series Swing Barrier User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again. 118 DS-K3B801SX Series Swing Barrier User Manual Appendix B. DIP Switch B.1 DIP Switch Description The DIP switch is on the main lane control board. No.1 to No 8 is from the low bit to the high bit. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12. B.2 DIP Switch Corresponded Functions Note After setting the DIP switch, you should reboot the device, or the function cannot take effect. The 8-bit DIP switch corresponded functions on the access control board are as follows:

Bit Device Mode Function Decimal Value DIP Switch Address Diagram 1 to 2 Work Mode Normal Mode 3 Memory Mode Enable Memory Mode 0 1 2 0 Study Mode Test Mode 119 DS-K3B801SX Series Swing Barrier User Manual Bit Device Mode Function Decimal Value DIP Switch Address Diagram 4 Keyfob Paring Mode Disable Keyfob Paring Mode 5 to 8 Passing Mode Disable Memory Mode 1 0 1 0 1 2 4 5 6 Enable Keyfob Paring Mode Controlled Bi-

direction Controlled Entrance and Prohibit Exit Controlled Entrance and Free Exit Free Bi-direction 3 Free Entrance and Controlled Exit Free Entrance and Prohibit Exit Prohibited Bi-

direction 120 DS-K3B801SX Series Swing Barrier User Manual Bit Device Mode Function Decimal Value DIP Switch Address Diagram Prohibit Entrance and Controlled Exit Prohibit Entrance and Free Exit 7 8 121 DS-K3B801SX Series Swing Barrier User Manual Appendix C. Event and Alarm Type Event Alarm Type Tailgating Visual and Audible Reverse Passing Visual and Audible Force Accessing None Climb over Barrier Visual and Audible Overstay Visual and Audible Passing Timeout None Intrusion Visual and Audible Free Passing Authentication Failed Visual Barrier Obstructed None 122 DS-K3B801SX Series Swing Barrier User Manual Appendix D. Table of Audio Index Related Content Index Content Authenticated. Card No. does not exist. Card No. and fingerprint mismatch. Climbing over the barrier. Reverse passing. Passing timeout. Intrusion. Force accessing. Tailgating. No permissions. Authentication time out. Authentication failed. Expired card. Staying out of time. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 123 DS-K3B801SX Series Swing Barrier User Manual Appendix E. Error Code Description The swing barrier will display the error code on the seven-segment display if error occurred. Refer to the table below to find the description of each number. Error Reason Code Error Reason Code Normal Working The First IR Beam on Upper IR Board Triggered The Second IR Beam on Upper IR Board Triggered The Third IR Beam on Upper IR Board Triggered The Fourth IR Beam on Upper IR Board Triggered The Fifth IR Beam on Upper IR Board Triggered The Sixth IR Beam on Upper IR Board Triggered The Seventh IR Beam on Upper IR Board Triggered The Eighth IR Beam on Upper IR Board Triggered The Ninth IR Beam on Upper IR Board Triggered The Tenth IR Beam on Upper IR Board Triggered The Eleventh IR Beam on Upper IR Board Triggered The Twelfth IR Beam on Upper IR Board Triggered The First IR Beam on Lower IR Board Triggered The Second IR Beam on Lower IR Board Triggered 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Upper IR Board 5 Offline Upper IR Board 6 Offline Upper IR Board 7 Offline Upper IR Board 8 Offline Upper IR Board 9 Offline Upper IR Board 10 Offline Upper IR Board 11 Offline Upper IR Board 12 Offline Lower IR Board 1 Offline Lower IR Board 2 Offline Lower IR Board 3 Offline Lower IR Board 4 Offline Lower IR Board 5 Offline Lower IR Board 6 Offline Lower IR Board 7 Offline 124 DS-K3B801SX Series Swing Barrier User Manual Error Reason Code Error Reason Code The Third IR Beam on Lower IR Board Triggered The Fourth IR Beam on Lower IR Board Triggered The Fifth IR Beam on Lower IR Board Triggered The Sixth IR Beam on Lower IR Board Triggered The Seventh IR Beam on Lower IR Board Triggered The Eighth IR Beam on Lower IR Board Triggered The Ninth IR Beam on Lower IR Board Triggered The Tenth IR Beam on Lower IR Board Triggered The Eleventh IR Beam on Lower IR Board Triggered The Twelfth IR Beam on Lower IR Board Triggered Upper IR Board 1 Offline Upper IR Board 2 Offline Upper IR Board 3 Offline Upper IR Board 4 Offline 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Light Board Offline (Entrance) 49 Lower IR Board 8 Offline Lower IR Board 9 Offline Lower IR Board 10 Offline Lower IR Board 11 Offline Lower IR Board 12 Offline Light Board Offline (Exit) IR Adapter Offline (Up) IR Adapter Offline (Low) CAN Bus Exception Not Studying Obstruction Exceeding Studying Range Motor Exception 44 45 46 47 48 50 51 52 53 54 55 56 57 125 DS-K3B801SX Series Swing Barrier User Manual Appendix F. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure F-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands. Note that the command list contains all commonly used serial ports commands for all Hikvision access control and video intercom devices. Figure F-2 Device Command 126 UD22973B

HIKVISION Swing Barrier Model: DS-K3B801SX-R/E SN: C12345678 Date: 03/2021 UU MLTMRTY IVT, s2ctsanrossaonsam UP: 100-240V~, S0HZ/60Hz, 1.444.064 Contains FCC ID:2ADTD-K1102AEK Made in China This device complies with Part 15 of te FCC Rules. Operation is subject to the folowing two conditions:

C =

{Mithis device may not cause harmful interference, and

{@ithis device must accept any interference received, Including interference that may cause undesired operation. Manufacturer: Hangzhou Hikvision Digital Technology Co.,Ltd Address: No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China 612345678 12345678 HIKVISION Swing Barrier Model: DS-K3B801SX-R/M SN: 12345678 Date: 03/2021 Il MUNIN | It FCC ID:2ADTO-K9BBO1SXRM VP: 100-240V-, SOH2/60H2, 1.448-0.64 Contains FCC 1D:2ADTD-K1102AMK. Haden china Tico ih Pat 5 tn oe Re Span da kt ns C =

{thie device may not causa haul ierteenice, and

[apis device must accept ny ttretence receive, Inching inteforenes th may caso undesired operation. Manufacturer Hangzhou Hikvision Digital Technology Co.Ltd, Adrots: NOSES Qlanmo Road, Binjiang Distt, Mangzhou 310082, China 12345678 612345678

a) b) c) d) e) f) g) Title:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District Hangzhou 310052, China Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Xiuying Zhang 2ADTD 2ADTD-K3B801SXRM zhangxiuying@hikvision.com

+86-571-88075998 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Date:2021/04/28 Applicant Signature:

Print Name:

Xiuying Zhang Senior Certification engineer

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Hangzhou Hikvision Digital Technology Co., Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: 2021-04-28 Regarding: FCC ID: 2ADTD-K3B801SXRM To whom it may concern:

We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Hangzhou Hikvision Digital Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Xiuying Zhang Title: Senior Certification engineer Signature:

On behalf of Company: Hangzhou Hikvision Digital Technology Co., Ltd. Telephone: +86-0571-88075998-62460

Confidentiality Request regarding application for FCC ID: 2ADTD-K3B801SXRM SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States Hangzhou Hikvision Digital Technology Co., Ltd. To:

From: Hangzhou Hikvision Digital Technology Co., Ltd. No. 555 Qianmo Road, Binjiang District, angzhou 310052, China Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Xiuying Zhang Title: Senior Certification engineer Company Name: Hangzhou Hikvision Digital Technology Co., Ltd.

Current Date : 2021-04-27 Hangzhou Hikvision Digital Technology Co., Ltd. To:

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products

*WE (Hangzhou Hikvision Digital Technology Co., Ltd.) HEREBY DECLARED THAT Product Description Swing Barrier Model No. DS-K3B801SAX-L, DS-K3B801SAX-L/M, DS-K3B801SAX-L/E, DS-K3B801SAX-M, DS-K3B801SAX-M/M, DS-K3B801SAX-M/E, DS-K3B801SAX-R, DS-K3B801SAX-R/M, DS-K3B801SAX-R/E, DS-K3B801SAX-UHK, DS-K3B801SAX-CKV, DS-K3B801SAX-UVS, DS-K3B801SAX-KVO, DS-K3B801SAX-HUN,DS-K3B801SX-L, DS-K3B801SX-L/M, DS-K3B801SX-L/E, DS-K3B801SX-M, DS-K3B801SX-M/M, DS-K3B801SX-M/E, DS-K3B801SX-R, DS-K3B801SX-UHK, DS-K3B801SX-CKV, DS-K3B801SX-UVS, DS-K3B801SX-KVO, DS-K3B801SX-HUN,DS-K3B802X-L, DS-K3B802X-L/M, DS-K3B802X-L/E, DS-K3B802X-M, DS-K3B802X-M/M, DS-K3B802X-M/E, DS-K3B802X-R, DS-K3B802X-R/M, DS-K3B802X-R/E, DS-K3B802X-UHK, DS-K3B802X-CKV, DS-K3B802X-UVS, DS-K3B802X-KVO, DS-K3B802X-HUN Manufacturers Name Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturers Address No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

*Except that the model number, trade name and appearance and different modules deviation, are identical with the original product as follows:

Model No. ():

DS-K3B601SX-R/M, DS-K3B601SX-R/E Manufacturers Name ():

Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturers Address):

No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China Note1: The definition of identical should be electrically identical. A device will be considered to be electrically identical if no changes are made to the devices schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical. Note2: The product built into a certified module (DS-K1102AEK or DS-K1102AMK), the test data of different modules has been recorded in the report Contain moduler: 2ADTD-K1102AMK DS-K3B801SX-R/M, DS-K3B801SAX-L/M, DS-K3B801SAX-M/M, DS-K3B801SAX-R/M, DS-K3B801SX-L/M, DS-K3B801SX-M/M, DS-K3B802X-L/M, DS-K3B802X-M/M, DS-K3B802X-R/M, Contain moduler: 2ADTD-K1102AEK DS-K3B801SX-R/E, DS-K3B801SAX-L/E, Hangzhou Hikvision Digital Technology Co., Ltd. undefined DS-K3B801SAX-L, DS-K3B801SAX-M, DS-K3B801SAX-R, DS-K3B801SAX-M/E, DS-K3B801SAX-R/E, DS-K3B801SX-L/E, DS-K3B801SX-M/E, DS-K3B802X-L/E, DS-K3B802X-M/E, DS-K3B802X-R/E, DS-K3B801SAX-UHK, DS-K3B801SAX-CKV, DS-K3B801SAX-UVS, DS-K3B801SAX-KVO, DS-K3B801SAX-HUN,DS-K3B801SX-L, DS-K3B801SX-M, DS-K3B801SX-R, DS-K3B801SX-UHK, DS-K3B801SX-CKV, DS-K3B801SX-UVS, DS-K3B801SX-KVO, DS-K3B801SX-HUN,DS-K3B802X-L, DS-K3B802X-M, DS-K3B802X-R, DS-K3B802X-UHK, DS-K3B802X-CKV, DS-K3B802X-UVS, DS-K3B802X-KVO, DS-K3B802X-HUN Model No. ():

DS-K3B801SX-R/M, DS-K3B801SX-R/E Manufacturers Name (): Hangzhou Hikvision Digital Technology Co., Ltd. Manufacturers Address

China No.555 Qianmo Road, Binjiang District, Hangzhou 310052, Sincerely, Signature ():

Printed Name ():

Xiuying Zhang Position/Title ():

Senior Certification engineer Contact Number ():

+86-571-88075998