Hui Zhou Gaoshengda Technology Co., LTD WCT16R2601F WIFI+BT Module IEEE 802.11 a/b/g/n/ac 2T/2R Model Number: WCT16R2601F Product Descrition The WCT16R2601F is a complete dual-band(2.4GHz and 5GHz)WIFI 22 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ base band /radio and Bluetooth 5.0.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It fully complies with IEEE 802.11 a/b/g/n/ac feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from an extended distance. Product Features Complies with IEEE 802.11b/g/n for 2.4GHz and IEEE 802.11a/n/ac 5GHz Wireless LAN. Bluetooth v5.0 Two transmit and Two receive path(2T2R) Works with all existing network nfrastructure. Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. UP to 866.7 Mbps High-Speed Transfer Rate in 802.11ac mode of operation. Operating SystemsLinux, Windows Low power consumption. Easy to install and configure. High speed usd 2.0 interface. ROHS compliant Product Specification Model WCT16R2601F Product Name WIF+BT Module Standard Interface 802.11 a/b/g/n/ac USB Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 866.7Mbps Modulation Method Frequency Band GFSK,/4-DQPSK,8DPSK(bluetooth) DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a) QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac) BLUETOOTH 2402~2480 MHz WIFI 2.4G: 2412~2462 MHz 5G: 5150~5350MHz, 5470~5725MHz5725~5850MHz Infrastructure Operation Mode Security WEP, TKIP, AES, WPA, WPA2 Operating Voltage 3.3V10%
Current Consumption 1000mA Antenna Type PIFA Operating Temperature 0 ~ 70C ambient temperature Storage Temperature
-40 ~ 80C ambient temperature Humidity 5 to 95 % maximum (non-condensing) PAGE 1 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WCT16R2601F NOTICE:
please keep this product and accessories attached to the places which children can't touch;
do not splash water or other liquid onto this product, otherwise it may cause damage;
do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
please keep this product away from flammable or naked flame;
please do not repair this product by yourself. Only qualified personnel can be repaired. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID:2AC23-WCT16 any similar wording that expresses the same meaning may be used. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. PAGE 2 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WCT16R2601F The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements. The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval. Trace antenna designs: Not applicable. The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/commercial use.The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter This radio transmitter FCC ID: 2AC23-WCT16 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antennas:
2.4G PIFA antenna 1 2 dBi PIFA antenna 22.98 dBi BT Antenna:
BRADE GSD Note: 1. The WIFI antenna 2 is permanently attached, cant be replaced. 2. Must use the same antenna type and gain equal to or lower than in the tables above. The concrete contents to check are the following three points.
) Must use the same antenna type and gain equal to or lower than in the tables above.;
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. 5G PIFA antenna 1 3 dBi PIFA antenna 2 2.80 dBi TYPE PIFA antenna GAIN 2 dBi PAGE 3 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WCT16R2601F Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur.Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre leradiateur et votre corps. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 etla conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformit de rf. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
Contains IC:12290A-WCT16 any similar wording that expresses the same meaning may be used. Notez que si le numro d'identification IC n'est pas visible lorsque le module est install dans un autre appareil, une tiquette indiquant le module attach doit galement tre affiche l'extrieur de l'appareil o le module est install. L'tiquette extrieure peut tre libelle comme suit: contient IC:
12290A-WCT16 toute expression similaire qui exprime le mme sens. 1the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
PAGE 4 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WCT16R2601F 3for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and 1les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour uneutilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
2le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et5 470-5 725 MHz doit se conformer la limite de p.i.r.e.;
3le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz)doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. This radio transmitter [IC:12290A-WCT16] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.
) Must use antenna such as PIFA with gain not exceeding 3 dBi;
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. Le prsent metteur radio [IC:12290A-WCT16] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Le contenu concret vrifier sont les trois points suivants.
) ) doit utiliser une antenne comme PIFA avec pifa gain n'excdant pas 3 dBi
) doivent tre installs de faon que l'utilisateur final ne peut pas modifier l'antenne
) La ligne dalimentation doit tre conue en 50ohm Le rseau correspondant peut tre utilis pour affiner la perte de retour, etc. Notice to OEM integrator Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/ICanada statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. PAGE 5 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD WCT16R2601F Must have on the host device a label showing Contains FCC ID: 2AC23-WCT16IC: 12290A-WCT16 The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. Any company of the host device which install this modular should perform the test of radiated &condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &15.207, 15.407, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and15.209 & 15.207, 15.407, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247and 15.407) listed on the grant, and that the host product manufacturer is responsible forcompliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AC23-WCT16 and Contains IC:
12290A-WCT16 l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc / (catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices -
003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc /
(metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID: 2AC23-WCT16IC: 12290A-WCT16 PAGE 6 OF 6 Version 1.0