FCC ID: XKB-XTRAWIC Standalone Payment Terminal

Lane/7000 User Guide www.ingenico.com 28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35 Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre Contents 1_Introduction 2_Unpacking 3_Recommendations 3_1 Safety 3_2 Security of your terminal

(tampering attempt detection) 3_3 Main Characteristics 3_3_1 Terminal 3_3_2 Power characteristics 3_3_3 Lane/7000 Power values in different modes 3_4 Functional description 3_5 Installation & Connections 3_5_1 Positionning the terminal 3_5_2 Inserting SAM (Secure access module) and Micro SD 3_5_3 Connecting the terminal to the host 3_5_4 Setting the Lane/7000 on the standpole adaptor 4_Daily use 4_1 Card reading 4_1_1 Swiping a card 4_1_2 Inserting a smart card 4_1_3 Reading a contactless card 2 4 5 6 6 7 9 9 10 11 11 12 12 13 15 16 18 18 18 18 18 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 4_2 Signature capture 4_3 Audio 5_Maintenance 5_1 Cleaning 5_1_1 Cleaning of the terminal 5_1_2 Entretien du terminal 5_1_3 Wartung von Endgerten 5_2 Transport and storage 5_3 Troubleshooting 6_Cables 7_Norms & Marking 7_1 Federal Communications Commission (FCC) Statement 7_2 Industry Canada (IC) Statement 7_3 Environment (WEEE, Batteries and Packaging) 7_4 Marking 19 19 20 20 20 20 21 21 21 23 24 24 25 25 26 3 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 1_Introduction Thank you for choosing an Ingenico payment terminal. We recommend you to read carefully this user guide: it gives you the necessary information about safety precautions, unpacking, installation and maintenance of your terminal. WARRANTY / SECURITY To benefit from the guarantee-related product, and to respect the security, we ask you to use only the power supply delivered in box with the product, entrusting maintenance operations only to an authorized person. Failure to comply with these instructions will void the manufacturers responsibility. This symbol indicates an important Warning. This symbol indicates a piece of advice. 4 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 2_Unpacking According to the model, the following items are included in the packaging box (including optional accessories) :

The terminal The box may also include the following items depending on your working confi guration :

An installation guide Cable (specifi c to connectivity requirements) Power supply unit and power cord A stylus Modules Screws to fi x the main cable and the module CAUTION The power supply unit provided with your equipment is specially designed for it. Do not use any other power supply. ADVICE Keep the packaging. It must be re-used whenever the terminal is shipped. Lane/7000 900027893 R11 000 02/0617 5 Copyright 2017 Ingenico All rights reserved 3_Recommendations 3_1 Safety Power on/Power down - Emergency stop To power on or power down the terminal, connect or disconnect the power supply from the electric outlet. Power supply unit CAUTION Only use the power supply AC/DC provided with Lane/7000 or the power provided by a cash register limited power source (LPS). Authorized power supply units :

Power Supply Unit Supplier Type Supplier reference Electrical characteristics Ingenico part number PHIHONG TECHNOLOGY Co. Ltd Wallplug PSC16E-

080L6IN-R PSC16A-

080L6IN-R 8VDC 2A Level VI 296199611 296196003 CAUTION Lithium battery cell The terminal is fitted with a lithium battery cell which is not accessible to the user. Only a qualified technician is authorized to open the unit and change this component. Risk of explosion if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions. Electrical power supply network The electrical outlet must meet the following criteria:

Must be installed near the equipment and easily accessible;

Must meet standards and regulations in the country of use. 6 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved Explosion areas Certain regulations restrict the use of radio equipment in chemical plants, fuel depots and any site where blasting is carried out. You are urged to comply with these regulations. The terminal shall be protected by a specially fi tted and certifi ed cover enabling use in proximity to a fuel pump. Connection of headset on audio jack Connection of headset on audio jack CAUTION An excessive acoustic pressure of headset can involve deafness!

WARNING We recommend to the customer to provide guidance to the cardholder as to avoid having his card close to any magnets on the device since the card may be damaged. There is one magnet in the stylus and another in its holder. 3_2 Security of your terminal

(tampering attempt detection) Your device fulfi ls current applicable PCI PTS security requirements. Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks are performed regularly after receipt. You should check, for example: that the keypad is fi rmly in place; that there is no evidence of unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader or any other part of your terminal. Such checks would provide warning of any unauthorised modifi cations to your terminal, and other suspicious behaviour of individuals that have access to your terminal. Your terminal detects any tampered state. In this state the terminal will repeatedly fl ash the message Alert Irruption! and further use of the terminal will not be possible. If you observe the Alert Irruption!

message, you should contact the terminal helpdesk immediately. You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently verifi ed as being trustworthy. The terminal must never be put in or left at a location where it could be stolen or replaced by another device. as being trustworthy. The terminal must never be put in or left at a location where it could be stolen or replaced by another device. Lane/7000 900027893 R11 000 02/0617 7 Copyright 2017 Ingenico All rights reserved WARNING If the warranty label is torn or removed, the warranty will be void. CAUTION Positioning of the Lane/7000 on check stand must be in such a way to make cardholder PIN (Personal Identification Number) spying infeasible. Installing device on an adjustable stand must be in such a way that consumers can swivel the terminal sideways and/

or tilt it forwards/backwards to a position that makes visual observation of the PIN-entry process difficult. Positioning of in-store security cameras such that the PIN-entry keypad is not visible. NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being overlooked when entering their PIN Code. CAUTION This equipment may not be modified, altered or changed in any way without signed written permission from Ingenico 8 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 3_3 Main Characteristics 3_3_1 Terminal Weight

(Poids, Gewicht) Size

(dimensions, Mae) Display Touchscreen Operating conditions 583g (20.56 oz) 181 (L) x 152 (W) x 35.2 (H) mm 5 backlit LCD, WVGA (800 x 480 pixels) Capacitive Ambient temperature from 0C to +45C Max relative humidity 85% RH non-condensing at +40C Max altitude 2000 m Storage conditions Storage temperature

-20C, +55C Max relative humidity 85% at +55C 9 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 3_3_2 Power characteristics Power supply units The Lane/7000 can be powered by several ways :

An external power supply unit By POE (Power over Ethernet) By USB (5VDC or 12VDC) The characteristics for each type of power supply are detailed hereafter. 296199611 296196003 Model Name PSC16E-080L6IN-R PSC16A-080L6IN-R Weight 160g (5.6 oz) 160g (5.6 oz) Size (l x w x h) 74 x 35 x 46.2 mm 74 x 35 x 46.2 mm Class Level VI Level VI Input voltage AC 100-240V 50-60Hz AC 100-240V 50-60Hz Ouput voltage DC 8V 2A DC 8V 2A WARNING The power supply unit provided with your equipment is specially designed for this Ingenico terminal. Do not use any other power supply. The use of a power supply with apparently similar voltage/current characteristics may damage your terminal. AVERTISSEMENT Dans le cas o vous choisiriez dutiliser un bloc alimentation, assurez-vous de nutiliser que le bloc dalimentation qui a t conu spcialement pour votre terminal. Nutilisez pas dautre bloc dalimentation. Lemploi dun bloc dalimentation prsentant des caractristiques apparemment similaires de tension/intensit peut endommager votre terminal. 10 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved WARNHINWEIS Nur das Netzteil, das speziell fr Ihr Gert ausgelegt wurde, benutzen. Benutzen Sie kein anderes Netzteil. Die Benutzung eines Netzgerts mit scheinbar hnlicher Spannung/

Stromstrke kann zur Beschdigung Ihres Terminals fhren. 3_3_3 Lane/7000 Power values in different modes Lane/7000 works at voltages between 8VDC and 12VDC. Mode Lane/7000 Power (W) Idle mode - backlight OFF Idle mode - backlight ON Typical smartcard and contactless in test

- Backlight ON Maximum (+2 Loads of 2.5W each) 3 3.7 5 12 POE (Power over Ethernet) The power sourcing equipment must be compliant with IEEE802.3af standard, class 0 which means 12.95W max. 3_4 Functional description Stylus 5 inch-

touchscreen Contactless Reader Keypad Magnetic stripe Reader Smartcard Reader Lane/7000 900027893 R11 000 02/0617 11 Copyright 2017 Ingenico All rights reserved second Ethernet port Multipoint Connector Stanpole Adaptor pattern USB Type A port Speaker 3,5mm Audio Jack 3_5 Installation & Connections 3_5_1 Positioning the terminal Place the terminal with an easy access to an electrical outlet. Place the terminal away from any heat source and protected from dust, vibrations and electromagnetic radiations (away from video terminals, PC, anti-shoplifting barriers ...). The terminal is exclusively made for indoor use. The Lane/7000 device may be mounted on a fl at surface, wall, or customer stand. CAUTION Do not place the Lane/7000 device on a PC monitor, adjacent to an electronically active security tag deactivation system, or near other sources of magnetic fi elds. Lane/7000 900027893 R11 000 02/0617 12 Copyright 2017 Ingenico All rights reserved The Lane/7000 device must be at least 30 centimeters (12 inches) away from an electronically active type of security tag deactivation pad. An electronically active system sends out a powerful and potentially disruptive signal to deactivate the security tag. If the Lane/7000 device is placed too close to the systems pad, or placed above the pad, the product may not work properly. A passive system is a permanent magnet type that does not send out a signal. This type should not affect the Lane/7000 device. 3_5_2 Inserting SAM (Secure access module) and Micro SD CAUTION Before starting, switch off the terminal by disconnecting the power supply. Perform the following operations :

Unscrew the modules and remove them both Acess to SAM and Micro SD is now possible. Lane/7000 900027893 R11 000 02/0617 13 Copyright 2017 Ingenico All rights reserved Insert the SAM Card into the slot marked (1), (2) or (3). Take care to ensure that the SAM Card is inserted in the correct manner. The cut corner must be positioned as indicated on the figure below. Slide back the module and screw them tight 14 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved CAUTION Do not use any tools when installing or removing the SAM Card or Micro SD. WARNING During this operation, it is necessary to be in an ESD protected environment. As this is not very easy, it is recommended to make this operation using ESD shoes for example. 3_5_3 Connecting the terminal to the host CAUTION Connecting must be made when power supply unit is not plugged in the cable. 15 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved Flip the terminal. There is one port on the back for power and communications. Connect the cable on the terminal. Connect the other end to the power supply unit and a Host (PC / cash register). Plug the power supply into the mains. WARNING The main port at the back must not be used to connect an HDMI video cable. Only connect cables provided by Ingenico. Note : 2 screws can be added (M2.5 x 8) to hold more firmly the cable. 3_5_4 Setting the Lane/7000 on the stand-

pole adaptor Install the terminal on a flat surface is not possible on the Lane/7000 as is. It is designed to be fitted on a standpole adaptor. A specific pattern by Ingenico has been developed to fit the lane/7000. To fit the Lane/7000 to the stand pole adaptor, it only requires to slide down the Lane/7000 untl a click sound:

16 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved Click!

The Lane/7000 is now ready to use :

17 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 4_Daily use 4_1 Card reading 4_1_1 Swiping a card Insert the card manually in the reader, magnetic stripe facing the main body of the terminal, and slide the card from the rear to the front in a continuous motion for best results. Swipe the card with constant speed, neither too slowly nor too fast, to maximize the reading efficiency and avoid annoying repetitions. 4_1_2 Inserting a smart card Chip cards should be inserted into your terminal as illustrated with the chip facing up and into the card reader. 4_1_3 Reading a contactless card Bring the card to the active zone above the contactless logo (at about 1cm). Keep the card close to the contactless logo during the transaction. Your contactless terminal provides four contactless status lights located above the contactless logo. When a contactless transaction is started the first (left hand) status light will be lit steadily; this indicates that the contactless is in use but a card is not being read. When a contactless card is presented to the contactless active zone during a transaction the second, third and fourth status lights will be lit in turn. The card read is successful when all four status lights are lit and a confirmation tone can be heard. 18 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved CAUTION Do not stick any label onto the contactless active zone. It can decrease seriously contactless effi ciency. CAUTION Avoid metallic parts around the contactless area. 4_2 Signature capture The signature capture is done with a stylus and a capacitive touchscreen 4_3 Audio A speaker is available there is also an Audio jack. When a headset is plugged in, there is no more sound from the speaker. The audio jack is located next to the card reader. The audio jack is located next to the card reader. This option is not designed to play music, but to facilitate the use by blind people. The jack is 3.5mm, 32 ohms impedance. Lane/7000 900027893 R11 000 02/0617 19 Copyright 2017 Ingenico All rights reserved 4_4 Camera (optional) The Lane/7000 can be equiped with a module integrating a 5megapixels autofocus camera. Reference of the module : MODU/7005 WiFi Note: The Lane/7000 can be equiped with a module without camera. Reference of the module : MODU/7003 WiFi Lane/7000 900027893 R11 000 02/0617 19 Copyright 2019 Ingenico All rights reserved 5_Maintenance 5_1 Cleaning 5_1_1 Cleaning of the terminal CAUTION Before making any operations of maintenance in the terminal, make sure that the power supply is disconnected. First of all, unplug all the wires from the terminal. Good rules for proper cleaning of the terminal are :

Ingenico Cleaning kit Use cleaningcards.com/

: http://www.ingenico. Do not clean the electrical connections. Do not use in any case, solvents, detergents or abrasive products :

Those materials might damage the plastic or electrical contacts. Avoid exposing the terminal to the direct rays of the sun. Do not put anything into the slot of the smart card reader 5_1_2 Entretien du terminal ATTENTION Assurez-vous que tous les cbles sont bien dbranchs du terminal avant toute intervention de maintenance sur le terminal. Avant tout, dbranchez tous les cbles du terminal. Pour bien nettoyer le terminal :

Utilisez les kits de nettoyage Ingenico : http://www. ingenico.cleaningcards.com/

Ne nettoyez pas les connexions lectriques. Nutilisez jamais de solvants, de dtergents, dalcool ou de produits abrasifs :

Ces produits peuvent endommager le plastique ou les contacts lectriques. Evitez dexposer le terminal aux rayons directs du soleil. Ninsrez rien dans la fente du lecteur de carte. 20 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 5_1_3 Wartung von Endgerten ACHTUNG Stellen Sie vor jeglicher Wartungsarbeit an dem Terminal sicher, dass die Stromversorgung unterbrochen ist Als erstes alle Kabel vom Terminal trennen. Regeln fr eine ordnungsgemsse Reinigung des Terminals :

Fr die Auenseite des Terminals, Ingenico Cleaning kits benutzen: http://www.ingenico.cleaningcards.com/

Keine elektrischen Anschlsse reinigen. Auf keinen Fall Lsungsmittel, Waschmittel oder Scheuermittel verwenden:

diese Mittel knnen den Kunststoff oder elektrische Kontakte beschdigen. Das Terminal keiner direkten Sonneneinstrahlung aussetzen. Nichts in den Schlitz des Chipkartenlesers einfhren. CAUTION Before making any operations of maintenance in the terminal, make sure that the power supply is disconnected. 5_2 Transport and storage Use the original packaging for storage or returning the unit. Disconnect all cables from the terminal during the transport. 5_3 Troubleshooting Device is not working Make sure that the Lane/7000 connector is fully inserted into the back of the device. Restart the device. If you have another working Lane/7000 device, swap the devices to determine if the problem is with the device, cable, POS, or power supply. If the Lane/7000 device is directly connected to a host, reset the host by turning it off and back on again. 21 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved Magnetic Card Reader Does Not Work Properly When sliding the card through the reader, make sure that the magnetic stripe on the card is facing the Lane/7000 display screen (see Swiping a Magnetic Stripe Card). Swipe the card at a faster or middle steady speed. Inspect the magnetic stripe on the card to make sure it is not scratched or badly worn. Security tag deactivation system could disturb the magnetic card reader To determine if the problem is with the card :

a. If your host device has a magnetic stripe reader, try swiping the card there. b. If you have another working Lane/7000 device, try swiping the card there. Smart Card Reader Does Not Work Properly Make sure you have inserted correctly the smart card into the smart card reader and removed the card only after the transaction MicroSD Card Reader Does Not Work Properly Make sure you have inserted correctly the microSD card into the card reader. Check that the card capacity is not higher than 32GB. Touchscreen / Signature Capture Does Not Work Properly Make sure you use the correct power supply. Replace the stylus WARNING Changes or modifications to this device not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 22 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 6_Cables The terminal can be connected to the host by several ways, with optional cables :

High speed USB device Ethernet RS232 Most of the cables used with iSC and iPP ranges are compatible with the Lane/7000. We advise to check with your reseller their compatibility if you plan to replace an iSC480 / ISC250 / ISC Touch 250 by a Lane/7000. Following are some examples of accessories that can be used to connect the Lane/7000. This list is not exhaustive. Please contact your reseller for more information. RS232 cable (optional) Power supply unit Connector for terminal RS232 connector USB cable (optional) References : 296111170AC (length 2m) Connector for terminal Power supply unit USB connector USB powered 12V cable (optional) Connector for terminal Special USB shielded cable 12 V Lane/7000 900027893 R11 000 02/0617 23 Copyright 2017 Ingenico All rights reserved Ethernet cable (optional) Power supply unit Connector for terminal Ethernet connector 7_Norms & Marking 7_1 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 15.19 (a) (3) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation of the device. 24 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 7_2 Industry Canada (IC) Statement. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage, et 2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 7_3 Environment (WEEE, Batteries and Packaging) This product is labeled in accordance with European Directives 2002/96/EC concerning Waste Electrical and Electronic Equipment

(WEEE) and 2006/66/EC concerning Batteries and Accumulators. Those provisions are requiring producers and manufacturers to become liable for take-back, treatment and recycling upon end of life of equipment and batteries. The associated symbol means that WEEE and waste batteries must not be thrown away but collected separately and recycled. Ingenico ensures that efficient collection and recycling schemes are set-up for WEEE and batteries according to the local regulation of your country. Please contact your resellers for more detailed information about the compliance solution in place for disposing of your old product and used batteries. Packaging waste must also be collected separately to assure a proper disposal and recycling. Please note that proper recycling of the electrical and electronic equipment and waste batteries will ensure safety of human health and environment. 25 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved 7_4 Marking Below, you will fi nd the different symbols used on the product and its power supply. The CE marking is the manufacturers declaration that the product meets the requirements of the applicable EC directives. The CE mark is a mandatory conformity marking for certain products sold within the European Economic Area (EEA). This TV symbol shows consumers at a glance that a product has been examined by neutral experts and that there are no safety concerns The UL mark appears on end products and complete components suitable for factory and fi eld installation. All of the products carrying these marks are covered by our Follow-Up Services program to determine that products continue to be manufactured in compliance with ULs safety requirements. The RCM mark will be the only mark to indicate compliance with the Australian Communications and Media Authoritys (ACMA) regulatory arrangements for telecommunications, radio, EMC and electromagnetic energy (EME). The C-Tick is an identifi cation trademark registered to the Australian Communications Media Authority (ACMA). The C-Tick mark signifi es that the labelled electronic device is compliant with applicable electromagnetic compatibility (EMC) requirements Waste of Electrical and Electronic Equipment (WEEE) symbol indicates that when the end-user wishes to discard this product, it must be sent to separate collection facilities for recovery and recycling. By separating this product from other household-type waste, the volume of waste sent to incinerators or land-

fi lls will be reduced and natural resources will thus be conserved. This logo indicates that the product operates with an alternative voltage. This symbol is followed by the ratings (voltage and current for instance) Lane/7000 900027893 R11 000 02/0617 26 Copyright 2017 Ingenico All rights reserved This logo indicates that the product operates with a continuous voltage. This symbol is followed by the ratings (voltage and current for instance) Mark indicating a power supply meets the level VI requirements. Double insulated or class 2 electrical appliances are products that have been designed in a way so as not to require a safety connection to electrical earth (These products must NOT have a safety connection to Earth). Indoor use symbol. 27 Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reserved This Document is Copyright 2017 by INGENICO Group. INGENICO retains full copyright ownership, rights and protection in all material contained in this document. The recipient can receive this document on the condition that he will keep the document confidential and will not use its contents in any form or by any means, except as agreed beforehand, without the prior written permission of INGENICO. Moreover, nobody is authorized to place this document at the disposal of any third party without the prior written permission of INGENICO. If such permission is granted, it will be subject to the condition that the recipient ensures that any other recipient of this document, or information contained therein, is held responsible to INGENICO for the confidentiality of that information. Care has been taken to ensure that the content of this document is as accurate as possible. INGENICO however declines any responsibility for inaccurate, incomplete or outdated information. The contents of this document may change from time to time without prior notice, and do not create, specify, modify or replace any new or prior contractual obligations agreed upon in writing between INGENICO and the user. INGENICO is not responsible for any use of this device, which would be non-consistent with the present document. All trademarks used in this document remain the property of their rightful owners. Your contact Lane/7000900027893 R11 000 02/0617Copyright 2017 IngenicoAll rights reservedwww.ingenico.com28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre 28

Lane/8000 User Guide www.ingenico.com28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre Contents 1_Introduction 2_Unpacking 3_Recommendations 3_1 Safety 3_2 Security of your terminal

(tampering attempt detection) 3_3 Main Characteristics 3_3_1 Terminal 3_3_2 Power characteristics 3_3_3 Lane/8000 Power values in different modes 3_4 Functional description 3_5 Installation & Connections 3_5_1 Positionning the terminal 3_5_2 Inserting SAM (Secure access module) and Micro SD 3_5_3 Connecting the terminal to the host 3_5_4 Setting the Lane/8000 on the standpole adaptor 4_Daily use 4_1 Card reading 4_1_1 Swiping a card 4_1_2 Inserting a smart card 4_1_3 Reading a contactless card 2 4 5 6 6 7 9 9 10 11 11 12 12 13 15 15 17 17 17 17 17 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 4_2 Signature capture 4_3 Audio 4_4 Camera (optional) 5_Maintenance 5_1 Cleaning of the terminal 5_2 Transport and storage 5_3 Troubleshooting 6_Cables 7_Norms & Marking 7_1 Federal Communications Commission (FCC) Statement 7_2 Industry Canada (IC) Statement 7_3 Environment (WEEE, Batteries and Packaging) 7_4 Marking 18 18 19 20 20 20 20 22 23 23 24 24 25 3 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 1_Introduction Thank you for choosing an Ingenico payment terminal. We recommend you to read carefully this user guide: it gives you the necessary information about safety precautions, unpacking, installation and maintenance of your terminal. WARRANTY / SECURITY To benefit from the guarantee-related product, and to respect the security, we ask you to use only the power supply delivered in box with the product, entrusting maintenance operations only to an authorized person. Failure to comply with these instructions will void the manufacturers responsibility. This symbol indicates an important Warning. This symbol indicates a piece of advice. 4 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 2_Unpacking According to the model, the following items are included in the packaging box (including optional accessories) :

The terminal The box may also include the following items depending on your working configuration :

An installation guide Cable (specific to connectivity requirements) Power supply unit and power cord A stylus Modules Screws to fix the main cable and the module CAUTION The power supply unit provided with your equipment is specially designed for it. Do not use any other power supply. ADVICE Keep the packaging. It must be re-used whenever the terminal is shipped. 5 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 3_Recommendations 3_1 Safety Power on/Power down - Emergency stop To power on or power down the terminal, connect or disconnect the power supply from the electric outlet. Power supply unit CAUTION Only use the power supply AC/DC provided with Lane/8000 or the power provided by a cash register limited power source (LPS). Authorized power supply units :

Power Supply Unit Supplier PHIHONG TECHNOLOGY Co. Ltd Type Supplier reference Electrical characteristics Ingenico part number Desktop PSM24W-

080L6IN-R 8VDC 3A Level VI 296198809 Desktop Power Supply units have to be connected to the mains with one of these cables :

- Power cord 189609046 (EU)

- Power cord 188413214 (US) CAUTION Lithium battery cell The terminal is fitted with a lithium battery cell which is not accessible to the user. Only a qualified technician is authorized to open the unit and change this component. Risk of explosion if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions. 6 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved Electrical power supply network The electrical outlet must meet the following criteria:

Must be installed near the equipment and easily accessible;

Must meet standards and regulations in the country of use. Explosion areas Certain regulations restrict the use of radio equipment in chemical plants, fuel depots and any site where blasting is carried out. You are urged to comply with these regulations. The terminal shall be protected by a specially fi tted and certifi ed cover enabling use in proximity to a fuel pump. Connection of headset on audio jack Connection of headset on audio jack CAUTION An excessive acoustic pressure of headset can involve deafness!

3_2 Security of your terminal

(tampering attempt detection) Your device fulfi ls current applicable PCI PTS security requirements. Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks are performed regularly after receipt. You should check, for example: that the keypad is fi rmly in place; that there is no evidence of unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader or any other part of your terminal. Such checks would provide warning of any unauthorised modifi cations to your terminal, and other suspicious behaviour of individuals that have access to your terminal. Your terminal detects any tampered state. In this state the terminal will repeatedly fl ash the message Alert Irruption! and further use of the terminal will not be possible. If you observe the Alert Irruption!

message, you should contact the terminal helpdesk immediately. You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently verifi ed as being trustworthy. The terminal must never be put in or left at a location where it could be stolen or replaced by another device. as being trustworthy. The terminal must never be put in or left at a location where it could be stolen or replaced by another device. Lane/8000 900030066 R11 000 02/0119 7 Copyright 2019 Ingenico All rights reserved WARNING If the warranty label is torn or removed, the warranty will be void. CAUTION Positioning of the Lane/8000 on check stand must be in such a way to make cardholder PIN (Personal Identifi cation Number) spying infeasible. Installing device on an adjustable stand must be in such a way that consumers can swivel the terminal sideways and/

or tilt it forwards/backwards to a position that makes visual observation of the PIN-entry process diffi cult. Positioning of in-store security cameras such that the PIN-entry keypad is not visible. NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being overlooked when entering their PIN Code. CAUTION This equipment may not be modifi ed, altered or changed in any way without signed written permission from Ingenico Lane/8000 900030066 R11 000 02/0119 8 Copyright 2019 Ingenico All rights reserved 3_3 Main Characteristics 3_3_1 Terminal Weight

(Poids, Gewicht) Size

(dimensions, Mae) Display Touchscreen Operating conditions 796g 200 (L) x 205,5 (W) x 44 (H) mm 7 backlit LCD, WVGA (800 x 480 pixels) Capacitive Ambient temperature from 0C to +45C Max relative humidity 85% RH non-condensing at +40C Max altitude 2000 m Storage conditions Storage temperature

-20C, +70C Max relative humidity 85% at +55C 9 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 3_3_2 Power characteristics Power supply units The Lane/8000 can be powered by several ways :

An external power supply unit By POE (Power over Ethernet) By USB (12VDC) The characteristics for each type of power supply are detailed hereafter. 296198809 Model Name PSM24W-080L6IN-R Weight Size

(l x w x h) Class Input voltage Ouput voltage 243 g (8.57 oz) 120 x 50 x 31 mm Level VI AC 100-240V 50-60Hz DC 8V 3A WARNING The power supply unit provided with your equipment is specially designed for this Ingenico terminal. Do not use any other power supply. The use of a power supply with apparently similar voltage/current characteristics may damage your terminal. AVERTISSEMENT Dans le cas o vous choisiriez dutiliser un bloc alimentation, assurez-vous de nutiliser que le bloc dalimentation qui a t conu spcialement pour votre terminal. Nutilisez pas dautre bloc dalimentation. Lemploi dun bloc dalimentation prsentant des caractristiques apparemment similaires de tension/intensit peut endommager votre terminal. 10 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved WARNHINWEIS Nur das Netzteil, das speziell fr Ihr Gert ausgelegt wurde, benutzen. Benutzen Sie kein anderes Netzteil. Die Benutzung eines Netzgerts mit scheinbar hnlicher Spannung/

Stromstrke kann zur Beschdigung Ihres Terminals fhren. 3_3_3 Lane/8000 Power values in different modes Lane/8000 works at voltages between 8VDC and 12VDC. Mode Lane/8000 Power (W) Idle mode - backlight OFF Idle mode - backlight ON (50%) Typical SCR & CLESS - Backlight ON (50%) Maximum 3,1W 3,5W 8,8W 16W POE (Power over Ethernet) The power sourcing equipment must be compliant with IEEE802.3af standard, class 0 which means 12.95W max. 3_4 Functional description Stylus 7 inch-

touchscreen Contactless Reader Keypad Magnetic stripe Reader Smartcard Reader Lane/8000 900030066 R11 000 02/0119 11 Copyright 2019 Ingenico All rights reserved second Ethernet port Multipoint Connector Standpole Adaptor pattern USB Type A port Speaker 3,5mm Audio Jack 3_5 Installation & Connections 3_5_1 Positioning the terminal Place the terminal with an easy access to an electrical outlet. Place the terminal away from any heat source and protected from dust, vibrations and electromagnetic radiations (away from video terminals, PC, anti-shoplifting barriers ...). The terminal is exclusively made for indoor use. The Lane/8000 device may be mounted on a fl at surface, wall, or customer stand. CAUTION Do not place the Lane/8000 device on a PC monitor, adjacent to an electronically active security tag deactivation system, or near other sources of magnetic fi elds. The Lane/8000 device must be at least 30 centimeters (12 inches) away from an electronically active type of security tag deactivation pad. Lane/8000 900030066 R11 000 02/0119 12 Copyright 2019 Ingenico All rights reserved An electronically active system sends out a powerful and potentially disruptive signal to deactivate the security tag. If the Lane/8000 device is placed too close to the systems pad, or placed above the pad, the product may not work properly. A passive system is a permanent magnet type that does not send out a signal. This type should not affect the Lane/8000 device. 3_5_2 Inserting SAM (Secure access module) and Micro SD CAUTION Before starting, switch off the terminal by disconnecting the power supply. Perform the following operations :

Unscrew the modules and remove them both Access to SAM and Micro SD is now possible. Insert the SAM Card into the slot marked (1), (2) or (3). Take care to ensure that the SAM Card is inserted in the correct manner. The cut corner must be positioned as indicated on the fi gure below. Lane/8000 900030066 R11 000 02/0119 13 Copyright 2019 Ingenico All rights reserved Slide back the module and screw them tight CAUTION Do not use any tools when installing or removing the SAM Card or Micro SD. WARNING During this operation, it is necessary to be in an ESD protected environment. As this is not very easy, it is recommended to make this operation using ESD shoes for example. Lane/8000 900030066 R11 000 02/0119 14 Copyright 2019 Ingenico All rights reserved 3_5_3 Connecting the terminal to the host CAUTION Connecting must be made when power supply unit is not plugged in the cable. Flip the terminal. There is one port on the back for power and communications. Connect the cable on the terminal. Connect the other end to the power supply unit and a Host (PC / cash register). Plug the power supply into the mains. WARNING The main port at the back must not be used to connect an HDMI video cable. Only connect cables provided by Ingenico. Note : 2 screws can be added (M2.5 x 8) to hold more fi rmly the cable. 3_5_4 Setting the Lane/8000 on the stand-

pole adaptor Install the terminal on a fl at surface is not possible on the Lane/8000 as is. It is designed to be fi tted on a standpole adaptor. A specifi c pattern by Ingenico has been developed to fi t the Lane/8000. Lane/8000 900030066 R11 000 02/0119 15 Copyright 2019 Ingenico All rights reserved To fi t the Lane/8000 to the stand pole adaptor, it only requires to slide down the Lane/8000 until a click sound:

Click!

The Lane/8000 is now ready to use :

Lane/8000 900030066 R11 000 02/0119 16 Copyright 2019 Ingenico All rights reserved 4_Daily use 4_1 Card reading 4_1_1 Swiping a card Insert the card manually in the reader, magnetic stripe facing the main body of the terminal, and slide the card from the rear to the front in a continuous motion for best results. Swipe the card with constant speed, neither too slowly nor too fast, to maximize the reading effi ciency and avoid annoying repetitions. WARNING We recommend to the customer to provide guidance to the cardholder as to avoid having his card close to any magnets on the device since the card may be damaged. There is one magnet in the stylus and another in its holder. 4_1_2 Inserting a smart card Chip cards should be inserted into your terminal as illustrated with the chip facing up and into the card reader. 4_1_3 Reading a contactless card Bring the card to the active zone above the contactless logo (at about 1cm). Keep the card close to the contactless logo during the transaction. Your contactless terminal provides four contactless status lights located above the contactless logo. Lane/8000 900030066 R11 000 02/0119 17 Copyright 2019 Ingenico All rights reserved When a contactless transaction is started the fi rst (left hand) status light will be lit steadily; this indicates that the contactless is in use but a card is not being read. When a contactless card is presented to the contactless active zone during a transaction the second, third and fourth status lights will be lit in turn. The card read is successful when all four status lights are lit and a confi rmation tone can be heard. CAUTION Do not stick any label onto the contactless active zone. It can decrease seriously contactless effi ciency. CAUTION Avoid metallic parts around the contactless area. 4_2 Signature capture The signature capture is done with a stylus and a capacitive touchscreen 4_3 Audio A speaker is available there is also an Audio jack. When a headset is plugged in, there is no more sound from the speaker. The audio jack is located next to the card reader. The audio jack is located next to the card reader. This option is not designed to play music, but to facilitate the use by blind people. The jack is 3.5mm, 32 ohms impedance. Lane/8000 900030066 R11 000 02/0119 18 Copyright 2019 Ingenico All rights reserved 4_4 Camera (optional) The Lane/8000 can be equiped with a module integrating a 5 megapixels autofocus camera. Reference of the module : MODU/8005 WiFi Note: The Lane/8000 can be equiped with a module without camera. Reference of the module : MODU/7003 WiFi 19 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved

5_Maintenance CAUTION Before making any operations of maintenance in the terminal, make sure that power supply is disconnected. 5_1 Cleaning of the terminal First of all, unplug all the wires from the terminal. Good rules for proper cleaning of the terminal are :

Use a soft cloth that is very slightly sloated with soapy water to clean the outside of the terminal. Do not clean the electrical connections. Avoid exposing the terminal to the direct rays of the sun. Do not put anything into the slot of the smart card reader CAUTION Do not use in any case, solvents, detergents or abrasive products :

Those materials might damage the plastic or electrical contacts. 5_2 Transport and storage Use the original packaging for storage or returning the unit. Disconnect all cables from the terminal during the transport. 5_3 Troubleshooting Device is not working Make sure that the Lane/8000 connector is fully inserted into the back of the device. Restart the device. 20 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved If you have another working Lane/8000 device, swap the devices to determine if the problem is with the device, cable, POS, or power supply. If the Lane/8000 device is directly connected to a host, reset the host by turning it off and back on again. Magnetic Card Reader Does Not Work Properly When sliding the card through the reader, make sure that the magnetic stripe on the card is facing the Lane/8000 display screen (see Swiping a Magnetic Stripe Card). Swipe the card at a faster or middle steady speed. Inspect the magnetic stripe on the card to make sure it is not scratched or badly worn. Security tag deactivation system could disturb the magnetic card reader To determine if the problem is with the card :

a. If your host device has a magnetic stripe reader, try swiping the card there. b. If you have another working Lane/8000 device, try swiping the card there. Smart Card Reader Does Not Work Properly Make sure you have inserted correctly the smart card into the smart card reader and removed the card only after the transaction MicroSD Card Reader Does Not Work Properly Make sure you have inserted correctly the microSD card into the card reader. Check that the card capacity is not higher than 32GB. Touchscreen / Signature Capture Does Not Work Properly Make sure you use the correct power supply. Replace the stylus WARNING Changes or modifications to this device not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 21 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 6_Cables The terminal can be connected to the host by several ways, with optional cables:

High speed USB device Ethernet RS232 Most of the cables used with iSC and iPP ranges are compatible with the Lane/8000. We advise to check with your reseller their compatibility if you plan to replace an iSC480 / ISC250 / ISC Touch 250 by a Lane/8000. Following are some examples of accessories that can be used to connect the Lane/8000 (ACC-LANE8000). This list is not exhaustive. Please contact your reseller for more information. HDMI / RS232 (296114811AB) Power supply unit Connector for terminal HDMI / USB (296111170AD) Connector for terminal Connector for terminal RS232 connector Power supply unit USB connector HDMI / USB powered 12V (296178419AB) Connector for terminal Special USB shielded cable 12 V Lane/8000 900030066 R11 000 02/0119 22 Copyright 2019 Ingenico All rights reserved HDMI / Ethernet (296100040AF) Connector for terminal Power supply unit 7_Norms & Marking Ethernet connector Lane 8000 CLESS XKB-L8000CL 2586D-L8000CL FCC_ID IC_Number 7_1 Federal Communications Commis-

sion (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 23 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved 15.19 (a) (3) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation. 7_2 Industry Canada (IC) Statement. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions :

1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage, et 2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente

(p.i.r.e.) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. 7_3 Environment (WEEE, Batteries and Packaging) This product is labelled in accordance with European Directive 2002/96/EC concerning Waste Electrical and Electronic Equipment 24 Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reserved(WEEE). Ingenico ensures that effi cient collection and recycling schemes are set-up for WEEE according to the local regulation of your country. Please contact your retailers for more detailed information. Packaging waste must also be collected separately to assure a proper disposal and recycling. Please note that proper recycling of the WEEE will ensure safety of human health and environment. The associated symbol means that WEEE and waste batteries must not be thrown away but collected separately and recycled. Ingenico ensures that effi cient collection and recycling schemes are set-up for WEEE and batteries according to the local regulation of your country. Please contact your resellers for more detailed information about the compliance solution in place for disposing of your old product and used batteries. Packaging waste must also be collected separately to assure a proper disposal and recycling. Please note that proper recycling of the electrical and electronic equipment and waste batteries will ensure safety of human health and environment. 7_4 Marking Below, you will fi nd the different symbols used on the product and its power supply. The CE marking is the manufacturers declaration that the product meets the requirements of the applicable EC directives. The CE mark is a mandatory conformity marking for certain products sold within the European Economic Area (EEA). This TV symbol shows consumers at a glance that a product has been examined by neutral experts and that there are no safety concerns The UL mark appears on end products and complete components suitable for factory and fi eld installation. All of the products carrying these marks are covered by our Follow-Up Services program to determine that products continue to be manufactured in compliance with ULs safety requirements. Indoor use symbol. Lane/8000 900030066 R11 000 02/0119 25 Copyright 2019 Ingenico All rights reserved The RCM mark will be the only mark to indicate compliance with the Australian Communications and Media Authoritys (ACMA) regulatory arrangements for telecommunications, radio, EMC and electromagnetic energy (EME). The C-Tick is an identifi cation trademark registered to the Australian Communications Media Authority (ACMA). The C-Tick mark signifi es that the labelled electronic device is compliant with applicable electromagnetic compatibility

(EMC) requirements This logo indicates that the product operates with an alternative voltage. This symbol is followed by the ratings

(voltage and current for instance). This logo indicates that the product operates with a continuous voltage. This symbol is followed by the ratings

(voltage and current for instance) Mark indicating a power supply meets the level VI requirements. Double insulated or class 2 electrical appliances are products that have been designed in a way so as not to require a safety connection to electrical earth (These products must NOT have a safety connection to Earth). Indias Compulsory Registration Scheme Electronic Products.

(CRS) for The Electrical Appliance and Material Safety Law applies to enterprises that manufacture or import products in Japan China Compulsory Certifi cation (CCC) is similar to other certifi cations for product quality standardizationsuch as the European CE system The CSA mark on your product demonstrates to your customers, that a sample of the product has been certifi ed to applicable standards including standards written or administered by the American National Standards Institute

(ANSI), Underwriters Laboratories (UL), CSA Group (CSA), NSF International (NSF), and other North American and global organizations Lane/8000 900030066 R11 000 02/0119 26 Copyright 2019 Ingenico All rights reserved This Document is Copyright 2019 by INGENICO Group. INGENICO retains full copyright ownership, rights and protection in all material contained in this document. The recipient can receive this document on the condition that he will keep the document confidential and will not use its contents in any form or by any means, except as agreed beforehand, without the prior written permission of INGENICO. Moreover, nobody is authorized to place this document at the disposal of any third party without the prior written permission of INGENICO. If such permission is granted, it will be subject to the condition that the recipient ensures that any other recipient of this document, or information contained therein, is held responsible to INGENICO for the confidentiality of that information. Care has been taken to ensure that the content of this document is as accurate as possible. INGENICO however declines any responsibility for inaccurate, incomplete or outdated information. The contents of this document may change from time to time without prior notice, and do not create, specify, modify or replace any new or prior contractual obligations agreed upon in writing between INGENICO and the user. INGENICO is not responsible for any use of this device, which would be non-consistent with the present document. All trademarks used in this document remain the property of their rightful owners. Your contact Lane/8000900030066 R11 000 02/0119Copyright 2019 IngenicoAll rights reservedwww.ingenico.com28-32, boulevard de Grenelle, 75015 Paris - France / (T) +33 (0)1 58 01 80 00 / (F) +33 (0)1 58 01 91 35Ingenico - SA au capital de 47 656 332 / 317 218 758 RCS Nanterre 27

Module 1D Bar-Code Serial N SN: XXXXXXXXXXXX Module Ref 1D Bar-Code Ref: XXXXXXXXXXXX Rev:xx WIFI Adr:

Product: MODU/7003 WiFi FCC ID: XKB-XTRAWIC IC: 2586D-XTRAWIC XTRA WIFI Made in: xxxxxxx Module PN Serial Number Wifi adress Color : White RAL9010 Adhesive one side : Permanent UL969 certified Material : Vinyl or Polyester, thickness 50 to 100 m UL969 certified Adobe / ILLUSTRATOR ETABLI DRAWN NOM / NAME VSUC DATE 02/09/2022 VERIFIE CHECKED NOM / NAME CPELCAT LIBELLE DENOMINATION ETI MODULE XTRA AVEC RADIO LANE 7000/8000 XTRA MODULE LABEL WITH RADIO LANE 7000/8000

296260407 FORMAT SIZE 900039231 R40 FEUILLE / SHEET ECHELLE SCALE 1 DATE 02/09/2022 1/1 000 02 NUMERO DU DOCUMENT DRAWING NUMBER TYPE PART VERS.

Module 1D Bar-Code Serial N SN: XXXXXXXXXXXX Module Ref 1D Bar-Code Ref: XXXXXXXXXXXX Rev:xx WIFI Adr:

Product: MODU/7005 WiFi FCC ID: XKB-XTRAWIC IC: 2586D-XTRAWIC XTRA WIFI Made in: xxxxxxx Module PN Serial Number Wifi adress Color : White RAL9010 Adhesive one side : Permanent UL969 certified Material : Vinyl or Polyester, thickness 50 to 100 m UL969 certified Adobe / ILLUSTRATOR ETABLI DRAWN NOM / NAME VSUC LIBELLE DENOMINATION DATE 02/09/2022 VERIFIE CHECKED NOM / NAME CPELCAT ETI MODULE XTRA AVEC RADIO LANE 7000 XTRA MODULE LABEL WITH RADIO LANE 7000 FEUILLE / SHEET

296260407 FORMAT SIZE 900039231 R40 ECHELLE SCALE 1 DATE 02/09/2022 1/1 000 02 NUMERO DU DOCUMENT DRAWING NUMBER TYPE PART VERS.

Module 1D Bar-Code Serial N SN: XXXXXXXXXXXX Module Ref 1D Bar-Code Ref: XXXXXXXXXXXX Rev:xx WIFI Adr:

Product: MODU/8005 WiFi FCC ID: XKB-XTRAWIC IC: 2586D-XTRAWIC XTRA WIFI Made in: xxxxxxx Module PN Serial Number Wifi adress Color : White RAL9010 Adhesive one side : Permanent UL969 certified Material : Vinyl or Polyester, thickness 50 to 100 m UL969 certified Adobe / ILLUSTRATOR ETABLI DRAWN NOM / NAME VSUC LIBELLE DENOMINATION DATE 02/09/2022 VERIFIE CHECKED NOM / NAME CPELCAT ETI MODULE XTRA AVEC RADIO LANE 8000 XTRA MODULE LABEL WITH RADIO LANE 8000 FEUILLE / SHEET

296260407 FORMAT SIZE 900039231 R40 ECHELLE SCALE 1 DATE 02/09/2022 1/1 000 02 NUMERO DU DOCUMENT DRAWING NUMBER TYPE PART VERS.

DECLARATION LETTER Date: 2022-09-15 To Whom It May Concern:

We, Ingenico, as manufacturer of XTRA Module models, hereby declare that these modules under:

FCC ID: XKB-XTRAWIC and IC: 2586D-XTRAWIC, will only be used with Lane/7000 and Lane/8000 hosts, that the module will only be used by Ingenico and will not be sold to customers as a standalone product. Thanks for your attention on this matter. Yours faithfully Name Company Nicolas JACQUEMONT - HW Certification Manager INGENICO Signature

LONG-TERM CONFIDENTIALITY REQUEST for Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request Long-Term Confidentiality for the following product:

Grantee Code Equipment Product Code Check your GC here. Click Grantee Search. FCC ID:

For the product stated above, we request Long-Term Confidentiality for exhibits which contain Block Diagram, Operational Description, Parts List/Tune Up Info, Schematics, SDR Software/Security Info. The above exhibits contain our benefit to our competitors. This information will not be publicly available. trade secrets and proprietary information If you have any questions, please feel free to contact us at the address shown below. Sincerely, Company Name:

Company Address:

Contact Name:

Signature:

Phone:

Fax:

E-mail:

Signature Date:

that could be of Document Version 1.1 2020-10-30

RSP-100, Issue 12, August 2019 Modular Approval Attestation Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Innovation, Science and Economic Development Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: FCC / ISED Modular Approval Statement Grantee Code Equipment Product Code Check your GC here. Click Grantee Search. Check your CN here. FCC ID:

CN:

(Company Number) HVIN:

(Hardware Version Id. Number) HMN:

(Host Marketing Name) UPN:

(Unique Product Number) PMN:

(Product Marketing Name) FVIN:

(Firmware Version Id. Number) TO WHOM IT MAY CONCERN Pursuant to Paragraphs RSP-100, Issue 12 and CFR 15.212, we herewith declare for our module. Modular approval requirement

(a) The radio elements shall have the radio frequency circuitry shielded. Physical/discrete and tuning capacitors may be located external to the shield, but shall be on the module assembly. Yes No *

*Please provide a detailed explanation if the answer is No.:

(b) If the module has modulation/data input(s), they shall be buffered in order to ensure that the module will comply with the requirements set out in the applicable Radio Standards Specification (RSS) and Part 15 under conditions of excessive data rates or over-modulation.

*Please provide a detailed explanation if the answer is No.:

(c) The module shall have its own power supply regulation on the module itself. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host product that houses the module.

*Please provide a detailed explanation if the answer is No.:

(d) The module shall comply with the provisions for external power amplifiers and antennas detailed in the applicable RSS and rule part. The equipment certification application shall contain:

i. a detailed description of the configuration of highest antenna gain for each type of transmitting antenna for licence-exempt modules;

ii. the maximum transmitting antenna gain for licence modules; and iii. a detailed description of the configuration of lowest antenna gain for each type of receiving antenna for Dynamic Frequency Selection

(DFS) modules with removable antenna(s).

*Please provide a detailed explanation if the answer is No.:

Modular approval requirement

(e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration

(i.e. the module shall not be inside another product during testing). Yes No *

*Please provide a detailed explanation if the answer is No.:

(f) The module complies or will comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement (1.1307(b), 1.1310, 2.1091, and 2.1093) in its intended configuration/integration in a host.

*Please provide a detailed explanation if the answer is No.:

(g) The module must be labeled with its permanently affixed label (indicating ISED certification number, HVIN and FCC identifier), or use an electronic display (see KDB Publication 784748 and RSP-100, section 5).

*Please provide a detailed explanation if the answer is No.:

(h) The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee.

*Please provide a detailed explanation if the answer is No.:

(i) (Only applicable for FCC) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). For further information concerning antenna connectors see: DA-00-1087.

*Please provide a detailed explanation if the answer is No.:

If you have any questions, please feel free to contact us at the address shown below Best regards, Company Name:

Company Address:

Contact Name:

Signature:

Phone:

Fax:

E-mail:

Signature Date:

INFO for applicant: Limited Modolar Approval (LMA) may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specificmanufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured. Document Version 2.1 2020-10-30