FCC ID: PD98260NG Intel Dual Band Wireless-AC 8260

Lenovo YOGA 710 Regulatory Notice Lenovo regulatory notice for wireless adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

This manual contains regulatory information for the following Lenovo product:

Lenovo YOGA 710-14ISK

Lenovo YOGA 710-15ISK

Lenovo YOGA 710-14IKB

Lenovo YOGA 710-15IKB The following wireless modules are supported on Lenovo YOGA 710-14ISK/Lenovo YOGA 710-15ISK/Lenovo YOGA 710-14IKB/Lenovo YOGA 710-15IKB:

8260NGW

BCM94350ZAE Read first regulatory information Please read this document before you use your Lenovo computer. Your Lenovo computer complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. You must install and use your computer in strict accordance with the instructions as described hereafter. Veuillez lire ce document avant dutiliser votre ordinateur Lenovo. Votre ordinateur Lenovo est conforme aux normes de scurit et de radiofrquence du pays ou de la rgion o son utilisation sans fil est approuve. Vous devez installer et utiliser votre ordinateur en respectant scrupuleusement les instructions dcrites ci-aprs. 1 USA Federal Communications Commission (FCC) I. Factory preinstalled Wireless LAN + Bluetooth Combo module

FCC ID: PD98260NGU (Model: 8260NGW)

FCC ID: QDS-BRCM1087 (Model: BCM94350ZAE) i) The FCC RF Exposure compliance:

The radiated output power of the Wireless LAN + Bluetooth Combo Mini PCI Express Card authorized to use for the your Lenovo computer is far below the FCC radio frequency exposure limits. Nevertheless, it shall be used in such a manner that the potential for human contact during normal operation is minimized as follows:

Caution: The total radiated energy from the antennas connected to the installed wireless LAN module, conforms to the FCC limit of the SAR (Specific Absorption Rate) requirement, regarding 47 CFR Part 2 section 1093, when the computer was tested in either conventional notebook or tablet computer orientations. ii) FCC ID of wireless module:

On the bottom side of your Lenovo computer, you will find an indicator label of the format Contains Transmitter Module: FCC ID XXXX, where XXXX represents the FCC ID that corresponds to your preinstalled Wireless LAN + Bluetooth Combo module. iii) Radio Frequency interference requirement:

Each device has been tested and found to comply with the limits for a Class B digital device pursuant to FCC Part 15 Subpart B. Refer to Electronic emission notices on page 5. When you use a Wireless LAN + Bluetooth Combo module in the 802.11 a/n transmission mode:

High power radars are allocated as primary users of the 5250 to 5350 MHz and 5650 to 5850 MHz bands. These radar stations can cause interference with and/or damage this device. II. Simultaneous use of RF transmitters Make sure of the following conditions on use of wireless features:

1. When you use any other RF option device, all wireless features in your Lenovo computer are required to be turned off. 2. Users must follow the RF Safety instructions on wireless option devices that are included in the RF option device's user's manual. 2 Canada Industry Canada (IC) IC Certification number I) Factory preinstalled Wireless LAN + Bluetooth Combo modules:

IC: 1000M-8260NG (Model: 8260NGW)

IC: 4324A-BRCM1087 (Model: BCM94350ZAE) There is no certification number of Industry Canada for Mini PCI Express Card shown on the enclosure of your Lenovo computer. Instead you will find an indicator label pointing to the location of the IC Certification number on the bottom side of your Lenovo computer. This label will be of the format Contains Transmitter Module: Canada IC: XXXX, where XXXX represents the IC ID that corresponds to your preinstalled WLAN module. II) Low power license-exempt radiocommunication devices (RSS-247):

Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. The transmitter devices have been designed to operate with the antennas integrated in Lenovo computer, and having a maximum gain of within 3 dBi. When you use a Wireless LAN and Bluetooth Combo module adapter in the 802.11 a/n transmission mode:

The devices for the band 5150-5350 MHz are only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz bands and these radars could cause interference and/or damage to LE-LAN (Licence-Exempt Local Area Network) devices.

The maximum antenna gain permitted for devices in the 5250-5350 MHz, 5470-5725 MHz, and 5725-5825 MHz bands complies with the e.i.r.p. limit. III) Exposure of humans to RF fields (RSS-102):

Lenovo computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canadas Web site at www.hc-sc.gc.ca/rpb The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 5, Section 4. 3 Numro dhomologation IC I) Modules de rseaux local sans fil pr-install lusine:

IC: 1000M-8260NG (Model: 8260NGW)

IC: 4324A-BRCM1087 (Model: BCM94350ZAE) Le botier de votre ordinateur Lenovo ne comporte pas de numro dhomologation IC (Industry Canada) pour la carte mini-PCI Express ; mais sous votre Lenovo, vous trouverez une tiquette indicatrice pointant vers lemplacement du numro dhomologation IC. Ltiquette se prsente sous la forme Contains Transmitter Module: Canada IC: XXXX o XXXX reprsente lID IC qui correspond au module WLAN prinstall. II) Remarque relative aux appareils de communication radio de faible puissance sans licence (CNR-247):

Le fonctionnement de ce type dappareil est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas perturber les communications radio, et 2. cet appareil doit supporter toute perturbation, y compris les perturbations qui pourraient provoquer son dysfonctionnement. Les priphriques dmission sont conus pour fonctionner avec des antennes intgres aux Lenovo et ayant un gain maximal de moins de 3 dBi. Lorsque vous utilisez un module adaptateur LAN sans fil et Bluetooth Combo dans le 802,11 un mode de transmission / n :

Les dispositifs pour la bande 5150-5350 MHz ne sont que pour une utilisation en intrieur pour rduire potentiel d' interfrences nuisibles la co-canal systmes satellite mobile .

Les radars haute puissance sont dsigns comme utilisateurs principaux ( ce qui signifie qu'ils ont la priorit) des bandes 5250- 5350 MHz et 5650-5850 MHz et ces radars pourraient provoquer interfrences et / ou des dommages LE-LAN ( exempte de licence Local Area Network) appareils.

Le gain d'antenne maximal autoris pour les appareils dans les bandes de frquence 5250-5350 MHz, 5470-5725 MHz et 5725-5825 MHz est conforme la limite p.i.r.e

(puissance isotrope rayonne quivalente). III) Exposition des tres humains aux champs radiolectriques (RF) (CNR-102):

Lordinateur Lenovo utilise des antennes intgrales faible gain qui nmettent pas un champ lectromagntique suprieur aux normes imposes par le Ministre de la sant canadien pour la population. Consultez le Safety Code 6 sur le site Web du Ministre de la sant canadien ladresse www.hc-sc.gc.ca/rpb. L' nergie rayonne par les antennes connectes aux adaptateurs sans fil est conforme la IC limite de l'exigence de l'exposition aux RF IC concernant CNR- 102, Issue 5, Section 4. 4 Electronic emission notices Federal Communications Commission (FCC) Statement

Models: 8260NGW and BCM94350ZAE. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult an authorized dealer or service representative for help. Lenovo is not responsible for any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Lenovo (United States) Incorporated 1009 Think Place - Building One Morrisville, NC 27560 Telephone: 1-919-294-5900 Trademarks Lenovo and the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others. 5 L e n o v o C h n a i 2 0 1 6 Rev. AA00

Lenovo ideapad MIIX 510-12ISK User Guide Read the safety notices and important tips in the included manuals before using your computer. Notes Before using the product, be sure to read Lenovo Safety and General Information Guide rst. The latest electronic compliance and environmental information are available from the Lenovo compliance information Web sites.

- To view compliance information go to:

http://www.lenovo.com/compliance

- To download environmental information go to:

http://www.lenovo.com/ecodeclaration Some instructions in this guide may assume that you are using Windows 10. If you are using another Windows operating system, some operations may be slightly dierent. If you are using other operating systems, some operations may not apply to you. The features described in this guide are common to most models. Some features may not be available on your computer or your computer may include features that are not described in this user guide. The illustrations in this manual may dier from the actual product. The screenshots of operating system are for reference only. Please refer to the actual product. Regulatory Notice For details, refer to Guides & Manuals at http://support.lenovo.com. First Edition (July 2016) Copyright Lenovo 2016. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Contents Chapter 1. Getting to know your computer .................................................................................... 1 Front view...................................................................................................................................................... 1 Left-side view ................................................................................................................................................ 3 Right-side view ............................................................................................................................................. 4 Top View........................................................................................................................................................ 5 Bottom view................................................................................................................................................... 6 Rear view ....................................................................................................................................................... 7 To use the stand cover.................................................................................................................................. 8 Keyboard folio top view ............................................................................................................................ 10 Chapter 2. Starting to use Windows 10......................................................................................... 18 Configuring the operating system for the first time.............................................................................. 18 Operating system interfaces...................................................................................................................... 18 Putting the computer to sleep or shutting it down................................................................................ 21 Touch screen operation.............................................................................................................................. 23 Connecting to a wireless network ............................................................................................................ 26 Get help from Windows ............................................................................................................................ 27 Chapter 3. Recovery system .......................................................................................................... 28 Chapter 4. Troubleshooting............................................................................................................ 30 Frequently asked questions....................................................................................................................... 30 Troubleshooting.......................................................................................................................................... 31 Trademarks...................................................................................................................................... 34 i Chapter 1. Getting to know your computer Front view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2-2 2-2 2-1 2-1 3 a Front camera Use the camera for video communication or taking photos. b Wireless LAN antenna Connects to a wireless LAN adapter to send and receive wireless radio signals. Note: For Wi-Fi models, the WLAN antennas are located in located in 2-1 and 2-2

. 2-1

; For LTE models, the WLAN antennas are c Multi-touch screen Functions as the visual display as well as touch pad input. Note: For details, see Touch screen operation on page 23. 1 Chapter 1. Getting to know your computer

Screen orientation You can rotate the display panel to your preferred orientation. The orientation of the display automatically changes (alternating between portrait and landscape modes) depending on how you hold it. 2 Chapter 1. Getting to know your computer Left-side view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 32 4 5 2 a Speakers Provide audio output. b Digital array microphone Captures sound which can be used for video conferencing, voice narration, or audio recording. c AC power adapter jack Connects to the AC power adapter. d USB 3.0 port e Type-C port Connects to USB devices. Type-C port supports:

USB 3.0 Native display port 1.2 video output VGA/HDMI output using Type-C VGA/HDMI adapter (sold separately) 3 Chapter 1. Getting to know your computer Right-side view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 3 4 a Power button When the computer is off, press and hold this button to turn on the computer. b Volume up/down button Increases/decreases the volume level. c Combo audio jack Connects to headsets. Notes:

The combo audio jack does not support conventional microphones. The recording function might not be supported if third-party headphones or headsets are connected, due to different industry standards. d Speakers Provide audio output. 4 Chapter 1. Getting to know your computer Top View - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 a Ventilation slots Dissipate internal heat. Note: Make sure that none of the ventilation slots are blocked, or else overheating of the computer may occur. 5 Chapter 1. Getting to know your computer Bottom view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 a Pogo pin with guide pin Note: For details, see Combination of tablet and keyboard folio on page 12. 6 Chapter 1. Getting to know your computer Rear view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

21 2 2 3 3 a Rear camera b Stand cover Use the camera for video communication or taking photos. This stand cover can flip as required, allowing the tablet to stand at different angles. Note: Always keep the flip angle below 150. Be careful not to leave a pen or any other items between the stand cover and the bottom plate after closing the stand cover. Otherwise, it could be damaged. c Micro SD card slot Accepts a micro SD card (not supplied). 7 Chapter 1. Getting to know your computer To use the stand cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Lenovo ideapad MIIX 510-12ISK is equipped with a stand cover which can be flipped as preferred; to stand the tablet at different angles.

To flip the stand cover As shown by the arrow, flip the stand cover gently to the desired angle by inserting your finger in the finger recess between the stand cover and the bottom plate. 8 Chapter 1. Getting to know your computer Notes:

Do not use excessive force when flipping to avoid damage to the hinge. Always keep the flip angle below 150. Be careful not to leave a pen or any other items between the stand cover and the bottom plate after closing the stand cover. Otherwise, it could be damaged. 9 Chapter 1. Getting to know your computer Keyboard folio top view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 3 a Pogo pin with guide pin Connect the tablet to the keyboard Folio and secure it in the installation position. Note: For details, see Combination of tablet and keyboard folio on page 12. b Keyboard c Touch pad 10 Chapter 1. Getting to know your computer

Using the keyboard Hotkeys You can access certain system settings quickly by pressing the appropriate hotkeys.

:

:

:

:

:

:

Mutes/unmutes the sound. Decreases the volume level. Increases the volume level. Closes the currently active window. Refreshes the desktop or the currently active window. Enables/disables the touch pad.

:

:

:

:

:

:

Enables/disables Airplane mode. Displays all currently active apps. Open the web browser. Toggles the display between the computer and an external device. Decreases display brightness. Increases display brightness. 11 Chapter 1. Getting to know your computer

Combination of tablet and keyboard folio The Lenovo ideapad MIIX 510-12ISK is not only a tablet. It can be combined with a keyboard folio and used as a notebook computer. Attaching the tablet Align the connector of the keyboard folio with the tablet and then attach the tablet in the direction shown by the arrow. 12 Chapter 1. Getting to know your computer Note: Tablet-keyboard folio tongue has strong magnetic force, so as to easily connect with and secure the tablet. 13 Chapter 1. Getting to know your computer Placement mode of the tablet and the keyboard folio There are two placement modes of the tablet and the keyboard folio. You can select one as you desire. 14 Chapter 1. Getting to know your computer 15 Chapter 1. Getting to know your computer Detaching the tablet As shown by the arrow in Fig. it from the tablet. while carefully detaching the tablet in the direction shown by the arrow

, push both ends of the tablet-keyboard folio tongue to detach b a

. 1 1 16 Chapter 1. Getting to know your computer 2 Notes:

Be careful not to damage the connector when attaching or detaching the tablet. The illustrations above are for reference only, please refer to the actual product. 17 Chapter 2. Starting to use Windows 10 Configuring the operating system for the first time - - - - - - - - - - - -

You may need to configure the operating system when it is first used. The configuration process may include the procedures below:

Accepting the end user license agreement Configuring the Internet connection Registering the operating system Creating a user account Operating system interfaces - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The return of the Start menu Windows 10 comes with a powerful and useful start menu. To open the start menu, do one of the following:

Select the Start button in the lower-left corner, the Start menu is displayed. Press the Windows key on the keyboard. The power button is on the Start menu, select it you can choose to shut down or restart the computer, or put the computer into sleep mode. Through the Start menu, you can locate all the installed apps or view the frequently used apps. 18 Chapter 2. Starting to use Windows 10 The ACTION CENTER Select the ACTION CENTER icon on the taskbar and the ACTION CENTER is displayed. From the ACTION CENTER, you can examine important notifications from Windows and your apps. Moreover, you can change common settings quickly. Task View in taskbar In Windows 10, you can add a new desktop and switch between different desktops. To add a new desktop, do the following:

Select the Task View icon in the taskbar area. 19 Chapter 2. Starting to use Windows 10 Select New desktop. To switch between desktops, select the Task View icon Also, you can manage apps in the multi-tasking view:

a Select the Task View button to display all apps in use on the screen. b Select to enter the apps or close the apps.

, then select your desired desktop. 20 Chapter 2. Starting to use Windows 10 Putting the computer to sleep or shutting it down - - - - - - - - - - - - - -

When you have finished working with your computer, you can put it to sleep or shut it down.

Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following:

Press the Power button. Select the Start button, then select Power Sleep. Note: Put your computer to sleep before you move it. Moving your computer while the hard disk drive is spinning can damage the hard disk, causing loss of data. To wake the computer, do one of the following:

Press any key on the keyboard. Press the Power button. Press the Windows button. 21 Chapter 2. Starting to use Windows 10

Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down the computer, do one of the following:

Select the Start button, then select Power Shut down. Right-click or press the Start button in the lower-left corner and select Shut down or sign out Shut down. 22 Chapter 2. Starting to use Windows 10 Touch screen operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The display panel can accept inputs like a tablet, using the multi-touch screen, or like a traditional notebook computer, using the keyboard and touch pad.

Multi-touch gestures You can touch the screen with one or more fingertips to perform a variety of tasks. Frequently used gestures Tasks performed Tap Tap once on an item. Performs an action, such as starting an app, opening a link, or performing a command. Similar to left-clicking with a mouse. Press and hold Press your finger down and leave it there for a moment. Enables you to see detailed information before selecting an action. Can also open a menu with more options. Similar to right-

clicking with a mouse. 23 Chapter 2. Starting to use Windows 10

(continued) Frequently used gestures Tasks performed Zoom Move two fingers together or apart while touching the screen. Zooms in and out on visual apps, such as pictures and maps. Can also jump to the beginning or end of a list. Rotate Place two or more fingers on an item and then turn your hand. Rotates an object (Note: Not all items can be rotated, depending upon the app.). Slide Drag your finger across the screen. Pans or scrolls through lists and pages. Can also move an object or be used to draw or write, depending upon the app. Similar to pressing and holding to pan and to scrolling with a mouse. 24 Chapter 2. Starting to use Windows 10

(continued) Frequently used gestures Tasks performed Swipe Start from any edge of the screen, then swipe inwards toward the center. Swiping in from the left edge can:

Bring in and open an app currently running in the background. Swipe from the right edge can open the ACTION CENTER. 25 Chapter 2. Starting to use Windows 10 Connecting to a wireless network - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Enabling wireless connection To confirm that Airplane mode is disabled, go to the desktop and check the notification area. If you see the wireless function is enabled. icon displayed on the lower right, then Airplane mode is on. Otherwise, Note: Airplane mode is disabled by default. If Airplane mode is on, do one of the following to enable the wireless function:

Press Select the to disable Airplane mode (located on the keyboard). icon on the lower right corner of the notification area to open the network configuration page. Select Settings Network & Internet Airplane mode to open the network configuration page. Then toggle the airplane mode switch to Off. Connecting to a wireless network After wireless has been enabled, the computer will scan for available wireless networks and display them in the wireless network list. To connect to a wireless network, click the network name in the list, and then click Connect. Note: Some networks require a network security key or passphrase for connection. To connect to one of those networks, ask the network administrator or the Internet Service Provider (ISP) for the security key or passphrase. 26 Chapter 2. Starting to use Windows 10 Get help from Windows - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

If you have a problem with the operating system, see the Windows Get Started app. To open it, do the following:

Select the Start button, then select Get Started from All apps. 27 Chapter 3. Recovery system

Introduction Reset this PC is a built-in recovery tool that enables users to restore their operating system to its original state. This preserves their data and important customizations, without the need to back up their data in advance. The following Reset this PC features are available to users from multiple locations within Windows:

keep my files Fixes software problems by reinstalling the factory default configuration. This preserves the personal files, and deletes apps and settings. Remove everything Prepares the computer for recycling or transfer of ownership. This reinstalls the factory default configuration and returns all user data and applications to the state of their original Out-of-Box Experience (OOBE).

Using Reset this PC Reset this PC can be launched using one of the following methods:

Power button + Volume up button:

- Shut down the computer and wait at least five seconds.

- Press and hold the volume up button and then press the Power button, until the Novo Menu appears on the screen.

- Novo menu System Recovery Troubleshoot Reset this PC Windows PC settings:

- Windows PC settings Update&security Recovery Reset this PC select Start. For more instructions, see the Windows Help and Support file on your computer. When I purchased my computer, it included a copy of Windows. How can I determine whether the copy of Windows is preinstalled by Lenovo?

On the outside of the sales package of your computer, you should find a label containing configuration information for your computer. Check the printed string next to OS. If it contains Windows or WIN, the copy of Windows was preinstalled by Lenovo. What is the Recovery Partition?

If your computer is preinstalled with any version of Windows 10, the storage device of your computer contains a Recovery Partition. This partition contains the image file of the preinstalled Windows operating system. In cases of system failure, you can use the Lenovo OneKey Recovery system or the Windows Reset feature to restore the operating system to its factory status. Note: The Recovery Partition is not assigned a drive letter and cannot be accessed through Windows File Explorer. 28 Chapter 3. Recovery system I uninstalled a preinstalled software, but there is no significant increase in the free drive space. The copy of Windows running on your computer may be Compact technology enabled. For computers with Compact technology enabled Windows, the majority of files needed for preinstalled software are installed on the Recovery Partition and wont be deleted through normal uninstallation. What happens if I attempt to delete or modify the Recovery Partition?

Attention:

Do not delete or modify the Recovery Partition on a Compact technology enabled computer. If the Recovery Partition is deleted or modified, you may not be able to restore Windows to the factory status. For computer models on which Compact technology is enabled, deleting the Recovery Partition may cause Windows to fail to start. How can I determine whether the Windows running on my computer is Compact technology enabled?

Compact technology is normally enabled on copies of Windows 10 Update running on SSD (or eMMC) -only computer models. To check your computer, a Right-click the Start button in the lower-left corner and select Disk Management. b The Disk Management program starts. If Wim Boot is labeled on the Windows partition (as illustrated), Compact technology is enabled on your copy of Windows. 29 Chapter 4. Troubleshooting Frequently asked questions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

This section lists frequently asked questions by category.

Finding information What safety precautions should I follow when using my computer?

The Lenovo Safety and General Information Guide which came with your computer contains safety precautions for using your computer. Read and follow all precautions during use. Where can I find the hardware specifications for my computer?

You can find hardware specifications for your computer on the printed flyers which came with your computer. Where can I find warranty information?

For detailed warranty information on this machine, please visit below website to check out:

support.lenovo.com/warrantystatus.

Drivers Where can I find drivers for the various hardware devices of my computer?

You can download the latest device drivers from the Lenovo consumer support website.

Getting help How can I contact the customer support center?

See Chapter 3. Getting help and service in the Lenovo Safety and General Information Guide. 30 Chapter 4. Troubleshooting Troubleshooting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

If you do not find your problem here, see Chapter 1. The following section only describes problems that might negate the need to refer to the more comprehensive information in Chapter 1. Display problems When I turn on the computer, nothing appears on the screen. The screen goes blank while the computer is on. Sleep problems The critical low-battery error message appears, and the computer immediately turns off. The computer enters sleep mode immediately after Power-on. If the screen is blank, make sure that:

- The AC power adapter is connected to the computer and the power cord is plugged into a working electrical outlet.

- The computer power is on. Press and hold the Power button for about three seconds for confirmation.

- Press and hold the Power button for about ten seconds to force shut down the computer. Then press the Power button for about three seconds to restart. If these items are set correctly and the screen remains blank, have the computer serviced. Your power management is enabled. Do one of the following to resume from sleep mode:

- Press any key on the keyboard.

- Press the Power button. The battery power is getting low. Connect the AC power adapter to the computer. Make sure that:

- The battery is charged.

- The operating temperature is within the acceptable range. See Chapter 2. Use and care Information in the Lenovo Safety and General Information Guide. Note: If the battery is charged and the temperature is within range, do the following:

a Press the Power button for about three seconds to turn on the computer. b Press and hold the Power button for about ten seconds to force shut down. c Press the Power button for about three seconds again to restart. Then reset the computer with the Reset this PC recovery system. If the problem persists, have the computer serviced. 31 Chapter 4. Troubleshooting The computer does not return from sleep mode and the computer does not work. If the computer does not return from sleep mode, it might be because the battery is depleted. If your computer is in sleep mode, connect the AC power adapter to the computer. Then press the Power button. If your computer is powered-off, connect the AC power adapter to the computer. Then press the Power button to resume operation. Note: If the system still does not return from sleep mode, your system has stopped responding, and you cannot turn off the computer; force shut down the computer (Unsaved data may be lost). To force shut down the computer, press and hold the Power button for about ten seconds or more. Display panel problems The screen is blank. Do the following:

- If you are using the AC power adapter or the battery, press F12 (located on the keyboard) to make the screen brighter.

- Press the Power button to confirm if the computer is in sleep mode.

- If the problem persists, follow the solution in the next problem The screen is unreadable or distorted. Make sure that the screen resolution and color quality are correctly set. Is the operating system or programs installed correctly?

If they are installed and configured correctly, do the following:

a Press the Power button for about three seconds to turn on the computer. The screen is unreadable or distorted. Incorrect characters appear on the screen. b Press and hold the Power button for about ten seconds to force shut down. c Press the Power button for about three seconds again to restart. Then reset the computer with the Reset this PC recovery system. If the problem persists, have the computer serviced. Sound problems No sound can be heard from the speakers even when the volume is turned up. Make sure that:

- The Mute function is off.

- The combo audio jack is not being used.

- Speakers are selected as the playback device. 32 Chapter 4. Troubleshooting Recharge the battery. For details, see Recovery system on page 28. Battery problems Your computer shuts down before the battery status icon shows it is empty.

-or-

Your computer operates after the battery status icon shows it is empty. A startup problem The Microsoft Windows operating system does not start. Recovery System problems Failure to restore system partition to factory default. The system partition (e.g. the partition size or the drive capacity of C) has been modified. Other problems Your computer does not respond. To turn off your computer, press and hold the Power button for about ten seconds or more. 33 Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo ideapad Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. 34 L e n o v o C h n a 2 0 1 6 i en-US Rev. AA00

Lenovo ideapad MIIX 700-12ISK Regulatory Notice Lenovo regulatory notice for wireless adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

This manual contains regulatory information for the following Lenovo products:

Lenovo ideapad MIIX 700-12ISK The following wireless modules are supported on Lenovo ideapad MIIX 700-12ISK:

BCM94350ZAE

8260NGW

Read first regulatory information Please read this document before you use the Lenovo computer. Lenovo computer complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. You must install and use your computer in strict accordance with the instructions as described hereafter. Veuillez lire ce document avant dutiliser lordinateur Lenovo. Lordinateur Lenovo est conforme aux normes de scurit et de radiofrquence du pays ou de la rgion o son utilisation sans fil est agre. Vous devez installer et utiliser votre ordinateur en respectant scrupuleusement les instructions dcrites ci-aprs. 1

USA Federal Communications Commission (FCC) I. Factory preinstalled Wireless LAN + Bluetooth Combo module

FCC ID: QDS-BRCM1087 (Model: BCM94350ZAE)

FCC ID: PD98260NG (Model: 8260NGW) Wireless LAN + Bluetooth Combo Mini PCI Express Cards marketed in the USA and Canada do not support nor function in the extended channels (12ch, 13ch). i) The FCC RF Exposure compliance:

The radiated output power of the Wireless LAN + Bluetooth Combo Mini PCI Express Card authorized to use for the your Lenovo computer is far below the FCC radio frequency exposure limits. Nevertheless, it shall be used in such a manner that the potential for human contact during normal operation is minimized as follows:

Caution: To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm (8 inches) must be maintained between the antennas connected to the wireless module and all persons. If the distance may not be maintained while the computer display is closed, you must set sleep as the power mode when closing the display. ii) FCC ID of wireless module:

On the bottom side of your Lenovo computer, you will find an indicator label of the format Contains Transmitter Module: FCC ID XXXX, where XXXX represents the FCC ID that corresponds to your preinstalled Wireless LAN + Bluetooth Combo module. iii) Radio Frequency interference requirement:

Each device has been tested and found to comply with the limits for a Class B digital device pursuant to FCC Part 15 Subpart B. Refer to Electronic emission notices on page 5. When you use a Wireless LAN + Bluetooth Combo module in the 802.11 a/n transmission mode:

High power radars are allocated as primary users of the 5250 to 5350 MHz and 5650 to 5850 MHz bands. These radar stations can cause interference with and/or damage this device. II. Simultaneous use of RF transmitters Make sure of the following conditions on use of wireless features:

1. When you use any other RF option device, all wireless features in your Lenovo computer are required to be turned off. 2. Users must follow the RF Safety instructions on wireless option devices that are included in the RF option devices users manual. 2

Canada Industry Canada (IC) IC Certification number I) Factory preinstalled Wireless LAN + Bluetooth Combo modules:

IC: 4324A-BRCM1087 (Model: BCM94350ZAE)

IC: 1000M-8260NG (Model: 8260NGW) Wireless LAN + Bluetooth Combo Mini PCI Express Cards marketed in the USA and Canada do not support nor function in the extended channels (12ch, 13ch). There is no certification number of Industry Canada for Mini PCI Express Card shown on the enclosure of your Lenovo computer. Instead you will find an indicator label pointing to the location of the IC Certification number on the bottom side of your Lenovo computer. This label will be of the format Contains Transmitter Module: Canada IC: XXXX, where XXXX represents the IC ID that corresponds to your preinstalled WLAN module. II) Low power license-exempt radiocommunication devices (RSS-247):

When you use a Wireless LAN and Bluetooth Combo module adapter in the 802.11 a/n transmission mode:

The devices for the band 5150-5350 MHz are only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they have priority) of 5250-

5350 MHz and 5650-5850 MHz bands and these radars could cause interference and/or damage to LE-LAN (Licence-Exempt Local Area Network) devices.

The maximum antenna gain permitted for devices in the 5250-5350 MHz, 5470-

5725 MHz, and 5725-5825 MHz bands complies with the e.i.r.p. limit. III) Exposure of humans to RF fields (RSS-102):

Lenovo computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canadas Web site at www.hc-sc.gc.ca/rpb The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 5, Section 4. When you use a Wireless LAN and Bluetooth Combo module adapter in the 802.11 a/n transmission mode:

The devices for the band 5150-5350 MHz are only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz bands and these radars could cause interference and/or damage to LE-LAN (Licence-Exempt Local Area Network) devices. 3 Numro dhomologation IC I) Modules de rseaux local sans fil pr-install lusine:

IC: 4324A-BRCM1087 (Model: BCM94350ZAE)

IC: 1000M-8260NG (Model: 8260NGW) Les cartes de rseau local sans fil Express mini-PCI commercialises aux Etats-Unis et au Canada ne prennent pas en charge les canaux tendus (12ch, 13ch) et ne fonctionnent donc pas sur de tels canaux. Le botier de votre ordinateur Lenovo ne comporte pas de numro dhomologation IC (Industry Canada) pour la carte mini-PCI Express ; mais sous votre Lenovo, vous trouverez une tiquette indicatrice pointant vers lemplacement du numro dhomologation IC. Ltiquette se prsente sous la forme Contains Transmitter Module: Canada IC: XXXX o XXXX reprsente lID IC qui correspond au module WLAN prinstall. II) Remarque relative aux appareils de communication radio de faible puissance sans licence (CNR-247):

Lorsque vous utilisez un module adaptateur LAN sans fil et Bluetooth Combo dans le 802,11 un mode de transmission / n :

Les dispositifs pour la bande 5150-5350 MHz ne sont que pour une utilisation en intrieur pour rduire potentiel dinterfrences nuisibles la co-canal systmes satellite mobile.

Les radars haute puissance sont dsigns comme utilisateurs principaux ( ce qui signifie quils ont la priorit) des bandes 5250- 5350 MHz et 5650-5850 MHz et ces radars pourraient provoquer interfrences et / ou des dommages LE-LAN ( exempte de licence Local Area Network) appareils.

Le gain dantenne maximal autoris pour les appareils dans les bandes de frquence 5250-5350 MHz, 5470-5725 MHz et 5725-5825 MHz est conforme la limite p.i.r.e

(puissance isotrope rayonne quivalente). III) Exposition des tres humains aux champs radiolectriques (RF) (CNR-102):

Lordinateur Lenovo utilise des antennes intgrales faible gain qui nmettent pas un champ lectromagntique suprieur aux normes imposes par le Ministre de la sant canadien pour la population. Consultez le Safety Code 6 sur le site Web du Ministre de la sant canadien ladresse www.hc-sc.gc.ca/rpb. Lnergie rayonne par les antennes connectes aux adaptateurs sans fil est conforme la IC limite de lexigence de lexposition aux RF IC concernant CNR- 102, Issue 5, Section 4. 4

Electronic emission notices Federal Communications Commission (FCC) Statement

Models: BCM94350ZAE, 8260NGW This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult an authorized dealer or service representative for help. Lenovo is not responsible for any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Lenovo (United States) Incorporated 1009 Think Place - Building One Morrisville, NC 27560 Telephone: 1-919-294-5900 Trademarks Lenovo and the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others. 5 L e n o v o C h n a i 2 0 1 5 Rev. AA00

Lenovo YOGA 710 Lenovo YOGA 710-14ISK Lenovo YOGA 710-15ISK User Guide Read the safety notices and important tips in the included manuals before using your computer. Notes Before using the product, be sure to read Lenovo Safety and General Information Guide first. Some instructions in this guide may assume that you are using Windows 10. If you are using another Windows operating system, some operations may be slightly different. If you are using other operating systems, some operations may not apply to you. The features described in this guide are common to most models. Some features may not be available on your computer or your computer may include features that are not described in this user guide. The illustrations used in this manual are for Lenovo YOGA 710-15ISK unless otherwise stated. The illustrations in this manual may differ from the actual product. Please refer to the actual product. Regulatory Notice For details, refer to Guides & Manuals at http://support.lenovo.com. First Edition (January 2016) Copyright Lenovo 2016. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Contents Chapter 1. Getting to know your computer ......................................... 1 Top view ..................................................................................................................... 1 Left-side view ............................................................................................................ 9 Right-side view ........................................................................................................ 12 Bottom view ............................................................................................................. 15 Chapter 2. Starting to use Windows 10 ............................................. 16 Configuring the operating system for the first time ........................................... 16 Operating system interfaces ................................................................................... 16 Putting the computer to sleep or shutting it down ............................................. 18 Task and desktop management ............................................................................. 20 Connecting to a wireless network ......................................................................... 21 Get Started app......................................................................................................... 21 Touch screen operation ........................................................................................... 22 Chapter 3. Lenovo OneKey Recovery system .................................. 25 Chapter 4. Troubleshooting ................................................................ 27 Frequently asked questions ................................................................................... 27 Troubleshooting ...................................................................................................... 29 Trademarks ........................................................................................... 32 i Chapter 1. Getting to know your computer Top view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Lenovo YOGA 710-14ISK 1 2 3 4 5 1 Chapter 1. Getting to know your computer Lenovo YOGA 710-15ISK 1 2 3 4 5 Note: The dashed areas indicate parts that are not visible externally. Attention:

When closing the display panel, be careful not to leave pens or any other objects in between the display panel and the keyboard. Otherwise, the display panel may be damaged. 2 a Integrated camera b Multi-touch screen c Built-in microphones d Wireless LAN antennas e Touch pad Chapter 1. Getting to know your computer Use the camera for video communication. The LCD display with LED backlight provides brilliant visual output. Multi-touch function is available on this display. Capture sound which can be used for video conferencing, voice narration, or audio recording. Connect to a wireless LAN adapter to send and receive wireless radio signals. The touch pad functions as a conventional mouse. Touch pad: To move the pointer on the screen, slide your fingertip over the pad in the direction in which you want the pointer to move. Touch pad buttons: The functions of the left/right side correspond to those of the left/right mouse button on a conventional mouse. Note: You can enable/disable the touch pad by pressing F6 (

). 3 Chapter 1. Getting to know your computer Using the keyboard Hotkeys You can access certain system settings quickly by pressing the appropriate hotkeys.

: Mutes/unmutes the sound. Decreases the volume level. Increases the volume level. Closes the currently active window. Refreshes the desktop or the currently active window. Enables/disables the touch pad.

:

:

:

:

:

:

Enables/disables Airplane mode.

: Displays all currently active apps. Turns on/off the backlight of the LCD screen. Toggles the display between the computer and an external device.

:

:

: Decreases display brightness.

:

Increases display brightness. Note: If you changed the Hotkey Mode from Enabled to Disabled in the BIOS setup utility, you will need to press the Fn key in combination with the appropriate hotkey. 4 Chapter 1. Getting to know your computer Function key combinations Through the use of the function keys, you can change operational features instantly. To use this function, press and hold Fn a; then press one of the function keys b. b a b b The following describes the features of each function key. Fn + Esc:

Fn + Home:

Fn + End:

Fn + PgUp:

Fn + PgDn:

Fn + Space

(on select models):

Switches to paper display mode. Activate the pause function. Activate the break function. Enable/Disable the scroll lock. Activate the insert function. Turn on/off the keyboard backlight. 5 Chapter 1. Getting to know your computer Positioning the display panel The display panel can be opened to any angle up to 360 degrees. Notebook Mode Suitable for tasks that require a keyboard and mouse (such as creating documents, writing e-mails, and so on). 6 Chapter 1. Getting to know your computer Stand Mode (Theater Mode) Suitable for tasks that require little or no touch (such as viewing photos or playing videos). Tablet Mode Suitable for tasks that require touching the screen often (such as surfing the Web, playing games, and so on). 7 Chapter 1. Getting to know your computer Tent Mode (Presentation Mode) Suitable for tasks that require limited interaction with the touch screen (such as displaying graphs or PowerPoint presentations). Attention:

Do not open the display with too much force, otherwise the panel or hinges may be damaged. Note: The keyboard and touch pad are automatically locked when the screen is opened beyond 190 degrees (approximately). 8 Chapter 1. Getting to know your computer Left-side view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 3 4 5 a AC power adapter jack Connects to the AC power adapter. b Battery status indicator Indicator Battery status indicator Indicator status On (solid white) Solid amber Fast blinking amber Slow blinking amber Slow blinking white Meaning The battery has more than 20% charge. The battery has between 5% and 20%

charge. The battery has less than 5% charge. The battery is being charged. When battery charge reaches 20%, the blinking color changes to white. The battery has between 20% and 80%

charge and is still charging. When the battery reaches 80% charge the light will stop blinking, but charging will continue until the battery is fully charged. 9 Chapter 1. Getting to know your computer c Memory card slot Insert memory cards (not supplied) here. Note: For details, see Using memory cards (not supplied) on page 11. d Combo audio jack Connects to headsets. Notes:

The combo audio jack does not support conventional microphones. The recording function may not be supported if third-party headphones or headsets are connected, due to different industry standards. e Novo button When the computer is off, press this button to start the Lenovo OneKey Recovery system or the BIOS setup utility, or to enter the boot menu. Notes:

You can use the tip of an unfolded paper clip (or similar object without a sharp tip) to gently press the Novo button. For details, see Lenovo OneKey Recovery system on page 25. 10 Chapter 1. Getting to know your computer Using memory cards (not supplied) Your computer supports the following types of memory cards:

Secure Digital (SD) card

Secure Digital High Capacity (SDHC) card

SD eXtended Capacity (SDXC) card

MultiMediaCard (MMC) Notes:

This card reader does not support SDIO devices (e.g., SDIO Bluetooth, etc.). Insert only one card in the slot at a time. Inserting a memory card Insert the memory card until it touches the bottom of the slot. Removing a memory card Gently pull the memory card out of the memory card slot. Note: Before removing the memory card, disable it by using the Windows safely remove hardware and eject media utility to avoid data corruption. 11 Chapter 1. Getting to know your computer Right-side view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 3 4 a Power status indicator Indicator Power status indicator Indicator status On (solid white) Blinking Off Meaning The computer is powered on. The computer is in sleep mode. The computer is powered off. b Power button c Micro HDMI port d USB ports Press this button to turn on the computer. Connects to devices with micro HDMI input such as a TV or an external display. Connect to USB devices. Note: For details, see Connecting USB devices on page 13. 12 Chapter 1. Getting to know your computer Connecting USB devices You can connect a USB device to your computer by inserting its USB plug

(Type A) into the USB port on your computer. The first time you plug a USB device into a particular USB port on your computer, Windows automatically installs a driver for that device. After the driver has been installed, you can disconnect and reconnect the device without performing any additional steps. Note: Typically, Windows detects a new device after it has been connected, and then installs the driver automatically. However, some devices may require you to install the driver before connecting. Check the documentation provided by the devices manufacturer before connecting the device. Before disconnecting a USB storage device, make sure your computer has finished transferring data to that device. Click the Safely Remove Hardware and Eject Media icon in the Windows notification area to remove the device before disconnecting. Note: If your USB device uses a power cord, connect the device to a power source before connecting it. Otherwise, the device may not be recognized. 13 Chapter 1. Getting to know your computer Screen orientation You can rotate the display panel to your preferred orientation.

The orientation of the display automatically changes (alternating between portrait and landscape modes) depending upon how you hold the computer. Portrait Landscape 14 Chapter 1. Getting to know your computer Bottom view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 a Ventilation slots b Speakers Allow air to enter the computer for cooling. Provide audio output. 2 15 Chapter 2. Starting to use Windows 10 Configuring the operating system for the first time - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

You may need to configure the operating system when it is first used. The configuration process may include the procedures below:

Accepting the end user license agreement

Configuring the Internet connection

Registering the operating system

Creating a user account Operating system interfaces - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Windows 10 comes with a powerful and useful start menu. To open the start menu, do one of the following:

Press the Windows button

.

Press the Windows key

Select Start on the lower-left corner of the desktop. on the keyboard. 1 2 3 4 5 6 7 a Get Started app b Settings button c Power button d All apps button e Start button f Search box g Task view button 16 Chapter 2. Starting to use Windows 10 Settings Settings lets you perform basic tasks. You can also search for more settings with the settings search box in the upper-right corner. To open the settings, do the following:

Open the start menu, and then select Settings

. Personalize the start menu You can personalize the start menu with your favorite apps. To personalize the start menu, do the following:

1 Open the start menu, and then select All apps to display the apps list. 2 Right click the app you want to add to the start menu, and then select Pin to Start. Note: You can also drag apps from the Most used or All apps columns to add them to the start menu. 17 Chapter 2. Starting to use Windows 10 Putting the computer to sleep or shutting it down - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

When you have finished working with your computer, you can put it to sleep or shut it down. Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following:

Close the display lid.

Press the Power button.

Open the start menu, and then select Power Sleep. Note: Wait until the power indicator light starts blinking (indicating that the computer is in sleep mode) before you move your computer. Moving your computer while the hard disk is spinning can damage the hard disk, causing loss of data. To wake the computer, do one of the following:

Press any key on the keyboard. (Notebook mode only)

Press the Power button.

Press the Windows button

. 18 Chapter 2. Starting to use Windows 10 Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down the computer, do one of the following:

Open the start menu, and then select Power Shut down.

Press and hold or right-click the Start button in the lower-left corner and select Shut down or sign out Shut down. 19 Chapter 2. Starting to use Windows 10 Task and desktop management - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Task view To open the task view, do one of the following:

Select the Task view button on the task bar.

Press the Windows key

Swiping in from the left edge of the screen.

+ Tab. Virtual desktop management Windows 10 supports the ability to create, manage and switch between virtual desktops. To create a new virtual desktop, do one of the following:

Open the task view, and then select New desktop.

Press the Windows key To switch between different desktops, do one of the following:

Open the task view and select the desktop you want active.

Press the Windows key to scroll through the desktops

+ Ctrl + D.

+ Ctrl +

/

youve created. 20 Chapter 2. Starting to use Windows 10 Connecting to a wireless network - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Enabling wireless connection To enable wireless functions, do the following:

1 Press F7 (

2 Click configuration page.

) to disable airplane mode. on the lower-right corner of the task bar to open the network Connecting to a wireless network After wireless has been enabled, the computer will automatically scan for available wireless networks and display them in the wireless network list. To connect to a wireless network, click the network name in the list, and then click Connect. Note: Some networks require a network security key or passphrase for connection. To connect to one of those networks, ask the network administrator or the Internet service provider

(ISP) for the security key or passphrase. Get Started app - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Windows 10 also provides the Get Started app to explain the new features of Windows 10. You can find it on the start menu. To open the Get Started app, do one of the following:

Open the start menu and select Get Started

Press Fn + F1 (depending on your keyboard layout). 21 Chapter 2. Starting to use Windows 10 Touch screen operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The display panel can accept inputs like a tablet, using the multi-touch screen, or like a traditional notebook computer, using the keyboard and touchpad. Multi-touch gestures You can touch the screen with one or more fingertips to perform a variety of tasks. Frequently used gestures Tasks performed Tap Tap once on an item. Performs an action, such as starting an app, opening a link, or performing a command. Similar to left-clicking with a mouse. Press and hold Press your finger down and leave it there for a moment. Enables you to see detailed information before selecting an action. Can also open a menu with more options. Similar to right-clicking with a mouse. 22 Chapter 2. Starting to use Windows 10

(continued) Frequently used gestures Tasks performed Zoom Move two fingers together or apart while touching the screen. Zooms in and out on visual apps, such as pictures and maps. Can also jump to the beginning or end of a list. Rotate Place two or more fingers on an item and then turn your hand. Rotates an object (Note: Not all items can be rotated, depending upon the app.). Slide Drag your finger across the screen. Pans or scrolls through lists and pages. Can also move an object or be used to draw or write, depending upon the app. Similar to pressing and holding to pan and to scrolling with a mouse. 23 Chapter 2. Starting to use Windows 10

(continued) Frequently used gestures Tasks performed Swipe Start from left/right edge of the screen, then swipe inwards toward the center. Swiping in from the left edge of the screen can open the task view. Swiping in from the right edge of the screen displays the action center. 24 Chapter 3. Lenovo OneKey Recovery system The Lenovo OneKey Recovery system is software designed to back up and restore your computer. You can use it to restore the system partition to its original status in case of a system failure. You can also create user backups for easy restoration as required. Notes:

If your computer is preinstalled with a GNU/Linux operating system, OneKey Recovery system is not available. To utilize the features of the OneKey Recovery system, your hard disk already includes a hidden partition by default to store the system image file and the OneKey Recovery system program files. This default partition is hidden for security reasons, which explains why the available disk space is less than the stated capacity. Backing up the system partition You can back up the system partition to an image file. This image file can be used to restore the system partition. To back up the system partition:

1 In Windows, press the Novo button or double-click OneKey Recovery icon to start the Lenovo OneKey Recovery system. 2 Click System Backup. 3 Select a back-up location and click Next to start the backup. Notes:

You can choose a back-up location on the local hard disk drive or an external storage device. Remove the removable hard disk drive before starting the Lenovo OneKey Recovery system. Otherwise, data from the removable hard disk drive might be lost. The back-up process may take a while. The back-up process is only available when Windows can be started normally. 25 Chapter 3. Lenovo OneKey Recovery system Restoring You can choose to restore the system partition to its original status or to a previously created back-up point. To restore the system partition:

1 In Windows, press the Novo button or double-click OneKey Recovery icon to start the Lenovo OneKey Recovery system. 2 Click System Recovery. The computer will restart to the recovery environment. 3 Follow the on-screen instructions to restore the system partition to its original status or to a previously created back-up point. Notes:

The recovery process is irreversible. Make sure to back up any data you wish to save on the system partition before starting the recovery process. The recovery process may take a while. So be sure to connect the AC power adapter to your computer during the recovery process. The above instructions should be followed when Windows can be started normally. If Windows cannot be started, then follow the steps below to start the Lenovo OneKey Recovery system:

1 Shut down the computer. 2 Press the Novo button. From the Novo Button Menu, select System recovery and press Enter. 26 Chapter 4. Troubleshooting Frequently asked questions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

This section lists frequently asked questions by category. Finding information What safety precautions should I follow when using my computer?

The Lenovo Safety and General Information Guide which came with your computer contains safety precautions for using your computer. Read and follow all the precautions when using your computer. Where can I find the hardware specifications for my computer?

You can find hardware specification for your computer on the printed flyers which came with your computer. Where can I find warranty information?

For detailed warranty information on this machine, please visit below website to check out: support.lenovo.com/warrantystatus. Drivers and preinstalled software Where are the installation discs for Lenovo preinstalled software (desktop software)?

Your computer did not come with installation discs for Lenovo preinstalled software. If you need to reinstall any preinstalled software, you can find the installation program on the C partition of your hard disk. If you cannot find the installation program there, you can also download it from the Lenovo consumer support website. Where can I find drivers for the various hardware devices of my computer?

If your computer is preinstalled with a Windows operating system, Lenovo provides drivers for all the hardware devices that you need on the C partition of your hard disk. You can also download the latest device drivers from the Lenovo consumer support website. 27 Chapter 4. Troubleshooting Lenovo OneKey Recovery system Where are the recovery discs?

Your computer did not come with recovery discs. Use the Lenovo OneKey Recovery system if you need to restore the system to its factory status. What can I do if the back-up process fails?

If you can start the backup but it fails during the back-up process, try the following steps:

1 Close all open programs, and then restart the back-up process. 2 Check to see if the destination media is damaged. Select another path and then try again. When do I need to restore the system to its factory status?

Use this feature when the operating system fails to start up. If there is critical data on the system partition, back it up before starting recovery. BIOS setup utility What is the BIOS setup utility?

The BIOS setup utility is ROM-based software. It displays basic computer information and provides options for setting boot devices, security, hardware mode, and other preferences. How can I start the BIOS setup utility?

To start the BIOS setup utility:

1 Shut down the computer. 2 Press the Novo button and then select BIOS Setup. Getting help How can I contact the customer support center?

See Chapter 3. Getting help and service in the Lenovo Safety and General Information Guide. 28 Chapter 4. Troubleshooting Troubleshooting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Display problems When I turn on the computer, nothing appears on the screen. When I turn on the computer, only a white cursor appears on a blank screen. The screen goes blank while the computer is on. Sleep problems The critical low-battery error message appears, and the computer immediately turns off. The computer enters sleep mode immediately after Power-on. If the screen is blank, make sure that:

- The AC power adapter is connected to the computer, and the power cord is plugged into a working electrical outlet.

- The computer power is on. Press the Power button again for confirmation. If these items are set correctly, and the screen remains blank, have the computer serviced. Restore backed-up files to your Windows environment or the entire contents of your hard disk to its original factory contents using the Lenovo OneKey Recovery system. If you still see only the cursor on the screen, have the computer serviced. Your power management is enabled. Do one of the following to resume from sleep mode:

- Press any key on the keyboard. (Notebook mode only)

- Press the Power button.

- Press the Windows button.

- Press F9 (

) to confirm whether the backlight of the LCD screen has been turned off. The battery power is getting low. Connect the AC power adapter to the computer. Make sure that:

- The battery is charged.

- The operating temperature is within the acceptable range. See Chapter 2. Use and care Information in the Lenovo Safety and General Information Guide. Note: If the battery is charged and the temperature is within range, have the computer serviced. 29 Chapter 4. Troubleshooting The computer does not return from sleep mode and the computer does not work. If your computer is in sleep mode, connect the AC power adapter to the computer, then press the Windows button or the Power button. If the system still does not return from sleep mode, your system has stopped responding, and you cannot turn off the computer; reset the computer. Unsaved data may be lost. To reset the computer, press and hold the Power button for eight seconds or more. If the computer still does not reset, remove the AC power adapter. Display panel problems The screen is blank. Do the following:

- If you are using the AC power adapter or the battery, and the battery status indicator is on, press F12 (

) to make the screen brighter.

- If the power indicator is blinking, press the Power button to resume from sleep mode.

- Press F9 (

) to confirm whether the backlight of the LCD screen has been turned off.

- If the problem persists, follow the solution in the next problem The screen is unreadable or distorted. Make sure that:

- The screen resolution and color quality are correctly set.

- The monitor type is correct. Is the operating system or programs installed correctly? If they are installed and configured correctly, have the computer serviced. The screen is unreadable or distorted. Incorrect characters appear on the screen. Sound problems No sound can be heard from the speakers even when the volume is turned up. Make sure that:

- The Mute function is off.

- The combo audio jack is not being used.

- Speakers are selected as the playback device. 30 Battery problems Your computer shuts down before the battery status indicator shows empty.

-or-

Your computer operates after the battery status indicator shows empty. Other problems Your computer does not respond. The connected external device does not work. Chapter 4. Troubleshooting Recharge the battery. To turn off your computer, press and hold the Power button for eight seconds or more. If the computer still does not respond, remove the AC power adapter. Your computer might lock when it enters sleep mode during a communication operation. Disable the sleep timer when you are working on the network. Do not connect or disconnect any external device cables other than USB while the computer power is on. Otherwise, you might damage your computer. When using high power consumption external devices, such as an external USB optical disk drive, use an external device power adapter. Otherwise, the device may not be recognized, or the system may shut down as a result. 31 Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo OneKey Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, products, or service names may be trademarks or service marks of others. 32 L e n o v o C h n a i 2 0 1 6 en-US Rev. AA00

May 19, 2015 Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA Subject: Model 8260NGW WLAN 802.11a/b/g/n/ac + BT 4.0 Adapter Card FCC ID: PD98260NG and PD98260NGU Gentlemen:

Please be advised that for the Model 8260NGW WiFi/Bluetooth card all final output power levels and operational parameters are programmed into the non-volatile memory (NVM) during the assembly process. The information programmed into the NVM is not accessible and cannot be changed by the end user/installer in any way. Since there are no end user/installer adjustments that can be made there is no tune-up procedure provided. If you have any questions please do not hesitate to contact me at your convenience. Sincerely, Steven C. Hackett Product Regulations Engineer Wireless Platforms R&D steven.c.hackett@intel.com Intel Corporation 100 Center Point Circle Columbia, SC 29210

Authority to Act as Agent May 19, 2015 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Quietek is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). Intel retains the rights to communicate or obtain information directly from ACB or AT4 Wireless at our discretion at any time regarding applications made on our behalf. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: May 19, 2016 By:

Title:

On behalf of: Intel Mobile Communications Telephone:

803-216-2344 Steven C. Hackett

(Print name) Wireless Regulations Engineer

(Company Name)

(Signature1) 100 Center Point Circle Columbia, SC 29210