Technical Specification
(TM03LNCAHK0) 1/13 History Ver. Date Contents 1.0 2016.12.16 Written Checked Approved by by by Note 2/13 Contents 1. Product Introduction..................................................................................................... 4 1.1 Block Diagram .................................................................................................... 5 1.2 Environmental Specifications .............................................................................. 5 1.3 Electrical Specifications ...................................................................................... 5 1.3.1 Absolute Maximum and ESD Ratings ........................................................... 5 1.3.2 Current Consumption ................................................................................... 6 1.4 Mechanical Specifications ................................................................................. 6 1.4.1 Physical Dimensions and Connection Interface ........................................... 6 1.4.2 Mechanical Drawing ..................................................................................... 7 2. Pin Definitions.............................................................................................................. 8 3 RF Specification ........................................................................................................... 9 3.1. LTE B4, B13 Specification ................................................................................. 9 3.2. WCDMA B2, B5 Specification.... 10 3/13 1. Product Introuction The TM03LNCAHK0 are designed for the automotive industry. They support LTE and CDMA air Interface standards. The TM03LNCAHK0 are based on the Qualcomm MDM9628 wireless chipsets and support the following bands. Table 1. Supported Band Region Canada LTE B2/B4/B5/B17 Band WCDMA B2/B5 1.1 Block Diagram Figure 1.1. TM03LNCAHK0 Block diagram 4/13 1.2 Environmental Specifications The environmental specification for operating and storage of the TM03LNCAHK0 are defined in the the table below. Table 2. Environmental Specifications Parameter Temperature Range Operating Temperature Storage Temperature Humidity 1.3 Electrical Specifications
-40 to 85
-40 to +90 95% or less This section provides details for some of the key electrical specifications of the TM03LNCAHK0 embedded modules. 1.3.1 Absolute Maximum Rating and ESD Ratings This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TM03LNCAHK0 embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter
+4.0_VPWR Power Supply Input VIN ESD Ratings ESD1) Voltage on any digital input or output pin Primary, Diversity antenna pads - Contact Min
-
-
Max 4.4V VREG_MDME+0.5 10 Units V V kV 1) The ESD Simulator configured with 330pF, 2000. Caution: The TM03LNCAHK0 embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TM03LNCAHK0 devices. 5/13 1.3.2 Current Consumption Table 4. TM03LNCAHK0 Current Consumption Mode LTE Parameter Band2, Max TX Output /Full RB Band4, Max TX Output /Full RB Band5, Max TX Output /Full RB Band17, Max TX Output /Full RB WCDMA Band2 Band5 LTE Idle, Registered WCDMA Idle, Registered LTE Sleep Mode, Average Current WCDMA Sleep Mode, Average Current 1.4 Mechanical Specifications 1.4.1 Physical Dimensions and Connection Interface Typical Max 650 600 Units 600 550 550 600 550 1.8 1.8 1.8 1.8 650 600 600 650 600 2.2 2.2 2.2 2.2 mA mA mA mA mA mA The TM03LNCAHK0 embedded modules are a Land Grid Array (LGA) form factor device. The device does not have a System or RF connectors. All electrical and mechanical connections are made via the 323 pad TM03LNCAHK0 on the underside of the PCB. Table5. TM03LNCAHK0 Embedded Module Dimensions Parameter Overall Dimension Overall Module Height PCB Thickness Flatness Specification Weight Nominal 34 x 40 3.5 1.0 TBD Max 34.35 x 40.35 3.85 1.1 0.1 Units mm mm mm mm g 6/13 1.4.2 Mechanical Drawing 1.4.2.1 Carrier PCB
[TOP View]
[Bottom View]
7/13 2. Pin Definitions Table6. PIN Definitions 8/13 3. RF Specification The specifications for the LTE and CDMA interfaces are defined. TM03LNCAHK0 is designed to be compliant with the standard shown in the table below. Table20. Standards Compliance Technology LTE WCDMA Standards 3GPP Release 8 3GPP Release 9 3.1 LTE B2, B4, B5, B17 Specification 3.1.1 LTE TX Output Power The Maximum / Minimum Transmitter Output Power of the TM03LNCAHK0 are specified in the following table. Table21. Conducted TX (Transmit) Max output Power Tolerances LTE Bands BAND Method (UL CH) Specification BAND2 UE Maximum Output Power BAND4 UE Maximum Output Power BAND5 UE Maximum Output Power BAND17 UE Maximum Output Power Measure Max and Min and Min Transmit Power of Low Channel (18650) Measure Max and Min Transmit Power of Mid Channel (18900) Measure Max and Min Transmit Power of High Channel (19150) Measure Max and Min and Min Transmit Power of Low Channel (20000) Measure Max and Min Transmit Power of Mid Channel (20175) Measure Max and Min Transmit Power of High Channel (20350) Measure Max and Min and Min Transmit Power of Low Channel (20450) Measure Max and Min Transmit Power of Mid Channel (20525) Measure Max and Min Transmit Power of High Channel (20600) Measure Max and Min and Min Transmit Power of Low Channel (23780) Measure Max and Min Transmit Power of Mid Channel (23790) Measure Max and Min Transmit Power of High Channel (23800) Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm 3.1.2 LTE RX Sensitivity The Receiver Sensitivity of the TM03LNCAHK0 are specified in the following table. 9/13 Table22. Conducted RX (Receive) Sensitivity LTE Bands BAND Method (DL CH) BAND2 Reference sensitivity level(DUAL) BAND4 Reference sensitivity level(DUAL) BAND5 Reference sensitivity level(DUAL) BAND17 Reference sensitivity level(DUAL) Measure BLER of Low Channel (650) Measure BLER of Mid Channel (900) Measure BLER of High Channel (1150) Measure BLER of Low Channel (2000) Measure BLER of Mid Channel (2175) Measure BLER of High Channel (2350) Measure BLER of Low Channel (2450) Measure BLER of Mid Channel (2525) Measure BLER of High Channel (2600) Measure BLER of Low Channel (5780) Measure BLER of Mid Channel (5790) Measure BLER of High Channel (5800) 3.2 WCDMA B2/B5 Specification 3.2.1 WCDMA TX Output Power Specification sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -97 BLER : 5%
sensitivity : -97 BLER : 5%
sensitivity : -97 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
sensitivity : -94 BLER : 5%
The Maximum Transmitter Output Power of the TM03LNCAHK0 are specified in the following table. Table23. Conducted TX (Transmit) Max output Power Tolerances WCDMA Bands Item Method (DL CH) Specification WCDMA B2 Power Level WCDMA B5 Power Level Measure Max Transmit Power of Low Channel
(CH= 10563) Measure Max Transmit Power of Middle Channel
(CH= 10700) Measure Max Transmit Power of High Channel
(CH= 10837) Measure Max Transmit Power of Low Channel
(CH=25) Measure Max Transmit Power of Middle Channel
(CH=600) Measure Max Transmit Power of High Channel
(CH=1175) Max Power : 20.3~25.7dBm Max Power : 20.3~25.7dBm Max Power : 20.3~25.7dBm Max Power : 20.3~25.7dBm Max Power : 20.3~25.7dBm Max Power : 20.3~25.7dBm 10/13 3.2.2 WCDMA RX Sensitivity The Receiver Sensitivity of the TM03LNCAHK0 are specified in the following table. Table24. Conducted RX (Receive) Sensitivity WCDMA Bands Item Method (DL CH) Measure BER of Low Channel (CH= 10563) WCDMA B2 Power Level Measure BER of Low Channel (CH= 10700) Measure BER of Low Channel (CH= 10837) Measure BER of Low Channel (CH=25) WCDMA B5 Power Level Measure BER of Low Channel (CH=600) Measure BER of Low Channel (CH=1175) Specification 0.1% @-106dBm 0.1% @-106dBm 0.1% @-106dBm 0.1% @-106dBm 0.1% @-106dBm 0.1% @-106dBm 11/13
<Warning Statements>
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. RF Exposure Statement The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be co-located or operating in conjunction with any other antenna or transmitter. The highest permitted antenna gains including cable loss for use with this device are: WCDMA850 :
0.89 dBi, WCDMA 1900 : 3.20 dBi, LTE Band 4: 2.41 dBi, LTE Band 2: 3.20 dBi, LTE Band 5: 0.89 dBi, LTE Band 17: -1.44 dBi End Product Labeling The module is labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: BEJGEN21CA Contains IC: 2703H-GEN21CA OEM Responsibilities to comply with FCC Regulations The module has been certified for integration into products only by OEM integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can t be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cant be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End UserThe OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. l'exposition aux RF Lantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. tiquetage du produit final Le module BT111 est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations suivantes :
Contient module metteur identification FCC ID : BEJGEN21CA Contient module metteur IC : 2703H-GEN21CA 12/13 RSS-GEN, Sec. 8.3 This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle sil fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal et limpdance requise pour chaque type dantenne. Les types dantenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. 13/13