FCC ID: BEJN195WU LED LCD Monitor

Order Number

: GETEC-C1-11-145 Test Report Number

: GETEC-E3-11-065 FCC Part 15 subpart B Page 1 / 1 APPENDIX G

: USERS MANUAL EUT Type: LED LCD Monitor FCC ID.: BEJN195WU E N G L S H I OWNER'S MANUAL NETWORK MONITOR Please read the safety information carefully before using the product. Network Monitor Model N195WU www.lg.com 24 TROUBLESHOOTING 26 PRODUCT SPECIFICATION 27 Preset Mode 27 Power Indicator 28 PROPER POSTURE 28 Proper posture for using the monitor E N E G N L G S H I 2 Table of Contents TABLE OF CONTENTS 3 ASSEMBLING AND PREPARING Unpacking Parts and buttons Lifting and moving the Monitor set Setting Up the Monitor set

- Attaching the Stand Base

- Detaching the stand base

- Adjusting the stand body

- Adjusting the angle

- Mounting on a table

- Using the Kensington locking device

- Detaching the stand body

- Installing the wall mount plate

- Mounting on a wall 3 4 6 6 6 7 7 8 8 9 10 10 11

- D-SUB IN connection - PC 12 USING THE MONITOR SET 12 Uing Primary Station 12 13 Uing Standard Stations 13 13 14 14

- USB cable connection - PC

- USB cable connection to Daisy Chain

- Peripheral device connection

- Self Image Adjustment 15 CUSTOMIZING SETTINGS 15 Accessing The Main Menus 16 MENU Settings 16 17 18 19 20 21 SMART+ Settings 21 22 23 AUTO Settings : D-SUB Input

- Picture

- Color

- Display

- Volume

- Others

- Auto Bright

- Original Ratio ASSEMBLING AND PREPARING 3 ASSEMBLING AND PREPARING Unpacking Please check whether all the components are included in the box before using the product. If there are missing components, contact the retail store where you purchased the product. Note that the product and components may look different from those shown here. E N E G N L G S H I User Manual/

Software Installation CD/

Card Power Cord AC/DC adaptor Stand Base 15-pin D-SUB Signal Cable A-B Type USB Cable CAUTION

y Only use an approved LG power adapter.

y Damage caused by other power adapters is not covered by warranty. NOTE

y Note that the components may look different from those shown here.

y Without prior notice, all information and specifications in this manual are subject to change to improve the performance of the product.

y To purchase optional accessories, visit an electronics store or online shopping site or contact the retail store where you purchased the product. 4 ASSEMBLING AND PREPARING Parts and buttons E N E G N L G S H I Input Connectors

(See p.14) Power Indicator

y LED On :

Power is on

y LED Off:

Power is off

(Power Button) Front Side Buttons Input Connectors (See p.12 to 13) NOTE

y Keep radio away 10 cm from the front side buttons and power button. ASSEMBLING AND PREPARING 5 Description Activates the main menu. OSD Lock/Unlock Functions Locks/unlocks the OSD screen. y To lock the OSD screen, press and hold the MENU button for several seconds. The "OSD LOCKED" message will be displayed and the screen will be locked. y To unlock the OSD screen, press and hold the MENU button again for several seconds. The "OSD UNLOCKED"

message will be displayed and the screen will be unlocked. E N E G N L G S H I Use this button to enter AUTO BRIGHT, ORIGINAL RATIO menus. To adjust the monitor settings, press the AUTO button on the MONITOR SETUP OSD menu (only supported for analog signal(D-SUB)). For optimal screen display, use the following resolution. Optimal Resolution Allows selection of the input signal. y If you connect the monitor to a computer using a D-SUB cable, select either the USB 1366 x 768 y If only one computer is connected to the monitor, the input signal is detected automati-

or D-SUB input signal. cally. The initial input signal is USB. Exits the OSD menu. D-SUB input y Use this button to turn the display on or off. USB input y On : Press the power button to turn on the power. y Monitor Off : Press the power button and automatically turned off after 5 seconds. y USB Off : Press the power button and press it again to turn off the USB power. Power Indicator When the monitor is in operating mode, the power indicator will turn purple (on mode). When the monitor is in power saving mode, the power indica-

tor will blink purple. Button MENU SMART+

AUTO INPUT EXIT

(Power Button) 6 ASSEMBLING AND PREPARING E N E G N L G S H I Lifting and moving the Monitor set When moving or lifting the Monitor set, read the following to prevent the Monitor set from being scratched or damaged and for safe transportation regardless of its type and size. CAUTION

y Avoid touching the screen at all times, as this may result in damage to the screen or some of the pixels used to create images.

y It is recommended to move the Monitor set in the box or packing material that the Monitor set originally came in.

y Before moving or lifting the Monitor set, disconnect the power cord and all cables.

y Hold the top and bottom of the Monitor set frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area. Setting Up the Monitor set Attaching the Stand Base 1 Place the monitor's screen face down. CAUTION

y To protect the screen from scratches, cover the surface with a soft cloth. 2 Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure. Stand Body Stand Base

y When holding the Monitor set, the screen should face away from you to prevent the screen from scratches. 3 Using a coin, turn the screw clockwise to se-

cure the stand base. Stand Body

y When transporting the Monitor set, do not expose the Monitor set to jolts or excessive vibration.

y When transporting the Monitor set, keep the Monitor set upright, never turn the Monitor set on its side, or tilt towards the left or right. Stand Base ASSEMBLING AND PREPARING 7 Detaching the stand base Adjusting the stand body 1 Place the monitor's screen face down. 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. To protect the screen from scratches, cover the surface with a soft cloth. E N E G N L G S H I 2 Using a coin, turn the screw in the stand base counterclockwise. Detach the stand base from the stand body. 2 Press the button as shown and pull the stand body up. Stand Body Stand Base CAUTION

y The components appearing in the illustra-

tions may look different from the actual prod-

uct.

y Do not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury.

y To avoid damaging the screen when lifting or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnec-

essary pressure on the screen. 8 ASSEMBLING AND PREPARING Adjusting the angle Mounting on a table E N E G N L G S H I 1 Place the monitor mounted on the stand base in an upright position. 2 Adjust the angle of the screen. The angle of the screen can be adjusted up to 15 forwards and 5 backwards for a comfortable viewing experi-

ence.

- 5 15 1 Lift the monitor and place it on the table in an upright position. Install at least 10 cm away from the wall to ensure sufficient ventilation. 10 cm 10 cm 10 cm 10 cm Front Side Rear Side WARNING

y To avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor's frame as illustrated below. 2 Connect the adaptor to the monitor, then plug the power cord into the wall outlet.

y Be careful not to touch or press the screen area when adjusting the angle of the monitor. 3 Press the

(Power) button on the front of the monitor to turn on the monitor. CAUTION

y Unplug the power cord prior to moving or installing the monitor. There is risk of electric shock. ASSEMBLING AND PREPARING 9 E N E G N L G S H I Using the Kensington locking device The connector for the Kensington lock is located on the rear of the monitor. For more information on installation and usage, refer to the Kensington lock user manual or visit the website at http://www.kensington.com. Connect the monitor to the table with the Kensing-

ton lock cable. NOTE

y Using the Kensington lock is optional. The accessories can be purchased at your local electronics store. 10 ASSEMBLING AND PREPARING Detaching the stand body E N E G N L G S H I 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. 2 Using a screwdriver, Remove the Cover and detach from the monitor. 3 Using a screwdriver, remove the five screws and detach the stand from the monitor. Installing the wall mount plate This monitor has a VESA compatible mount on the back. Most mounts will require an LG mounting plate. 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. 2 Place the wall mount plate on the monitor and align it with the screw holes on the monitor. 3 Using a screwdriver, tighten the four screws to fix the plate onto the monitor. Wall Mount Plate NOTE

y The wall mount plate is sold separately.

y For more information on the installation, refer to the wall mount plate's installation guide. ASSEMBLING AND PREPARING 11 Mounting on a wall Install the monitor at least 10 cm away from the wall and leave about 10 cm of space at each side of the monitor to ensure sufficient ventilation. De-

tailed installation instructions can be obtained from your local retail store. Please refer to the manual to install and set up a tilting wall mounting bracket. Model VESA (A x B) Stand Screw Required Screw Wall Mount Plate

(Optional) N195WU 75 x 75 M4 4 RW120 E N E G N L G S H I 10 cm

y VESA (A x B) 10 cm 10 cm B A 10 cm If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using the wall mounting interface (optional parts), attach it carefully so it will not drop. 1 Please, Use the screw and wall mount interface 2 3 in accordance with VESA Standards. If you use screw longer than standard, the monitor might be damaged internally. If you use improper screw, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it. 4 VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications. 5 Please use VESA standard as below.

y 784.8 mm (30.9 inch) and under

* Wall Mount Pad Thickness : 2.6 mm

* Screw : 4.0 mm x Pitch 0.7 mm x Length 10 mm

y 787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad and screws. CAUTION

y Unplug the power cord before moving or in-

stalling the monitor to avoid electric shocks. NOTE

y The wall mount kit includes the installation guide and necessary parts.

y The wall mounting bracket is optional. The accessories can be purchased at your local retail store.

y The length of the screw may differ for each wall mounting bracket. Ensure the correct length of the screw is used.

y For more information, please refer to the user manual for the wall mounting bracket. 12 USING THE MONITOR SET USING THE MONITOR SET E N E G N L G S H I Uing Primary Station

y This monitor supports the *Plug and Play feature.

*Plug and Play: A feature that allows you to add a device to your computer, without having to reconfigure anything or install any manual drivers. D-SUB IN connection - PC D-SUB IN transfers analog video signals from the PC to the monitor. Connect the monitor to the PC using the provided 15-pin D-SUB signal cable as illustrated below. CAUTION

y Connect the input signal cable and tighten in the direction of the arrow. To prevent disconnection secure the cable tightly.

y Do not press on the screen for a prolonged time. This may cause image distortion.

y Do not display a still image on the screen for a prolonged time. This may cause image retention. If possible, use the screen saver. Back of the product. NOTE

y To connect the monitor to a computer, use the appropriate signal cable (D-SUB).

y A converter can be used to convert the DVI-I input signal to D-SUB input signal.

y When connecting the power cord to the out-

let, use a grounded (3-hole) multi-socket or a grounded wall outlet.

y The monitor may flicker when turned on in an area of low temperature. This is normal.

y Sometimes red, green or blue spots may ap-

pear on the screen. This is normal. RGB OUT CAUTION

y

USING THE MONITOR SET 13 Uing Standard Stations USB cable connection - PC D-SUB IN transfers analog video signals from the PC to the monitor. Connect the monitor to the PC using the provided 15-pin D-SUB signal cable as illustrated below. USB cable connection to Daisy Chain D-SUB IN transfers analog video signals from the PC to the monitor. Connect the monitor to the PC using the provided 15-pin D-SUB signal cable as illustrated below. E N E G N L G S H I Back of the product. Back of the product. Back of the product. NOTE

y

NOTE

y

y

14 USING THE MONITOR SET Peripheral device connection Connect peripheral devices to the monitor using USB, headphone, speaker, and microphone ports. E N E G N L G S H I Left Bottom NOTE

y Peripheral devices are sold separately.

y The USB ports on the left and bottom of the monitor can be used to connect the key-

board, mouse, and other USB devices.

y Headphones, speakers or microphone may not work normally, depending on the server PC settings.

y Virtual solutions may affect the functions or speed of the specific USB storage device. Self Image Adjustment Press the power button on the front to turn on the monitor. When powered on, the "Self Image Adjustment" function will run automatically (only available for analog [D-SUB input] signals). CAUTION NOTE

y If a PS2 keyboard and mouse are connected to the PC audio device in a multi-computing environment (normal mode), the sound output will be supported through the analog port. If a USB keyboard and mouse are con-

nected, the sound output will be supported through the USB headphones. If using a PC without a PS2 keyboard/mouse input port, please use a USB audio (headphones) for sound output.

y What is "Self Image Adjustment"? This func-

tion runs when the monitor is connected for the first time and performs automatic image adjustment for each signal (only available for analog [D-SUB input] signals) to provide an optimal screen display. CUSTOMIZING SETTINGS 15 CUSTOMIZING SETTINGS Accessing The Main Menus 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press to select the desired menu item. 3 To change the settings of the selected item press the buttons on the front of the monitor. To return to the upper menu or set other menu items, use the up arrow (

) button. 4 Select EXIT to leave the OSD menu. E N E G N L G S H I Front Side Buttons MENU (See p.16) Sets the screen options. AUTOSee p.23) Optimizes the resolution.

/ Disconnects from the server. EXIT(See p.5) Exits the OSD menu. MONITOR SETUP

SMART+ (See p.21) Sets the Auto Bright ,Original Ratio. VOLUME (See p.19) Sets the volume. INPUT (See p.5) Sets the external input. NOTE Different menu items are enabled depending on the type of input signal.

y D-SUB Input: MENU, SMART+, AUTO, INPUT, EXIT

y USB Input: MENU, SMART+, VOLUME, INPUT, EXIT

y The language of the monitor's OSD menu and that of the OSD menu illustrated in the CD-ROM manual may be different. E N E G N L G S H I 16 CUSTOMIZING SETTINGS MENU Settings Picture 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the MENU button to display the options in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. MENU PICTURE BRIGHTNESS CONTRAST SHARPNESS EXIT Each option is explained below. Menu BRIGHTNESS CONTRAST SHARPNESS Analog

(D-SUB) o o o USB o o o Description Sets the brightness of the screen. Sets the contrast of the screen. Sets the sharpness of the screen.

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. NOTE

y If the screen is not displayed properly after adjusting the settings, use the "FACTORY RESET"

option to revert back to the factory default settings. If necessary, enable the "WHITE BALANCE"

option again. This option is enabled only for analog (D-SUB) signals. CUSTOMIZING SETTINGS 17 MENU COLOR COLOR TEMP PRESET RED GREEN BLUE GAMMA PRESET WARM GAMMA 1 EXIT E N E G N L G S H I Color 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the MENU button to display the options in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. Each option is explained below. Menu COLOR TEMP PRESET USER GAMMA Analog

(D-SUB) USB Description o o o o o o o o Allows PRESET or USER to be selected. WARM MEDIUM Sets the screen color to a reddish tone. Sets the screen color between the reddish and bluish tone. Sets the screen color to a bluish tone. COOL You can customize the picture color using Red, Green, and Blue colors. Sets the clarity of the screen. The gamma value can be set to 0, 1 or 2, from darker to brighter screen colors respectively.

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. 18 CUSTOMIZING SETTINGS Display E N E G N L G S H I 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the MENU button to display the options in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. Each option is explained below. MENU DISPLAY HORIZONTAL VERTICAL CLOCK PHASE EXIT Menu HORIZONTAL VERTICAL CLOCK PHASE Analog

(D-SUB) USB Description o o o o x x x x Moves the display area left or right. Moves the display area up or down. If vertical lines are shown on the screen, adjust the frequency to mini-

mize the lines and adjust the screen's horizontal width. Adjusts the focus of the screen's image. Use when frequencies are shown on the screen or when the text ap-

pears overlapped. For optimal results, use this option after adjusting the "CLOCK" option.

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. Volume 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the MENU button to display the options in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. CUSTOMIZING SETTINGS 19

VOLUME E N E G N L G S H I EXIT Each option is explained below. Menu Volume Analog

(D-SUB) x USB o Description To adjust the volume of headphone/Speaker.

(Only for USB input)

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. 20 CUSTOMIZING SETTINGS Others E N E G N L G S H I 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the MENU button to display the options in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. MENU OTHERS LANGUAGE USB POWER INDICATOR BUTTON INDICATOR WHITE BALANCE FACTORY RESET English ON ON ON NO NO EXIT Each option is explained below. Menu LANGUAGE USB POWER INDICATOR BUTTON INDICATOR WHITE BALANCE FACTORY RESET Analog

(D-SUB) USB Description o o o o o o o x o o x o Sets the menu screen to the desired language. Use this function to set the USB input to ON or OFF. Use this function to set the power indicator on the front side of the monitor to ON or OFF. If you set OFF, it will be turned off. If you set ON at any time, the power indicator will automatically be turned on. Use this function to set the control key indicator on the front side of the monitor to ON or OFF. If you set OFF, it will be turned off. If you set ON, it will be turned on. If the video card output is different from the specified level, the color may appear to have altered due to the video signal distortion. The white balance adjusts the output signal level to correspond to that of the standard signal, thus providing optimal display. Run this option when the screen displays an image with both white and black. Resets the screen to the factory default settings. Note that the lan-

guage option will not be reset.

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. CUSTOMIZING SETTINGS 21

AUTO BRIGHT E N E G N L G S H I ON OFF EXIT SMART+ Settings Auto Bright 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the SMART+ button to display the op-

tions in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. Each option is explained below. Menu Analog

(D-SUB) ON OFF o o USB o o Description If select on,it automatically controls the brightness of display to best suit the surrounding working environment,providing the optimal viewing condition and maximized user convenience. If select off,auto brightness is off.

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. 22 CUSTOMIZING SETTINGS Original Ratio E N E G N L G S H I 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the SMART+ button to display the op-

tions in the OSD menu. 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button.

ORIGINAL RATIO WIDE ORIGINAL EXIT Each option is explained below. Menu WIDE ORIGINAL Analog

(D-SUB) o o USB o o Description Switch to full screen mode according to input image signal. Change the input image signal ratio to original. This function works only if input resolution is lower than Monitor set ratio (16:9).

y Analog: D-SUB (analog signal) input. USB: Internal signal through the USB. AUTO Settings : D-SUB Input 1 Press any button on the front of the monitor to dis-

play the MONITOR SETUP OSD menu. 2 Press the AUTO button to automatically adjust the screen. 3 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow (

) button. CUSTOMIZING SETTINGS 23 E N E G N L G S H I PROCESSING AUTO IMAGE ADJUSTMENT FOR OPTIMAL DISPLAY CHANGE RESOLUTION TO 1366 x 768 Pressing the AUTO button allows the monitor to automatically optimize the screen to the current display mode. If you are not satisfied with the optimized screen, you can manually adjust the position of the display area, frequency, phase and sharpness in the OSD menu.

(Only available for D-SUB [analog] signals. Note that the sharpness setting is only available for digital sig-

nals.) NOTE

y What is "Auto Image Adjustment"? The Auto Image Adjustment option allows you to improve the picture quality if the screen is dimmed, if the text appears blurred or spread, if the screen flickers or if the display area is not centered after adjusting the resolution. (Only available for D-SUB [analog]

signals.) 24 Troubleshooting TROUBLESHOOTING E N E G N L G S H I Nothing is displayed on the screen Is the monitor's power cord plugged in?

Is the power indicator on?

Is the power indicator displaying as purple?

Is the power indicator blinking?

y Check if the power cord is correctly plugged in to the outlet. y Check the power indicator. y Adjust the brightness and the contrast. y If the monitor is in power saving mode, move the mouse or press any Is the "OUT OF RANGE" mes-

sage displayed?

key on the keyboard to switch the display on. y Check if the computer is turned on. y This occurs when signals transferred from the PC (video card) are out of the horizontal or vertical frequency range of the monitor. Please see the "Product Specification" section of this manual to set the appropri-

ate frequency. Is the "CHECK SIGNAL CA-

BLE" message is displayed?

y This is displayed when the signal cable between the PC and the moni-

tor is missing or disconnected. Check the cable and reconnect. The "OSD LOCKED" message is displayed. Is the "OSD LOCKED" mes-

sage displayed when the MENU button is pressed?

y The OSD lock feature is enabled to prevent undesired modification of the OSD settings. Press and hold the MENU button for a couple of seconds to unlock the OSD. (The "OSD UNLOCKED" message will be displayed.) The screen retains an image. Does image sticking occur even when the monitor is turned off?

y Displaying a still image for a prolonged time may cause damage to the screen, resulting in the retention of the image. y Use a screen saver to protect the screen when using the monitor for a prolonged period of time. NOTE

y Vertical Frequency: In order to display an image, the screen must be refreshed dozens of times per second like a fluorescent lamp. The number of times the screen is refreshed per second is called vertical frequency or refresh rate and is represented by Hz.

y Horizontal Frequency: The time it takes to display one horizontal line is called the horizontal cycle. The number of horizontal lines displayed in one second can be calculated by dividing one by the horizontal cycle. This is called horizontal frequency and is represented by kHz. Troubleshooting 25 Pressing the AUTO button will automatically optimize the screen to the current display mode. If you are not satisfied with the optimized screen, you can manually adjust the POSITION option in the OSD menu. Pressing the AUTO button will automatically optimize the screen to the current display mode. If you are not satisfied with the optimized screen, you can manually adjust the FREQUENCY option in the OSD menu. Pressing the AUTO button will automatically optimize the screen to the current display mode. If you are not satisfied with the optimized screen, you can manually adjust the PHASE option in the OSD menu. E N E G N L G S H I The image is displayed abnormally. Does the display area appear uncentered?

Does the screen exhibit vertical lines?

Does the screen display hori-

zontal frequencies, or does the text appear blurred?

NOTE

y Check if the video card's resolution or frequency is within the range allowed by the monitor and set to the recommended (optimal) resolution in Control Panel > Display > Settings.

y Failing to set the video card to the recommended (optimal) resolution may result in blurred text, a dimmed screen, a truncated display area or misalignment of the display.

y The configuration procedure may differ depending on your computer and/or operating system. Also, some video cards may not support certain resolutions. If this is the case, contact the computer or video card manufacturer for assistance.

y The AUTO option is only available for D-SUB (analog) signals. The display color is abnormal. Does the display color appear discolored (16 color)?

Does the display color appear unstable or in monochrome?

Are there spots on the screen?

y Set the color to 24 bit (true color) or higher. In Windows, go to Control Panel > Display > Settings > Color Quality. y Check if the signal cable is connected properly. Re-connect the cable or re-insert the PC's video card. y When using the monitor, pixilated spots (red, green, blue, white or black) may appear on the screen. This is normal for the LCD screen. It is not an error nor is it related to the monitor's performance. 26 6SHFLFDWLRQV PRODUCT SPECIFICATION E N E G N L G S H I LCD Screen Resolution Video Signal Input Connector Power Type 470.1 mm (18.51 inch) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Screen Diagonal length of the screen: 470.1 mm Pixel Pitch 0.30 mm x 0.30 mm Maximum Resolution 1366 x 768 @ 60 Hz Recommended Resolution 1366 x 768 @ 60 Hz Horizontal Frequency Vertical Frequency Synchronization 15-pin D-SUB (Analog), USB 19 V Power Consumption 30 kHz to 66 kHz 57 Hz to 63 Hz Separate Sync/PCoIP 2.3 A On Mode: 22 W (Typical) 3RZHU6DYLQJ0RGH::

2II0RGH:

AC/DC Adapter Manufacturer : LITE-ON, Model PA-1650-68 Dimension/

Weight Weight (Without Packaging) Stand Angle Adjustment Environment Condition Input: AC 100~240 V Output: DC 19 V Monitor Size (Width x Height x Depth) 457.9 mm x 197.9 mm x 369.5 mm 2.6 kg Forwards/Backwards: -5 to 15 (Monitor) Operating Condition Storing Condition Temperature: 10C to 35C;

Humidity: 10% to 80%

Temperature: -20C to 60C;

Humidity: 5% to 90%

The specifications are subject to change without notice. 3URGXFW6SHFLFDWLRQ 27 Preset Mode Preset Mode 720 x 400 640 x 480 800 x 600 1024 x 768 1360 x 768 1366 x 768 Horizontal Frequency (kHz) 31.468 31.469 37.879 48.363 47.712 47.712 Vertical Frequency (Hz) 70 60 60 60 60 60 Polarity (H/V) Remark

E N E G N L G S H I Power Indicator Mode On Mode Power Saving Off Mode LED Color Purple Flashing Purple Off 28 Proper Posture E N E G N L G S H I PROPER POSTURE Proper posture for using the monitor Adjust the angle so that the screen is slightly lower than your eyes.

y Using the monitor for a prolonged period of time can cause eye fatigue. Take a 10-minute break every hour.

y The stand is designed to best support the monitor when the optimal conditions are selected. Adjust the angle of the monitor from -5 to 15 to obtain the best view of the screen. Adjust the angle from -5 to 15 so that there is no re-

flection or glare from the screen. You should be looking slightly down at the screen. Place your hands gen-

tly on the keyboard, keeping your arms bent at the elbows and extended horizon-

tally in front of you. Make sure to read the Safety Precautions before using the product. Keep the Owner's Manual(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service. MODEL SERIAL Regulatory Information cont. FCC Compliance Statement This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) Products with the CE Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive

(73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :

EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 EN 60950-1

; Radio Frequency Interference

; Electromagnetic Immunity

; Power Line Harmonics

; Voltage Fluctuations

; Product Safety NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. TCO'99 (TCO'99 applied model only) Congratulations!

You have just purchased a TCO99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. 01 Regulatory Information cont. Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy. What does labelling involve?

The product meets the requirements for the TCO99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen

(The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues:

ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered. Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Developments website http://www.tcodevelopment.com or may be ordered from:

TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCO99 approved and labelled products may also be obtained at http://www.tcodevelopment.com Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30%

by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fish-

eating birds and mammals, due to the bio-accumulative*

processes when not disposed of in accordance with strict standards for disposal. TCO99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives. Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCO99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium. Mercury**

Mercury is sometimes found in batteries, relays and switches. TCO99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one 02 Regulatory Information cont. exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. TCO99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________

* Bio-accumulative is defined as substances which accumulate in living organisms.

**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative. TCO03 (TCO03 applied model only) Congratulations!

The display you have just purchased carries the TCO03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO03 Display requirements:

Ergonomics Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields 03 Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www.tcodevelopment.com English Information for Environmental Preservation LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors. Information for recycling This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use. LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in Regulatory Information cont. operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our green policies. http://www.lge.com/about/environment/html/Recycling.jsp Deutsch Informationen zur Erhaltung der Umwelt Im Jahr 1994 verkndete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklrung fr eine sauberere Umwelt). Seitdem dient dieses Ideal als fhrendes Prinzip des Unternehmens. Diese Erklrung war die Basis fr die Durchfhrung von umweltfreundlichen Aktivitten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die berlegungen mit einbezogen wurden. Wir frdern Aktivitten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schdlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden. Informationen zum Thema Recycling Dieser Monitor enthlt Teile, die umweltschdlich sein knnen. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er auer Dienst gestellt wurde. Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere Rcknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schdliche Substanzen und Schwermetalle werden durch umweltvertrgliche Verfahren behandelt. Falls Sie mehr ber unser Recyclingprogramm erfahren mchten, wenden Sie sich bitte an Ihren lokalen LG-

Hndler oder einen Unternehmensvertreter von LG. 04 Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einflieen lassen. Zustzliche Informationen ber unsere grne Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/about/environment/html/Recycling.jsp Franais Information sur la protection delenvironnement LGE. a publi sa 'Dclaration en faveur dun environnement plus propre' en 1994 et celle-ci est reste, depuis lors, un principe directeur de notre entreprise. Cette dclaration a servi de base notre rflexion et nous a permis de prendre en compte la fois les aspects conomiques et sociaux de nos activits, tout en respectant lenvironnement. Nous encourageons les activits en faveur de la prservation de lenvironnement et cest dans cet esprit que nous dveloppons nos produits : nous rduisons au minimum les matires dangereuses qui entrent dans leur composition et lon ne trouve pas de cadmium, par exemple, dans nos moniteurs. Information sur le recyclage Ce moniteur peut contenir des composants qui prsentent un risque pour lenvironnement. Il est donc important que celui-ci soit recycl aprs usage. LGE. traite les moniteurs en fin de cycle conformment une mthode de recyclage respectueuse de lenvironnement. Nous reprenons nos produits et les recyclons dans plusieurs sites rpartis dans le monde entier. De nombreux composants sont rutiliss et recycls, et les matires dangereuses, ainsi que les mtaux lourds, sont traits selon un procd cologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un lun de nos reprsentants. Nous voulons agir pour un monde plus propre et croyons au rle de notre entreprise dans lamlioration de lenvironnement. Pour plus de renseignements sur notre politique verte, rendez visite notre site :

http://www.lge.com/about/environment/html/Recycling.jsp Regulatory Information cont. Italiano Informazioni per la tutela dellambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente pi pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attivit a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attivit a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dellambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non presente il cadmio. Informazioni per il riciclaggio Il monitor pu presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. importante che il monitor sia riciclato al termine del suo utilizzo. La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dellambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG. Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo pi pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica verde. http://www.lge.com/about/environment/html/Recycling.jsp Espanl Informacin para la conservacin medioambiental LGE. present la 'Declaracin para un entorno ms limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaracin es la base que nos ha permitido llevar a cabo tareas que 05 respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, econmicos y medioambientales. Promocionamos actividades orientadas a la conservacin del medio ambiente y desarrollamos nuestros productos especficamente para que se ajusten a la filosofa que protege el entorno. Reducimos al mximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores. Informacin para el reciclaje Este monitor puede contener piezas que entraen riesgos medioambientales. Es importante reciclar este monitor despus de su utilizacin. LGE. trata todos los monitores usados siguiendo un mtodo de reciclaje que no daa al entorno. Contamos con diversos sistemas de recuperacin y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dainas y los metales pesados se tratan siguiendo un mtodo que no perjudique al medio ambiente. Si desea obtener ms informacin acerca del programa de reciclaje, pngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca. Basamos nuestra visin y nuestras polticas en un mundo ms limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolucin como empresa. Visite nuestra pgina Web para obtener ms informacin sobre nuestras polticas ecolgicas. http://www.lge.com/about/environment/html/Recycling.jsp Portugus Informaes relacionadas preservao ambiental A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declarao da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde ento como um princpio administrativo de orientao. A Declarao a base que nos tem permitido realizar atividades favorveis ao ambiente com considerao atenta aos aspectos econmicos, ambientais e sociais. Promovemos atividades de preservao ambiental e desenvolvemos nossos produtos para englobar Regulatory Information cont. especificamente o conceito de favorvel ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, no h cdmio em nossos monitores. Informaes relacionadas reciclagem Este monitor pode conter peas que podem representar riscos ao ambiente. importante que ele seja reciclado aps o uso. A LGE. cuida de todos os monitores descartados atravs de um mtodo de reciclagem agradvel ao ambiente. H vrios sistemas de devoluo e reciclagem atualmente em operao no mundo. Muitas peas sero reutilizadas e recicladas e as substncias nocivas e os metais pesados passaro por tratamento atravs de um mtodo favorvel ao ambiente. Para obter mais informaes sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa viso e nossas polticas relacionadas a um mundo mais limpo selecionando a questo do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informaes sobre nossas polticas de meio ambiente. http://www.lge.com/about/environment/html/Recycling.jsp Nederlands Informatie met betrekking tot het behoud van het milieu LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden. Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled. LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LG-

vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/about/environment/html/Recycling.jsp Russian 1994 LGE

' LG ',

. 06 Regulatory Information cont. K LGE

. LG.

http://www.lge.com/about/environment/html/Recycling.jsp EPA (EPA applied model only) ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. NOM MARK (Mexico only) 07 Regulatory Information cont. WEEE (for Europe ) English Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. French limination de votre ancien appareil 1.Ce symbole, reprsentant une poubelle sur roulettes barre d'une croix, signifie que le produit est couvert par la directive europenne 2002/96/EC. 2.Les lments lectriques et lectroniques doivent tre jets sparment, dans les vide-

ordures prvus cet effet par votre municipalit. 3.Une limination conforme aux instructions aidera rduire les consquences ngatives et risques ventuels pour l'environnement et la sant humaine. 4.Pour plus d'information concernant l'limination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures mnagres ou encore la magasin o vous avez achet ce produit. Italian Smaltimento delle apparecchiature obsolete 1.Quando su un prodotto riportato il simbolo di 08 un bidone della spazzatura barrato da una croce significa che il prodotto coperto dalla direttiva europea 2002/96/EC. 2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorit locali. 3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente. 4.Per informazioni pi dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui stato acquistato il prodotto. Swedish Kassering av din gamla apparat 1.Nr den hr symbolen med en verkryssad soptunna p hjul sitter p en produkt innebr det att den regleras av European Directive 2002/96/EC. 2.Alla elektriska och elektroniska produkter br kasseras via andra vgar n de som finns fr hushllsavfall, helst via fr ndamlet avsedda uppsamlingsanlggningar som myndigheterna utser. 3.Om du kasserar din gamla apparat p rtt stt s bidrar du till att frhindra negativa konsekvenser fr miljn och mnniskors hlsa. 4.Mer detaljerad information om kassering av din gamla apparat kan fr av kommunen, renhllningsverket eller den butik dr du kpte produkten. Dutch Uw oude toestel wegdoen 1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC. 2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen. 3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen. Regulatory Information cont. 4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht. Finnish Vanhojen laitteiden hvittminen 1.Tm merkki tuotteessa tarkoittaa, ett tuote kuuluu shk- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan. eller de lokale myndigheder. 3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger p miljet og menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse af dit gamle apparat kan fs ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du kbte produktet. Greek 2.Kaikki elektroniset laitteet ovat ongelmajtett, 1. joten ne on toimitettava paikalliseen keryspisteeseen. 3.Vanhan laitteen asianmukainen hvittminen ehkisee mahdollisia ympristn ja terveyteen kohdistuvia haittavaikutuksia. 4.Listietoa vanhan laitteen hvittmisest saat ottamalla yhteyden paikallisiin viranomaisiin, kierrtyskeskukseen tai myymln, josta ostit laitteen. German Entsorgung von Altgerten 1.Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europischen Richtlinie 2002/96/EC. 2.Alle Elektro- und Elektronik-Altgerte mssen getrennt vom Hausmll ber dafr staatlich vorgesehenen Stellen entsorgt werden. 3.Mit der ordnungsgemen Entsorgung des alten Gerts vermeiden Sie Umweltschden und eine Gefhrdung der persnlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des alten Gerts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschft, wo Sie das Produkt erworben haben. Danish Sdan smider du dit gamle apparat ud 1.Nr der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC. 2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjlp af specielle indsamlingsfaciliteter, der er organiseret af staten

, E O 2002/96/EOK. 2.H

. 3.H

. 4.

. Spanish Cmo deshacerse de aparatos elctricos y electrnicos viejos 1.Si en un producto aparece el smbolo de un contenedor de basura tachado, significa que ste se acoge a la Directiva 2002/96/CE. 2.Todos los aparatos elctricos o electrnicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a travs de puntos de recogida designados por el gobierno o las autoridades locales. 3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pblica. 4.Para obtener ms informacin sobre cmo deshacerse de sus aparatos elctricos y electrnicos viejos, pngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquiri el producto. 09 Regulatory Information cont. Portuguese Hungarian Polish 10 Slovak Czech Croatian Regulatory Information cont. Estonian Latvian Lithuanian 11