FCC ID: BEJ50PY2DRUA PDP Display

PLASMA TV OWNERS MANUAL MODELS: TU-50PY22/TU-50PY2DR-UA TU-60PY22/TU-60PY2DR-UA R TruSurround XT TM Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service. Model Number :

Serial Number :

LG Electronics U.S.A., Inc. Warning/Caution WWarning/Caution arning/Caution

/CAUTION WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-

cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli-

ance. WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compli-

ance could void the users authority to operate the equipment. CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod-

ification could void the users authority to operate this product. COMPLIANCE:

The responsible party for this products compliance is:

LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-201-816-2000 http://www.lgusa.com WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 2 Plasma TV TV Guide On Screen Notices for U.S.A. TV Guide On Screen Notices for U.S.A. In the United States, the TV Guide On Screen system and other related marks are registered marks of Gemstar-TV Guide On Screen system International, Inc. and/or one of its affiliates. In Canada,TV Guide On Screen system is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide On Screen system International, Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide On Screen system International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. Use of the CableCARDTM TradeMark. CableCARDTM is a trademark of Cable Television Laboratories, Inc. Digital Cable Compatibility Digital Cable Compatibility This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable operator enhanced program (For example, electronic program guide provided by the cable operator), and data enhanced television service may require the use of a set top box. For more information contact your local cable operator. Owners Manual 3 Warning/Caution Safety Instructions Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa-

ratus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled Important Safety Instructions. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturers option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-

fiers)that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING 4 Plasma TV Safety Instructions 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. 15. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 16. Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture. 17. Wet Location Marking :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Owners Manual 5 Contents Contents Contents Warning/Caution . 2 Digital Cable Compatibility . 3 Safety Instructions . 4~5 Introduction Controls . 8 Connection Options . 9 Remote Control Key Functions . 10~11 Installation Install the RING SPACER with the bolts on the set as . shown . 12 Installation Instructions . 13~15 Remove or Attache the Plate Cover . 13 Joining the TV assembly to the wall to protect the set tum-

bling . 14 Swivel function . 15 Arrangement wires . 15 External Equipment Connections . 16~21 Antenna or Cable Connection . 16~17 VCR Setup . 17 External A/V Source Setup . 18 DVD Setup . 18 CableCARDTM Setup . 19 HDSTB Setup . 19 PC Setup . 21 Monitor Out Setup . 21 Digital Audio Output . 21 HDMI/DVI (VIDEO) . 22~24 TV Guide On Screen Setup . 25~33 Operation Screen Setup for PC mode Adjustments for screen Position, Size, and Phase . 34 Turning the TV On . 35 Home Menu Recorded TV . 36~37 Using the Memory Card . 38~40 Photo List . 41~42 Music list . 43~45 TV Guide On Screen System . 46~66 IEEE 1394 . 67~75 Setup Menu Options On-screen Menus Language Selection . 76 EZ Scan (Channel Search) . 77 Manual Scan . 77 Channel Edit . 78 DTV Signal Strength . 78 Channel Label Setup . 79 Main Picture Source Selection . 79 Aux.Label . 79 Video Menu Options EZ Picture . 80 Manual Picture Control (Off Option) . 80 Color Temperature Control . 80 Video Reset . 80 Audio Menu Options Audio Language . 81 EZ SoundRite / EZ Sound . 81 Manual Sound Control (custom Option) . 82 Front Surround . 82 TV Speakers On/Off Setup . 83 Stereo/SAP Broadcasts Setup . 83 BBE . 83 Time Menu Options Auto Clock Setup . 84 Manual Clock Setup . 84 On/Off Timer Setup . 84 Sleep Timer / Auto Off . 85 Option Menu Features Advanced . 86 Timeshift Mode . 86~87 Recording . 88~90 Cinema 3:2 Mode Setup . 91 Low Power . 91 LG Logo . 92 Aspect Ratio Control . 93 Caption . 94 Caption / Text . 94 Caption Option

. 95 ISM Method . 96 Front LED (Light Emitting Diode) Display . 96 Auto Demo . 97 Lock Menu Options CableCARDTM Function Parental Lock Setup . 99 Cable menu options . 100 Scrambled channel . 100 Cable Channel List . 101 Emergency Alert Message . 101 Remote Control PIP (Picture-in-Picture)/Twin Picture . .102 Watching PIP/POP/Twin Picture . .102 Selecting an Input Signal Source for PIP/Twin Picture .102 Swapping PIP/Twin Picture . 102 TV Program Selection for PIP . 102 Moving the PIP sub picture . 103 Adjusting Main and Sub Picture Sizes for Twin Picture .103 POP (Picture-out-of-Picture: Channel Scan) . 103 Information . 104 EZ Mute . 105 External Control Device Setup . 106~111 IR Codes . 112~113 Programming the Remote . 114 Programming Codes . 115~116 Troubleshooting Checklist . 117 Maintenance . 118 Product Specifications . 119 Warranty . 120~121 6 Plasma TV After reading this manual, keep it handy for future reference. Introduction Introduction Introduction What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps. How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phos-

phors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors. You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of these mean that you get perfect images that are easily viewable in a display that is less than 5 inches thick. 160 - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen. Wide Screen The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit. The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen The PDP (Plasma Display Panel), which is the display device of this product, is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defec-

tive. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology mini-

mizes these cell defects during the manufacture and operation of this product. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operat-

ing and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not suffi-

cient cause for the PDP to be exchanged or returned. Owners Manual 7 Introduction Controls Controls

- This is a simplified representation of front panel. Here shown may be somewhat different from your TV. Front Panel Controls Front Panel Controls CHANNEL Buttons VOLUME Buttons MENU Button TV/VIDEO Button TV GUIDE Button POWER Button INDEX Switches LED Display on or off. Remote Control Sensor Power Indicator Blinks orange in standby mode, blinks green when the TV is turned on.

(After orange stop the blinking,direct-

ly turn on the TV, but in case of green, screen is displayed at 3~4 minutes later. If power isnt turn on in red, contact your service center.) 8 Plasma TV Connection Options Connection Options Introduction Back Connection Panel Back Connection Panel FRONT A/V INPUT O E D V S

I O E D V I O N O M

L I O D U A R R S-VIDEO Input A connection available to provide bet-

ter picture quality than the video input. VIDEO Input Connects the video signal from a video device. AUDIO Input Use to connect to hear stereo sound from an external device. DVD/DTV Input

(Component 1-

2) Connect a DVHS, a MicroMV Camcorder, or a Set-Top Box to one of IEEE1394 con-

nectors. Remote Control Port Connect your wired remote control here. S-Video Input Connect S-

Video out from an S-VIDEO device. Antenna Input Connect antenna signals to the TV, either directly or through your cable box. RS-232C INPUT

(CONTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT S V I D E O R C E M O T E O N T R O L CABLE ANTENNA AC INPUT I 1 E 3 E 9 E 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT RS-232C INPUT

(CONTROL/SER-

VICE) PORT Connect to the RS-

232C port on a PC. IEEE1394 Connect DVHS or MicroMV to IEEE1394 Connector. RGB/AUDIO INPUT Connect the moni-

tor output connec-

tor from a PC to the appropriate input port. RS-232C INPUT

(CONTROL/SERVICE) Cable G-LINK Connect an IR controller to this jack. CableCARD Used for CableCARD received Cable Service Provider. IEEE-1394 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT AC INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO REMOTE CONTROL CABLE ANTENNA HDMI1/DVI(VIDE O), HDMI 2 Connect a HDMI signal to HDMI1/DVI or HDMI2. Or DVI(VIDEO) sig-

nal to HDMI1/DVI port with DVI to HDMI cable. Digital Audio (DVI:

Digital Visual Interface/Compon ent2) Input/

Digital Audio Output Connect digital audio from various types of equipment. Note: In standby mode, these ports will not work. Audio/Video Input Connect audio/video output from an exter-

nal device to these jacks. Monitor Output Connect a second TV or Monitor. CABLE Input Connect cable signals to the TV, either directly or through your cable box. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.

- This manual explains the features available on the TU-50PY22 series TVs. Owners Manual 9 Introduction Remote Control Key Functions Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the TV. POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT TV/VIDEO X STUDIO Bring up the HOME menu to the screen. MODE D A Y

DAY +

THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your pref-

erence. REC LIST Appear the thumbnail recorded list. VOLUME UP/DOWN Increases/decreases the sound level. NUMBER buttons RATIO Changes the aspect ratio. FLASHBK VCR/DVD BUTTONS Control some video cassette recorders or DVD players.

("RECORD" button is not available for DVD players.)

< Only TV mode >

In Photo mode of Xstudio, the view state changes to the slide show state with PLAY button and the slide show state changes to the view state with PAUSE button. In Music mode of Xstudio, controls the music with PAUSE, STOP, PLAY, (Left/Right) SKIP buttons. Note that FF and REW do not work in the mode. Control the DVHS or Camcorder of IEEE 1394 mode. DAY+/DAY-

Moves forward or backward in 24 hour increments in the Listings Grid. CHANNEL UP/DOWN Selects available channels found with EZ scan. PAGE UP/PAGE DOWN Moves from one full set of screen information to the next one. APM CC AUTO DEMO M/C EJECT EZ SOUND Selects the sound appropriate for the program's character. ATM Concurrently, compare with the Daylight, Normal, Night Time.and Custom on the screen. SAP Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode. CC Select a closed caption:

Off, CC1~4, Text1~4. M/C EJECT When removing the Memory Card, this button is used. LIGHT Illuminates the remote control buttons. 10 Plasma TV TV INPUT When you watch the TV, Antenna and Cable is toggled. In Video, Front Video, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2 and IEEE1394 input sources, screen return to the last TV chan-

nel. MODE Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE or STB. Select other operating modes, for the remote to operate external devices. MENU Brings up the main menu to the screen. Enters or exits a Panel Menu in the TV Guide On Screen system. EXIT Clears all on-screen displays and returns to TV viewing from any menu. MUTE Switches the sound on or off.(Refer to p.79) TIMER Lets you select the amount of time before your TV turns itself off automatically. ADJUST Adjusts screen position, size, and phase in PC mode. APM CC AUTO DEMO M/C EJECT EZ PIC Adjusts the factory preset picture depending on the viewing environment. AUTO DEMO Displays the slide show to explain the main features of this TV. TV INPUT TV/VIDEO MODE D A Y

DAY +

Introduction TV/VIDEO When you watch the TV, screen return to the last external (Video1-2, Component 1-

2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2) input. Selects: Video 1-2, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI and HDMI2 input sources.

(Only when the jack connects , Video 1-2, Component 1-2 input sources are linked automatically) TV GUIDE Brings up the TV Guide On Screen sys-

tem to the screen. INFO When you watch the TV, information dis-

plays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.(Refer to p.78) Mark Selects the wanted functions. FAV Scroll the Favorite channels. FLASHBK FLASHBK Tunes to the last channel viewed. PIP Switches between PIP, POP (Picture-out-

of-Picture) and Twin picture modes. Switches the video window locking or unlocking in the Listings Grid. PIPCH-/PIPCH+

Changes to next higher/lower PIP chan-

nel. PIP INPUT Selects the input source for the sub pic-

ture. SWAP Exchanges the main/sub images in PIP/Twin picture mode. Installing Batteries Installing Batteries Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). Install two 1.5V AA batteries. Dont mix old or used batteries with new ones. Replace cover. Owners Manual 11 Installation Installation Installation Accessories Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. T V IN P U T M E O D 1.5V 1 . 5 V Y +

A D DAY -

F L A S H B K A P M AUTO DE M O C C Owners Manual Batteries Remote Control Power Cord 2-TV brackets 2-Wall brackets 4-TV bracket bolts(50) 2-TV bracket bolts(60) D-sub 15 pin Cable 75 Round Cable 6-RING SPACER

(Only TU-60PY22 series ) 6-Wall mounting bracket bolts

(Only TU-60PY22 series ) G-LINK Cable Installation Instructions Installation Instructions Joining the TV assembly to the wall to protect the set tumbling TV assembly to the wall to protect the set tumbling Joining the

- Secure the TV assembly by joining it to a wall by using the TV/Wall brackets. After the set must be mounted on the desk top, install the TV brackets on the TV as shown. Install the TV brackets on the TV as shown. Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the product), as shown. Match the height of the TV brackets and the wall brack ets. Check to be sure the brackets are tightened securely. Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown. 12 Plasma TV GROUNDING Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Installation Power Supply Short-circuit Breaker The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally. WWall Mount: Horizontal installation all Mount: Horizontal installation Desktop Pedestal Installation Desktop Pedestal Installation For proper ventilation, allow a clearance of 4 on each side and 2 from the wall. Detailed installation instruc-

tions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide. For proper ventilation, allow a clearance of 4 on each side and the top, 2.36 on the bottom, and 2 from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Setup Guide available from your dealer. 4 inches 2 inches 4 inches 2 inches 4 inches 4 inches 4 inches 4 inches 4 inches 2.36 inches Install the RING SPACER with the bolts on the set as shown. Install the RING SP ACER with the bolts on the set as shown.(Only TU-60PY22 series ) 2. When you connect the wall mounting bracket to the set, connect to it by using the bolts,

(supplied with the product), as shown. 1. Put the RING SPACER in the holes of the bolts before connecting to the wall mounting bracket. Owners Manual 13 Installation Remove or Attache the Plate Cover Attache the Plate Cover Remove or

- When moving or connecting the power cord, be used the these methods.

- And after removing the plate cover, you must install the wall brackets on the wall. RS-232C INPUT

(CONTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O R E M O T E C O N T R O L DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT CABLE ANTENNA AC INPUT I E E E 1 3 9 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT 1. With hands, push the lower left/right of plate cover and then pull out to the front. 2. Connect the power cord on the TVs back. 3. In attaching the plate cover, firstly you set projection of the GUIDE to BUSHING RUBBER of the upper left/right. Push and put the plate cover with hands. 14 Plasma TV Installation Swivel function Swivel function After installing the TV, you can adjust the the TV set manually to the left or right direction by 20 degrees to suit your viewing position. Note: Before adjusting the angle, you must loosen (to the left) the shaft bolt on the middle of stands back. And when stand be level with TV, you must close (to the right) the shaft bolt to set the hole.(As shown below) 50 60 50 20 Arrangement wires Arrangement wires Run the accessory device wires and power cord inside the JACK MANAGEMENT pole as shown. RS-232C INPUT

(CONTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O R E M O T E C O N T R O L DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT CABLE ANTENNA AC INPUT I E E E 1 3 9 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT Owners Manual 15 Installation External Equipment Connections External Equipment Connections Antenna or Cable Connection Antenna or Cable Connection 1. Analog and Digital TV signals provided on antenna

- Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments

(Connect to wall antenna socket) Wall Antenna Socket AC INPUT Bronze Wire CABLE ANTENNA RF Coaxial Wire (75 ohm) VHF Antenna UHF Antenna Turn clockwise to tighten. Outdoor Antenna Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna) Bronze Wire Be careful not to bend the bronze wire when connecting the antenna. 2. Analog and Digital TV signals provided on cable Cable TV Wall Jack Turn clockwise to tighten. RF Coaxial Wire (75 ohm) AC INPUT Bronze Wire CABLE ANTENNA 16 Plasma TV 3. Analog and Digital TV signals provided on cable and antenna Antenna Bronze Wire RF Coaxial Wire (75 ohm) Installation Cable TV Wall Jack Turn clockwise to tighten. AC INPUT RF Coaxial Wire (75 ohm) CABLE ANTENNA ANTENNA Bronze Wire In a poor signal area to improve picture quality, purchase and install a signal amplifier. If the antenna needs to be split for two TVs, install a 2-

Way Signal Splitter in the connections. If the antenna is not installed properly, contact your deal-

er for assistance. Signal Amplifier Note: The TV will let you know when the analog, cable, and digital channel scans are complete. VCR Setup VCR Setup

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) 3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT , select Video input source) Do not connect to both Video and S-Video at the same time. S-232C INPUT NTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O R E M O T E C O N T R O L DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT CABLE ANTENNA AC INPUT 1 2 ANT OUT ANT IN S-VIDEO OUT OUTPUT SWITCH 3 4 IN

(R) AUDIO (L) VIDEO VCR Rear Owners Manual 17 Installation External A/V Source Setup A/V Source Setup External How to connect Connect the audio and video cables from the external equip-

ment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Select the input source with using the TV/VIDEO button on HDMI 2 DMI /DVI RS-232C INPUT

(CONTROL/SERVICE) OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT S V I D E O R E M O T E C O N T R O L AC INPUT CABLE ANTENNA COMPONENT INPUT 1

(MONO) A/V INPUT the remote control. Note that this TV finds the connected input sources automatically for Video 1-2 and Component 1-

2. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected. 2. Operate the corresponding external equipment. Refer to external equipment operating the tv guide on screen system. DVD Setup DVD Setup RS-232C INPUT

(CONTROL/SERVICE) Camcorder R AUDIO L VIDEO Video Game Set IEEE-1394 HDMI 2 HDMI1 /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT or VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT AC INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT S-VIDEO REMOTE CONTROL CABLE ANTENNA DVD DIGITAL AUDIO OPTICAL

(R) AUDIO (L) B R S-VIDEO

(R) AUDIO (L) or How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. Note: If your DVD player does not have component video output, use S-Video. How to use 1. Turn on the DVD player, insert a DVD. 2. Use the TV/VIDEO button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video or Front Video external input source.) 3. Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the compo-

nent input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PR Pb B-Y Cb PB Pr R-Y Cr PR 18 Plasma TV Notes:

Digital Audio will not work for Component 1 input source. Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. Installation CableCARDTMTM Setup Setup CableCARD How to use Insert the CableCARDTMTM received from the cable service provider to the CableCARDTMTM slot of TV back panel. If the pairing information about this TV and the CableCARD is automati-

cally displayed on the screen, contact with the cable service provider by phone. Note :

CableCARDTMTM have the types of Motorola, Scientific Atlanta, SCM etc.. These 3 types of CableCARDTMTM can be used for this PLASMA TV. Cable IEEE-1394 HDMI 2 HDMI1 /DVI RS-232C INPUT

(CONTROL/SERVICE) OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB I Caution: When removing the CableCARDTMTM, do not fall it as this may cause impact to the CableCARDTMTM. HDSTB Setup HDSTB Setup

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI1 /DVI OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1

(MONO) A/V INPUT S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA or or RGB-DTV OUTPUT

(R) AUDIO (L)

(R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI-DTV OUTPUT HDMI-DTV OUTPUT DIGITAL AUDIO OPTICAL

(R) AUDIO (L) B R Digital Set-top Box How to connect Use the TVs COMPONENT (Y, PB, PR) INPUT, RGB, HDMI1/DVI or HDMI2 jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) 2. Use TV/VIDEO on the remote control to select Component 1, Component 2, RGB-DTV, HDMI1/DVI or HDMI2 source. Signal 480i 480p 720p 1080i Component 1/2 RGB-DTV,HDMI1/DVI,HDMI2 Yes Yes Yes Yes No Yes Yes Yes Owners Manual 19 Installation PC Setup PC Setup

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly.

<When the PC supports DVI>

How to connect 1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product). If you do not need to connect audio, HDMI2 port is also available for the DVI video connection. 2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGI-

TAL AUDIO(OPTICAL) port for DVI INPUT. 3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.62) TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

<When the PC supports RGB>

How to connect 1. Connect the PC to RGB INPUT port of this TV with a RGB cable. 2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz. 2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.57) Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. Monitor Display Specifications (RGB-PC ) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 720x400 640x480 31.468 37.861 31.469 37.927 31.469 37.861 37.500 43.269 70.09 85.08 70.08 85.03 59.94 72.80 75.00 85.00 800x600 1024x768 35.156 37.879 48.077 46.875 53.674 48.363 56.476 60.023 56.25 60.31 72.18 75.00 85.06 60.00 70.06 75.02 20 Plasma TV Monitor Display Specifications (HDMI/DVI Mode) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Installation 640x480 800x600 31.469 37.861 37.500 35.156 37.879 48.077 46.875 59.94 72.80 75.00 56.25 60.31 72.18 75.00 Monitor Out Setup Monitor Out Setup RGB INPUT AUDIO INPUT DVD

/DTV INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1

(MONO) A/V INPUT S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA 1024x768 48.363 56.476 60.023 60.00 70.06 75.02 The TV has a special signal output capability which allows you to hook up a second TV or monitor. Connect the second TV or monitor to the TVs MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that devices input settings. Note Component, RGB-PC/RGB-DTV, HDMI1/DVI and HDMI2 , DTV input sources cannot be used for Monitor out. S-VIDEO IN VIDEO

(L) AUDIO (R) Digital Audio Output Audio Output Digital Send the TVs audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port. How to connect 1. Connect one end of an optical cable to the TV Digital Audio

(Optical) Output port. 2. Connect the other end of the optical cable to the digital audio (opti-

cal) input on the audio equipment. 3. Set the TV Speaker option - Off in the AUDIO menu. Refer to page 64. See the external audio equipment instruction manual for operation. Caution: Do not look into the optical output port. Looking at the laser beam may damage your vision. RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI1 /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT Owners Manual 21 Installation HDMI HDMI

- HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."

- This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).

- This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i reso-

lution.

- When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI1/DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's output resolution to 1024x768, 60Hz.

- If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes both video and audio.

- If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.

<When the source device (DVD player or Set Top Box) supports HDMI>

How To Connect 1. Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product). 2. No separated audio connection is necessary. How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI or HDMI2 input source in main input option of SETUP menu.(Refer to P.59) VIDEO button is also available for this purpose.

<When the source device(DVD player or Set Top Box) supports DVI>

How To Connect 1. Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product). Do not use HDMI2 port for DVI connection if you want to connect audio. 2. A separated audio connection is necessary. 3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT. 4. If the source device has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.59) VIDEO button is also available for this purpose. 22 Plasma TV Reference Reference Cable sample Installation HDMI Cable

(not supplied with the product) HDMI to DVI Cable

(not supplied with the product) Fiber Optic Digital Audio Cable

(not supplied with the product) Analog Audio Cable(RCA type)

(not supplied with the product) Analog Audio Cable(Stereo to RCA type)

(not supplied with the product) Owners Manual 23 Installation How to use 1. Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET. 2. Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control. 3. Select HDM1/DVI Input source in Main Input option of SETUP menu.(Refer to P.62) 4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card. Notes:

- Depending on the graphics card, DOS mode may not work if you use a HDMI1 to DVI Cable.

- Avoid keeping a fixed image on the TV SET screen for a long period of time. The fixed image may become permanently imprint-

ed on the screen. Use the Orbiter screen saver when possible.

- When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen. As shown the lower picture, press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center.

- When Source Devices connected HDMI1/DVI Input output TV SET Resolution(480p, 720p, 1080i), TV SET Display fit EIA/CEA-

861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service center.

- In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. And In case of, Video Resolution not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center. POSITION G SIZE PHASE RESET Adjust Close F D E G In This Mode, the Supported TV SET Resolution Specification

- 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9

- 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)

- 704 x 480 P @ 59.94Hz / 60Hz, 16:9

- 704 x 480 P @ 59.94Hz / 60Hz, 4:3 In This Mode, the Supported PC Resolution Specification

- 640 x 480 @ 60Hz

- 640 x 480 @ 72Hz

- 640 x 480 @ 75Hz

- 800 x 600 @ 56Hz

- 800 x 600 @ 60Hz

- 800 x 600 @ 72Hz

- 800 x 600 @ 75Hz

- 1024 x 768 @ 60Hz(preferred format)

- 1024 x 768 @ 70Hz

- 1024 x 768 @ 75Hz 24 Plasma TV Installation TV Guide On Screen Setup TV Guide On Screen Setup

- The TV Guide On Screen system uses Setup information to provide you with show listings and lineups in your areawhich are updated several times a day.

- Once you set up the TV according to manufacturers instructions, you are ready to set up the TV Guide On Screen system. Note:The TV Guide On Screen system interactive program guide provides listings for cable-ready, cable box, and digital cable services as well as over-the-air broadcast. It does not provide listings for satellite services. How to connect VCR and Cable Box 1.Antenna Service 1.Antenna Service RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT AC INPUT REMOTE CONTROL CABLE ANTENNA S-VIDEO ANT OUT ANT IN OUT OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN S-VIDEO VCR Front VCR Rear 2. Cable Service without a Cable Box 2. Cable Service without a Cable Box RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT REMOTE CONTROL CABLE ANTENNA S-VIDEO AC INPUT ANT OUT ANT IN OUT OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN S-VIDEO VCR Front VCR Rear Owners Manual 25 Installation 3.Cable Service without a Cable Box 3.Cable Service without a Cable Box VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT Cable DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA or ANT OUT ANT IN OUT VCR Rear OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN S-VIDEO VCR Front Cable Box Front 4. Antenna and Cable Service without a Cable Box RF Cable OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO TV VCR Cable Box Rear IEEE-1394 HDMI 2 DVD

/DTV INPUT HDMI /DVI Cable VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA ANT OUT ANT IN OUT VCR Front S-VIDEO OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN VCR Rear 5. 5. Antenna and Cable Service with a Cable Box Antenna and Cable Service with a Cable Box VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT Cable DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA or ANT OUT ANT IN OUT VCR Front S-VIDEO OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN VCR Rear Cable Box Front RF Cable 26 Plasma TV OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO TV VCR Cable Box Rear Note:

The G-LINKTM cable is necessary for the TV Guide On Screen system to work with your Cable Box and VCR. See Page 23~24 for G-LINKTM connection instructions. Installation TV Guide On Screen Setup TV Guide On Screen Setup 1.Reminder Screen The TV Guide On Screen system's Reminder Screen appears:

-- after initial TV set up

-- if you power Off the TV and then power it back On To make a selection, use the D / E button to highlight to an option, and press ENTER.

"Set up TV Guide On Screen now," displays the Welcome Screen. Press ENTER to begin Setup.

"Remind me to set up later" returns you to watching TV.

"Don't remind me again" returns you to watching TV and stops the reminder screen from appearing upon power On. 2.Welcome Screen The TV Guide On Screen system's Welcome Screen appears:

-- by pressing the TV Guide key

-- when you power On your TV if you previously skipped "Set up TV Guide On Screen now" on the Reminder Screen. The Welcome Screen highlights features of the TV Guide On Screen system. Press ENTER to begin Setup. How to use 1. Screen 1: Country This screen asks you the location of your TV. Use the D / E button to highlight a country. Press ENTER to display Screen 2. Owners Manual 27 Installation 2. Screen 2: Enter Zip or Postal Code Option 1 If you selected USA in Screen 1, you see the ZIP Code screen. You input numbers by either pressing the number keys on the remote or using the D / E button to display a number, and then the F / G but-

ton to move to another field. Press ENTER to display Screen 3. Option 2 If you selected Canada in Screen 1, you see the Postal Code screen. You input characters by using the D / E button, and then the F / G button to move to another field. Press ENTER to display Screen 3. 3. Screen 3: Do you have Cable Service connected?

If you select Yes, you see Screen 4. If you select No, you see Screen 12. 4. Screen 4: Do you have a Cable Box?

If you select Yes, you see Screen 5. If you select No, you see Screen 12. 28 Plasma TV Installation 5. Screen 5: Which TV input is the cable box plugged into?

If you select Cable, you see Screen 6. If you make any other choice, you see Screen 7 . 6. Screen 6: Cable Box Tuning Channel Select the channel used for the cable box. Press ENTER to display Screen 7. 7. Screen 7: Cable Box Configuration Diagram The diagram shows the correct way to install the G-LINK Cable from the back of the device to the cable box. Make sure the G-LINKTM Cable is properly installed. Press ENTER to display Screen 8. Owners Manual 29 Installation 8. Screen 8: Cable Box Brand Name Use the D / E button to select a cable box brand. Press ENTER to display Screen 9. 9. Screen 9: Cable Box Preparation Follow the on-screen instructions, and press ENTER to display Screen 10. 10. Screen 10: Cable Box Code Testing When testing is done, Screen 11 displays automatically. 11. Screen 11: Cable Box Tuned to Channel 9?

If you select Yes, you see Screen 12. If you select No, a different code is tested in Screen 10. Note:

Many Cable Boxes require testing more than one code. If you select Test this code again, the same code is tested again in Screen 10. 30 Plasma TV 12. Screen 12: Do you have an antenna connected?

If you select Yes, you see Screen 13. Note:

If you selected No in Screen 3 then you must select Yes in this screen to receive a channel lineup and listings. If you select No, you see Screen 13. 13. Screen 13: Are your basic settings correct?

If you select Yes, you see Screen 14. If you select No, you see Screen 1. 14. Screen 14: Congratulations Press ENTER to display Screen 15. Installation Owners Manual 31 Installation 15. Screen 15: Helpful Information This screen tells you valuable information on using your Guide. Press ENTER to watch TV. Notes:

The TV Guide On Screen system receives program listings data through your cable or over-the-air video signal. In order to receive regular program listings, please remember to do the following:

1. Turn OFF your TV when it is not in use. (Do not unplug the power cord.) 2. If you have a Cable box connected, leave it ON. 3. If you have more than one Cable system in your area, you may be prompted to select which Cable systems program data to download. If so prompted, please follow the on-screen instructions. 32 Plasma TV Operation Operation Operation TTurning the TV On urning the TV On 1. First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the power, TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO, TV INPUT, CH (+, -), Number (0 ~ 9) button on the TV . 2. Select the viewing source by using TV/VIDEO, TV INPUT button on the remote control. This TV is programmed to remember which mode it was last set to, even if you turn the TV off. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. Notes:

If you intend to be away on vacation, disconnect the power plug from the wall power outlet. After turning on the TV, it takes time to be initialized for the TV Guide On Screen System. When the TV is turned on, blinks orange in standby mode, blinks green. And after orange stop the blinking, directly turn on the TV. But in case of green, screen is displayed at 3~4 minutes later. If power isnt turn on in red, contact your service center. Owners Manual 33 Operation HOME Menu HOME Menu

- The menus can be shown on the screen in the selected language. First select your language. Recorded TV Photo List Music List TV Guide TV Menu IEEE 1394 Schedule 34 Plasma TV TV Setup TV Setup Operation On-screen Menus Language Selection On-screen Menus Language Selection

- The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Advanced Aspect Ratio VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous G English Espaol Franais Owners Manual 35 Operation Setup Menu Options Setup Menu Options EZ Scan (Channel Search) EZ Scan (Channel Search)

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

- Run EZ Scan again after any Antenna/Cable connection changes. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select EZ Scan. 3. Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE. Manual Scan Manual Scan 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Manual Scan. 3. Press the G button and then use D / E button to select TV, DTV, CATV, and CADTV. 4. Press the G button and then use D / E button to select channel number you want to add or delete. 5. Press the ENTER button to add or delete for the channel number. 6. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Edit Set ID MENU Previous G Select channel type and channel number. TV 20 Notes:

This channel number is a physical channel number, which is different from normal channel number showed in Channel Edit. When a cable box connects to the physical channel 2,3 or 4 in TV Guide Setup, cable channels(CATV or CADTV) will not be scanned by EZ Scan or Manual Scan. When inserting the CableCARDTM, CATV, CADTV is not working in EZ Scan. TV: analog antenna(over-the-air) TV signal DTV: digital antenna(over-the-air) TV signal CATV: analog cable TV signal CADTV: digital cable TV signal 36 Plasma TV Operation Channel Edit Channel Edit

- Create two different types of channel lists in memory: Custom list and Favorite channel list from the default channel list created from the EZ Scan channel search.

- A custom list can be created by toggling each channel on or off with ENTER button. The. The channels in the Custom List are displayed in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen.You can create your own Favorite List. Use the FAV button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List. SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Edit Set ID MENU Previous G Selection ( G or ) leads you to the channel edit screen. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Channel Edit. 3. Press the G button. You will now see a screen filled with channel numbers and a preview picture. 4. Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV button to add the channel to the Favorite List. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note:

When Cable Box connect to RF2,3,4 in TV Guide Setup, CATV, CADTV is not working in EZ Scan. DTV Signal Strength DTV Signal Strength

- Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation.

- DTV Signals: Only when the input signal is DTV or CADTV, this function is available. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select DTV Signal. 3. View the on-screen signal strength monitor to see the quality of the signal being received. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owners Manual 37 Operation Setup Menu Options Setup Menu Options Channel Label Setup Channel Label Setup

- Choose preset labels for your channels.

If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel -

even if you didn't preset a label for the channel. SETUP EZ Scan VIDEO AUDIO TIME OPTION LOCK CABLE Manual Scan Channel Edit DTV Signal Channel Label G Main Input Sub Input Input Edit Set ID MENU Previous Selection ( G or ) leads you to the channel logo screen. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Channel Label. 3. Press the G button. You will now see a screen filled with Labels and a preview screen. 4. Use the CH +/- button to select a channel to Label. 5. Use D / E / F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to the selected channel. If you press ENTER button, you will see the channel banner.

Main Picture Source Selection Main Picture Source Selection

- Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Main Input. 3. Press the G button and then use D / E button to select the source: Antenna, Cable, Video, Front Video, Component1, Component2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Input Edit Input Edit 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Input Edit. 3. Press the G button and then use D / E button to select the source: Video, Front Video, Component1, Component2, RGB, HDMI1/DVI. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 38 Plasma TV SETUP VIDEO EZ Scan Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE G Main Input Sub Input Input Edit Set ID MENU Previous Antenna Cable Video1 Video2 Component1 Component2 RGB-DTV HDMI1/DVI HDMI2(VCR) SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Edit Set ID MENU Previous Video1 Cable Box Video2 VCR Component1 DVD Component2 Set Top Box G RGB PC HDMI1/DVI Game HDMI2 STB VVideo Menu Options ideo Menu Options EZ Picture EZ Picture

- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category. Operation

- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Custom.

- Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable. 1. Press the EZ PIC button repeatedly to select the picture appearance setup option as shown below:

Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports. You can also use the VIDEO menu to adjust EZ Picture. 2. Press the EXIT button to save and return to TV viewing. Manual Picture Control (Custom option) option) Manual Picture Control (

- Adjust the picture appearance to suit your preference and viewing situations. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select the desired picture option

(Contrast, Brightness, Color, Sharpness, or Tint ). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Color TTemperature Control emperature Control Color

- Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select Color Temperature . 3. Press the G button and then use D / E button to select either Cool, Medium or Warm. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. VVideo Reset ideo Reset

- Use to quickly reset all the Video menu options to their original factory preset values. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select Video Reset . 3. Press the G button to reset the Video menu options to original values. 39 Plasma TV SETUP VIDEO EZ Picture Contrast Brightness Color AUDIO Sharpness 85 50 50 50 G TIME OPTION LOCK CABLE 0 R G Tint Color Temperature Video Reset MENU Previous SETUP VIDEO EZ Picture Contrast Brightness Color AUDIO Sharpness TIME Tint Color Temperature G Cool OPTION Video Reset Medium Warm LOCK CABLE MENU Previous SETUP VIDEO EZ Picture Contrast Brightness Color AUDIO Sharpness TIME OPTION LOCK CABLE Tint Color Temperature Video Reset G Selection ( G or ) presets the video configuration. MENU Previous Owners Manual 39 Operation Audio Menu Options Audio Menu Options Audio Language Audio Language

- Other languages may be available if a digital signal is provided by the broad-

casting station. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select Audio Language. 3. Press the G button and then use D / E button to select: English, Spanish, or French. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. English Spanish French SETUP Audio Language G VIDEO AUDIO TIME OPTION LOCK CABLE EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Previous EZ SoundRite EZ SoundRite

- Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select EZ SoundRite. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Off On SETUP Audio Language EZ SoundRite G VIDEO AUDIO TIME OPTION LOCK CABLE EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Previous EZ Sound EZ Sound

- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content.

- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Custom.

- Normal, Stadium, News, Music, and Theater are preset for good sound quality at the factory and are not adjustable. 1. Press the EZ SOUND button repeatedly to select the appropriate sound setup as shown below:

Custom (your own settings), Normal, Stadium, News, Music, and Theater. You can also adjust EZ Sound in the AUDIO menu. 2. Press EXIT button to save and return to TV viewing. 40 Plasma TV

Operation Manual Sound Control (Custom option) option) Manual Sound Control (

- Adjust the sound to suit your taste and room situations. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select the desired sound option

(Balance, Treble, or Bass). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. L R G SETUP Audio Language EZ SoundRite VIDEO AUDIO TIME OPTION LOCK CABLE 0 50 50 EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Previous Front Surround Front Surround

is a trademark of SRS Labs, Inc.

- TruSurround XT technology is incorporated under license from SRS Labs, Inc.

- Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select Front Surround. 3. Press the G button and then use D / E button to select Off, 3D EchoSound System or SRS (Sound Retrieval System) TruSurround XT.. 3D EchoSound System Creates a stunning simulated stereo effects from any mono sound and a real-

istic three-dimensional sound with a very wide and deep sound stage into stereo sound. SRS TruSurround XT Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Audio Language EZ SoundRite VIDEO AUDIO TIME OPTION LOCK CABLE EZ Sound Balance Treble Bass Front Surround G Off TV Speaker BBE 3D EchoSound System SRS TruSurround XT MENU Previous Owners Manual 41 Operation Audio Menu Options Audio Menu Options TV Speakers On/Off Setup f Setup TV Speakers On/Of

- Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select TV Speaker. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Audio Language EZ SoundRite VIDEO AUDIO TIME OPTION LOCK CABLE EZ Sound Balance Treble Bass Front Surround TV Speaker G BBE Off On MENU Prev. Stereo/SAP Broadcasts Setup Broadcasts Setup Stereo/SAP

- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one.

- When having selected Stereo or SAP button on the remote control, this TV can only receive the signal in case that the TV sta-

tion transmits the proper signals.

- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

- Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting.

- Stereo or SAP can be received in Analog channel. 1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono, Stereo, or SAP appear in turn. If other languages available on the digital signal, select them with the SAP button. 2. Press EXIT button to save and return to TV viewing. BBEBBE

- BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select BBE. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press ENTER button to return to the previous menu. Manufactured under license from BBE Sound, Inc. SETUP Audio Language EZ SoundRite VIDEO AUDIO TIME OPTION LOCK CABLE EZ Sound Balance Treble Bass Front Surround TV Speaker BBE G MENU Previous Off On 42 Plasma TV Operation TTime Menu Options ime Menu Options Auto Clock Setup Auto Clock Setup

- The time is set automatically from a digital channel signal.

- The digital channel signal includes information for the current time provided by the broadcasting station.

- Set the clock manually, if the current time is set incorrectly by the auto clock function.

- When you set up TV guide on screen system, Auto Clock menu is not selected. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Auto Clock. 3. Press the G button and then use D / E button to select On. 4. Press the G button and then use D / E button to select your viewing area time zone: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Manual Clock Setup Manual Clock Setup If current time setting is wrong, reset the clock manually.

- When you set up TV guide on screen system, Manual Clock menu is not worked. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Manual Clock. 3. Press the G button and then use F / G button to select either the year, date, or time option. Once selected, use the D / E button to set the year, date, and time options. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Off On Time Zone Eastern Daylight Auto Saving SETUP Auto Clock G VIDEO AUDIO TIME OPTION LOCK CABLE Manual Clock Off Timer On Timer Sleep Timer Auto Off MENU Previous SETUP Auto Clock Manual Clock G Year - - - -

VIDEO AUDIO TIME OPTION LOCK CABLE Off Timer On Timer Sleep Timer Auto Off Date - - / - -

Time - - : - - - -

MENU Previous On/Off f TTimer Setup imer Setup On/Of

- Timer function operates only if current time has been set.

- Off-Timer function overrides On-Timer function if they are set both set to the same time.

- The TV must be in standby mode for the On-Timer to work.

If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Off Timer or On Timer. 3. Press the G button and then use D / E button to select On. To cancel On/Off timer function, select Off. 4. Press the G button and then use D / E button to set the hour. 5. Press the G button and then use D / E button to set the minutes. 6. For only On timer function Press the G button and then use D / E button to select the channel at turn-on. Press the G button and then use D / E button to set the sound level at turn-on. 7. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Auto Clock VIDEO AUDIO TIME OPTION LOCK CABLE Manual Clock Off Timer On Timer Sleep Timer Auto Off MENU Previous G Off On Time 6 : 30 AM Ch. TV 2-0 Vol 17 Owners Manual 43 Operation TTime Menu Options ime Menu Options Sleep TTimer imer Sleep

- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.

- You can also set up the Sleep Timer in the TIME menu. 1. Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. 2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the TV turns off, press the TIMER button once. 4. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off. Auto Offf Auto Of

If set to on and there is no input signal, the TV turns off automatically after 10 minutes. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Auto Off. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Auto Clock VIDEO AUDIO TIME OPTION LOCK CABLE Manual Clock Off Timer On Timer Sleep Timer Auto Off G Off On MENU Previous 44 Plasma TV Operation Option Menu Options Option Menu Options TimeShift Mode Setup

- Refer to the p.?

Cinema 3:2 Mode Setup

- Set up the TV for the best picture appearance for viewing movies. Off On SETUP Advanced G TimeShift Mode Aspect Ratio Cinema 3:2 Mode G Low Power LG Logo VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Cinema 3:2 Mode. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Low Power Low Power

- Low power reduces the plasma display power consumption. SETUP Advanced G Auto Buffering Cinema 3:2 Mode Low Power G LG Logo Off On Aspect Ratio VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Low power. 3. Press the G button and then use D / E button to select On or Off. When you select On, the screen darkens. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owners Manual 45 Operation Option Menu Options Option Menu Options LG Logo LG Logo

- This function is only applied TU-60PY22 model. SETUP Advanced G Auto Buffering Aspect Ratio Cinema 3:2 Mode Low Power LG Logo G Off On VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select LG Logo. 3. Press the G button and then use D / E button to select On or Off. When you select On, the Logo is lighting. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 46 Plasma TV Operation Aspect Ratio Control Aspect Ratio Control

- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be dis-

played. If you are viewing a picture with a 16:9 aspect ratio, you cant use the Horizon aspect ratio option.

- Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/HDMI1/DVI-DTV

(720p/1080i)/DTV(720p/1080i) input source.

- RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.

- Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. 1. Press the RATIO button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the OPTION menu. Set By Program Selects the proper picture proportion to match the sources image. (4:3 4:3, 16:9 16:9) 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. 16:9 Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. Horizon Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. Zoom 1 Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. Zoom 2 Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture tak-

ing a halfway trade off between alteration and screen coverage. Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted. You can adjust the enlarge proportion of Cinema Zoom using D / E button. The adjustment range is 1~16. Owners Manual 47 Operation Option Menu Options Option Menu Options Caption Caption 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Off On SETUP Advanced Aspect Ratio VIDEO Caption G AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous Caption/Textext Caption/T Analog Broadcasting System Captions

- Select a caption mode for displaying captioning information if provided on a program.

- Analog caption displays information at any position on the screen usually the program's dialog.

- Text displays information, usually at the bottom position and is used for a data service, generally not program related.

- Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.

- This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off. 1. Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. EZ Mute shows the selected captions option (if available on program) when the TV sound is muted

.2. Press EXIT button to save and return to TV viewing. You can also use the OPTION menu to select Caption/Text. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption/Text. 3. Press the G button and then use D / E button to select caption: CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Advanced Aspect Ratio VIDEO Caption Caption / Text G AUDIO Caption Option TIME OPTION LOCK CABLE Language ISM Method Front Display Auto Demo MENU Previous CC 1 CC 2 CC 3 CC 4 Text 1 Text 2 Text 3 Text 4 48 Plasma TV Operation Digital Broadcasting System Captions

- Choose the language you want the DTV/CADTV Captions to appear in.

- Languages can be chosen for digital sources only if they are included on the program. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption/Text. 3. Press the G button and then use D / E button to select available caption lan-

guages: English, Spanish, or French. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Advanced Aspect Ratio VIDEO Caption Caption / Text G AUDIO Caption Option TIME OPTION LOCK CABLE Language ISM Method Front Display Auto Demo MENU Previous English Spanish French Caption Option Caption Option

- Customize the DTV/CADTV captions that appear on your screen. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption Option. 3. Press the G button and then use F / G button to select Custom. 4. Use D / E button to customize the Style, Font, etc., to your preference. A pre-

view icon is provided at the bottom of the screen, use it to see the caption lan-

guage. Size: Set the size the words will appear in. Font: Select a typeface for the words. Text Color: Choose a color for the text. Text Opacity: Specify the opacity for the text color. Bg (Background) Color: Select a background color. Bg (Background) Opacity: Select the opacity for the background color. Edge Type: Select an edge type. Edge Color: Select a color for the edges. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Advanced Aspect Ratio VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option G Language ISM Method Front Display Auto Demo MENU Previous Style Custom Size A Standard Font Font 0 Text Color White Text Opacity Solid Bg Color Black Bg Opacity Solid Edge Type None Edge Color Black Owners Manual 49 Operation Option Menu Options Option Menu Options ISM (Image Sticking Minimization) Method ISM (Image Sticking Minimization) Method

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screen for a long period of time. SETUP Advanced VIDEO AUDIO TIME Aspect Ratio Caption Caption / Text Caption Option Language ISM Method G OPTION Front Display Auto Demo LOCK CABLE MENU Previous Normal White Wash Orbiter Inversion 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select ISM Method. 3. Press the G button and then use D / E button to select either Normal, White wash, Orbiter or Inversion . Normal If image sticking is never a problem, ISM is not necessary - set to Normal. White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move once per minute: Right Right Downside Downside Left Left Upside Upside. Inversion Inversion will automatically invert the plasma display panel color every 30 min-

utes. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Front LED (Light Emitting Diode) Display Front LED (Light Emitting Diode) Display

Illuminates brightly when the set is turned on. The LED displays current TV sta-

tus. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Front Display. 3. Press the G button and then use D / E button to select Off, Dark, Normal, and Bright. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Advanced VIDEO AUDIO TIME Aspect Ratio Caption Caption / Text Caption Option Language ISM Method OPTION Front Display G Auto Demo LOCK CABLE MENU Previous Off Dark Normal Bright 50 Plasma TV Auto Demo Auto Demo

- Displays the slide show to explain the main features of this TV. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Auto Demo. 3. Press EXIT button to stop Auto Demo. Operation SETUP Advanced VIDEO AUDIO TIME OPTION LOCK CABLE Aspect Ratio Caption Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous G Selection ( G or ) leads you to the demo. Owners Manual 51 Operation Lock Menu Options Lock Menu Options Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1. Set ratings and categories to be blocked. 2. Specify a password 3. Enablethe lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only. Ratings for Movies previously shown in theaters:

Movie Ratings :

Blocking Off G PG PG-13 R NC-17 X If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

(Permits all programs)

(General audience)

(Parental guidance suggested)

(Parents strongly cautioned)

(Restricted)

(No one 17 and under admitted)

(Adult only) Ratings for Television programs including made-for-TV movies :

(General audience)

(Parental guidance suggested)

(Parents strongly cautioned)

(Mature audience only)

(All children)

(Children 7 years older) TV-G TV-PG TV-14 TV-MA TV-Y TV-Y7 TV Rating Children:

Age Fantasy Violence TV Rating General:

Age Dialogue - sexual dialogue Language - adult language Sex - sexual situations Violence Input Block Video, Front Video

(On, Off) Component 1, 2

(On, Off) RGB, HDMI1/DVI,HDMI2 (On, Off)

(applies to TV-Y, TV-Y7)

(applies to TV-Y7)

(applies to TV-G, TV-PG, TV-14, TV-MA)

(applies to TV-PG, TV-14)

(applies to TV-PG, TV-14, TV-MA)

(applies to TV-PG, TV-14, TV-MA)

(applies to TV-PG, TV-14, TV-MA) 52 Plasma TV Operation Parental Lock Setup Parental Lock Setup

- Set up blocking schemes to block specific channels, ratings, and external viewing sources.

- A password is required to gain access to this menu if the Lock System is turned on. Off On SETUP Lock System G VIDEO AUDIO TIME OPTION LOCK CABLE Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Input Block MENU Prev.ious 1. Press the MENU button and then use D / E button to select the LOCK menu. Then, press the G button If Lock is already set, enter the password as requested. The TV is set up with the initial password 0-0-0-0. 2. Use the D / E button to choose from the following Lock Menu options. Once the option is selected, change the settings to your preference. Lock System: Activates or disables the blocking scheme you set up previ-

ously. Set Password: Change the password by inputting a new password twice. Movie Rating (MPAA): Blocks movies according to the movie ratings lim-

its specified, so children cannot view certain movies. You can set the rat-

ings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. TV Rating-Children: Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intend-

ed for mature audiences in the TV Rating - sub menu, your children can view those programs. TV Rating-General: Based on the ratings, blocks certain TV programs that you and your family do not want to view. Input Block: Enables you to select a source to block from the external source devices you have hooked up. 3. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note:

If you ever forget your password, key in 7, 7, 7, 7 on the remote control. Owners Manual 53 Home Menu Recorded TV Recorded TV

- When you press the button, HOME menu is displayed. From here, you can view the recorded program list.

- Or pressing the REC LIST button, you directly enter the recording list. 1. Select the Recorded TV in HOME menu or press the REC LIST button to view the recording list as shown below. A. B. 3. Select the desired folder in the folder list and then press the ENTER button to view the detailed menu. Create: Create new folder. Delete: Delete folder (except My TV). Rename: Edit folder name. Cancel: Close the detailed menu. C.C.

-> Use the D / E / F / G button to input the wanted name.

-> And then move the OK and press the ENTER button to save. 54 Plasma TV Home Menu D.D.

- The current thumbnail recorded list is shown above. 1. Use the CH +/- button to navigate thumbnail photo in pages. 2. Use MARK button to add or delete the marked photo to the mark list and only marked photos are toggling. 3. Use D / E / F / G button to navigate the appropriate thumbnail photo, then press the ENTER button to open the pop-up menu. Play: Begin playback of selected recording. Mark All: mark all photos on the screen. Unmark All: Change marked photos to unmarked photos. Move: Move program saved in HDD to the other folder. Through the 1394, can be record-

ed the desired program. When a device is not connected to the 1394 port, No DVHS Connected is dis-played on the screen. Delete: Delete the selected recording. This menu is only available in HDD mode. DVHS Out: When DVHS is connected, selected program is saved to the DVHS. Rename: Edit recorded name. Cancel: Close the Pop-up menu. 4. Repeatedly, press REC LIST button or EXIT button to return to TV viewing or press button to return to the previous menu. Owners Manual 55 Operation Using the Memory Card Using the Memory Card What is Memory Card What is Memory Card This is a device equipment to communicate the data between AV external equipment. Its used to a digital camera, camcorder, MP3 player, notebook or PDA. Precaution for Using the Memory Card Precaution for Using the Memory Card

- Insert the memory card correctly.

- Dont insert the metal substances into the slots of the memory card.

- Do not bend, drop or apply strong shock to memory card.

- After pulling the memory card out from the TV, please keep the memory stick in a appropriate case to prevent static shock.

- The stored data may be changed or lost as a result of misuse, static electricity.

- Do not turn the power off while using the memory card (loading or erasing).

- Dont eject the memory card while using the it. Otherwise, it may cause a data loss or card damage.

- Only Insert one card to each slot.

- To prevent a change or loss for stored data, dont mis-use the TV or dont let static electricity or electri-

cal noise for TV.

- This Company takes no responsibility for problems such as the damage or malfunction that occurs while using the TV set, inappropriate TV settings, or any other rea-sons, except for defects or mal-

functions intrinsic to the product.

- Ensure to use a memory card that lists the manufacturers name and serial number.

- The manufacturer shall not be responsible for damaged data. Be careful to avoid data damage, and back up your files.

- Make sure to comply with the following steps when ejecting a memory card. 56 Plasma TV Home Menu Entry Modes- 1.Using the Memory Card / 2. Enter the HOME Menu 1.Using the Memory Card How to insert and eject the Memory Card How to insert and eject the Memory Card A.A. WW Inserting a Card 1. Insert the Memory Card to Memory card slots of TV side panel, refer to the figure shown on the left. 2. Two slots support defferent types of the Memory Cards. 3. If Memory Card is not inserted, each slot is disable. WW Ejecting a card 1. Press the M/C EJECT button on the remote control. 2. Select the Memory 1 or Memory 2 based on the inserted card location. If selecting Cancel, OSD is disappeared. 3. Eject the card with the hand. Notes:

If you insert or eject a card in one slot while the card in another slot (slot 1 or slot 2) is in use, the product can run abnormally. Screen saver will be work if you dont eject the memory card with the hand after operating the eject function. Caution: Before you remove the memory card from the slot, do not forget to press the M/C EJECT button on the remote control and make it safe to eject the memory card, or the memory card may be damaged. label-side upward Memory Card type and Memory Card capacity Memory Card type and Memory Card capacity

- 9 types of Memory Card can be used for this Plasma TV.

- Playback speed can vary dependent on the card type. Slot 1 CF (CompactFlash) : 2GB MD (Microdrive) : 2GB CF+|| (magicstor) :2.2GB Slot 2 SD (Secure Digital) : 512MB MMC (MultiMedia Card) : 256MB MS (Memory Stick) :128MB MS Pro (Memory Stick Pro) : 1GB SMC (Smart Media Card) : 128MB XD (XD-Picture Card) : 512MB CompactFlash Microdrive magicstor xD-Picture Card MultiMediaCardTM TM Secure Digtal M E M O R Y S T I C K P R O S m a r t M e d a M E M O R Y S T I C K Owners Manual 57 WW Select the Photo or Music

- When you plug the Memory Card, this screen is displayed, automatically. B.B. C.C. 1. Press the F / G button to select Photo/Music. and use D / E button to select Slot1 or Slot2. 2. Press ENTER button to move Photo List/Music List of the each slot. (Directly move to p.41_pic.C)

- 2.Enter the HOME Menu Enter the HOME Menu Photo List Photo List

- When you press the button, HOME menu is displayed. Its available to play and copy the Photo file of Memory Card.or HDD. 1. In HOME menu, use D / E button and then use the ENTER or G button to select the Photo List . B.B. 2. Use D / E button to select the HDD/ Memory Card 1/

Memory Card 2 and then you will see a screen filled with thumbnail photos (pic.C,D). 58 Plasma TV Screen Components Screen Components Marked thumbnail photo number Current page/Total page Usable HDD Folder List C.C. Current page/Total page D.D. 3. Select the desired folder in the folder list and then press the ENTER button to view the detailed menu. Create: Create new folder. Delete: Delete folder (except My Photo' ).. Rename: Edit folder name. Cancel: Close the detailed menu. E.E.

-> Use the D / E / F / G button to input the wanted name.

-> And then select OK and press the ENTER button to save. Home Menu Owners Manual 59 Home Menu FF.. or

- As shown, up to current thumbnail photos listed per page. HDD mode Memory Card 1or 2 1. Use the CH D / E button to navigate in the thumbnail photo page. 2. Use MARK button to mark or unmark a photo. When one or more photos are marked, you can view or slide show only the marked ones. If no photo is marked, you can view or slide show all photos in the folder. 3. Use D / E / F / G button to navigate the appropriate thumbnail photos, then press the ENTER button to show the PopUp menu View: Display the selected item. Change from still image to slide show by pressing the PLAY (G) button. Slide Show: Start a slide show of all photos in the folder. The slide show state can be changed to the view state by pressing the Pause (||) button. Before start a slide show, you can choose the slide show interval (3,6 or 9 seconds). Mark All: Mark all photos on the screen. Unmark All: Unmark all marked photos. Move: Only HDD mode, move photo of this folder to another folder. Delete: Delete the selected thumbnail photo. This menu is only available in HDD mode. Send to: Copy the photo in the HDD to the Memory Card. This menu is only appeared in HDD. HDD Backup: Copy the photo in the Memory Card to the HDD. At this time, you can also make new folder. This menu is only available in Memory Card mode. Cancel: Close the pop-up menu. 4. Repeatedly, press EXIT button to return to TV viewing or press button to return to the previous menu. 60 Plasma TV Music List Music List A.A.

- When you press the button, HOME menu is dis-

played. Its available to play and copy the Photo / Music file of Memory Card.or HDD. 1. Use D / E button and then use the ENTER button or G button to select the Music List . B.B. 2. Use D / E button to select the HDD/ Memory Card 1/

Memory Card 2 and then you will see a list of music titles

(pic.C,D). C.C. D.D. 3. Select the desired folder in the folder list and then press the ENTER button to view the detailed menu. Create: Create new folder. Delete: Delete folder (except My Photo). Rename: Edit folder name. Cancel: Close the detailed menu. E.E.

-> Use the D / E / F / G button to input the wanted name.

-> And then select OK and press the ENTER button to save. Home Menu Owners Manual 61 Home Menu FF.. or

- As shown , up to 8 music titles are listed per page. Memory Card 1or 2 HDD mode 1. Use the CH D / E button to navigate in the music titles page. 2. Use MARK button to mark or unmark a music title. When one or more music titles are marked, the marked music will be played by turns. For example, if you want to hear only 1 music repeatedly, just mark the music only and play it. If no music title is marked, all the music in the folder will be played by turns. 3. Use D / E / F / G button to navigate the appropriate music titles, then press the ENTER button to show up the pop-up menu. Play: Play the selected music. Stop Play: Stop playback. With Photo: Start playing the selected music and then move to the Photo List. Mark All: Mark all music titles in the folder. Unmark All: Change marked musics to unmarked music titles. Move: Move music titles of this folder to another folder. Delete: Delete the selected music titles. This menu is only available in HDD mode. Copy: Copy the music titles in the HDD to Memory Card. This menu is only available in HDD mode. HDD Backup: Copy the music titles in the Memory Card to the HDD. At this time, you can also make new folder. This menu is only available in Memory Card mode. Cancel: Close the pop-up menu. 62 Plasma TV Home Menu 4. Repeatedly, press EXIT button to return to TV viewing or press button to return to the previous menu.

If you don't press any button for 40 seconds, the play information box(as shown in the below) will float as a screen saver.

(a) For example :

Note:

When music is playing, is displayed in front of the music title. Press any button except VOL D / E , MUTE, Play (G), Pause (||), Stop (V),Skip Next and Skip Previous ( FF, GG ) but-

tons, to stop the screen saver. Play (G), Stop (V), Pause (||), Skip Next and Skip Previous ( FF, GG ) buttons on the remote control are also available in this mode. Owners Manual 63 Operation TTimeShift imeShift TTimeShift Mode imeShift Mode

- This function allows the unit to automatically record live TV and make it available for reviewing at any time. With Auto Buffering turned on, you may pause and rewind normal TV viewing at any time without missing any of the live broadcast. SETUP Advanced G Auto Buffering G Aspect Ratio Cinema 3:2 Mode Off On Low Power LG Logo VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous 1. Press the Menu button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Advanced. 3. Press the G button and then use D / E button to select the Auto Buffering. 4. Press the G button and then use D / E button to select On or Off. W W Progressing the Timeshift function 1. When turning the TV on, Timeshift function is progressing . As soon as Timeshift starts, a progress bar indicating current recording status is displayed in the bottom of the screen. ( Timeshift Progress Bar is shown below) Press the EXIT button to hide the Progress Bar. Pressing the ENTER button will display the 'Progress Bar'. Stay The TimeShift even change a channel on Timeshift. 2 4 1 3 5

* The Progress Bar?

This function indicates a possible PVR reshowing section ,a cur-

rent on-screen and real on-

broadcasting position, a section of section-recording. 1. Indicates status of current displayed video. 2. Indicates current save time. 3. Indicates 15 minute intervals from Timeshift start time. (Total - one hour). 4. Indicates Timeshift elasped time. 5. Indicates current Timeshift position. 64 Plasma TV Operation 2. When finishing the Timeshift function, enter the Menu and then Timeshift Mode is to be Off. Notes:

PVR (Personal Video Recorder) : A device which records and plays broadcast program contents onto a hard disk in TV or SET TOP BOX. When the TimeShift closes, the file (min. 10 seconds) is automatically stored in the record list. If available hard-disk space is low when TimeShift is initiated, It will disappear automatically from the oldest part. In order to save hard-disk space, no storage is done when there is no signal. The total storing space of hard-disk is160GB, there are 4GB minimum reserved for TimeShift. When turning power on, it may take up to 3 minutes to initialize the HDD. The TimeShift function will not initiate for a copy-protected program. Because an analog broadcast is transfered to a digital signal, video that contains rapid movement may show "cross stripes". This happen when the analo signal is compressed and then retored in the digital signal. The unit will attempt to soften the video in order to reduce this effect of excessive picture noise. When using the PIP/POP mode, TimeShift is stopped. W W On progressing the Timeshift, play

- On progressing Timeshift, It can do a diversified playing . Indicates that he current broadcast and displayed video differ. 1. You can shift playback to any point within the recording time . When playing, press the REW (FF ) or FF (GG) button. Searching speed changes with each press of the button. Like -> -> -> -> in a row. 2 times 5 times 20 times 50 times 300 times If the button is pressed continuously, it changes like above. If the button is taken away, it changes a nor-

mal playing. During playback, press the Pause ( II ) button. Still screen is displayed. Repetedly press the Pause ( II ) button to advance frame by frame. If you wish to return to the current live broadcast, press the GG button. (Indicator will change to LIVE) 2. Press the PLAY ( G) button to return to normal play. Owners Manual 65 Operation Recording Recording

- This function is able to record channel watched on main screen of an Analog or Digital broadcasting. W W Instant Record

- This function records the currently displayed channel. 1.Select the desired channel to record while watching program. 2. Use the F / G button to select the OK ( as illustrated pic.A.) or Options or Stop Record. If you select the OK or press the RECORD () button in the TV mode, recording will start as marking , and recording will begin with basic settings. A. 3. You can select the Stop Record to stop the recording. 4. You can set the duration of the recording by selecting Options and then ENTER button, then the recording time is dis-

played. Press the F / G repeatedly to adjust the recording length. Each press of F / G button changes the recording duration in the sequence shown below. No Limit -> 30min -> 1hour -> 1hr 30min -> 2hr -> 2hr 30min -> 3hr B. 66 Plasma TV Operation 4. You can also add recording time by pressing the RECORD () button during the Instant Record. Press the F / G repeat-

edly to add to the recording time. Each press of F / G button changes the recording duration in the sequence shown below. basic value-> +10min -> +20min -> +30min -> +40min ->+50min -> +1hr The extra recording time added to existed setting value makes final recording time length. C. 5. After adjusting the recording time, select OK and the progress bar will be displayed. Total record-

ing duration Elapsed recording time Press the EXIT button to hide the Progress Bar. Press the ENTER button to display the progress bar. 5. Press the STOP ( V ) to stop recording, or, when the recording duration is reached, the HD DVR will stop recording and power off. Although recording has stopped, the Timeshift features remain active. Notes:

When recording, if the available storage space becomes low, the recording will be automatically end. Once recording has finished, " A recording is finished, will you put the power off?" will be displayed. If power is interrupted or turned off too soon after recording, the program may not be saved. Therefore, first press the

( V ) button and confirm the recording list, before powering the unit off. If you press the POWER button while recording, the Screen Saver will initiate and recording will continue.(However, if recording with the duration set to [no limit], recording will stop and the unit will power off.) Recordings of less than 10 seconds will not be saved. To save the disk space while recording a digital screen, no data is saved when no signal is present. The recording function will not initiate for a copy-protected program. Owners Manual 67 W W Watching & Record

- While recording, you can change channel s or inputs, without disturbing the recording. The program being recorded will show in the lower-right corner of the main screen. 1. After starting an Instant Recording or Reserved Recording, change the channel or input Check screen of recording is shown in the lower-right corner the screen (as shown below). Pressing the PIP button will toggle the check screen on or off. Pressing the SWAP button will return the main screen to display the program being recorded. In order to change the channel being recorded, Instant Record or Reserved Record s must be stopped. screen being recorded Watch & Record Input port Record Watch Digital Analog Video1 Video2 Component1 Component2 RGB-PC/DTV DVI-PC/DTV Digital Analog Video1 Video2 X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Note: When digital broadcast is being recorded, another digital broadcast can not be tuned. 68 Plasma TV TV Guide On Screen System TV Guide On Screen System System TV Guide On Screen Overview Overview

- Your new TV contains the TV Guide On Screen Interactive Program Guide.

- The TV Guide On Screen system has features that help you get the most out of your viewing experience. TV Guide On Screen Overview The TV Guide On Screen system has the following features:

Eight days of show listings (today plus seven days). Icons that indicate show rating, stereo, HDTV, new episode, etc. Intuitive up/down/left/right navigation using your remote control. Set shows to Record. Schedule show Reminders. Search shows by category (e.g., Movies, Sports, Children, etc.). Search for shows based on keywords or alphabetically by title. Direct tuning to a channel. Show information while watching TV. Streamlined System Setup and default setting options. Channel lineup customization. Help screens while in the Guide. Owners Manual 69 TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System Screen Components Screen Components

- The screens displayed in the TV Guide On Screen system share many of the same compo-

nents, as shown in the following figure:

Video Window - displays TV video while the Guide is displayed Service Bar - provides access to the 4 main Guide Services Current Service Label - indented to indicate current Service displayed Tile - displays show title Highlight - indicates an active tile Info Box - provides information for a highlighted item Info Button - cycles through the various Info Box sizes Channel Logo - identifies network Record/Remind Icons - indicates a show is set to Record or set as a Reminder Panel Ad - location where show- or product-specific information appears (and also where Panel Menu appears) 70 Plasma TV TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen Panel Menu Panel Menu Default Command Button Hightlight Entry Box Odometer A Panel Menu appears when the Menu key is pressed on a highlighted tile and additional options are available. It also appears when you press ENTER on a show starting in the future. When a Panel Menu appears, the highlighted tile changes color to indicate the Panel Menu relates to this tile. The Panel Menu displays below the Video Window. Help is available for a displayed Panel Menu by pressing the INFO button. The D / E button move between the options within the Panel Menu. The left and right arrows move to adjacent options unless the highlight is on an odometer, where these arrows change the odometer choice. Pressing ENTER from an odometer or number entry box moves the highlight to the default command button of that Panel Menu, for example, Schedule Reminder. Pressing ENTER from a highlighted command button executes the action and closes the Panel Menu (e.g., Schedule Reminder, Cancel). Select Cancel to cancel any changes and press ENTER to close this menu. Pressing Menu is a shortcut to Cancel. Press Menu to cancel any changes and close the menu. If a Panel Menu contains more menu options than can be displayed on a single screen, D / E button appear at the top or bottom of a menu. Simply scroll down to access these options. Owners Manual 71 TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System Main Services Main Services V < Listings >

- Access Listings by pressing the TV Guide button on your remote or on the front panel of your TV.

- Listings is always the first Service displayed in the Guide.

- With Listings highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen. Use the D / E / F / G buttons to move the highlight within Listings to:

View 8 days of show listings Read show descriptions Tune directly to a show currently airing Set a show to Remind Set a show to Record Lock and unlock the Video Window Access Panel and Channel Ads Notes: There may be times when the TV Guide On Screen system could display partial or no program list-

ings. The reasons for this include:

Program schedule information was not provided to TV Guide On Screen. The transmission of the program listings was inter-

rupted. The phrase No Listings will be replaced with program information during the next transmission, which should occur within the next 24 hours. Please remember to turn off your TV when not in use in order to receive program listings. 72 Plasma TV TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen V < Search >

- Search lets you find shows by category (Alphabetical, Movies, Sports, Children, Educational, News, Variety, Series, HDTV) or by Keyword.

- With Search highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen. Category Search Example: Movies 1. From Search, use the E button to highlight Movies. Owners Manual 73 TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System 2. Use the E button to highlight a subcategory (for example, All). 3. Press ENTER to display a list of all Movies, organized by date and time. 4. Highlight a show and press ENTER to watch (if on now) or the Menu key to display the Episode Options menu. You can choose to set a recording, a reminder, or tune to the channel. Go to Service Bar - closes the menu, changes no infor-

mation, and returns to the Search Service Bar. Tune to Channel - exits the Guide and tunes to the chan-

nel of the highlighted show (show airs in the future). Note: This option reads Watch Now if the show is cur-

rently airing. Set Recording - displays the Record Options menu, from which you can set frequency, start and end time, etc. Set Reminder - displays the Remind Options menu, from which you can set frequency, when, automatically power On, and auto-tune the TV. Cancel - closes the menu, changes no information, and returns to the highlighted show. 74 Plasma TV TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen Keyword Search

- Keyword search lets you enter a word(s) to look for a particular show by category or for every show title that matches. 1. Highlight the Keyword navigation label, and press ENTER button to display the Keyword Search menu. 2. Highlight New Search, and press ENTER button. 3. The Search Options menu is displayed. 4. Highlight Category, and use the F / G button to select a category to search (e.g. All, HDTV, Children, Sports, etc.). When finished, use the E button to highlight Enter Keyword. 5. Highlight Enter Keyword, and press ENTER. Then the keyboard is displayed. 6. Use the D / E / F / G button to highlight a character, and press ENTER to display it. When complete, high-

light Done and press ENTER. Owners Manual 75 TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System 7. A list of all matching shows for that keyword is dis-

played. Like the Category Search Example, you can highlight a show, and press ENTER to display all airings. You can then highlight a specific listing and press ENTER to watch (if On now) or the Menu key to display the Episode Options menu. From the Episode Options menu, choose to set a recording, a reminder, or tune to the channel, as pre-

viously described. The TV guide on screen system stores all the keywords you create. To edit or delete a keyword, highlight the keyword and press the Menu key. A Search Options menu is displayed. Go to Service Bar - closes the menu, changes no infor-

mation, and returns to the Search Service Bar. Edit Search - displays the keyboard, where you can change the keyword. Delete Search - A Confirm menu is displayed. Yes - deletes the Search No - closes the panel menu Cancel - closes the menu, changes no information, and returns to the highlighted show. 76 Plasma TV TV Guide On Screen System continued System continued TV Guide On Screen V < Recordings >

Recordings displays a list of previously recorded or currently recording shows on a DVR or the currently inerted DVD in a DVD recorder. With Recordings highlighted, press the INFO button to display a Help screen. Press the INFO button again to close the screen. Choose the way Recordings are displayed by highlighting Recordings on the Service Bar and then press the MENU button to display the Recordings Options menu. Use the D / E buttons to choose between the following:

In View As, use the F / G buttons to choose between W Group - recorded shows are listed without listing every recorded episode (see example in Screen A) W List - displays a complete list of every recorded episode for a show(see example in Screen B) Screen A In Sort By, use the F / G buttons to choose between W Title - shows are displayed in alphabetical order (see example in Screen A) W Date - shows are displayed by date and time, with most recent date and time first (see example in Screen B) When finished, press ENTER to hightlight Done. Press ENTER again to close the menu and display the Recordings with the selected options. In List View, highlight an episode and ab Info box provides show information. Press the MENU button to display the Episode Options menu. In Group View, highlight a show and press ENTER to view a summary for the all the recorded shows along with the episode list (pres ENTER again to collapse the episode list). Highlight a specific episode and press the MENU buttos to display the Episode Options menu. Screen B Owners Manual 77 TV Guide On Screen System continued System continued TV Guide On Screen To view an episode, you can do one of the following:

highlight an episode, and press ENTER to view it now. The episode either starts from where it was last stopped(if viewed previously) or from the brginning. W Go th Service bar - close the menu, changes no infor-

mation, and returns to th Schedule Service Bar. W Resume - starts from where it was last stopped(if viewde previously) or from the beginning. W Play from Beginning - starts from the beginning, even if stopped previously. W Delete Episode - deletes the episode from the Recordings, A Confirm menu is displayed. W Yes - deletes the episode. W No - closes the panel menu. W Cancel - closes the menu, changes no information, and returns to the highlighted show. 78 Plasma TV TV Guide On Screen System continued System continued TV Guide On Screen V < Setup >

- After you initially complete Guide Setup, you can make changes to Guide settings in the following areas:

TV Guide On Screen System Change System Settings Change Channel Display Change Default Options Highlight a choice, press ENTER, and follow the on-screen instructions. With Setup highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen. Change System Settings This option appears after you have completed the initial Guide Setup process. Press ENTER to display the Confirming Your Settings screen. You see your current settings. Choose one of the options, press ENTER, and follow the on-

screen instructions. Owners Manual 79 TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen Change Channel Display Change Channel Display lets you edit channel information that appears in Listings. With Change Channel Display you can :

Re-order the position or the channel appears in Listings Change the tune channel number Switch a channel W On - the channel is always displayed W Off - the channel is never displayed W Auto-Hide - the channel is only displayed when program information is available. Press ENTER to display the Channel Editor screen. Then, highlight a channel and press Menu. A Grid Options menu is displayed. Highlight Go Back to Setup to close the menu, change no information, and return to the Setup Service Bar. Or make changes and when finished, press ENTER to high-

light Done. Press ENTER again to close the menu and accept the changes. Highlight Cancel to close the menu, change no information, and return to the highlighted channel. 80 Plasma TV

TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System Change Default Options Change Default Options lets you change default settings in the following categories:

General Default Options Record Defaults Remind Defaults Highlight Change Default Options, and press ENTER.

<General Default Options>

General Default Options lets you set defaults for the following:

The initial Info Box size when the TV guide on screen system is entered. Choices are No, Small, Large, and Last Used

(Default = Last Used). The Info Box size rotation when the Info key is pressed while in the TV guide on screen system. Choices are No only, Small only, Large only, No & Small, No &

Large, Small & Large, All (Default = All) Automatic entry into the TV guide on screen system (Auto-Guide) when the TV is powered On. Choices are On and Off (Default = On). Highlight General Default Options, and press the Menu key to dis-

play the General Default Options menu. Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar. When finished, press ENTER to highlight Done. Press ENTER again to close the menu and accept the changes. Highlight Cancel to close the menu, change no information, and return to the highlighted option. Owners Manual 81 TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen

< Record Defaults>

Record Default Options lets you set defaults for the following:

When to start the record event. Choices are 120 minutes early to 120 minutes late, to On time. (Default = On time) When to end the record event. Choices are 120 minutes early to 120 minutes late, to On time. (Default = On time) Recorder choice: Please choose the HDD only. This TV does not provide other devices with a recording feature. Highlight Record Defaults, and press the Menu key to display the Record Default Options menu. Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

< Remind Defaults>

Remind Default Options lets you set defaults for the following:

Power On the TV, if Off, when a Reminder is scheduled. Choices are Yes and No.

(Default = No) Automatically tune the TV to the channel (TV must be On), when a Reminder is scheduled. Choices are Yes and No.

(Default = No) When to display the reminder screen. Choices are 30 seconds to 15 minutes early, to 30 seconds to 15 minutes late, to On time.

(Default = 1 min early) Highlight Remind Defaults, and press the Menu key to display the Remind Default Options menu. Highlight Go to Service Bar to close the menu, change no information, and return to the Setup Service Bar. When finished, press ENTER to highlight Done. Press ENTER again to close the menu and accept the changes. Highlight Cancel to close the menu, change no information, and return to the highlighted option. 82 Plasma TV TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System Record And Remind Features And Remind Features Record V < Record >

You can set a show to Record in Listings, Search, and Schedule or change Record settings for a show in Schedule. There are 3 ways to set a show to Record:

W Once records the show one time W Regularly records the show every time the show airs on the same channel and starts at the same 1) Using the Record Button on the Remote time Press the Record button on the remote to record the show Once with current default settings (Start and End recording On Time). Each time you press the Record button, you change the record frequency (but not the default settings) among Once (default), Regularly, Daily, Weekly and then Cancel. Note: The proper Record icon appears on the show tile, as the W Weekly records the show each time the show airs on the same day of the week, on the same channel and starts at the same time W Off (not cancel) keeps the show in the list but will not record this show until the frequency is changed Record button is pressed. W Cancel (no icon displayed)does not record 2) From a Panel Menu Highlight a show, and press Menu to display the Episode Options menu. Highlight Set Recording, and press ENTER to display the Record Options menu. Highlight the Frequency option, and use the left and right arrows to choose among Once, Regularly, Weekly, and Off, as previously described. Recorder choice: Please choose the HDD only. This TV does not provide other devices with a recording feature. Note: Video Window Lock is operated to on or off using PIP button in Listings mode. Owners Manual 83 TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen When finished, press ENTER to highlight Schedule Recording. Press ENTER again to close the menu. You see a Record icon for the selected frequency next to the show title. Highlight Cancel to close the menu, change no information, and return to the highlighted show. 3) Manual Recording Highlight the Schedule Service label, and press Menu to display the Schedule Options menu. Use the D / E / F / G buttons to move through the options. Use the number or Use the D / E / F / G buttons to change the infor-

mation, as necessary. Highlight New Manual Recording and press ENTER to display the Record Options menu. Current information (i.e., date, start and end times, channel, input) is displayed. Recorder choice: Please choose the HDD only. This TV does not provide other devices with a recording feature. 84 Plasma TV TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System Use the left and right arrows to choose between Once, Daily, Weekly, and Off, as follows. W Once records the time, channel, input, recorder combi-

nation one time. W Daily records the time, channel, input, recorder combi-

nation Monday through Friday. W Weekly records the time, channel, input, recorder com-

bination once a week on this selected day of the week W Off (not cancel) keeps the time, channel, input, recorder combination in the list without recording until the frequency is changed. When finished, press ENTER to highlight Schedule Recording. Press ENTER again to close the menu. You see a Record icon for the selected frequency next to the show title. Note: Manual recording is listed by channel number. Highlight Cancel to close the menu, change no informa-

tion, and return to the highlighted show. Before a recording begins, a notification screen appears if you are using a Cable box and your TV is On. At that time, you can choose to start or cancel recording. If the TV is not On, the recording occurs as scheduled. If there is no activity for 3 minutes, the notification screen auto-

matically closes and completes the highlighted item. Record Conflict A conflict message appears for the following reasons:

a show set to Record overlaps with any part of another show pre-

viously set to Record, a show set to Record overlaps with a show previously set to auto-

tune Select one of these options:

W record anyway - this show will override an existing show set to Record or auto-tune W don't record this show - cancel the Recording Owners Manual 85 TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen V < Remind >

You can set a show Reminder in Listings, Search, and Schedule or change Reminder settings for a show in Schedule. There are 2 ways to set a show Reminder:

1) From a Panel Menu Highlight a show, and press Menu to display the Episode Options menu. Highlight Set Reminder, and press ENTER to display the Remind Options menu. Highlight the Frequency option, and use the left and right arrows to choose between:

W Once sets a show reminder one time W Regularly sets a show reminder every time the show airs on the same channel and starts at the same time W Weekly sets a show reminder each time the show airs on the same day of the week, on the same channel and starts at the same time W Off keeps the show in the list but will not remind until the frequency is changed Power On the TV, if Off, when a Reminder is scheduled. Choices are Yes and No. (Default = No) Automatically tune the TV to the channel (TV must be On), when a Reminder is scheduled. Choices are Yes and No. (Default =

No) When to display the reminder screen. Choices are 30 seconds to 15 minutes early, to 30 seconds to 15 minutes late, to On time.

(Default = 1 min early) When finished, press ENTER to highlight Schedule Reminder. Press ENTER again to close the menu. You see a Remind icon for the selected frequency next to the show title. Highlight Cancel to close the menu, change no information, and return to the highlighted show. 86 Plasma TV TV Guide On Screen System continued System continued TV Guide On Screen TV Guide On Screen System 2) Manual Reminder Highlight the Schedule Service label, and press the Menu key to display the Schedule Options menu. Use the D / E / F / G buttons to move through the options. Use the number or D / E / F / G buttons to change the information, as necessary. Highlight New Manual Reminder and press the ENTER key to display the Remind Options menu. Current information (i.e., date, start and end times, channel, input, frequency, etc.) is displayed. Highlight the Frequency option, and use the F / G buttons to choose among Once, Daily, Weekly, and Off, as follows. W Once sets a show reminder for the time, channel, input, recorder combination one time W Daily reminds for the time, channel, input, recorder combination Monday through Friday W Weekly sets a show reminder for the time, channel, input, recorder combination once a week on this selected day of the week W Off (not cancel) keeps the time, channel, input, desti-

nation combination in the list without reminding until the fre-

quency is changed Power On the TV, if Off, when a Reminder is scheduled. Choices are Yes and No (Default =No). Automatically tune the TV to the channel (TV must be On), when a Reminder is scheduled. Choices are Yes and No

(Default = No). When finished, press ENTER to highlight Schedule Reminder. Press ENTER again to close the menu. You see a Remind icon for the selected frequency next to the show title. Note: Manual reminder is listed by channel number. Highlight Cancel to close the menu, change no information, and return to the highlighted show. Owners Manual 87 TV Guide On Screen System TV Guide On Screen System continued System continued TV Guide On Screen Based on your option settings, a notification screen will appear, if your TV is On at the reminder time. You can then choose to hide the reminder, or highlight the show, and press ENTER to tune to the show. If there is no activ-

ity for 3 minutes, the notification screen automatically closes and completes item (hide reminders). the highlighted If you choose Hide Reminders, the window closes for the show or shows, but does not affect other Reminders you set. Note: If more than 2 reminders are set for the same time, arrows appear on the Reminder screen. Use the D / E buttons to view the shows. Remind Conflict A conflict message appears for the following reasons:

a show set with an Auto-Tune Reminder has the same start time as an existing Auto-Tune Reminder. If you are using a cable box, a show set with an Auto-

Tune Reminder overlaps with a Recording already scheduled. Select one of these options:

W auto-tune anyway - this show will override an exist-

ing show set to auto-tune W proceed, no auto-tune - set the show as a Reminder but do not auto-tune W don't set this reminder - cancel the Reminder 88 Plasma TV Schedule Functions Schedule Functions Schedule Schedule

- Schedule lets you review, edit, or delete Record and Remind events that you set previously.

- With Schedule highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen.

- An icon identifies the event type:

Record W Once records the show one time W Regularly , Daily records the show every time the show airs on the same channel and starts at the same time W Weekly records the show each time the show airs on the same day of the week, on the same channel and starts at the same time W Off keeps the show in the list but will not record this show until the frequency is changed. Remind W Once sets a show reminder one time W Regularly , Daily sets a show reminder every time the show airs on the same channel and starts at the same time W Weekly sets a show reminder each time the show airs on the same day of the week, on the same channel and starts at the same time W Off keeps the show in the list but will not remind until the frequency is changed Highlight an event, and press the Menu key for options. Go to Service Bar - closes the menu, changes no information, and returns to the Schedule Service Bar. Tune to channel - exits the tv guide on screen system and tunes to the highlighted show. Delete Recording - removes the recording from the Schedule, after a Confirm screen. Edit Recording - opens a menu from which you can change existing recording information. Set Reminder - opens a menu from which you can set a Reminder for the show (Record is not cancelled). Cancel - closes the menu, changes no information, and returns to the highlighted show. Owners Manual 89 IEEE 1394 IEEE 1394 Functions IEEE 1394 Functions IEEE 1394 IEEE 1394

- It's available to communicate to either direction and you can give and take a image, sound, or each control command with one cable.

- Only use the DVHS and MicroMV Camcorder to work the 1394. How to connect the 1394 To work the 1394, this 3 methods can used. 1. When connecting the DVHS or the MicroMV Camcorder, as shown in the (a) or (b) figure, select the IEEE 1394 in HOME menu to show the control panel.

(a) TV DVHS

(b) TV MicroMV Camcorder

<Connect the IEEE1394 Cable>

<Connect the IEEE1394 Cable>

<DVHS>

<MicroMV Camcorder>

<TV>

<TV>

2. When connecting the DVHS and the MicroMV Camcorder, as shown in the (c) figure, select the IEEE 1394 in HOME menu to show the contents panel and then select the DVHS or the MicroMV Camcorder to show the control panel.

(c) TV DVHS + MicroMV Camcorder

<Connect the IEEE1394 Cable>

<DVHS>

<TV>

<MicroMV Camcorder>

<Connect the IEEE1394 Cable>

When connecting the 1394 and then playing, you must use the original DVHS tape. If not, it may be occurred the errors. 90 Plasma TV IEEE 1394 IEEE 1394 functions continued IEEE 1394 functions continued DVHS DVHS VHow to play the DVHS 1. Connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the DVHS with IEEE 1394 Cable. 2. When watching the TV, press the button to move the IEEE 1394 in HOME menu and then ENTER button.

<DVHS>

<TV>

2. Press the D / E buttons to select the DVHS and then use the ENTER button. Show the control panel of DVHS. The control panel of DVHS

-Depending on the connected equipment, marked control panel may differ. 3 4 5

* Supported DVHS List 6 7 8 9 1. DVHS Company 2. DVHS Model 3. Connected Equipment to the 1394 4. DVHS Operating Status 5. Power On/Off 6. DVHS Play Time 7. Tape Status Tape shape Icon - Tape in or not Lock shape Icon - Use or not use VICTOR(HM-DH35000U) JVC(HM-DH30000U) JVC(HM-DH40000U) MITSUBISHI(HS-HD1100U) MITSUBISHI(HS-HD2000U) Hitachi(DT-DR20000) Hitachi(DT-DRX100) PANASONIC(NV-DH1) PANASONIC(NV-DH2) PANASONIC(NV-DHE20) TOSHIBA(A-HD2000) 8. Initializing Play Time 9. DVHS Play, Pause, Stop, Search or Skip

(Notes:

Skip- This function is for a fast search. It searches the programs start point and then plays. On skipping, Search (GG, FF), Rec(") Pause ( ) and Play (G) are displayed on the Control Panel. In some models, its not available to operate the Skipping ( FF, GG ) function. Owners Manual 91 IEEE 1394 functions continued IEEE 1394 functions continued VHow to play the instant reecord to the DVHS 1. When watching the TV, press the button to move the IEEE 1394 in HOME menu and then ENTER button. 2. Press the D / E buttons to select the DVHS and then use the ENTER button. Show the control panel of DVHS. 3. Press the D / E / F / G buttons to move to " and then use the ENTER button. You can record the current program to the DVHS. 4. Press the D / E / F / G buttons to move to # and then use the ENTER button. Show the control panel of DVHS. The instant record function couldnt use copy-protected programs. 92 Plasma TV IEEE 1394 functions continued IEEE 1394 functions continued VHow to save the DVHS to the DVR 1. On playing the DVHS, press the D / E / F / G buttons to move to DVR $ and then use the ENTER button. Save the current screen to the DVR. 2. Press the D / E / F / G buttons to move to DVR # and then use the ENTER button to end a saving. When you save the program which is copy - protected to the PVR, This tape is copy-protected is display on the screen and dont save to the PVR. Owners Manual 93 IEEE 1394 functions continued IEEE 1394 functions continued VHow to save the DVR to the DVHS 1. When press the button, record list is dis-

played. You can select the wanted program by pressing the D / E / F / G buttons. And then press the ENTER button. 2. Select the DVHS Out by pressing the D / E / F / G buttons and then press the ENTER button. 3. Press the D / E buttons to select the wanted device and move to the Record 4. Press the D / E / F / G buttons to move to the START and then press the ENTER button to save to DVHS. 5. Press the F / G buttons to move to the STOP and then press the ENTER button to stop a saving. By pressing the RESUME button, you can con-

tiously save the recorded contents from a point of stopping time. The copy-protected contents couldnt save to the DVHS. 94 Plasma TV IEEE 1394 IEEE 1394 functions continued IEEE 1394 functions continued MicroMV Camcorder MicroMV Camcorder How to play the MicroMV Camcorder E.E. 1. Connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the MicroMV Camcorder with IEEE 1394 Cable. 2. When watching the TV, press the button to move the IEEE 1394 in HOME menu and then ENTER button.

<MicroMV Camcorder>

<TV>

2. Press the D / E buttons to select the Camcorder and then use the ENTER button. Show the control panel of DVHS. The control panel of MicroMV Camcorder

-Depending on the connected equipment, marked control panel may dif-

fer. 3 4 5 6 7 8 1. MicroMV Camcorder Company 2. MicroMV Camcorder Model 3. Connected Equipment to the 1394 4. MicroMV Camcorder Operating Status 5. MicroMV Camcorder Play Time 6. Tape Status Tape shape Icon - Tape in or not Lock shape Icon - Use or not use 7. MicroMV Camcorder Play, Search or Stop 8. Initializing Play Time

* Supported MicroMV Camcorder List SONY MICORMV IP-5 SONY MICORMV IP-45 SONY MICORMV IP-210 SONY MICORMV IP-7 SONY MICORMV IP-55 SONY MICORMV IP-220 Owners Manual 95 IEEE 1394 IEEE 1394 functions continued IEEE 1394 functions continued how to save the MicroMV Camcorder to the DVR 1. On playing the MicroMV Camcorder, press the D / E / F / G buttons to move to DVR $ and then use the ENTER button. Save the current screen to the DVR. 2. Press the D / E / F / G buttons to move to DVR # and then use the ENTER button to end a saving. 96 Plasma TV IEEE 1394 functions continued IEEE 1394 functions continued How to connect the 1394 When connecting these 3 methods, the 1394 will not work properly. IEEE 1394

(a) LOOP Connection VHow to save the DVHS to the DVR

<Connect the IEEE1394 Cable>

(b) Daisy Chain 1. On playing the DVHS, press the D / E / F / G buttons to move to " and then use the ENTER button.

<Connect the IEEE1394 Cable>

<Connect the IEEE139 4 Cable>

<DVHS>

<TV>

<TV>

<MicroMV Camcorder>

<Connect the IEEE1394 Cable>

<DVHS>

(c) MicroMV Camcorder Daisy Chain

<Connect the IEEE1394 Cable>

or

<DVHS>

<MicroMV Camcorder>

<Connect the IEEE1394 Cable>

<TV>

Owners Manual 97 98 Plasma TV Function CableCARD Function CableCARD

* In this manual, the OSD (On Screen Display) may be different from your TVs because it is just example to help Operation the TV operation. Cable menu options Cable menu options

- The Cable sub menu displays when inserting the CableCARDTM to the TV.

- The CableCARDTM type is Motorola, Scientific Atlanta (SA), or SCM etc. The OSD (On screen display) is different from your TV according to your CableCARDTM type. 1. Press the MENU button and then use D / E button to select the CABLE menu. 2. Press the G button and then use D / E button to select your desired item. 3. Press the G button. 4. Press EXIT button to return to TV viewing. In case of Scientific Atlanta CableCARD SETUP SA CableCARD Diag Screen G SA CableCARD/Host ID Screen VIDEO AUDIO TIME OPTION LOCK CABLE MENU i.e) CableCARD/ Host ID Screen CableCARD Message In order to start service for this device, please contact customer service at Ph#: 1-866-303-0422 CableCARD(tm): 0-010-405-698-001 HOST ID: 0-080-000-000-226 EXIT Exit

- As shown, the pairing number means your TV and CableCARDTM ID. For further information regarding cable TV ser-

vice, contact your local cable TV service provider(s). Scrambled channel Scrambled channel

Insert the CableCARDTM. If you do it at first, it takes about 1 minute to exchange the data between the TV and the CableCARDTM. Then, TV screen displays as shown right.

- Let your cable TV service provider know CableCARDTM ID and Host ID.

If your cable TV service provider is registered CableCARDTM ID and Host ID, you can watch the premium or high value channel. If you ever registered to the cable TV service provider, you can watch the pre-

mium or high value channel without a message.

CableCARD Message In order to start cable service for this device, please contact SuperVision Cable at 1-800-555-8888 POD ID: 7-561-034-449-009 Host ID: 0-100-331-784-018 EXIT Exit Please call your operator and report an invalid CableCARDTM.

If the certificate dont match between the TV and the CableCARDTM, the OSD (On screen display) displays as shown left. Owners Manual 99 Operation Cable Channel List Cable Channel List 1. 3. G Selection ( G or ) leads you to the channel edit screen. SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Label Set ID MENU Previous 2. 4. 1. If you enter the Channel Edit after running the EZ Scan, you can see the cable channel list. 2. Inserting the CableCARDTM. Then, the TV receive a new cable channel list. At this time, it takes about 2~3 minutes.

(Occasionally more than that time). Note:

As data gathering of CableCARDTM, it may make a noise by fan in standby mode. Emergency Alert Message Alert Message Emergency

If an emergency situation occur during watching the TV, you can receive a message from cable TV service provider(s).

- When receiving an emergency message, the message is displayed on the screen as shown below or the channel is changed automatically to a channel that maintains the emergency message. The message automatically disap-

peared. Emergency Action Notification Hurricane will be coming!!!

100 Plasma TV Operation Remote Control Remote Control PIPPIP (Picture-In-Picture) / POP

(Picture-In-Picture) / POP / T/ Twin Picture win Picture

- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image.

- Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen. If you set the block/rating for Lock menu options in PIP/Twin Picture mode, Rating Blocked doesnt display on screen.

W W WWatching PIP/POP/T atching PIP/POP/Twin Picture win Picture Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below. PIP Mode POP Mode Twin Picture Mode F D E TV 2-0 TV 4-0 TV 6-0 PIP Off W W Selecting an Input Signal Source for PIP/T Selecting an Input Signal Source for PIP/Twin Picture win Picture Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. You can also select sources for the Sub Input in the SETUP menu. Main Picture Source Available Sub Picture Sources DTV Analog Analog, Video, and Front Video DTV, Analog, Video, and Front Video W W Swapping the PIP Swapping the PIP/T/Twin Picture win Picture Repeatedly, use the SWAP button to switch the main and sub pictures. Component 1, Component 2, RGB-PC (or RGB-DTV), HDMI1/DVI,HDMI2 input sources for the main picture cant be used to swap the main and sub pictures. Main Picture Sub Picture Main Picture Sub Picture TV Program selection for PIP W W TV Program selection for PIP 1. Press the PIP button. 2. Select the Antenna or Cable option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+ /

PIPCH- button to select a channel for the sub picture.

(You cant select DTV for main and sub picture simultaneously). Owners Manual 101 Operation W W Moving the PIP Moving the PIP sub picture sub picture In PIP mode, press the D / E / F / G button to move the sub picture to a different location on the screen. W W Adjusting Main and Sub Picture Sizes for Adjusting Main and Sub Picture Sizes for TTwin Picture win Picture Use the D / E / F / G button to change main and sub picture sizes in Twin Picture mode. i.e) If screen is adjusted to the maximal size, the large screen is filled with entire screen vertically as shown. W W POPPOP (Picture-out-of-Picture: Channel Scan)

(Picture-out-of-Picture: Channel Scan)

- Use POP to search the programs of all the memorized channels one-by-one on the 3 PIP screen display,

(while the main picture source remains the current channel). The pictures of all the programmed channels are searched with the 3 POP screen.

- Notes:

Run EZ Scan channel search before using POP mode. When Sub pictures are changed from the TV/DTV to CATV/CADTV in POP mode, it may make a noise from the Tuner switch. 1. Press the PIP button to activate the POP mode while in PIP mode. Channel selection: Use F button to enlarge the selected channel being searched on the PIP screen to shift it for viewing on the Main screen. PIP selection: Use D / E button to select one of 3 PIP screen pictures in POP mode. When watching TV/CATV on Main picture, TV/CATV or DTV/CADTV on Sub pictures are in chan-

nel scanning. However, when watching DTV/CADTV on Main picture, only TV/CATV on Sub pic-

ture is in channel scanning. 2. Press the EXIT button to cancel POP mode. F D E TV 2-0 TV 4-0 TV 6-0 102 Plasma TV Operation Information Information Operation: Watching TV/DTV/CATV/CADTV Watching Video, Front Video Watching IEEE 1394 In Component1, Component2, RGB, HDMI1/DVI,HDMI2 modes, INFO button is not working. Function: Show the present screen information. On Watching with the upper Input signal, press the INFO button. Press the INFO button or EXIT button to exit. A: Banner information, Refer to the

<Channel Banner>. B: Program title C: Day, Month, Year D: Program start time E: Program finish time F: Show the prosessing rate G: Present time H: Added information. Refer to the icon explanation. I: Gemster information 4 : 3 16 : 9 Screen Ratio of Input Signal 4:3 Screen Ratio of Input Signal 16:9 480i 480p 720p 1080i Resolution of Input Signal 720x480i Resolution of Input Signal 720x480p Resolution of Input Signal 1280x720p Resolution of Input Signal 1920x1080i Multilingual : Input Signal have over two Audio infor-

mation. Press the SAP button to select wanted Audio. Caption: Input Signal have over one Close service. Press the CC button to select wanted Closed caption. CC Input Signal have rating information . Refer to the

<Lock Menu>. D (Dialogue), L (Language), S (Sex), V (Violence), FV

(Fantasy Violence) B C D F E Live Eden 1080I Sat, Dec 20, 2003 7:00PM 9:00PM H Multilingual CC Caption 16 : 9 Wide I G A TV 6-0 MONO STEREO CNBC Owners Manual 103 Operation EZ Mute EZ Mute

- Nothing to do with Caption on/Off using Mute button, the mode selected Caption/Text is to be displayed.

- When you repeatedly press the Mute button, the screen is displayed in turn. (Refer to the lower picture) Note:

EZ Mute only operates in DTV/Analog/Video/Front Video/IEEE1394. 104 Plasma TV External Control Device Setup External Control Device Setup External Control Device Setup

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitors functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.

- RS-232C connection cables are not supplied with the Monitor. RS-232C Setup RS-232C Setup RS-232C INPUT

(CONTROL/SERVICE) I E E E 1 3 9 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O PC TType of Connector; D-Sub 9-Pin Male ype of Connector; D-Sub 9-Pin Male No. Pin Name 1 2 3 4 5 6 7 8 9 No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations RS-232C Configurations 1 5 9 6 7-Wire Configurations

(Standard RS-232C cable) 3-Wire Configurations

(Not standard) PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS PDP 3 2 5 6 4 8 7 TXD RXD GND DSR DTR CTS RTS PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS PDP 3 2 5 4 6 7 8 TXD RXD GND DTR DSR RTS CTS D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 Owners Manual 105 External Control Device Setup Set ID Set ID Use this function to specify a monitor ID number. Refer to Real Data Mapping. See page 82. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select SET ID. 3. Press the G button and then use D / E button to adjust SET ID to choose the desired monitor ID number. The adjustment range of SET ID is 1 ~ 99. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Label Set ID MENU Previous G 1 1 Communication Parameters Communication Parameters Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None

* Use a crossed (reverse) cable. Stop bit : 1 bit Communication code : ASCII code TTransmission / Receiving Protocol ransmission / Receiving Protocol Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

* [Command 1]: First command to control the set. (j or k)

* [Command 2]: Second command to control the set.

* [Set ID]: You can adjust the set ID to choose desired monitor ID number in Setup menu. Adjustment range is 1

~ 99. When selecting Set ID 0, every connected the TV is controlled. Set ID is indicated as decimal

(1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.

* [DATA]: To transmit command data. Transmit FF data to read status of command.

* [Cr]: Carriage Return ASCII code 0x0D

* [ ]: ASCII code space (0x20) OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time Command Reference List Command Reference List COMMAND 1 COMMAND 2 DATA

(Hexadecimal) k 01. Power k 02. Input Select k 03. Aspect Ratio k 04. Screen Mute k 05. Volume Mute k 06. Volume Control k 07. Contrast k 08. Brightness k 09. Color k 10. Tint k 11. Sharpness k 12. OSD Select 13. Remote Control Lock Mode k k 14. PIP/Twin k 15. PIP Position k 16. Treble 17. Bass k k 18. Balance k 19. Color Temperature k 20. PIP Input Source 21. ISM Method j j 22. Low Power j 23. Orbiter Time Setting 24. Orbiter Pixel Setting j a b c d e f g h i j k l m n q r s t u y p q r s 0 ~ 1 0 ~ 9

0 ~ 1 0 ~ 2 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 1 0 ~ 1 0,1,2,5 0 ~ 3 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 2 0 ~ 3

0 ~ 1 1 ~ FE 1 ~3 DATA 2 DATA 3 DATA 4 DATA 5

(Hexadecimal)

(Hexadecimal)

(Hexadecimal)

(Hexadecimal) 01 ~ 87 00 ~ FE 00 ~ FF 00 ~ FF 00 ~ FF

(Hexadecimal) DATA 1 DATA 0 COM-

MAND 1 COM-

MAND 2

(Hexadecimal) 25. Channel Tuning m a 26. Channel Add/Del m b m c *

27. Key 28. Input Select x b *

29. PIP Input Select x y *

106 Plasma TV 01 ~ 87 00 ~ 01 External Control Device Setup 01. Power (Command2:a) G To control Power On/Off of the Monitor. Transmission

[k][a][ ][Set ID][ ][Data][Cr]

Data 0 : Power Off Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

1 : Power On 05. Volume Mute (Command2:e) G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission

[k][e][ ][Set ID][ ][Data][Cr]

Data 0 : Volume mute off (Volume on) 1 : Volume mute on (Volume off)

* In a like manner, if other functions transmit FF data based on this format, Acknowledgement data feedback presents status about each function. Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

02. Input Select (Command2:b) (Main Picture Input) G To adjust volume. 06. Volume Control (Command2:f) G To select input source for the Monitor. Transmission

[k][b][ ][Set ID][ ][Data][Cr]

Data 0: DTV 1: Analog 2: Video1 3: Video2 4: Component 1 Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

5: Component 2 6: RGB-DTV 7: RGB-PC 8: HDMI1/DVI 9: HDMI2 03. Aspect Ratio (Command2:c) (Main picture format) G To adjust the screen format. You can also adjust the screen format using the RATIO button on remote control or in the Option menu. Transmission

[k][c][ ][Set ID][ ][Data][Cr]

Date 1: 4:3 2: 16:9 3: Horizon 4: Zoom 1 5: Zoom 2 Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

6: Set by program 10: Cinema Zoom (1) 1F: Cinema Zoom (16) 04. Screen Mute (Command2:d) G To select screen mute on/off. Transmission

[k][d][ ][Set ID][ ][Data][Cr]

Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

You can also adjust volume with the volume buttons on remote control. Transmission

[k][f][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64 Refer to Real data mapping as shown below. Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g) G To adjust screen contrast. You can also adjust contrast in the Video menu. Transmission

[k][g][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64 Refer to Real data mapping as shown below. Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

08. Brightness (Command2:h) G To adjust screen brightness. You can also adjust brightness in the Video menu. Transmission

[k][h][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64 Refer to Real data mapping as shown below. Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

* Real data mapping 0 : Step 0 A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 63 : Step 99 (SET ID 99) 64 : Step 100 Owners Manual 107 External Control Device Setup 09. Color (Command2:i) G To adjust the screen color. You can also adjust color in the Video menu. Transmission

[k][i][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64 Refer to Real data mapping. See page 82. Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j) G To adjust the screen tint. You can also adjust tint in the Video menu. Transmission

[k][j][ ][Set ID][ ][Data][Cr]

Data Red : 0 ~ Green : 64 Refer to Real data mapping. See page 82. Acknowledgement

[ j ][ ][Set ID][ ][OK][Data][x]

11. Sharpness (Command2:k) G To adjust the screen sharpness. You can also adjust sharpness in the Video menu. Transmission

[k][k][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64 Refer to Real data mapping. See page 82. Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l) G To select OSD (On Screen Display) on/off. Transmission

[k][l][ ][Set ID][ ][Data][Cr]

Data 0: OSD off 1: OSD on Acknowledgement

[l][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m) G To lock the remote control and the front panel controls on the set. Transmission

[k][m][ ][Set ID][ ][Data][Cr]

Data 0: Lock off Acknowledgement

[m][ ][Set ID][ ][OK][Data][x]

1: Lock on 108 Plasma TV 14. PIP / POP / Twin Picture (Command2:n) G To control the PIP (Picture-in-Picture)/POP/Twin picture. You can also control the PIP/POP/Twin picture using the PIP button on the remote control. Transmission

[k][n][ ][Set ID][ ][Data][Cr]

Data 0: PIP off 1: PIP Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

2: POP 3: Twin Picture 15. PIP Position (Command2:q) G To select sub picture position for PIP. Transmission

[k][q][ ][Set ID][ ][Data][Cr]

Data 0: Right down on screen 1: Left down on screen 2: Left up on screen 3: Right up on screen Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

16. Treble (Command2:r) G To adjust treble. You can also adjust treble in the Audio menu. Transmission

[k][r][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64 Refer to Real data mapping. See page 82. Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

17. Bass (Command2:s) G To adjust bass. You can also adjust bass in the Audio menu. Transmission

[k][s][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64 Refer to Real data mapping. See page 82. Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

18. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Audio menu. Transmission

[k][t][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64 Refer to Real data mapping. See page 82. Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

19. Color Temperature (Command2:u) G To adjust color temperature. You can also adjust color temperature in the Video menu. Transmission

[k][u][ ][Set ID][ ][Data][Cr]

Data 0: Cool 1: Medium 2: Warm Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

20. PIP Input Select (Command2:y) G To select input source for sub picture in PIP/Twin pic-

ture mode. Transmission

[k][y][ ][Set ID][ ][Data][Cr]

Data 0: DTV 1: Analog 2: Video1 3: Video2 Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

21. ISM Method (Command2:p) G To avoid having a fixed image remain on screen. Transmission

[ j ][p][ ][Set ID][ ][Data][Cr]

Data 1: Inversion 2: Orbiter 4: White Wash 8: Normal Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

22. Low Power (Command2:q) G To control the low power function on/off. Transmission

[ j ][q][ ][Set ID][ ][Data][Cr]

Data 0: low power off 1: low power on Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

23. Orbiter Time Setting (Command2:r) G To adjust orbiter operation time term. Transmission

[ j ][r][ ][Set ID][ ][Data][Cr]

Data Min: 1 ~ Max: FE Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

External Control Device Setup 24. Orbiter Pixel Setting (Command2:s) G To adjust pixel number in orbiter function. Transmission

[ j ][s][ ][Set ID][ ][Data][Cr]

Data Min: 1 ~ Max: 3 Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

25. Tune Command (Command: m a) G To tune channel to following physical/major/minor number Transmission

[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr]

Data 0: Physical channel number Min: 1~ Max: 0x87 Data 1, Data 2: Major Channel Number (two part)/ Channel Number (One part) (Data 1: High, Data 2: Low) Data 3, Data 4: Minor Channel Number (Data3: High, Data4: Low) Data 5:

Main/Sub Picture Main Sub 6 0 1 7 0 1 Two/One Part Channel Two One Using Physical Channel Use No Use 5 0 1 Reserv 4 ed x x x x x x x x x x 3 2 1 0 Step 0 0 0 0 0 0 0 0 x 1 0 0 0 0 1 1 1 1 x 1 0 0 1 1 0 0 1 1 x 1 0 1 0 1 0 1 0 1 x 1 NTSC Air NTSC Cable ATSC Air ATSC Cable_std ATSC Cable_hrc ATSC Cable_irc ATSC cable_auto Reserved

... Reserved

* All data are transmitted by Hexadecimal code

*Two/One part Channel: 6th bit This bit is used in a cable-ready system.

*Using physical channel: 5th bit If the channel band is NTSC air or NTSC cable, channel tun-

ing can be done by only physical channel. In this case, using physical channel bit must be low(0). But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1). Example) 1. Analog channel: NTSC cable, channel number(35), main picture Command: ma 00 23 xx xx xx xx 01 attribute(0x01):

main picture, two part(its not mandatory), using physical chan-

nel, NTSC cable xx data: dont care major and minor channel number in case analog channel tuning. 2. Digital channel: ATSC air, channel number(dont know phys-

ical channel, major(30), minor(3)), sub picture Command: ma 00 xx 00 1E 00 03 A2 attribute(0xA2): sub pic-

ture, two part, not using physical channel, ATSC air xx data:

dont care analog channel number in case digital channel tun-

ing. 3. Digital channel: ATSC air, channel number(physical(20),major(20), minor(3)), sub picture Command: ma 00 14 00 14 00 03 82 attribute(0x82): sub pic-

ture, two part, using physical channel, ATSC air. Acknowledgement

[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][x]

[a][ ][Set ID][ ][NG][Data0][x]

Owners Manual 109 26. Channel Add/Del (Command: m b) G To add and delete the channels Transmission 29. PIP Input Select(Command: x y) G To adjust input source for sub picture in PIP mode Transmission

[x][y][][Set ID][][Data][Cr]

Data Structure MSB LSB 0 0 0 0 0 0 0 0 External Input Input Number External Input Data Input Number Data 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 DTV Analog AV Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Acknowledgement

[y][][Set ID][][OK/NG][Data][x]

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Input1 Input2 Input3 Input4 Input5 Input6 Input7 Input8 Input9 Input10 Input11 Input12 Input13 Input14 Input15 Input16 Note:

In case Video/S-Video is selected automatically by TV, use only single Video input. In case Video/S-Video is selected by user manually, use sepa-

rate Video/S-Video inputs.

[m][b][ ][Set ID][ ][Data][Cr]

Data 0: Channel Delete 1: Channel Add Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

[b][ ][Set ID][ ][NG][Data][x]

27. Key (Command: m c) G To send IR remote key code Transmission

[m][c][ ][Set ID][ ][Data][ ][Cr]

Data Key code: Refer to page 86. Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

28. Input select(Command: x b) (Main Picture Input) G To select input source for TV. Transmission

[x][b][][Set ID][][Data][Cr]

Data Structure MSB LSB 0 0 0 0 0 0 0 0 External Input Input Number External Input Data Input Number Data 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Input1 Input2 Input3 Input4 Input5 Input6 Input7 Input8 Input9 Input10 Input11 Input12 Input13 Input14 Input15 Input16 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 1 0 1 0 1 DTV Analog AV Reserved Component RGB_DTV RGB_PC Reserved Reserved HDMI1 Reserved Reserved Reserved Reserved Reserved Acknowledgement

[b][][Set ID][][OK/NG][Data][x]

110 Plasma TV IR Codes IR Codes IR Codes How to Connect How to Connect G Connect your wired remote control to the Remote Control port on the TV. Remote Control IR Codes Remote Control IR Codes G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC T1 Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 G Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame G Lead code Repeat code Tf 9 ms 4.5 ms G Repeat code 0.55 ms G Bit description Bit 0 9 ms 0.56 ms 1.12 ms 2.25 ms Bit 1 G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 0.56 ms 2.24 ms Owners Manual 111 IR Codes Code (Hexa) Function Note 0B 08 C4 C5 79 0E 10 ~ 19 4C 1A 09 02 03 00 01 1E AA 39 40 41 07 06 44 43 52 4D 5B 60 72 71 61 63 65 0A CB D6 5A D0 BF D4 D5 D7 C6 CC 76 77 AF 70 87 B0 BA B1 BD 8F 8E B2 B3 A9 92 C4 80 C8 7D TV/VIDEO POWER POWER ON POWER OFF RATIO TIMER Number Key 0~ 9

- (Dash) FLASHBK MUTE VOL D VOLE CH D CH E FAV INFO CC D E F G ENTER MENU EZ SOUND EZ PIC EXIT PIP PIPCH -

PIPCH +

PIP INPUT SWAP FREEZE SAP ADJUST TV VIDEO Front Video COMPONENT 1 COMPONENT 2 RGB-PC RGB-DTV HDMI1/DVI HDMI2 Ratio 4:3 Ratio 16:9 Ratio Zoom POP 1394 PLAY PAUSE STOP REC REW FF GOTOPREV GOTONEXT TV GUIDE APM MC EJECT AUTO DEMO X STUDIO MARK R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (Video Input Selection) Discrete IR Code (Front Video Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (RGB-DTV Input Selection) Discrete IR Code (HDMI1/DVI Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) Discrete IR Code (Channel Search) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button 112 Plasma TV Programming Codes Programming the Remote Programming the Remote G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands. Programming a code into a remote mode Programming a code into a remote mode 1. Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding the desired component button on the remote control, while illuminating at the selected component. Test the POWER and CH D/E buttons to see if the component responds properly. If not, the remote requires programming to oper-

ate the device. 2. Turn on the component to be programmed, then press the corresponding the desired component button on the remote control. 3. Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code. 4. There are two ways to find the right code for the component. A. If you press the CH D/E buttons repeatedly, the codes will change one at-a-time. Press the POWER button after each code change. If the right code is found, the device will turn off. B. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device will turn off. 5. Press the MENU button to store the code. 6. Test the remote control functions to see if the component responds properly. If not, repeat from step 2. Owners Manual 113 Programming the Remote Brand TATUNG TEAC TECHNICS TEKNIKA THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH Codes 039 043 034 039 043 031 033 070 019 031 033 034 101 034 006 008 013 042 047 059 082 112 131 040 101 040 012 048 012 034 046 040 003 013 017 024 031 033 034 040 053 054 131 012 034 039 043 034 048 056 058 072 080 101 Brand SL MARX SPRUCER STARCOM STARGATE SYLVANIA TADIRAN TAEKWANG TAIHAN TANDY TEXSCAN TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL VIEWSTAR ZENITH Codes 030 047 078 002 004 008 009 008 030 067 030 110 105 017 029 067 039 040 056 100 007 014 024 004 053 005 007 014 024 026 027 032 035 012 015 018 086 087 088 089 100 114 060 093 Programming Codes Programming Codes VCRs VCRs Brand AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO Codes 034 016 043 046 124 125 146 072 031 033 103 012 023 039 043 035 037 129 028 031 033 108 003 040 135 031 033 041 005 007 010 064 065 108 110 111 112 116 117 119 108 012 023 039 043 034 053 059 006 017 025 027 029 031 034 035 036 037 046 101 129 131 138 153 003 008 009 010 034 031 033 063 072 107 109 144 147 GO VIDEO 132 136 HARMAN KARDON 012 045 HITACHI DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE 004 018 026 034 043 063 137 150 031 033 031 033 012 013 015 033 040 066 101 043 012 031 033 043 048 050 055 060 130 150 152 Brand KENWOOD LG (GOLDSTAR) LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI MTC MULTITECH NEC NORDMENDE OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER Codes 014 034 039 043 047 048 001 012 013 020 101 106 114 123 034 003 009 013 014 017 034 101 106 040 031 033 034 041 067 068 012 031 033 067 069 101 027 030 031 033 003 010 014 031 033 034 053 072 101 102 134 139 045 046 059 013 020 013 020 045 046 049 051 059 061 151 034 040 024 034 012 023 039 043 048 043 053 054 066 070 074 083 133 140 145 013 020 031 033 063 031 034 067 031 033 034 054 067 071 101 101 013 021 048 Brand PORTLAND PULSAR QUARTZ QUASAR RCA REALISTIC RICO RUNCO SALORA SAMSUNG SANSUI SANYO SCOTT SEARS 010 SHARP SHINTOM SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY Codes 108 072 011 014 033 066 075 145 013 020 033 034 040 041 062 063 107 109 140 144 145 147 003 008 010 014 031 033 034 040 053 054 101 058 148 014 032 040 102 104 105 107 109 112 113 115 120 122 125 022 043 048 135 003 007 010 014 102 134 017 037 112 129 131 003 00 013 014 017 020 031 042 073 081 101 031 054 149 024 003 009 031 052 056 057 058 076 077 078 149 034 013 031 033 034 059 067 034 010 034 009 Codes 003 004 039 042 046 052 053 112 014 005 007 014 024 026 092 007 007 065 090 080 081 019 030 023 020 030 040 057 062 066 032 072 008 022 025 054 052 074 Brand GOLDEN CHANNEL HAMLIN HITACHI HOSPITALITY JERROLD LG (GOLDSTAR) M-NET MACOM MAGNAVOX MEMOREX MOVIE TIME NSC OAK PANASONIC PARAGON PHILIPS Codes 030 049 050 055 052 055 070 077 002 003 004 008 009 010 052 069 074 001 106 101 005 037 033 010 012 064 079 100 028 032 015 028 038 071 073 016 031 037 053 044 047 100 006 012 013 020 Brand PIONEER Codes 065 085 090 034 051 052 063 076 POST NEWS WEEK 016 059 PRUCER 011 048 071 072 PTS 073 074 100 047 049 050 057 025 091 102 107 030 068 003 011 041 042 043 045 046 022 030 052 PULSAR RCA REGAL REGENCY REMBRANT RK SAMSUNG SCIENTIFIC ATLANTA SHERITECH SIGNAL SIGNATURE INSTANTREPLAY JCL JCPENNY JENSEN JVC CACATVTV Brand ABC AJIN ANTRONIK ARCHER CABLE STAR CENTURION CENTURY CITIZEN COLOUR VOICE COMBANO COMTRONICS DIAMOND EAGLE EASTERN ELECTRICORD GE GEMINI GI 114 Plasma TV Programming Codes HDSTB HDSTB Brand Codes ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER 013 014 015 018 123 050 051 126 129 053 053 CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME 036 055 008 009 012 077 054 050 145 005 006 007 010 011 052 112 116 141 024 046 056 076 038 040 057 058 093 094 095 096 097 098 099 100 122 089 Codes Brand Codes Brand Codes Brand EUROPLUS FUJITSU 114 017 021 022 027 133 134 GENERAL INSTRUMENT 003 004 016 029 HITACHI HOUSTON TRACKER HUGHES HYTEK JANIEL JERROLD KATHREIN LEGEND LG LUTRON LUXOR MACOM 031 059 101 139 140 033 037 039 051 057 104 068 053 060 147 061 108 057 001 132 062 144 010 059 063 064 065 057 028 124 125 069 070 MEMOREX NEXTWAVE NORSAT PACE SKY SATELLITE 143 060 142 PANASONIC PANSAT 121 PERSONAL CABLE 117 071 PHILIPS 105 PICO PRESIDENT 019 102 030 110 111 PRIMESTAR 072 PROSAT 066 106 RCA 043 074 REALISTIC SAMSUNG 123 SATELLITE SERVICE CO 028 035 047 057 SCIENTIFIC ATLANTA SONY 085 032 138 103 STARCAST SUPER GUIDE TEECOM TOSHIBA UNIDEN UNIDEN VIEWSTAR WINEGARD ZENITH 041 020 124 125 023 026 075 087 088 090 107 130 137 002 127 016 025 042 043 044 045 048 049 078 079 080 086 101 135 136 115 128 146 081 082 083 084 091 120 Audio Audio Brand AIWA AKAI ANAM BURMECTER CARVER CLARION DAEWOO DENON FANTASIA FINEARTS FISHER LG(GOLDSTAR) HAITAI HARMAN/KARDON 068 INKEL Codes 014 028 070 096 125 129 139 229 230 163 003 014 017 023 059 106 189 216 217 235 236 252 086 199 027 053 060 084 102 148 198 221 015 075 130 143 071 022 089 099 001 021 024 029 087 107 108 110 190 191 192 210 211 212 239 034 035 188 222 037 058 062 069 078 079 095 121 122 149 150 151 152 153 154 155 157 158 159 160 189 207 222 224 225 226 227 243 247 Brand JVC KEC KENWOOD KOHEL NAD LOTTE LXI MAGNAVOX MARANTZ MCINTOSH MCS MEMOREX NAD ONKYO OPTIMUS PANASONIC PENNEY Codes 004 013 141 185 186 187 038 050 067 089 170 171 197 206 215 222 030 045 046 014 016 036 098 100 172 173 174 175 176 177 178 179 180 181 183 201 202 208 213 214 219 223 232 238 240 103 111 002 018 020 025 034 041 081 090 097 112 049 104 107 046 013 040 041 047 048 056 057 132 133 140 158 007 033 064 113 142 220 241 251 104 Brand PHILIPS PIONEER QUASAR RCA RCX REALISTIC SAMSUNG SANSUI SANYO SCOTT SHARP SHERWOOD SONY TAEKWANG TEAC TECHNICS Codes Brand Codes TOSHIBA THE VICTOR WARDS YAMAHA 147 218 137 061 088 131 089 054 055 066 092 199 026 112 143 253 039 042 043 063 065 091 093 094 115 123 127 250 113 080 092 103 106 124 145 146 182 193 194 195 203 204 244 245 246 011 135 138 144 019 083 234 106 186 031 032 051 052 072 082 117 119 156 184 199 200 206 209 005 006 158 044 045 109 114 118 126 248 249 012 020 073 074 076 077 105 161 162 163 164 165 166 167 168 169 205 231 233 242 254 010 085 106 136 185 187 237 101 113 128 134 DVDDVD Brand Codes 022 020 014 005 006 APEX DIGITAL DENON GE HARMAN KARDON 027 012 JVC LG 001 010 016 025 Brand MAGNAVOX MARANTZ MITSUBISHI NAD ONKYO PANASONIC Codes 013 024 002 023 008 017 003 009 Brand PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG Codes 013 004 026 021 005 006 005 006 011 015 Brand SONY THOMPSON TOSHIBA YAMAHA ZENITH Codes 007 005 006 019 008 009 018 010 016 025 Owners Manual 115 TTroubleshooting Checklist roubleshooting Checklist Troubleshooting Checklist Check whether the TV is turned on. Is the power cord inserted into wall power outlet?

No picture &

No sound Test the wall power outlet, plug another products power cord into the outlet where the TVs power cord was plugged in. Picture OK &

No sound Press the VOLUME (G) button. Sound muted? Press MUTE button. Check to see if there is any object between the TV and the remote control causing obstruction. The remote control doesnt work Are batteries installed with correct polarity (+ to +, - to -)?

(Refer to p.10) Correct remote operating mode set: TV, VCR etc.?

Install new batteries. (Refer to p.10) Picture appears slowly after switching on This is normal, the image is muted during the TV startup process. Please contact your service center, if the picture has not appeared after five minutes. Select Color in the Video menu and press the VOLUME (G) button.

(Refer to p.61) No or poor color or poor picture Keep a sufficient distance between the TV and the VCR. Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.) Horizontal/vertical bars or picture shaking Check for local interference such as an electrical appliance or power tool. No output from one of the speakers Adjust Balance in the AUDIO menu. (Refer to p.63) Unusual sound from inside the TV A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the TV. 116 Plasma TV Maintenance Maintenance Maintenance

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Cleaning the Screen 1. Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence Absence Extended If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Owners Manual 117 Product Specifications Product Specifications Specification MODELS TU-50PY22/TU-50PY2DR-UA TU-60PY22/TU-60PY2DR-UA Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Resolution Power requirement Television System Program Coverage External Antenna Impedance Color Operating Temperature Range Operating Humidity Range Maximum Elevation 55.2 / 1402 31.4 / 798.5 11.9 / 302.5 122 / 55.3 67.24 / 1708 36.6 / 931 12.6 / 320.7 189.2 / 85.8 1366 x 768 (Dot) AC100-240V ~ 60Hz NTSC-M, ATSC VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135. DTV 2 ~ 69 75 16,770,000 (256 steps of each R, G and B) 32 ~ 104F (0 ~ 40C) Less than 80%

6561 feet (2000m) The specifications shown above may be changed without prior notice for quality improvement. 118 Plasma TV LG ELECTRONICS, INC. PLASMA TV U.S. LIMITED WARRANTY Your LG Plasma TV will be repaired or replaced in accordance with the terms of this warranty, at LGEs option, if it proves to be defective in material or workmanship under normal use, during the warranty period (Warranty Period) listed below, effective from the date (Date of Purchase) of original consumer purchase of the product. This war-

ranty is good only to the original purchaser of the product and effective only when used in the United States, includ-

ing Alaska, Hawaii, and U.S. Territories. WARRANTY PERIOD:

HOW SERVICE IS HANDLED:

LABOR and PARTS: 2 YEARS from the Date of Purchase. Your unit will be repaired or replaced with a new, substitute model or factory reconditioned unit, at LGEs option. If repaired, parts used in the repair may be new or remanufac-

tured. Replacement Units and Repair Parts are warranted for the remaining portion of the original units warranty period. EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user. KEEP THE DEALERS DATED BILL OF SALE OR PROOF OF DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service. In-Home Service: Please retain dealers dated bill of sale or delivery ticket as evidence of the Date of Purchase for proof of warranty, and submit a copy of the bill of sale to the ser-

vice person at the time warranty service is pro-

vided. Please call 1-201-816-2000 to locate your nearest LGE Authorized Service Center. Visit our website at:

http://www.lgservice.com THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state. CONCERNING PIXEL FUNCTIONALITY: Your Plasma TV contains about one million individual pixels. Plasma TV typically contain a small number of pixels that do not function normally. Your display has been inspected and is in compliance with manufacturers specifications, indicating that any pixel defects do not effect the operation or use of your display. IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your product online. This information will allow us to reach you promptly should we discover a safety or reliability prob-

lem that could affect you. THIS LIMITED WARRANTY DOES NOT APPLY TO:

G damage caused in shipping or transit G service required as a result of improper installation, including incorrect or insufficient AC supply (please consult the owners manual for power supply requirements) G installation or repair of antenna systems, cable con-

verters, cable company supplied equipment, or other components in a video system gence, improper maintenance or storage, or to acts of nature or other causes beyond our control.

(Causes beyond our control include but are not lim-

ited to lightning strike, power surges, power out-

ages and water damage.) G image burn-in G repair or replacement of warranted parts by other than LGE authorized service centers. G set-up or adjustment on consumer controls, or G units purchased or serviced outside of the coverage damage caused by improper adjustments area. G damage caused by other system components G any panel that has been modified or incorporated into any other product G replacement of batteries on the remote control. G damage (including cosmetic damage), failure, loss or personal injury due to misuse, abuse, negli-

G product where the original factory serial numbers have been removed, defaced or changed in any way. G product sold and labeled as as is, where is or sim-

ilar disclaimer. The cost of repair or replacement under these excluded circumstances shall be borne by the consumer. CUSTOMER INTERACTIVE CENTER NUMBERS:

To obtain customer assistance, product information or Dealer or Service locations Call 1-201-816-2000 24 hours a day, 365 days per year FOR SERVICE:

Before you call for warranty service, check your operating guide you may avoid a service call. For warranty service information, please contact the LGE Customer Interactive Center telephone number. When calling for service, please have your product model number, serial number and the date of pur-

chase or the date of original installation available. If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not be charged if you return the defective unit within 10 working days. If a replacement unit is received, please use the carton and packaging from that unit in returning the defective unit to the LGBrand Service Center. Parts and service in accordance with the LGE warranty are LGEs responsibility and will be provided without charge. Other service requirements will be at the owners expense. If you have problems in obtaining satisfactory warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently owned and operated service organizations. To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before returning any product to the LGE Service Center. Contact the Customer Interactive Center for details. TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL:

LGE Customer Interactive Center P.O. Box 240007 201 James Record Road Huntsville, Alabama 35824 http://www.lgservice.com P/NO : 3828VA0528A