User manual PRODUCT NAME : Wi-Fi / BLE + MCU Module MODEL NAME
: LCWB-002EA H/W version : V1.0 S/W version : V1.0 The information contained herein is the exclusive property of LG and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG. REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
2 / 10 Table of Contents No Description 1 2 3 4 5 6 7 Features Block Diagram Absolute Maximum Ratings Operating Test Conditions Electrical Characteristics Pin Description Outline Drawing
[Restricted]
Page 3 3 4 4 5 9 10 LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
3 / 10 1. Features LCWB-002EA is the module for IEEE 802.11b/g/n wireless LAN + BLE5.0 + MCU. LCWB-002EA is based on Realtek RTL8720CM solution. IEEE 802.11 b/g/n HT20 single band WLAN infra-structure Bluetooth Low Energy 5.0 (BLE5.0) Size : 20 mm x 45 mm x 9.35 mm Auto-calibration (RF, Crystal) Data rates up to 72.2Mbps PHY rate SPI interface Integrated IPv4/IPv6 TCP/IP stack Integrated Network services such as HTTP, DNS, FTP Security : WFA, WPA, WPA2, WEP, WAPI, TKIP Application : Home Appliance 2. Block Diagram ANT 802.11 b/g/n BLE5.0 MAC/BB RTL8720CM MCU
(Real M300) ROM 384KB RAM 256KB pSRAM 4MB Interface Block PMU SPI JTAG Flash Memory
(8MB) 1.8V 3.3V Clock (40MHz) LDO 3.3V DC-DC converter 5V / 12V LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
4 / 10 3. Absolute Maximum Ratings Parameter Storage Temperature Storage Humidity (@ 40) Min
-40
Max
+100 90 Unit
Caution : The specifications above the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained Also, avoid exposure to moisture 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%
3) Assemble the modules within 6 months Check the soldering ability in case of 6 months over 4. Operating Test Conditions Parameter Min Typ Max Unit Operating Temperature Operating Humidity (40) Supply Voltage 0
4.5 10.8
5.0 12
+85 85 5.5 13.2
Vdc 1) Test condition : AP connection Ping test mode(not continuous Tx and T-Put mode) LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
5 / 10 5. Electrical Characteristics 5-1. RF Characteristics for IEEE802.11b (11Mbps mode unless otherwise specified) Items Specification Mode Channel frequency Data rate Contents IEEE802.11b DSSS / CCK 2400 ~ 2483MHz 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Power Level Spectrum Mask 1st side lobes ( to fc 11MHz) 2nd side lobes ( to fc 22MHz) Modulation Accuracy (EVM) Power On/Off ramp Freq. Tolerance Chip Clock Freq. Tolerance 11 14 17 dBm
-25
-25
-30
-50 35 2.0 25 25 dBr dBr
usec ppm ppm RX Characteristics Min. Typ. Max. Unit Minimum Input Level Sens. (FER 8%) Maximum Input Level (FER 8%)
-10
-76 dBm
dBm
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards LG Innotek Confidential : This document is protected by security policies and laws. REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
6 / 10
[Restricted]
5-2. RF Characteristics for IEEE802.11g (54Mbps mode unless otherwise specified) Items Specification Mode Contents IEEE802.11g OFDM Channel frequency 2400 ~ 2483MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Power Level Spectrum Mask at fc 11MHz at fc 20MHz at fc 30MHz Constellation Error (EVM) Freq. Tolerance Chip Clock Freq. Tolerance 11 14 17 dBm
-20
-20
-20
-28
-40
-25 20 20 dBr dBr dBr dB ppm ppm RX Characteristics Min. Typ. Max. Unit Minimum Input Level Sens. (PER 10%)
Maximum Input Level (PER 10%)
-20
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards
-65 dBm
dBm LG Innotek Confidential : This document is protected by security policies and laws. REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
7 / 10
[Restricted]
5-3. RF Characteristics for IEEE802.11gn (MCS7 mode unless otherwise specified) Items Contents Specification Mode IEEE802.11n 2.4GHz OFDM Channel frequency 2400 ~ 2483MHz Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps TX Characteristics Min. Typ. Max. Unit Power Level (HT20 : MCS7) 11 14 17 dBm Spectrum Mask (HT20) at fc 11MHz at fc 20MHz at fc 30MHz Constellation Error (EVM) Freq. Tolerance Chip Clock Freq. Tolerance
-20
-20
-20
-28
-40
-28 20 20 dBr dBr dBr dB ppm ppm RX Characteristics Min. Typ. Max. Unit Minimum Input Level Sens.
(HT20,PER 10%) Maximum Input Level (PER 10%)
-20
-64 dBm
dBm
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards LG Innotek Confidential : This document is protected by security policies and laws. REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
8 / 10
[Restricted]
5-4. RF Characteristics for BLE TX characteristics Min. Typ. Max. Unit Power level 1.5 4.5 7.5 dBm Adjacent channel transmit power
@ F = F0 1MHz
@ F = F0 2MHz
@ F = F0 3MHz
@ F > F0 3MHz
Modulation characteristics Frequency derivation F1AVG F2MAX F2MAX / F1AVG 225 180 80
0 dBr
-30 dBr
-40 dBr
-40 dBr 275 KHz
KHz
RX characteristics Min. Typ. Max. Unit Min. input level (BER 0.1%) Max. input level (BER 0.1%)
-20
-84 dBm
dBm
* Normal Condition : 25, VDD=5V.
* RF characteristics is board limit. It can differ according to standards LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
9 / 10 6. Pin Description NO Board to wire Board to board 1 2 3 4 5 6 7 8 9 10 VDD MODE SPI_SCL SPI_CSN SPI_MISO SPI_MOSI STATUS GND
VDD MODE CS_N MOSI GND VDD GND SCLK MISO STATUS Top - Board to wire Bottom - Board to board Pin #1 Pin #8 Pin #1 Pin #5 Pin #6 Pin#10 LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023. 03. 29 USER MANUAL REV. NO : v1.0 REV. DATE : 2023. 03. 29 MODEL NAME : LCWB-002EA PAGE :
10 / 10 7. Outline Drawing LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023.04.03 USER MANUAL REV. NO : v1.0 REV. DATE : 2023.04.03 MODEL NAME : LCWB-002EA PAGE :
11 / 10 Regulatory Notice Part 15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Part 15.105 Statement (Class B) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Part 15.21 Statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Responsible Party Information (Supplier's Declaration of Conformity) LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs New Jersey, United States, 07632 LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023.04.03 USER MANUAL REV. NO : v1.0 REV. DATE : 2023.04.03 MODEL NAME : LCWB-002EA PAGE :
12 / 10 Regulatory Notice Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual List of applicable FCC rules This module has been granted modular approval as below listed FCC rule parts. -
FCC Rule parts 15C(15.247) Summarize the specific operational use conditions The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed in this instruction manual. RF exposure considerations The module has been certified for integration into products only by OEM integrators under the following condition:
-The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
-The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
-Mobile use As long as the three conditions above are met, further transmitter testing will not be required.OEM integrators should provide the minimum separation distance to end users in their end-product manuals. LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
REG. DATE : 2023.04.03 USER MANUAL REV. NO : v1.0 REV. DATE : 2023.04.03 MODEL NAME : LCWB-002EA PAGE :
13 / 10 Regulatory Notice Antennas list This module is certified with the following PCB antenna.
-Type: PCB Antenna
-Max. peak Antenna gain: 4.2 dBi Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.
* The antenna connector is permanently soldered prior to shipping to comply with FCC Rule 15.203 requirements Label and compliance information End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: Label and compliance information Contains FCC ID: BEJ-LCWB002EA Contains IC: 2703N-LCWB002EA Information on test modes and additional testing requirements OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.). Additional testing, Part 15 Subpart B disclaimer The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device. Note EMI Considerations Note that a host manufacture is recommended to use D04 Module Integration Guide recommending as "best practice" RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties For standalone mode, reference the guidance in D04 Module Integration Guide and for simultaneous mode; see D02 Module Q&A Question 12, which permits the host manufacturer to confirm compliance. How to make changes Since only Grantees are permitted to make permissive changes, when the module will be used differently than granted, please contact the module manufacture. LG Innotek Confidential : This document is protected by security policies and laws. Le module est tiquet avec son propre numro de certification IC. Si le numro de certification IC n'est pas visible lorsque
[Restricted]
n IC. Si le numro de certification IC n'est pas visible lorsque REG. DATE : 2023.04.03 USER MANUAL REV. NO : v1.0 REV. DATE : 2023.04.03 MODEL NAME : LCWB-002EA PAGE :
14 / 10 Regulatory Notice (ISED) RSS-GEN, Sec. 7.1.3(licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. l'exposition aux RFLantenne (ou les antennes) doit tre installe de faon maintenir tout instant une distance minimum de au moins 20 cm entre la source de radiation (lantenne) et toute personne physique. tiquetage du produit final (IC) Le module LCWB-002EA est tiquet avec sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsque le module est install lintrieur dun autre dispositif, la partie externe du dispositif dans lequel le module est install devra galement prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final devra tre tiquet sur une zone visible avec les informations suivantes :
Contient module metteur identification FCC ID: BEJ-LCWB002EA Contient module metteur IC : 2703N-LCWB002EA LG Innotek Confidential : This document is protected by security policies and laws.