FCC ID: BEJ-TM04ANNABM0 Telematics Module

Manual

(TM04ANNABM0) BEJ-TM04ANNABM0 [FCC ID]

2703H-TM04ANNABM0 [ISED ID]

1/9 1. Product Introduction The TM04ANNABM0 are designed for the automotive industry. They support LTE and WCDMA air Interface standards. The TM04ANNABM0 are based on the Qualcomm MDM9250 wireless chipsets and support the following bands. Table 1. Supported Band Region NA LTE B1/B2/B3/B4/B5/B7/B10/B12/B13/B17

/B20/B25/B26/B29/B30/B41/B66/B71 Band WCDMA B1/B2/B3/B4/B5 GSM GSM850, GSM1900 LTE B29, B30 : Rx only 1.1 Block Diagram Confidential Figure 1.1. TM04ANNABM0 Block diagram 2/9 1.2 Environmental Specifications The environmental specification for operating and storage of the TM04ANNABM0 are defined in the the table below. Table 2. Environmental Specifications Parameter Temperature Range Operating Temperature Storage Temperature Humidity

-40 to 90 (ecall 95)

-40 to +95 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TM04ANNABM0 embedded modules. 1.3.1 Absolute Maximum Rating and ESD Ratings This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TM04ANNABM0 embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter VDD VIN ESD Ratings Power Supply Input Voltage on any digital input or output pin Min

Max 6 VDD+0.5 Units V V 1 ESD1) Primary, Diversity antenna pads - Contact 1) The ESD Simulator configured with 330pF, 2000. Caution: The TM04ANNABM0 embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TM04ANNABM0 devices. 1.3.2 Current Consumption Table 4. TM04ANNABM0 Current Consumption (@12.5V TBD) kV Mode Parameter Typical Max Units LTE Max TX Output /Full RB WCDMA Max TX Output /Full RB LTE Idle, Registered WCDMA Idle, Registered 450 450 2 2 550 550

mA mA mA mA 3/9 1.4 Mechanical Specifications 1.4.1 Physical Dimensions and Connection Interface The TM04ANNABM0 embedded modules are a Land Grid Array (LGA) form factor device. The device does not have a System or RF connectors. All electrical and mechanical connections are made via the 387 pad TM04ANNABM0 on the underside of the PCB. Table5. TM04ANNABM0 Embedded Module Dimensions Nominal 39 x 43 Parameter Overall Dimension Overall Module Height 3.65 1.0 PCB Thickness Flatness Specification Weight TBD 1.4.2 Mechanical Drawing Max 39.35 x 43.35 3.85 1.1 0.1 Units mm mm mm mm g 1.4.2.1 NAD PCB

[TOP View_Without shield Can cover] [TOP View_With shield Can cover]

3.65mm

[SIDE View_With shield Can cover]

4/9 2. RF Specification The specifications for the LTE and WCDMA interfaces are defined. TM04ANNABM0 is designed to be compliant with the standard shown in the table below. Table6. Standards Compliance Technology Standards LTE WCDMA GSM 3GPP Release 11 3GPP Release 9 3GPP Release 8 2.1 LTE Specification 2.1.1 LTE RX Sensitivity The Receiver Sensitivity of the TM04ANNABM0 are specified in the following table. Table7. Conducted RX (Receive) Sensitivity LTE Bands BAND Method (DL CH) Measure BLER of Mid Channel (300) in Band1 Measure BLER of Mid Channel (900) in Band2 Measure BLER of Mid Channel (1250) in Band3 Measure BLER of Mid Channel (2175) in Band4 Measure BLER of Mid Channel (2525) in Band5 Measure BLER of Mid Channel (3100) in Band7 Measure BLER of Mid Channel (4450) in Band10 Specification sensitivity : -96.3 BLER : 5%

sensitivity : -94.3 BLER : 5%

sensitivity : -93.3 BLER : 5%

sensitivity : -96.3 BLER : 5%

sensitivity : -94.3 BLER : 5%

sensitivity : -94.3 BLER : 5%

sensitivity : -96.3 BLER : 5%

BAND 1 Reference sensitivity level(DUAL) BAND 2 Reference sensitivity level(DUAL) BAND 3 Reference sensitivity level(DUAL) BAND 4 Reference sensitivity level(DUAL) BAND 5 Reference sensitivity level(DUAL) BAND 7 Reference sensitivity level(DUAL) BAND 10 Reference sensitivity level(DUAL) 5/9 BAND 12 Reference sensitivity level(DUAL) BAND 13 Reference sensitivity level(DUAL) BAND 17 Reference sensitivity level(DUAL) BAND 20 Reference sensitivity level(DUAL) BAND 25 Reference sensitivity level(DUAL) BAND 26 Reference sensitivity level(DUAL) BAND 29 Reference sensitivity level(DUAL) BAND 30 Reference sensitivity level(DUAL) BAND 41 Reference sensitivity level(DUAL) BAND 66 Reference sensitivity level(DUAL) BAND 71 Reference sensitivity level(DUAL) Measure BLER of Mid Channel (5095) in Band12 Measure BLER of Mid Channel (5230) in Band13 Measure BLER of Mid Channel (5790) in Band17 Measure BLER of Mid Channel (6300) in Band20 Measure BLER of Mid Channel (8365) in Band25 Measure BLER of Mid Channel (8865) in Band26 Measure BLER of Mid Channel (9715) in Band29 Measure BLER of Mid Channel (9820) in Band30 Measure BLER of Mid Channel (40620) in Band41 Measure BLER of Mid Channel (66886) in Band66 Measure BLER of Mid Channel (68761) in Band71 sensitivity : -93.3 BLER : 5%

sensitivity : -93.3 BLER : 5%

sensitivity : -93.3 BLER : 5%

sensitivity : -93.3 BLER : 5%

sensitivity : -92.8 BLER : 5%

sensitivity : -94.5 BLER : 5%

CA operation CA operation sensitivity : -94.3 BLER : 5%

sensitivity : -95.8 BLER : 5%

sensitivity : -93.5 BLER : 5%

6/9 2.2 WCDMA Specification 2.2.1 WCDMA RX Sensitivity The Receiver Sensitivity of the TM04ANNABM0 are specified in the following table. Table8. Conducted RX (Receive) Sensitivity WCDMA Bands Item Method (DL CH) Specification Measure BER of Middle Channel (CH=10700) in Band1 0.1% @-106.7dBm Measure BER of Middle Channel (CH=9800) in Band2 0.1% @-106.7dBm Measure BER of Middle Channel (CH=1338) in Band3. 0.1% @-106.7dBm Measure BER of Middle Channel (CH=1675) in Band4. 0.1% @-106.7dBm Measure BER of Middle Channel (CH=4400) in Band5 0.1% @-106.7dBm 2.3 GSM Specification The Receiver Sensitivity of the TM04ANNABM0 are specified in the following table. BAND Method (DL CH) Specification Measure BER of Middle Channel (CH=190) 0~2.439%@-102dBm Measure BER of Middle Channel (CH=660) 0~2.439%@-102dBm BAND1 BER(Bit Error Rate) BAND2 BER(Bit Error Rate) BAND3 BER(Bit Error Rate) BAND4 BER(Bit Error Rate) BAND5 BER(Bit Error Rate) GSM850 Reference sensitivity level GSM1900 Reference sensitivity level 7/9 3. Antenna requirement [WWLAN]

This device contains BEJ-TM04ANNABM0 [FCC ID], 2703H-TM04ANNABM0

[ISED ID] as WWAN module. All the configuration related to the module comply module requirement with following antenna gain.

- An antenna may be connected to connector within following condition.

- This product has been tested with antenna and cable configuration listed below. Host manufacturer shall use antenna and cable that has gain less or equal to the configuration.

- Antenna gain calculated with cable loss and gain shall not be greater than final antenna gain listed below. Frequency-

Range UL [MHz]

Max Tx Gain

[dBi]

Band GSM 850 GSM 1900 UMTS B. 2 UMTS B. 4 UMTS B. 5 LTE 2 LTE 4 LTE 5 LTE 7 LTE 12 LTE 13 LTE 17 LTE 25 LTE 26 LTE 41 LTE 66 LTE 71

-1.9 2.0 2.0 2.6

-1.9 2.0 2.6

-1.9 2.7

-2.1

-0.1

-2.1 2.1

-1.1 2.7 2.6

-4.2 824 849 1850 1910 1850 1910 1710 1755 824 849 1850- 1910 1710 - 1755 824 - 849 2500 - 2570 699 - 716 777 - 787 704 - 716 1850 - 1915 814 - 849 2496 - 2690 1710- 1780 663 - 698 8/9 4. Label Requirement OEM host manufacturer must label Contains FCC ID: BEJ-TM04ANNABM0, Contains IC: 2703H-TM04ANNABM0. 4. Warning Statement FCC Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. ISED Warning This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter unless authorized to do so by the ISED. Cet appareil est conforme aux limites d'exposition aux rayonnements de lISDE pour un environnement non contrl. L'antenne doit tre installe de faon garder une distance minimale de 20 centimtres entre la source de rayonnements et votre corps. L'metteur ne doit pas tre colocalis ni fonctionner conjointement avec autre antenne ou autre metteur, moins d'y tre autorise par I'ISDE. 9/9

BMW WAVE LOW NAD Laser Marking Spec. IC: xxxxxxxxx FCC ID: xxxxxxx IC FCC ID Model #

QR Code EBR PID NA IC : 2703H-TM04ANNABM0 FCC ID: BEJ-TM04ANNABM0

- Model # : TM04ANNABM0

EBR : EBR31179001

* N/A : Not Available (No Marking), * TBD : To Be Determined (Need to mark)

BMW WAVE LOW NAD Laser Marking Spec. IC EBR PID Model #

QR Code NA IC : 2703H-TM04ANNABM0 FCC ID : BEJ-TM04ANNABM0

- Model # : TM04ANNABM0 EBR : EBR31179001

FCC ID

* N/A : Not Available (No Marking), * TBD : To Be Determined (Need to mark)

LG Electronics USA Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: July 01, 2022 Subject; Request for Confidentiality FCC ID: BEJ-TM04ANNABM0 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Sung Soo Kim Title: Director, Regulatory and Environmental Affairs

LG Electronics USA Date: July 01, 2022 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: BEJ-TM04ANNABM0 Applicant: LG Electronics USA Dear Examiner, This is to request a Class II Permissive change for FCC ID: BEJ-TM04ANNABM0 originally granted on July 14, 2020 (date). The change under this application is to the Addition of Antenna. Addition of Antenna Original Antenna Name: 9825131_02 1. Antenna Name: 920-631-001 2. Antenna Name: 8705921 3. Antenna Name: 920-631-002 I attest that the certified device will not be capable of ad-hoc mode operation outside of the grant conditions. FCC_Class II PC request letter Rev1.0_Revision 01 LG Electronics USA 1. Antenna Information We have additional antenna gain was measured in each band. Frequency-

Range UL () Band 9825131_02

[Original Grant]

920-631-001

[C2PC]

Increased Gain 8705921

[C2PC]

Increased Gain 920-631-002

[C2PC]

Increased Gain 663 698 LTE B71

-4.20 dBi 1.40 dBi 5.60 dB

-3.00 dBi 1.20 dB 1.20 dBi 5.40 dB 699 - 716 LTE B12

-2.10 dBi 1.40 dBi 3.50 dB 3.00 dBi 5.10 dB 1.70 dBi 3.80 dB 704 - 716 LTE B17

-2.10 dBi 1.40 dBi 3.50 dB 3.00 dBi 5.10 dB 1.70 dBi 3.80 dB 777 - 787 LTE B13

-0.10 dBi 1.60 dBi 1.70 dB 3.00 dBi 3.10 dB 1.70 dBi 1.80 dB 814 - 849 B26

-1.10 dBi 2.10 dBi 3.20 dB 3.00 dBi 4.10 dB 2.30 dBi 3.40 dB 824 - 849

-1.90 dBi 1.20 dBi 3.10 dB 3.00 dBi 4.90 dB 1.10 dBi 3.00 dB 1710 - 1755 2.60 dBi 3.30 dBi 0.70 dB 5.00 dBi 2.40 dB 3.30 dBi 0.70 dB 1710 - 1780 LTE B66 2.60 dBi 3.30 dBi 0.70 dB 5.00 dBi 2.40 dB 3.30 dBi 0.70 dB 1850- 1910 2.00 dBi 2.40 dBi 0.40 dB 5.00 dBi 3.00 dB 2.00 dBi 0.00 dB 1850 - 1915 LTE B25 2.10 dBi 2.40 dBi 0.30 dB 5.00 dBi 2.90 dB 2.00 dBi

-0.10 dB 2496 - 2690 LTE B41 2.70 dBi 6.60 dBi 3.90 dB 5.00 dBi 2.30 dB 6.50 dBi 3.80 dB 2500 - 2570 LTE B7 2.70 dBi 6.60 dBi 3.90 dB 5.00 dBi 2.30 dB 6.50 dBi 3.80 dB WCDMA V, LTE B5, GSM 850 WCDMA IV, LTE B4 WCDMA II, GSM 1900, LTE B2 This product is a professional installation equipment and installed by vehicle manufacturer. As antennas will be installed by vehicle manufacturer. 2. E.R.P./ E.I.R.P. Due to increasing some antenna gain, E.R.P./ E.I.R.P. was recalculated to comply the limits in Parts 22, 24, 27, and 90 of FCC rules Sincerely, Name: Sung Soo Kim Title: Director, Regulatory and Environmental Affairs Date: July 01, 2022 Signature of applicant:

FCC_Class II PC request letter Rev1.0_Revision 01

Letter of Authorization Company Address

: LG Electronics USA

: 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, 07632, United States

: TM04ANNABM0

: Telematics Module

: BEJ-TM04ANNABM0 Product Name Model Number FCC Identifier We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Sung Soo Kim Title: Director, Regulatory and Environmental Affairs Date: July 01, 2022 Signature of applicant:

LG Electronics USA 1000 Sylvan Ave Englewood Cliffs, NJ 07632-0763 United States April 22, 2021 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad, Columbia,MD21046 LETTERFORAUTHORIZATION FCC ID: BEJ-TM04ANNABM0 Towhomitmayconcern:

I,theundersigned,herebyauthorizeLabManagerHyunchae You (or Jungmin Yang) andof SGS KoreaCo.,Ltd.andhereafterreferredtoasSGSKorea,toactonourbehalfinallmanners relatingtoapplicationforequipmentauthorization,includingsigningofalldocumentsrelating tothesematters.AnyandallactscarriedoutbyLabManagerHyunchae You(orJungmin Yang)of SGSKoreaCo.,Ltd.onourbehalfshallhavethesameeffectasactsofourown. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includesFCCbenefits,pursuanttoSection5301oftheAntiDrugAbuseActof1988,21U.S.C. 853(a). InauthorizingSGSKoreaasouragent,westillrecognizethatweareresponsibleto:

a) complywiththerelevantprovisionsofthecertificationprogram;

b) makeallnecessaryarrangementsfortheconductoftheevaluation,includingprovision forexaminingdocumentationandaccesstoallareas,records(includinginternalaudit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment,surveillance,reassessment)andresolutionofcomplaints;

c) makeclaimsregardingcertificationonlyinrespectofthescopeforwhichcertification hasbeengranted;

d) do not use our product certification in such a manner as to bring the Certification Divisionintodisreputeandnotmakeanystatementregardingourproductcertification whichtheCertificationDivisionmayconsidermisleadingorunauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any referencethereto and returnanycertification documents as requiredbytheCertificationDivision;

f) usecertificationonlytoindicatetheproductsarecertifiedasbeinginconformitywith specifiedstandards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleadingmanner;

h) ensurethatanyreferencetoourproductcertificationincommunicationmediasuchas documents, brochures or advertising, complies with the requirements of the CertificationDivision;

LG Electronics Inc. 222 LG-ro, Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, 451-713, Korea TEL: +82-31-610-6193 i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records availabletotheCertificationDivisionwhenrequested;

takeappropriateactionwithrespecttosuchcomplaintsandanydeficienciesfoundin productsorservicesthataffectcompliancewiththerequirementsforcertification;

k) documenttheactionstaken. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours Dae Woong Kim Director, NA Regulatory and Environmental Affairs LGElectronicsInc.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name LG Electronics USA 1000 Sylvan Avenue, Englewood Cliffs, New Jersey 07632 USA Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Dae Woong Kim BEJ BEJ-TM04ANNABM0 daewoong.kim@lge.com

+1-201-266-2215 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. a) b) c) d) e) f) g) Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: 22 April 2021 Print Name:

Dae Woong Kim Title:

Director, NA Regulatory and Environmental Affairs

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States July 07, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: BEJ-TM04ANNABM0 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552

(b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

Confidential List Long-Term Short-Term Block Diagram Operational Description Schematics Tune-up procedure Part list External Photos Internal Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, Kyungsu Han Director Standards & Compliance LG Electronics USA

LETTER OF REQUEST PERMISSIVE CHANGE 26 April 2021 We, as a manufacturer of following equipment, hereby submit Class 2 Permissive Change application for the FCC and the ISED to change components in the filings. MODEL FCC ISED FCC ID BEJ-TM04ANNABM0 Certification Number 2703H-TM04ANNABM0 TM04ANNABM0 Original Grant Date 14 July 2020 Original Grant Date 27 May 2020 Equipment Type Single Modular A. Antenna Information We have additional antenna called 9825131_04 and gain was measured in each band. Frequency-

Range UL () Band 9825131_02

[Original Grant]

9825131_04

[C2PC]

Increased Gain B71 B12 B17 B13 B26 B5 B4 B66 B2 B25 B41 B7

-4.2 dBi

-2.1 dBi

-2.1 dBi

-0.1 dBi

-1.1 dBi

-1.9 dBi 2.6 dBi 2.6 dBi 2.0 dBi 2.1 dBi 2.7 dBi 2.7 dBi

-3.4 dBi

-3.1 dBi

-3.1 dBi

-0.4 dBi 0.0 dBi

-0.2 dBi 2.8 dBi 3.0 dBi 2.3 dBi 2.3 dBi N/A N/A 0.8 dB

-1.0 dB

-1.0 dB

-0.3 dB 1.1 dB 1.7 dB 0.2 dB 0.4 dB 0.3 dB 0.2 dB N/A N/A This product is a professional installation equipment and installed by vehicle manufacturer. As antennas will be installed by vehicle manufacturer. Vehicle manufacturer will implement specific software version for each antenna and vehicle. LTE B7 and B41 shall be disabled by the software when the antenna 98525131_04 is installed on this equipment. Therefore, antenna gain of B7 and B41 from excluded from this C2PC request and remain unchanged as original grant. According to the KDB 178919 and KDB 996369, host manufacturer can use antenna has gain less than following table. 663 698 699 - 716 704 - 716 777 - 787 814 - 849 824 - 849 1710 - 1755 1710 - 1780 1850- 1910 1850 - 1915 2496 - 2690 2500 - 2570 Band GSM 1 900 GSM 850 WCDMA WCDMA Frequency

() 1 850 - 1 910 824 - 849 1 850 - 1 910 1 710 - 1 755 Antenna Gain

(i) 2.3

-0.2 2.3 2.8 824 - 849 2500 - 2570 699 716 777 787 1 850 1 915 814 824

(Only for FCC) 824 849 2496 - 2690 1 710 - 1 780 663 - 698 WCDMA LTE 7 LTE 12/17 LTE 13 LTE 25/2 LTE 26 LTE 26/5 LTE 41 LTE 66/4 LTE 71 Frequency-

Range UL () 663 698 699 - 716 704 - 716 777 - 787 814 - 849 824 - 849 1710 - 1755 1710 - 1780 1850- 1910 1850 - 1915 2496 - 2690 2500 - 2570 B71 B12 B17 B13 B26 B5 B4 B66 B2 B25 B41 B7 B. WORST CASE SELECTION The worst-case scenarios have been chosen based on these Gain values and Margin of Radiated Spurious Emission.

- Bands which Increase above 0.5 dB (below 0.5 dB is expected to be affected by uncertainty)

- Bands which have below 5 dB on Margin of Radiated Spurious Emission [Original Grant]

Band Increased Gain RSE Margin [Original Grant]

GSM WCDMA LTE Additional RSE LTE B71

*LTE B26 LTE B25 Not used Not used 29.58 dB 50.46 dB B12 47.58 dB 20.05 dB

B26 B66 B25 3.08 3.03 4.80 0.8 dB

-1.0 dB

-1.0 dB

-0.3 dB 1.1 dB 1.7 dB 0.2 dB 0.4 dB 0.3 dB 0.2 dB N/A N/A 34.41 dB

37.90 dB

20.47 dB

*B26 is chosen by higher antenna gain than B5. [The Gain of B26 is 0.0 dBi / The Gain of B5 is -0.2 dBi]

-0.2 2.7

-2.1

-0.1 2.3 0.0

-0.2 2.7 3.0

-3.4 C. E.R.P./ E.I.R.P. Due to increasing some antenna gain, E.R.P./ E.I.R.P. was recalculated to comply the limits in Parts 22, 24, 27, and 90 of FCC rules and RSS standards. Band Frequency

() Target Power

(m) Max Tune-up Tolerance

() Maximum Conducted Power

(m) Maximum Conducted Power

(W) Antenna Gain

(i) Maximum E.I.R.P.

(m) Maximum E.I.R.P.

(W) Maximum E.R.P.

(m) Maximum E.R.P.

(W) Output Power Limit GSM 1 900 GSM 850 WCDMA WCDMA WCDMA LTE 25/2 LTE 26 LTE 26/5 LTE 66/4 LTE 71 1 850 - 1 910 30.00 0.70 30.70 1.175 2.3 33.00 1.995 824 - 849 33.00 2.50 35.50 3.548

-0.2 35.30 3.388 33.15 2.065 1 850 - 1 910 24.00 1.70 25.70 0.372 2.3 28.00 0.631 1 710 - 1 755 24.00 1.70 25.70 0.372 2.8 28.50 0.708 824 - 849 24.00 1.70 25.70 0.372

-0.2 25.50 0.355 23.35 0.216 1 850 - 1 915 23.00 2.70 25.70 0.372 2.3 28.00 0.631 814 - 824

(Only for FCC) 23.00 2.70 25.70 0.372 0.0 25.70 0.372 23.55 0.226 824 - 849 23.00 2.70 25.70 0.372

-0.2 25.50 0.355 23.35 0.216 1 710 - 1 780 23.00 2.70 25.70 0.372 3.0 28.70 0.741 663 - 698 23.00 2.70 25.70 0.372

-3.4 22.30 0.170 20.15 0.104 2 W E.I.R.P. 7 W E.R.P. 2 W E.I.R.P. 1 W E.I.R.P. 7 W E.R.P. 2 W E.I.R.P. 100 W E.R.P. 7 W E.R.P. 1 W E.I.R.P. 3 W E.R.P.

*Maximum antenna gains for LTE B7, B12, B13, B17, and B41 are same as original grant. Remark;

1. E.I.R.P. ( m) = Maximum Conducted Power ( m) + Antenna Gain ( i) 2. E.R.P. ( m) = E.I.R.P. ( m) - 2.15 (); where E.R.P. and E.I.R.P. are expressed in consistent units. D. Declaration The model with additional antenna comply ERP/EIRP requirements, power thresholds for exemption from routine evaluation, MPE limits at 20cm and the limits in Parts 22, 24, 27, and 90 of FCC rules and RSS standards. Based on technical analysis mentioned above, we hereby request permissive change for both FCC and ISED certification. Director, Regulatory and Environmental Affairs LG Electronics USA, Inc. Mr. Dae Woong Kim Phone: 201-266-2215

Cover Letter-Modular Approval FCC ID: BEJ-TM04ANNABM0 Date: 9 July 2020 Gentlemen:

Theres a Bluetooth Module that would like to have your authorization as a modular approval. The specific product as below, Bluetooth Module, with its designed features and specified description, meets special requirements for full modular approval on Requirement of RSP-100 issue 10 Section 7.3 by cross-reference list below. Company Model Name Model Number FCC ID LG Electronics Inc. Telematics Module TM04ANNABM0 BEJ-TM04ANNABM0 ComplyY/N Y in the radio elements shall have radio a)The frequency circuitry shielded. Physical / discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. b)The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out the applicable RSS standard under conditions of excessive data rates or over-

modulation. c)The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. d)The module shall comply with the provisions for external power amplifiers and antennas detailed in the applicable RSS standard. The equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. e) The module shall be tested for compliance with the stand-alone configuration, i.e. the module must not be inside another device during testing. f) The module shall comply with the Category I equipment labelling requirements. applicable standard in a g) The module shall comply with applicable RSS-

102 exposure requirements, which are based on the intended use/configurations. Y Y

. Y Y Y Y h)Is the modular device for an Industry Canada licence-exempt service?

Y By:

(Signature1) Kyung-Su Han

(Print name) Thank you. Sincerely, Title: Director On behalf of:

LG Electronics Inc.

(Company Name) Telephone:

201-472-2623