FCC ID: BEJTN1T23NR Telematics

LG Electronics Inc. 1 23-1-31 1. Product Introduction User Manual TN1T23NR supports GSM, WCDMA, LTE and 5G NR for vehicle telecommunication. Host ID: TN1T23NR, TN1T23NE FCC ID: BEJTN1T23NR Major functions of BMW Wave Multi-mode RAT communication GSM, WCDMA, LTE and 5G NR. The RF platform of TN1T23NR supports highly integrated RF transceiver, with all necessary features to enable multi mode, multi band car telematics applications. It incorporates a fully integrated dual mode receiver, multi band TX outputs, TCVCXO control, a measurement interface and DSDA (Dual SIM Dual Active). TN1T23NR module compliant high speed data and control interface, a multi mode timer unit and all necessary front end signals for the complete RF Engine control. Overall the TN1T23NR directly supports RF engines with up to 5G bands. 1.1 TN1T23NR Block Diagram Confidential 1.2 Environmental Specifications The environmental specification for operating and storage of the TN1T23NR are defined in the table below. Table 2. Environmental Specifications Parameter Temperature Range Operating Temperature

-40 to 90 (ecall 95) Storage Temperature Humidity

-40 to +90 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TN1T23NR embedded modules. 1/5 LG Electronics Inc. 2 23-1-31 Recommend Operating voltage Parameter VBATT VIN Power Supply Input Voltage on any digital input or output pin 1.3.1 Absolute Maximum Rating and ESD Ratings Min

Typical 12 12 Units V V This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TN1T23NR embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter VBATT VIN ESD Ratings ESD1) Power Supply Input Voltage on any digital input or output pin Min

Max 18 18 Units V V Primary, Diversity antenna pads -

Contact 10 kV 1) The ESD Simulator configured with 330pF, 2000. Caution: The TN1T23NR embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TN1T23NR devices. 1.3.2 Current Consumption Table 4. TN1T23NNCRE Current Consumption (12.5V) Mode Parameter Active SIM1 only operation (Tx max output) Active DSDA operation (Tx max output) Sleep Sleep Mode, Average Current Typical 600 1000 0.03 Max 1000 2000 Units mA mA mA 2/5 LG Electronics Inc. 3 23-1-31 2. Mechanical Specifications 2.1 Physical Dimensions Size : 160 x 100 x 18mm Weight : 308.7g Mechanical Design 3/5 LG Electronics Inc. 4 23-1-31 Device Connector 4/5 LG Electronics Inc. 5 23-1-31 3. TN1T23NR RF Specification SIM1 (OEM SIM) Support Band Band Tx Rx B2 B4 B5 B7 1850~1910 1930~1990 1710~1755 2110~2155 824~849 869~894 2500~2570 2620~2690 B12(B17) 699~716 777~787 729~746 746~756 B13 B25 B26 B41 1850~1915 1930~1995 814~849 859~894 2496~2690 2496~2690 FDD/

TDD FDD FDD FDD FDD FDD FDD FDD FDD TDD Band TN1T23NR TN1T23NE W, L W, L W, L L L Mid Mid Low High Low Low Mid Low G, W, L W, L G, W, L L L L High L, 5G(N,S)

- G(GSM), W(WCDMA), T(TD-SCDMA), L(LTE), 5G(N)-NSA, 5G(S)-SA SIM2 (Consumer SIM) Support Band Band Tx Rx FDD/TDD Band TN1T23NR TN1T23NE B2 B4 B5 B7 B26 B41 1850~1910 1930~1990 1710~1755 2110~2155 824~849 869~894 2500~2570 2620~2690 814~849 859~894 2496~2690 2496~2690 FDD FDD FDD FDD FDD TDD Mid Mid Low High Low High G, L L G, L L L L, 5G(S) L

- G(GSM), W(WCDMA), T(TD-SCDMA), L(LTE), 5G(N)-NSA, 5G(S)-SA 4. Notice Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer (or party responsible) for compliance could void the users authority to operate the equipment This equipment complies with FCC and IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. 5/5

1. Label Information Model No. : TN1T23NR, TN1T23NE (Telematics) Variant : NA/EU/CN/ROW (Mecha Type : Roof /Trunk) Label Size : Main Label - 62 X 40 mm Regulation Label - 60 X 34 mm Label Material 1) Paper : Avery MZ1061J1 2) Adhesive : SP4200 3) Liner : G60Em Label Attachment Location on the Product Main Label Sub Label FCC ID: BEJTN1T23NR

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 February 09, 2023 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad, Columbia,MD21046 LETTERFORAUTHORIZATION FCC ID: BEJTN1T23NR Towhomitmayconcern:

I,theundersigned,herebyauthorizeSGS KoreaCo.,Ltd. andhereafterreferredtoasSGS Korea,toactonourbehalfinallmannersrelatingtoapplicationforequipmentauthorization, includingsigningofalldocumentsrelatingtothesematters.Anyandallactscarriedoutby SGSKoreaCo., Ltd.onourbehalfshallhavethesameeffectasactsofourown. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includesFCCbenefits,pursuanttoSection5301oftheAntiDrugAbuseActof1988,21U.S.C. 853(a). InauthorizingSGSKoreaasouragent,westillrecognizethatweareresponsibleto:

a) complywiththerelevantprovisionsofthecertificationprogram;

b) makeallnecessaryarrangementsfortheconductoftheevaluation,includingprovision forexaminingdocumentationandaccesstoallareas,records(includinginternalaudit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment,surveillance,reassessment)andresolutionofcomplaints;

c) makeclaimsregardingcertificationonlyinrespectofthescopeforwhichcertification hasbeengranted;

d) do not use our product certification in such a manner as to bring the Certification Divisionintodisreputeandnotmakeanystatementregardingourproductcertification whichtheCertificationDivisionmayconsidermisleadingorunauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any referencethereto and returnanycertification documents as requiredbytheCertificationDivision;

f) usecertificationonlytoindicatetheproductsarecertifiedasbeinginconformitywith specifiedstandards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleadingmanner;

h) ensurethatanyreferencetoourproductcertificationincommunicationmediasuchas documents, brochures or advertising, complies with the requirements of the CertificationDivision;

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records availabletotheCertificationDivisionwhenrequested;

takeappropriateactionwithrespecttosuchcomplaintsandanydeficienciesfoundin productsorservicesthataffectcompliancewiththerequirementsforcertification;

k) documenttheactionstaken. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours Mr. Heejae Cho Director, Regulatory & Environmental Affairs LG Electronics USA, Inc.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name LG Electronics USA Applicant Declaration Address Grantee Code FCC ID Authorized Contact Name Contact Email Contact Phone 111 Sylvan Ave, North Building, Englewood Cliffs, NJ 07632 United States BEJ BEJTN1T23NR Heejae Cho heejae.cho@lge.com 201-470-2696 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) g) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List LG Electronics USA (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. LG Electronics USA (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to 1.50002, as an entity producing covered equipment. Applicant Signature:

Date: February 09, 2023 Print Name: Heejae Cho Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Director, Regulatory and Environmental Affairs QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 February 09, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: BEJTN1T23NR Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

Long-Term CONFIDENTIAL LIST Short-Term 1 2 3 4 5 6 7 8 9 10 External Photos Internal Photos Test-Setup Photos User Manual Operational Description Block Diagram Schematics PCB Layout Part List Tune-Up Procedure The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours Heejae Cho Director, NA Regulatory & Environmental Affairs LG Electronics USA, Inc.

Declaration of Equivalence We, LG Electronics Inc., as manufacturer of following product hereby declare equality of following devices. Those models are technically identical, but the only difference is cellular portion. Model Name TN1T23NR TN1T23NE Remark Basic Model Market in EU Model Description The Models are TN1T23NR and TN1T23NE have following differences.

- Common PCB design but the component Pop or de-pop Model TN1T23NR TN1T23NE Differences Hardware Part Reference Remove Band21 related parts Remove QPM5679AQ, QDM5679AQ Description Fully Mounted on hardware. not support LTE Band21 not support 5G NR n79

*Difference between two models does not affect bands that can be used in the US.

- Supported Cellular Band Module / Model Mode SIM1 GSM GSM850, PCS1900 WCDMA B2, B4, B5 SIM2 GSM850, PCS1900 N/A TN1T23NR LTE B2, B4, B5, B7, B12(B17), B26, B41 B2, B4, B5, B7, B26, B41 5G Sub6_SA n41 5G Sub6_NSA GSM n41 N/A WCDMA B2, B4, B5 TN1T23NE LTE B2, B4, B5, B7, B12(B17) 5G Sub6_SA N/A 5G Sub6_NSA N/A

*Operating bands are different by Software. n41 N/A N/A N/A B7 N/A N/A TN1T23NE ENDC Combination [SIM1]

NSA n41 TN1T23NR DC_5A_n41A DC_26A_n41A December 14, 2022 LG Electronics Inc. Seungho Hur seungho.hur@lge.com

UNITED STATES DESIGNATED AGENT LETTER Date: February 9, 2023 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name: LG Electronics USA Grantee Code:

BEJ Contact Name:

Heejae Cho Address:

111 Sylvan Ave, North Building, Englewood Cliffs, NJ City/Province/Zip: Englewood Cliffs/New Telephone:

Fax:

Email:

Jersey/07632 201-470-2696 201-816-20031 heejae.cho@lge.com Applicable Equipment: FCC ID: <BEJTN1T23NR>

ATTN: Director of Certification:

U.S. designated agent Company Name: LG Electronics USA Contact Name:

Address:

Heejae Cho 111 Sylvan Ave, North Building, Englewood Cliffs, NJ City/Province/Zip: Englewood Cliffs/New Jersey/07632 Telephone:

201-470-2696 Fax:

Email:

201-816-20031 heejae.cho@lge.com We, < LG Electronics USA > understand and acknowledge the applicants consent and the designated agents obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < LG Electronics USA > acknowledge the applicants acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Heejae Cho Name (Printed): Heejae Cho Title: Director, Regulatory and Environmental Affairs Title: Director, Regulatory and Environmental Affairs Signature:

Signature: