all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
statement of security code | Users Manual | 40.10 KiB | April 06 2007 / May 06 2007 | |||
1 |
|
users manual | Users Manual | 3.77 MiB | April 06 2007 / May 06 2007 | |||
1 | Cover Letter(s) | April 06 2007 / May 06 2007 | ||||||
1 | Cover Letter(s) | April 06 2007 / May 06 2007 | ||||||
1 | External Photos | April 06 2007 / May 06 2007 | ||||||
1 | Internal Photos | April 06 2007 / May 06 2007 | ||||||
1 | ID Label/Location Info | April 06 2007 / May 06 2007 | ||||||
1 | RF Exposure Info | April 06 2007 / May 06 2007 | ||||||
1 | Test Report | April 06 2007 / May 06 2007 | ||||||
1 | Test Setup Photos | April 06 2007 / May 06 2007 |
1 | statement of security code | Users Manual | 40.10 KiB | April 06 2007 / May 06 2007 |
Panasonic Communications Co., Ltd. FCC ID : ACJ96NKX-TDA0152 STATEMENT OF SECURITY CODE This wireless handset has 1000 billion digital security coding combinations that are provided by the following means:
Provided with 40 bits (1000 billion) for security codes.. When shipped from the factory, the security code is decided by the manufacturer. 1 of 1
1 | users manual | Users Manual | 3.77 MiB | April 06 2007 / May 06 2007 |
Pure IP-PBX Installation Manual KX-TDE100 Model KX-TDE200 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. KX-TDE100/KX-TDE200: PMMPR Software File Version 1.0000 or later SD Logo is a trademark. Document Version: 2007-02 System Components System Components Table Category Model No. Description Shelves KX-TDE100 KX-TDE200 Basic Shelf Basic Shelf Main Processing Card IP Convergence Main Processing Card (IPCMPR) IPCMPR Option Cards KX-TDE0110 16-Channel VoIP DSP Card (DSP16) KX-TDE0111 KX-TDA0196 64-Channel VoIP DSP Card (DSP64) Remote Card (RMT) Activation Key Cards KX-NCS4104 4-Channel IP Trunk Activation Key (SHGW4) KX-NCS4208 KX-NCS4508 KX-NCS4716 KX-NCS4910 Virtual CO Line Card Virtual Extension Cards
8-Channel IP Softphone/IP Proprietary Telephone Activation Key (IPPTS8) 8-Channel IP Proprietary Telephone Activation Key (IPPT8) 16-Channel SIP Extension Activation Key (SPE16) Activation Key for Software Upgrade to Enhanced Version
(UCAV2) Virtual 16-Channel VoIP Gateway Card (V-IPGW16) Virtual 32-Channel VoIP Extension Card (V-IPEXT32) Virtual 32-Channel SIP Extension Card (V-SIPEXT32) Physical CO Line Cards KX-TDA0180 8-Port Analog Trunk Card (LCOT8) KX-TDA0181 KX-TDA0187 KX-TDA0193 KX-TDA0290 KX-TDA0484 KX-TDA0490 16-Port Analog Trunk Card (LCOT16) T-1 Trunk Card (T1) 8-Port Caller ID Card (CID8) PRI Card (PRI23) 4-Channel VoIP Gateway Card (IP-GW4E) 16-Channel VoIP Gateway Card (IP-GW16) 2 Installation Manual System Components Table Category Model No. Description Physical Extension Cards KX-TDA0143 4 Cell Station Interface Card (CSIF4) KX-TDA0144 KX-TDA0170 KX-TDA0171 KX-TDA0172 KX-TDA0173 KX-TDA0174 KX-TDA0175 8 Cell Station Interface Card (CSIF8) 8-Port Digital Hybrid Extension Card (DHLC8) 8-Port Digital Extension Card (DLC8) 16-Port Digital Extension Card (DLC16) 8-Port Single Line Telephone Extension Card (SLC8) 16-Port Single Line Telephone Extension Card (SLC16) 16-Port Single Line Telephone Extension with Message Lamp Card (MSLC16) Other Physical Cards KX-TDA0161 4-Port Doorphone Card (DPH4) KX-TDA0470 16-Channel VoIP Extension Card (IP-EXT16) KX-TDA0164 KX-TDA0166 KX-TDA0168 KX-TDA0190 KX-TDA0191 KX-TDA0103 KX-TDA0104 KX-TDA0108 4-Port External Input/Output Card (EIO4) 16-Channel Echo Canceller Card (ECHO16) Extension Caller ID Card (EXT-CID) Optional 3-Slot Base Card (OPB3) 4-Channel Message Card (MSG4) L-Type Power Supply Unit (PSU-L) M-Type Power Supply Unit (PSU-M) S-Type Power Supply Unit (PSU-S) Power Supply Units
(PSUs) Cell Stations
(CSs) Basic CSs KX-T0141 KX-TDA0142 KX-T0151 KX-TDA0152 2-Channel Cell Station Unit Using a DHLC/DLC Card (PT-
interface CS) for 2.4 GHz Portable Station 3-Channel Cell Station Unit Using a CSIF Card for 2.4 GHz Portable Station 2-Channel Cell Station Unit Using a DHLC/DLC Card (PT-
interface CS) for 2.4 GHz Portable Station 3/4-Channel Cell Station Unit Using a CSIF Card for 2.4 GHz Portable Station High-density CSs KX-TDA0158 5-Channel High-density Cell Station Unit Using a DHLC/DLC Card (PT-interface CS) for 2.4 GHz Portable Station Proprietary Equipment KX-A258 Blank Slot Cover KX-T30865 Doorphone Installation Manual 3 Compatible Panasonic Proprietary Telephones The PBX supports the following telephones:
IP proprietary telephones (e.g., KX-NT300 series) IP softphones (e.g., KX-NCS8100) Digital proprietary telephones (e.g., KX-T7600 series) Analog proprietary telephones (e.g., KX-T7700 series) Portable stations (e.g., KX-TD7690) DSS consoles (e.g., KX-T7640) Note KX-NT300 series IP-PTs are supported by the IPCMPR card, but not by the IP-EXT16 card. In contrast, KX-NT136 and KX-NT265 IP-PTs are supported by the IP-EXT16 card, but not by the IPCMPR card. Only the KX-NT265 (D) IP-PT is supported by both cards. Incompatible Panasonic Proprietary Telephones The PBX does not support the following telephones:
KX-T30800 series proprietary telephones and DSS consoles KX-T61600 series proprietary telephones and DSS consoles KX-T123200 series proprietary telephones and DSS consoles Notes
For the equipment (e.g., Add-on Key Module, USB Module, Headset*1) that can be connected to a particular telephone, refer to the telephone's manual. For other equipment that can be connected to the PBX, refer to "1.2.2 System Connection Diagram". List of Abbreviations APT Analog Proprietary Telephone DPT Digital Proprietary Telephone IP-PT IP Proprietary Telephone PS Portable Station PT Proprietary Telephone SIP Extension Session Initiation Protocol Extension (SIP hardphones/SIP softphones) SLT Single Line Telephone
Notice This PBX supports SIP Extensions. However, some PBX features may not be available for SIP Extensions, depending on your telephone type.
*1 The KX-T7090 headset can be connected to the KX-T7000, KX-T7200, KX-T7300, and KX-T7400 series telephones. 4 Installation Manual Important Notice Prior to connection of this product, please verify that the intended operating environment is supported. Satisfactory performance cannot be guaranteed for the following:
interoperability and compatibility with all devices and systems connected to this product proper operation and compatibility with services provided by telecommunications companies over connected networks Installation Manual 5 Important Safety Instructions SAFETY REQUIREMENTS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean with a damp cloth. 4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 5. Do not place the product on an unstable surface, as a fall may cause serious internal damage. 6. Slots and openings in the front, back and bottom of the cabinet are provided for ventilation; to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface while in use. The product should never be placed near or over a radiator or other heat source. This product should not be placed in a sealed environment unless proper ventilation is provided. 7. The product should only be connected to the type of electrical power supply specified on the product label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. 8. For safety purposes this unit is equipped with a grounded plug. If you do not have a grounded outlet, please have one installed. Do not bypass this safety feature by tampering with the plug. 9. Do not allow anything to rest on the power cord. Do not locate this product where the power cord may be stepped on or tripped on. 10. To reduce the risk of fire or electric shock, do not overload wall outlets and extension cords. 11. Do not insert objects of any kind into this product through its slots and openings, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on or in the product. 12. To reduce the risk of electric shock, do not disassemble this product. Only qualified personnel should service this product. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock. 13. Unplug this product from the wall outlet and have it serviced by qualified service personnel in the following cases:
a) When the power supply cord or plug is damaged or frayed. b) c) d) If liquid has been spilled into the product. If the product has been exposed to rain or water. If the product does not operate according to the operating instructions. Adjust only the controls that are explained in the operating instructions. Improper adjustment of other controls may result in damage and may require service by a qualified technician to restore the product to normal operation. If the product has been dropped or the cabinet has been damaged. If product performance deteriorates. e) f) 14. Avoid using wired telephones during an electrical storm. There is a remote risk of electric shock from lightning. 15. Do not use a telephone in the vicinity of a gas leak to report the leak. 6 Installation Manual SAVE THESE INSTRUCTIONS Installation Manual 7 Precaution WARNING NOT REMOVE DO CARD SD MEMORY WHILE IS SUPPLIED TO THE PBX POWER Doing so may cause the PBX to fail to start when you try to restart the system. 8 Installation Manual
Keep the unit away from heating appliances and devices that generate electrical noise such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the PBX. This unit should be kept free of dust, moisture, high temperature (more than 40 should not be exposed to direct sunlight. If you are having problems making calls to outside destinations, follow this procedure to test the CO lines:
1. Disconnect the PBX from all CO lines. 2. Connect known working SLTs to those CO lines. 3. Make a call to an external destination using those SLTs. If a call cannot be carried out correctly, there may be a problem with the CO line that the SLT is connected to. Contact your telephone company. If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the CO lines until it has been serviced by an authorized Panasonic Factory Service Center.
) and vibration, and C
Wipe the unit with a soft cloth. Do not clean with abrasive powders or with chemical agents such as benzene or thinner. WARNING
THIS UNIT MAY ONLY BE INSTALLED AND SERVICED BY QUALIFIED SERVICE PERSONNEL. IF DAMAGE TO THE UNIT EXPOSES ANY INTERNAL PARTS, DISCONNECT THE POWER SUPPLY CORD IMMEDIATELY AND RETURN THE UNIT TO YOUR DEALER. UNPLUG THIS UNIT FROM THE AC OUTLET IF IT EMITS SMOKE, AN ABNORMAL SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND CONTACT AN AUTHORIZED PANASONIC FACTORY SERVICE CENTER.
WHEN RELOCATING THE EQUIPMENT, FIRST DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION. WHEN THE UNIT IS INSTALLED IN THE NEW LOCATION, RECONNECT THE POWER FIRST, AND THEN RECONNECT THE TELECOM CONNECTION. TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE. ENSURE THAT THE AC OUTLET IS LOCATED NEAR THE EQUIPMENT AND IS EASILY ACCESSIBLE. DANGER OF EXPLOSION EXISTS IF A BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE BATTERY MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. THE SD MEMORY CARD POSES A CHOKING HAZARD. KEEP THE SD MEMORY CARD OUT OF REACH OF CHILDREN.
Installation Manual 9 Password Security Warning to the Administrator or Installer regarding the system password 1. Please provide all system passwords to the customer. 2. To avoid unauthorized access and possible abuse of the PBX, keep the passwords secret, and inform the customer of the importance of the passwords, and the possible dangers if they become known to others. 3. The PBX has default passwords preset. For security, change these passwords the first time that you program the PBX. 4. Change the passwords periodically. 5. 6. It is strongly recommended that passwords of 10 numbers or characters be used for maximum protection against unauthorized access. For a list of numbers and characters that can be used in system passwords, refer to "1.1.2 Entering Characters" in the PC Programming Manual. If a system password is forgotten, it can be found by loading a backup of the system data into a PC, and checking the password using the KX-TDA Maintenance Console software. If you do not have a backup of the system data, you must reset the PBX to its factory defaults and reprogram it. Therefore, we strongly recommend maintaining a backup of the system data. For more information on how to back up the system data, refer to "2.4.1 ToolSD memory backup" in the PC Programming Manual. However, as system passwords can be extracted from backup copies of the system data file, do not allow unauthorized access to these files. Notice for users in California This product contains a CR coin cell lithium battery that contains perchlorate materialspecial handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate 10 Installation Manual When you ship the product Carefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a postage-paid letter, detailing the symptom, to the outside of the carton. DO NOT send the product to the Executive or Regional Sales offices. They are NOT equipped to make repairs. Product Service Panasonic Factory Service Centers for this product are listed in the service center directory. Consult your certified Panasonic dealer for detailed instructions. For Future Reference Please print, record, and retain the following information for future reference. For Future Reference Please print, record, and retain the following information for future reference. Note The serial number of this product can be found on the label affixed to the unit. You should record the model number and the serial number of this unit as a permanent record of your purchase to aid in identification in the event of theft. MODEL NO. SERIAL NO. DATE OF PURCHASE NAME OF DEALER DEALER'S ADDRESS DEALER'S TEL. NO. Installation Manual 11 Introduction This Installation Manual is designed to serve as an overall technical reference for the Panasonic Pure IP-
PBX, KX-TDE100/KX-TDE200. It provides instructions for installing the hardware, and programming the PBX using the KX-TDE Maintenance Console. The Structure of this Manual This manual contains the following sections:
Section 1 System Outline Provides general information on the PBX, including the system capacity and specifications. Section 2 Activation Key Installation Describes information on activation keys, including how to obtain an activation key and install it in the SD Memory Card. Section 3 Installation Describes the procedures to install the PBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included. Section 4 Guide for the KX-TDE Maintenance Console Explains the installation procedure, structure, and basic information of the KX-TDE Maintenance Console. Section 5 Troubleshooting Provides information on the PBX and telephone troubleshooting. About the Other Manuals Along with this Installation Manual, the following manuals are available:
Feature Manual Describes all basic, optional and programmable features of the PBX. PC Programming Manual Provides step-by-step instructions for performing system programming using a PC. PT Programming Manual Provides step-by-step instructions for performing system programming using a PT. Operating Manual Provides operating instructions for end users using a PT, SLT, PS, or DSS Console. About the software version of your PBX The contents of this manual apply to PBXs with a certain software version, as indicated on the cover of this manual. To confirm the software version of your PBX, see "How do I confirm the software version of the PBX or installed cards?" in the FAQ of the PC Programming Manual, or "[190] Main Processing (MPR) Software Version Reference" in the PT Programming Manual. Trademarks
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Matsushita Electric Industrial Co., Ltd. is under licence.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries. Intel and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. 12 Installation Manual
All other trademarks identified herein are the property of their respective owners. Screen shots reprinted with permission from Microsoft Corporation. Installation Manual 13 F.C.C. REQUIREMENTS AND RELEVANT INFORMATION 1. Notification to the Telephone Company This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this equipment is a label that contains, among other information, a product identifier in the following format:
US:AAAEQ##TXXXX If requested, this number must be provided to the telephone company. Installation must be performed by a qualified professional installer. If required, provide the telephone company with the following technical information:
Telephone numbers to which the system will be connected
Make: Panasonic
Model: KX-TDE100 and KX-TDE200
Certification No.: found on the side of the unit Ringer Equivalence No.: 0.3A Facility Interface Code: 02LS2, 04DU9.BN/DN/1KN/1SN, METALLIC Service Order Code: 9.0F, 6.0P Required Network Interface Jack: RJ21X, RJ48C, RJ2HX 2. Ringer Equivalence Number (REN) The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the following format:
US:AAAEQ##TXXXX 3. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. Incidence of Harm to the Telephone Lines If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. 4. Changes in Telephone Company Communications Facilities, Equipment, Operations and Procedures The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. 5. Trouble with this equipment If trouble is experienced with this equipment, for repair or warranty information, please see the attached warranty, which includes the Servicenter Directory. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. 6. Connection to Party Line Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. 14 Installation Manual 7. Combined Use with Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. When programming emergency numbers and/or making test calls to emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call before hanging up. 2. Perform such activities in the off-peak hours, such as early morning hours or late evenings. WARNING The software contained in the ARS and TRS features to allow user access to the network must be upgraded to recognize newly established network area codes and exchange codes as they are placed into service. Failure to upgrade the on-premise PBXs or peripheral equipment to recognize the new codes as they are established will restrict the customer and users of the PBX from gaining access to the network and to these codes. KEEP THE SOFTWARE UP-TO-DATE WITH THE LATEST DATA. Installation Manual 15 For Cell Station CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void user's authority to operate this device. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Some wireless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the wireless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, move the wireless telephone further away from the TV or VCR. This will often reduce, or eliminate, interference. Operating near 2.4 GHz electrical appliances may cause interference. Move away from the electrical appliances. CAUTION To comply with FCC RF exposure requirements in uncontrolled environment:
This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm (8 in) spacing must be provided between antenna and all person's body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Medicalconsult the manufacturer of any personal medical devices, such as pacemakers, to determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates in the frequency range of 2401 MHz to 2480 MHz, and the power output level can range from 0.004 W to 0.4 W.) Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF (radio frequency) energy. 16 Installation Manual Table of Contents 1 System Outline ..................................................................................... 21 1.1 System Highlights .......................................................................................................... 22 System Highlights ............................................................................................................. 22 1.1.1 Basic System Construction ........................................................................................... 26 1.2 Basic Shelf........................................................................................................................ 26 1.2.1 1.2.2 System Connection Diagram ............................................................................................ 27 1.3 Optional Equipment........................................................................................................ 29 1.3.1 Optional Equipment .......................................................................................................... 29 1.4 Specifications ................................................................................................................. 31 1.4.1 General Description .......................................................................................................... 31 1.4.2 Characteristics .................................................................................................................. 33 1.4.3 System Capacity............................................................................................................... 34 2 Activation Key Installation................................................................... 41 Information about the Activation Keys ......................................................................... 42 2.1 Activation Keys.................................................................................................................. 42 2.1.1 Activation Key Card and Key Management System.......................................................... 44 2.1.2 2.1.3 Activation Key File............................................................................................................. 45 3 Installation............................................................................................. 47 Before Installation........................................................................................................... 48 3.1 3.1.1 Before Installation ............................................................................................................. 48 3.2 Installation of the PBX.................................................................................................... 50 3.2.1 Unpacking ......................................................................................................................... 50 3.2.2 Names and Locations ....................................................................................................... 51 3.2.3 Opening/Closing the Front Cover...................................................................................... 52 Installing/Replacing the Power Supply Unit ...................................................................... 54 3.2.4 Frame ground Connection ................................................................................................ 58 3.2.5 3.2.6 Installing/Removing the Optional Service Cards .............................................................. 59 Types of Connectors ......................................................................................................... 64 3.2.7 Attaching a Ferrite Core.................................................................................................... 66 3.2.8 3.2.9 Fastening an Amphenol Connector .................................................................................. 68 3.2.10 Wall Mounting (KX-TDE200)............................................................................................. 70 3.2.11 Wall Mounting (KX-TDE100)............................................................................................. 72 3.2.12 Floor Standing (KX-TDE200 Only).................................................................................... 74 3.2.13 Surge Protector Installation .............................................................................................. 76 3.3 Information about the Main Processing Card .............................................................. 79 3.3.1 IPCMPR Card ................................................................................................................... 79 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) ........................................ 82 3.3.3 RMT Card (KX-TDA0196)................................................................................................. 83 3.4 Information about the Virtual Cards.............................................................................. 84 Virtual Cards ..................................................................................................................... 84 3.4.1 Information about the Physical Trunk Cards................................................................ 85 3.5 3.5.1 LCOT8 Card (KX-TDA0180) and LCOT16 Card (KX-TDA0181)....................................... 85 3.5.2 CID8 Card (KX-TDA0193) ................................................................................................ 87 T1 Card (KX-TDA0187) .................................................................................................... 88 3.5.3 PRI23 Card (KX-TDA0290)............................................................................................... 90 3.5.4 3.5.5 IP-GW4E Card (KX-TDA0484) ......................................................................................... 92 Installation Manual 17 3.5.6 IP-GW16 Card (KX-TDA0490) ..........................................................................................94 3.6 Information about the Physical Extension Cards ........................................................96 3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) ...........................................96 3.6.2 DHLC8 Card (KX-TDA0170) .............................................................................................99 3.6.3 DLC8 Card (KX-TDA0171)..............................................................................................102 3.6.4 DLC16 Card (KX-TDA0172)............................................................................................104 SLC8 Card (KX-TDA0173)..............................................................................................106 3.6.5 EXT-CID Card (KX-TDA0168) .........................................................................................108 3.6.6 3.6.7 SLC16 Card (KX-TDA0174) and MSLC16 Card (KX-TDA0175).....................................109 IP-EXT16 Card (KX-TDA0470) .......................................................................................111 3.6.8 3.7 Information about the Other Physical Cards ..............................................................113 3.7.1 OPB3 Card (KX-TDA0190) .............................................................................................113 3.7.2 DPH4 Card (KX-TDA0161) .............................................................................................114 EIO4 Card (KX-TDA0164)...............................................................................................116 3.7.3 3.7.4 ECHO16 Card (KX-TDA0166) ........................................................................................119 3.7.5 MSG4 Card (KX-TDA0191).............................................................................................120 3.8 Connection of Extensions............................................................................................121 3.8.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) ...........................121 3.8.2 Parallel Connection of the Extensions ............................................................................123 3.8.3 Digital EXtra Device Port (Digital XDP) Connection........................................................126 3.8.4 First Party Call Control CTI Connection..........................................................................128 3.9 Connection of 2.4 GHz Portable Stations ...................................................................129 3.9.1 Overview .........................................................................................................................129 Procedure Overview........................................................................................................131 3.9.2 3.9.3 Site Planning...................................................................................................................133 Before Site Survey ..........................................................................................................137 3.9.4 Site Survey......................................................................................................................141 3.9.5 3.9.6 After Site Survey .............................................................................................................145 3.9.7 Connecting a Cell Station to the PBX .............................................................................146 3.9.8 Wall Mounting .................................................................................................................155 3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays...........159 3.10.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays............159 3.11 Connection of Peripherals ...........................................................................................162 3.11.1 Connection of Peripherals...............................................................................................162 3.12 LAN Connection ............................................................................................................166 3.12.1 LAN Connection..............................................................................................................166 3.13 Power Failure Connections ..........................................................................................167 3.13.1 Power Failure Connections .............................................................................................167 3.14 Starting the PBX............................................................................................................169 3.14.1 Starting the PBX .............................................................................................................169 4 Guide for the KX-TDE Maintenance Console ................................... 171 4.1 Overview ........................................................................................................................172 4.1.1 Overview .........................................................................................................................172 4.2 Connection ....................................................................................................................173 4.2.1 Connection......................................................................................................................173 Installation of the KX-TDE Maintenance Console ......................................................175 4.3 4.3.1 Installing and Starting the KX-TDE Maintenance Console .............................................175 5 Troubleshooting.................................................................................. 179 5.1 Troubleshooting ............................................................................................................180 18 Installation Manual 5.1.1 Installation....................................................................................................................... 180 5.1.2 Connection...................................................................................................................... 183 5.1.3 Operation ........................................................................................................................ 185 5.1.4 Using the Reset Button................................................................................................... 187 5.1.5 Troubleshooting by Error Log.......................................................................................... 188 Index .......................................................................................................... 191 Installation Manual 19 20 Installation Manual Section 1 System Outline This section provides general information on the PBX, including the system capacity and specifications. Installation Manual 21 1.1 System Highlights 1.1 System Highlights 1.1.1 System Highlights IPCMPR Card Features The IPCMPR card (the pre-installed Main Processing card) includes the following features and resources:
VoIP CO Lines/VoIP Extensions The IPCMPR card allows the use of IP CO lines (H.323) and IP telephones (IP-PTs, IP softphones, and SIP Extensions). By connecting a DSP card to the IPCMPR card, these IP CO lines and extensions can be used. It is also possible to increase the number of IP CO lines (max. 32) and extensions (max. 128) through the purchase of activation key cards. LAN Connection The IPCMPR card comes included with a Local Area Network (LAN) port (RJ45 port) allowing for the PBX to be connected to a LAN. Computer Telephony Integration (CTI) Features Connecting a PC to a DPT, or connecting a CTI Server to this PBX, allows functions of the PC, PBX and extensions to be integrated. For example, detailed caller information can be taken from a database and displayed on the PC as a call arrives, or the PC can dial numbers for the extension automatically. Simplified Voice Message (SVM) Features The IPCMPR card comes pre-installed with the SVM feature (2 channels), allowing for simple answering machine services to be supported. Internet Protocol (IP) Telephone Features This PBX supports the following telephone features that use IP:
IP-PT Features This PBX supports the connection of IP-PTs which function almost identically to normal PTs. However, they connect to the PBX over a LAN and make and receive calls using IP. In addition, KX-NT300 series IP-PTs support the following features:
Self Labelling (KX-NT366 only) The LCDs featured next to the 12 flexible buttons of the KX-NT366 can be programmed to display information regarding the setting of the corresponding flexible button. In addition, the flexible buttons can be organized into 4 pages allowing you to assign a total of 4 items to each physical button. Optional Modules
KX-NT307(PSLP1528) Bluetooth Module:
Allows for a Bluetooth wireless headset to be connected to a KX-NT300 series IP-PT. KX-NT303 Add-on 12 Key Module:
Allows for 12 additional flexible buttons to be connected to a KX-NT346 or KX-NT343. KX-NT305 Add-on 60 Key Module:
Allows for 60 additional flexible buttons to be connected to a KX-NT346 or KX-NT343. High Sound Quality 22 Installation Manual 1.1 System Highlights Calls between KX-NT300 series IP-PTs support G.722 CODEC allowing for high sound quality conversations. SIP (Session Initiation Protocol) Extensions This PBX supports the connection of third party SIP supported IP telephones (hardphones and softphones). SIP Extensions make and receive calls using IP. IP Softphones This PBX supports the connection of Panasonic IP softphones, providing IP-PT operations and features using software on a PC. Internet Protocol (IP) Related Features Server Connection This PBX supports the connection to the following servers, allowing for enhanced efficiency and record keeping:
SNMP Server:
Allows for users assigned as SNMP managers to manage and receive PBX system status information, such as local alarm information and general system activity using Simple Network Management Protocol (SNMP). SNTP Server:
Allows for the PBX to automatically receive and update the time setting using Simple Network Time Protocol (SNTP). DHCP Server:
Allows for this PBX to receive IP addresses from a Dynamic Host Configuration Protocol (DHCP) server. Peer-to-peer Connection Intercom calls can be made between peer-to-peer compatible IP extensions allowing for communication without using the PBX's VoIP resources. Networking Features This PBX supports the following networking features:
Voice over Internet Protocol (VoIP) Network The PBX can connect to another PBX via a private IP network. In this case, voice signals are converted into IP packets and sent through this network. Automatic rerouting of VoIP calls to public CO lines is also available, in case of network difficulties. TIE Line Service A TIE line is a privately leased communication line between two or more PBXs, which provides cost effective communications between company members at different locations. Virtual Private Network (VPN) VPN is a service provided by the VPN service provider. It uses an existing public line as if it were a private line. QSIG Network QSIG is a protocol based on ISDN (Q.931) and offers enhanced PBX features in a private network of two or more connected PBXs. Installation Manual 23 1.1 System Highlights External Device Support The following are just a few of the many useful optional devices available to enhance your telephony system:
Portable Station (PS) Features PSs can be connected to this PBX. It is possible to use the PBX features using the PS like a PT. This PBX supports basic CSs (allows up to 4 PSs to be on a call simultaneously) as well as high-density CSs (allows up to 8 PSs to be on a call simultaneously). A PS can also be used in parallel with a wired telephone (Wireless XDP Parallel Mode). In this case, the wired telephone is the main telephone and the PS is the sub telephone. Cellular Phone Features (KX-NCS4910 required) This PBX supports the use of cellular phones destinations with the PBX. In combination with the use of certain features such as Virtual PS, DISA, and XDP Parallel mode, cellular phones can make and receive calls as if they were registered extensions. Phone Assistant (PA) Pro Series This PBX supports KX-TDA Phone Assistant Pro Series applications, a collection of highly-intuitive CTI applications that allow you to use your PC to access a variety of PBX features conveniently and efficiently. PA Pro series applications combine the efficiency and user-friendliness of CTI applications with the convenience of server-based applications, allowing User IDs, passwords and PBX settings to be configured over a web browser. Voice Mail Features This PBX supports Voice Processing Systems (VPS) with DTMF Integration as well as DPT (Digital) Integration, connected locally and over a network. ACD Report Server (KX-NCV200) This PBX supports VPSs with an ACD Report Server. In addition to VPS features, the ACD Report Server provides you with a variety of features, such as monitoring, reporting, call logging features and creating performance graphs, to manage call information efficiently. Other Useful Features Easy Installation and Setup With Physical Cards By simply connecting telephones and outside lines to analog extension and CO line cards you can make and receive calls. For digital CO lines (e.g., T1, etc.), it may be necessary to first make the required settings and restart the PBX. With Virtual Cards By connecting the PBX to the LAN, installing each virtual card and registering the IP telephones through system programming, you can make and receive calls. Enhanced Walking Extension Feature It is possible to use the Walking Extension feature with extensions in Service-in (functions normally) and Service-out (cannot make CO line calls or receive calls) modes, allowing users to use their extensions at home and at work, or for multiple users who work in shifts to use their own extension settings on a single telephone. 24 Installation Manual 1.1 System Highlights Built-in Small Call Centre Features An incoming call distribution (ICD) group can be used as a small call centre with the following features:
Queuing Feature When a preprogrammed number of extensions in an ICD group are busy, additional incoming calls can wait in a queue. While callers are waiting in the queue, they can be sent an outgoing message
(OGM) informing the caller of the current situation, or be redirected to another destination or disconnected depending on the amount of time the caller has been waiting. Log-in/Log-out ICD group members can join (Log-in) or leave (Log-out) their groups manually. After a call is completed, a preprogrammed time period where users will not receive calls can be assigned
(Wrap-up). This gives time for users to make reports about the previous call without be interrupted or allows users to not receive calls while they are taking a break. VIP Call The VIP Call feature is one method of making sure that calls from preferred customers or callers are answered quickly. When using VIP Call mode, ICD groups are assigned a priority, allowing calls in higher-priority groups to be answered before calls in lower-priority groups. Hospitality Features This PBX has several features allowing it to be used effectively and efficiently in a hotel-type environment. These features allow extensions assigned as hotel operators to change and monitor the room status of guest rooms, check or set wake-up calls, and print out records of guest charges. Installation Manual 25 1.2 Basic System Construction 1.2 Basic System Construction 1.2.1 Basic Shelf The basic shelf contains an IPCMPR card for controlling the PBX. To use the system, install a power supply unit (PSU) in the PSU Slot and optional service cards in the basic shelf. KX-TDE100 KX-TDE200 Construction of the Basic Shelf IPCMPR Card Free Slots IPCMPR Card Free Slots PSU Slot PSU Slot KX-TDE100 KX-TDE200 26 Installation Manual 1.2.2 System Connection Diagram CO (Telephone Company) Lines Analog/PRI/T1 Remote PC 1.2 Basic System Construction Private IP Network Pure IP-PBX Router PC IP-PT IP Softphone SIP Extension Fax Machine SLT Wireless Phone APT DSS Console Batteries PC Printer External Sensor/
External Relay Device DPT DSS Console ISDN Telephone CTI Server Doorphone & Door Opener PS CS USB BGM/Music On Hold (MOH) Pager/
Speaker Amplifier KX-T7636/
KX-T7633 PC Voice Processing System KX-T7600 DPT KX-T7600 DPT PC PC Installation Manual 27 1.2 Basic System Construction LCOT4 LCOT16
(KX-TDA0183)
(KX-TDA0181) LCOT8
(KX-TDA0180) CID8
(KX-TDA0193) PRI23
(KX-TDA0290) T1
(KX-TDA0187) IP-GW4E
(KX-TDA0484) IP-GW16
(KX-TDA0490) PSU-S/M/L
(KX-TDA0108/
KX-TDA0104/
KX-TDA0103) MSLC16
(KX-TDA0175) SLC16
(KX-TDA0174) SLC8
(KX-TDA0173) EXT-CID
(KX-TDA0168) DLC16
(KX-TDA0172) DLC8
(KX-TDA0171) DHLC8
(KX-TDA0170) OPB3
(KX-TDA0190) DPH4
(KX-TDA0161) EIO4
(KX-TDA0164) ECHO16
(KX-TDA0166) MSG4
(KX-TDA0191) CSIF4
(KX-TDA0143) CSIF8
(KX-TDA0144) IP-EXT16
(KX-TDA0470) IPCMPR
(Installed by default) RMT
(KX-TDA0196) DSP16
(KX-TDE0110) DSP64
(KX-TDE0111) Virtual Trunk Slot Virtual Extension Slot V-IPGW16 V-IPEXT32 V-SIPEXT32 Mountable Equipment Analog CO Line Telephone Company ISDN PRI Line
(Digital CO Line) T1 Line
(Digital CO Line) Private IP Network Router Uninterruptible Power Supply (UPS) Station Message Detail Recording (SMDR) PC Private IP Network Router 28 Installation Manual SLT Wireless Phone Fax Machine KX-T7636/
KX-T7633 PC KX-T7600 DPT KX-T7600 DPT DPT DSS Console PT-interface CS
(Basic/High-density) PS Voice Processing System APT DPT DSS Console Fax Machine KX-T7636/
KX-T7633 PC SLT Wireless Phone PT-interface CS
(Basic/High-density) PS Voice Processing System KX-T7600 DPT KX-T7600 DPT Doorphone & Door Opener External Sensor/External Relay Device CS PS LAN Radio LAN IP-PT IP Softphone Amplifier Pager/Speaker IP-PT IP Softphone SIP Extension PC CTI Server 1.3 Optional Equipment 1.3.1 Optional Equipment 1.3 Optional Equipment Model No. Model Name Description KX-TDE0110 16-Channel VoIP DSP Card (DSP16) 16-channel digital signal processor card with an SHGW4 activation key and an IPPT8 activation key pre-installed. Compliant with ITU-T G.729a and G.711 CODEC methods. To be mounted on the IPCMPR card. KX-TDE0111 64-Channel VoIP DSP Card (DSP64) 64-channel digital signal processor card with four SHGW4 activation keys and four IPPT8 activation keys pre-installed. Compliant with ITU-T G.729a and G.711 CODEC methods. To be mounted on the IPCMPR card. KX-TDA0103 L-Type Power Supply Unit (PSU-L) Power Supply Unit for the KX-TDE200. Total power output of 279 W. Safety Class 1 compliant. KX-TDA0104 M-Type Power Supply Unit (PSU-M) Power Supply Unit for the KX-TDE100 and KX-
TDE200. Total power output of 140.4 W. Safety Class 1 compliant. KX-TDA0108 S-Type Power Supply Unit (PSU-S) Power Supply Unit for the KX-TDE100. Total power output of 74 W. Safety Class 1 compliant. KX-TDA0143 4 Cell Station Interface Card (CSIF4) 4-port CS interface card for 4 CSs. KX-TDA0144 8 Cell Station Interface Card (CSIF8) 8-port CS interface card for 8 CSs. KX-TDA0161 4-Port Doorphone Card (DPH4) 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. KX-TDA0164 KX-TDA0166 4-Port External Input/Output Card
(EIO4) 4-port external input/output card. To be mounted on the OPB3 card. 16-Channel Echo Canceller Card
(ECHO16) 16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card. KX-TDA0168 Extension Caller ID Card (EXT-CID) Sends Caller ID signals to extension ports. To be KX-TDA0170 8-Port Digital Hybrid Extension Card
(DHLC8) mounted on the SLC8 card only. 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs (Basic/
High-density), with 2 power failure transfer (PFT) ports. KX-TDA0171 8-Port Digital Extension Card (DLC8) 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-
density). KX-TDA0172 16-Port Digital Extension Card
(DLC16) 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-
density). Installation Manual 29 1.3 Optional Equipment Model No. KX-TDA0173 KX-TDA0174 KX-TDA0175 Model Name Description 8-Port Single Line Telephone Extension Card (SLC8) 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. 16-Port Single Line Telephone Extension Card (SLC16) 16-port extension card for SLTs with 4 power failure transfer (PFT) ports. 16-Port Single Line Telephone Extension with Message Lamp Card
(MSLC16) 16-port extension card for SLTs with Message Waiting Lamp control and 4 power failure transfer
(PFT) ports. Maximum power output of 160 V/90 V for Message Waiting Lamp control. 8-port analog CO line card with 2 power failure transfer (PFT) ports. KX-TDA0180 8-Port Analog Trunk Card (LCOT8) KX-TDA0181 16-Port Analog Trunk Card (LCOT16) 16-port analog CO line card with 4 power failure transfer (PFT) ports. KX-TDA0187 T-1 Trunk Card (T1) 1-port T1 CO line card. EIA/TIA standard compliant. KX-TDA0190 Optional 3-Slot Base Card (OPB3) KX-TDA0191 4-Channel Message Card (MSG4) KX-TDA0193 8-Port Caller ID Card (CID8) KX-TDA0196 Remote Card (RMT) KX-TDA0290 PRI Card (PRI23) KX-TDA0470 16-Channel VoIP Extension Card (IP-
EXT16) KX-TDA0484 4-Channel VoIP Gateway Card (IP-
GW4E) KX-TDA0490 16-Channel VoIP Gateway Card (IP-
GW16) Optional 3-slot base card for mounting a maximum of 3 option cards from the following: MSG4, DPH4, or ECHO16 card. 4-channel message card. To be mounted on the OPB3 card. 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the LCOT8/LCOT16 cards. Analog modem card for remote communication with the PBX. ITU-T V.90 support. To be mounted on the IPCMPR card. 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods. 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and G.711 CODEC methods. 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and G.711 CODEC methods. Note For the maximum number of optional service cards that can be installed in the PBX, refer to "1.4.3 System Capacity". 30 Installation Manual 1.4 Specifications 1.4 Specifications 1.4.1 General Description Control Bus Communication Bus Switching Power Input PSU-S PSU-M PSU-L Maximum Power Failure Tolerance*1 Original bus (16-bit, 8 MHz, 10 megabytes per second) H.100 bus conformity (1024 time slots) Non-blocking 100 V AC to 130 V AC; 1.4 A/200 V AC to 240 V AC; 0.8 A;
50 Hz/60 Hz 100 V AC to 130 V AC; 2.5 A/200 V AC to 240 V AC; 1.4 A;
50 Hz/60 Hz 100 V AC to 130 V AC; 5.1 A/200 V AC to 240 V AC; 2.55 A;
50 Hz/60 Hz
+36 V DC (+12 V DC 3, recommended maximum capacity is 28 Ah) Maximum Power Failure Tolerance 300 ms (without using backup batteries) Memory Backup Duration 7 years Dialing CO Line Extension Mode Conversion Ring Frequency Central Office Loop Limit Operating Environment Temperature Humidity Conference Call CO Line Music on Hold (MOH) Paging Internal External Dial Pulse (DP) 10 pps, 20 pps Tone (DTMF) Dialing Dial Pulse (DP) 10 pps, 20 pps Tone (DTMF) Dialing DP-DTMF, DTMF-DP 20 Hz/25 Hz (selectable) 1600 maximum 0 C to 40 C (32 F to 104 F) 10 % to 90 % (non-condensing) From 10 3-party conference call to 4 8-party conference call 2 ports (Level Control: -11 dB to +11 dB in 1 dB steps) MOH1: External Music Source port MOH2: Selectable Internal/External Music Source port Level Control: -15 dB to +6 dB in 3 dB steps 2 ports (Volume Control: -15 dB to +15 dB in 1 dB steps) Serial Interface Port RS-232C 1 (maximum 115.2 kbps) RJ45 2 Installation Manual 31 1.4 Specifications Extension Connection Cable SLT DPT APT PT-interface CS (Basic/
High-density) DSS Console and Add-on Key Module 1-pair wire (T, R) 1-pair wire (D1, D2) or 2-pair wire (T, R, D1, D2) 2-pair wire (T, R, D1, D2) 1-pair wire (D1, D2) 1-pair wire (D1, D2) Dimension KX-TDE100 Weight (when fully mounted) KX-TDE200 KX-TDE100 KX-TDE200 334 mm (W) 390 mm (H) 272 mm (D)
(13-1/3 in 15-3/5 in 10-3/4 in) 430 mm (W) 415 mm (H) 276 mm (D)
(17-1/5 in 16-3/5 in 10-7/8 in) Under 12 kg (26.4 lb) Under 16 kg (35.2 lb)
*1 If tolerance may be exceeded, an Uninterruptible Power Supply (UPS) is recommended. 32 Installation Manual 1.4 Specifications 1.4.2 Characteristics Terminal Equipment Loop Limit Minimum Leakage Resistance Maximum Number of Extension Instruments per Line PT: KX-T7600 series DPT: 90 ; all other DPTs/APTs: 40 SLT: 600 including set Doorphone: 20 CS: 130 ; PT-interface CS (Basic/High-density): 65
15 000 minimum 1 for PT or SLT 2 by Parallel or eXtra Device Port connection of an APT/DPT and an SLT 3 by Digital eXtra Device Port connection of 2 DPTs and an SLT Ring Voltage Central Office Loop Limit Hookswitch Flash Timing Range 75 Vrms at 20 Hz/25 Hz depending on the Ringing Load 1600 maximum 24 ms to 2032 ms Door Opener Current Limit 24 V DC/30 V AC, 1 A maximum External Relay Current Limit 24 V DC/30 V AC, 1 A maximum External Sensor Current Limit Paging Terminal Impedance MOH (Music on Hold) Terminal Impedance Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card. For the connection diagram, refer to
"3.7.3 EIO4 Card (KX-TDA0164)". The PBX detects input from the sensor when the signal is under 100 . 600 10 000 Installation Manual 33 1.4 Specifications 1.4.3 System Capacity Type and Maximum Number of Slots The PBX supports the following type and number of slots. Slot Type Maximum Number KX-TDE100 KX-TDE200 IPCMPR Card Slot Free Slot Virtual Slot Virtual CO Line Slot Virtual Extension Slot 1 6 4 4 1 11 4 4 IPCMPR Card Slot and Free Slots KX-TDE100 KX-TDE200 IPCMPR Card Slot IPCMPR Card Slot Free Slots 1 to 6 (from the left) Free Slots 1 to 11 (from the left) Virtual Slots of the IPCMPR Card Virtual Virtual CO Line Slots Extension Slots IPCMPR Card Virtual Slots 34 Installation Manual 1.4 Specifications Maximum Optional Service Cards The following number of cards can be installed in the Free Slots or Virtual Slots of the PBX. Notes
When the PBX starts up with an invalid configuration, some cards will be ignored. Any card that exceeds the capacity of the PBX will be ignored. Cards Installed in Free Slots or Virtual Slots Card Type IPCMPR CO Line Card Virtual CO Line Card V-IPGW16 Physical CO Line Card LCOT8 LCOT16 T1 PRI23 IP-GW4E IP-GW16 Extension Card Virtual Extension Card V-IPEXT32 V-SIPEXT32 Physical Extension Card DHLC8 DLC8 DLC16 SLC8 SLC16 MSLC16 IP-EXT16 CSIF4 CSIF8 OPB3 Total
*1 Maximum Number KX-TDE100 KX-TDE200 1 8 4 2 1 8 4 2 Total 6
*1 Total 8
*2 6 4 4 8 4 2 4 8 4 4 8 4 2 4 Total 6 Total 8 6 4 4 14 8 4 4 16 When installing T1 and PRI23 cards, make sure that the number of these cards 2 + the number of the other cards (including IP-GW4E cards) does not exceed 8. One T1 or PRI23 card counts as 2 cards.
*2 Installation Manual 35 1.4 Specifications Cards Mounted on Other Optional Service Cards Card Type Maximum Number KX-TDE100 KX-TDE200 DSP16 DSP64 RMT EXT-CID DPH4 ECHO16 MSG4 EIO4 1 1 6 4 2*1 4 4 1 1 8 4 2*1 4 4 Mounted on IPCMPR Card SLC8 Card OPB3 Card
*1 Only 1 ECHO16 card can be mounted on each OPB3 card. Maximum CO Line and Extension The PBX supports the following number of CO lines and extensions. Type KX-TDE100 KX-TDE200 Total Number of CO Line CO Line (Physical CO Line Card) CO Line (Virtual CO Line Card) Total Number of Extension Extension (Physical Extension Card) Extension (Virtual Extension Card) IP-PT and IP Softphone SIP Extension 128 120 32 256 160 128 64 128 128 128 32 256 256 128 64 128 36 Installation Manual Maximum Terminal Equipment The following shows the number of each terminal equipment type supported by the PBX. Terminal Equipment Type KX-TDE100 KX-TDE200 1.4 Specifications Telephone SLT KX-T7600 series DPT Other DPT APT IP-PT IP-PT*1 (supported by IP-EXT16 card) IP-PT*2 (supported by IPCMPR card) SIP Extension DSS console Basic CS High-density CS PS Voice Processing System (VPS) Doorphone Door Opener External Sensor External Relay 256 96 128 32 24 160 96 64 128 8 32 16 128 2 16 16 16 16
*1 KX-NT136 and KX-NT265
*2 KX-NT300 series and KX-NT265 (software version 2.00 or later only) 256 128 256 128 64 160 128 64 128 8 32 16 128 2 16 16 16 16 Installation Manual 37 1.4 Specifications Note for KX-NT265 IP-PT users The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the version, follow the procedure below:
While starting up PROGRAM SP-PHONE SP-PHONE
"AP Version". Select
"Maintenance". Select
"Version display". SP-PHONE Software version is displayed. To exit the programming mode HOLD HOLD HOLD HOLD Power Supply Unit Selection The PBX needs a power supply unit (PSU) suitable for its configuration. Calculate the load figure from the type and number of items of equipment to be connected, and determine the type of PSU that will be required. Load Figure Calculation PT Extension Card*1 Basic CS (1 unit) High-density CS (1 unit) VPS (1 port) Equipment Type Load Figure KX-T7600 series DPT/KX-T7600 series DSS console Other DPT/Other DSS console APT IP-PT SIP Extension DHLC8 SLC8 SLC16 MSLC16 1 4 4 0 0 8 8 16 16 4 8 1
*1 Only the extension cards that can support SLTs count for the load figures. 38 Installation Manual 1.4 Specifications PSU Capacity Each PSU supports a different load figure. PSU Type Maximum Load Figure PSU-S (for KX-TDE100 only) PSU-M PSU-L (for KX-TDE200 only) Calculation Example (KX-TDE200) 64 128 512 Equipment Type Load Figure KX-T7600 series DPT Other DPT SLC16 MSLC16 VPS Total 48 units 2 units 1 card 1 card 8 ports 48 8 16 16 8 96 The total load figure is 96. As this is between 64 and 128, you should install the PSU-M. But if you expect expansion in the future, it may be better to install the PSU-L. There is no harm in installing a PSU that is larger than is required for the current configuration. Installation Manual 39 1.4 Specifications 40 Installation Manual Section 2 Activation Key Installation This section describes information on activation keys, including how to obtain an activation key and install it in the SD Memory Card. Installation Manual 41 2.1 Information about the Activation Keys 2.1 Information about the Activation Keys 2.1.1 Activation Keys To use IP CO lines and IP telephones on a private IP network using the IPCMPR card or to upgrade the software for enhanced features, you need the appropriate activation keys. Type and Maximum Number of Activation Keys The PBX supports the following type and number of activation keys:
Activation Key Type Description Maximum Number Supported IP CO Lines/IP Telephones SHGW4 IPPT8 IPPTS8 SPE16 UCAV2 Allows the use of 4 IP CO lines via a V-IPGW16 card. Allows the use of 8 IP-PTs via a V-
IPEXT32 card. Allows the use of 8 IP-PTs/IP softphones via a V-IPEXT32 card. Allows the use of 16 SIP Extensions via a V-SIPEXT32 card. Upgrades software to use enhanced features. 8 8 8 1 32 IP CO lines 64 IP-PTs/IP softphones 128 SIP Extensions
Pre-installed Activation Keys in the DSP16/DSP64 The following type and number of activation keys are pre-installed on the DSP16/DSP64 card:
Card Type Activation Key Supported IP CO Lines/IP-PTs DSP16 DSP64 SHGW4 IPPT8 SHGW4 IPPT8 1 1 4 4 4 IP CO lines 8 IP-PTs 16 IP CO lines 32 IP-PTs Depending on the number of IP CO lines and IP-PTs to be used, you need to select either the DSP16 or DSP64 card. 42 Installation Manual 2.1 Information about the Activation Keys Additional Activation Keys in the SD Memory Card (Activation Key Files) In addition to the pre-installed activation keys on the DSP16/DSP64 card, the following type and number of activation keys are installed in the SD Memory Card:
Activation Key Type Maximum Number Supported IP CO Lines/IP Telephones with DSP16 with DSP64 with DSP16 with DSP64 SHGW4 IPPT8 IPPTS8 SPE16 UCAV2 7 7 4 4 28 IP CO lines 16 IP CO lines 56 IP-PTs/IP softphones 32 IP-PTs/IP softphones 8 1 128 SIP Extensions
If the pre-installed activation keys in the DSP card are not enough for the desired configuration or if you wish to use enhanced features, it is necessary to obtain additional activation keys in the form of activation key files and install them in the SD Memory Card. For information about how to obtain the additional activation keys, refer to "2.1.2 Activation Key Card and Key Management System". For information about how to install the activation key files in the SD Memory Card, refer to "2.1.3 Activation Key File". Activation Key Installation Example The following shows an example of when using 32 IP CO lines, 32 IP-PTs, 32 IP softphones, and 64 SIP Extensions on a private IP network using the IPCMPR card. IPCMPR Card Virtual CO Line Virtual Extension Slots Slots SD Memory Card SHGW4 SPE16 16 IP CO lines IPPTS8 DSP64 Card SHGW4 16 IP CO lines IPPT8 64 SIP Extensions 32 IP softphones 32 IP-PTs Total 32 IP CO lines Total 32 IP-PTs 32 IP softphones 64 SIP Extensions Virtual Slots Installation Manual 43 2.1 Information about the Activation Keys 2.1.2 Activation Key Card and Key Management System To obtain additional activation keys, you need to purchase the appropriate activation key cards and access the Key Management System. You can download the activation keys as an activation key file from the Key Management System. To download the activation keys, enter the MPR ID number shown on the IPCMPR card in the PBX, and activation key number and registration ID provided on each activation key card. The following activation key cards are available:
Model No. Card Name Description KX-NCS4104 4-Channel IP Trunk Activation Key KX-NCS4208 8-Channel IP Softphone/IP Proprietary Telephone Activation Key Provides the activation key number and registration ID to download the SHGW4 activation key. Provides the activation key number and registration ID to download the IPPTS8 activation key. KX-NCS4508 8-Channel IP Proprietary Telephone Activation Key Provides the activation key number and registration ID to download the IPPT8 activation key. KX-NCS4716 16-Channel SIP Extension Activation Key KX-NCS4910 Activation Key for Software Upgrade to Enhanced Version Provides the activation key number and registration ID to download the SPE16 activation key. Provides the activation key number and registration ID to download the UCAV2 activation key. Notes
You can only download the activation key file once using the activation key number and registration ID provided on the activation key card. Up to 8 activation keys can be downloaded as one activation key file. It is possible to send the activation key file to a specified e-mail address at the same time as downloading it to a PC.
Make sure to backup the downloaded activation key files on your PC.
In the event of a system malfunction, you need a temporary activation key for maintenance purposes. The temporary activation key can be downloaded from the Key Management System in the same way as downloading activation key files. 44 Installation Manual 2.1 Information about the Activation Keys 2.1.3 Activation Key File The corresponding number of IP CO lines and IP telephones or enhanced features can be activated by installing the downloaded activation key file(s) in the SD Memory Card of the IPCMPR card using the KX-
TDE Maintenance Console. Installing the Activation Key File in the SD Memory Card Make sure to install the KX-TDE Maintenance Console on the PC in advance, and connect the PC to the PBX. For details about the KX-TDE Maintenance Console, refer to "Guide for the KX-TDE Maintenance Console". 1. Start the KX-TDE Maintenance Console from the Start menu on the PC. 2. From the Utility menu, select File Transfer PC to PBX (SD Card). A dialogue box will be displayed. 3. Select the file to upload. A window showing the upload progress will be displayed. While transferring files to the SD memory card, the PBX automatically renames them according to the header information. A message will be displayed when the transfer is complete. 4. Click OK. Note It is necessary to restart the PBX to activate the UCAV2 activation key after performing the procedure above. To restart the PBX, refer to "5.1.4 Using the Reset Button". CAUTION The activation key file can only be installed in the PBX with the MPR ID number entered when the activation key file was downloaded. The activation key file cannot be reissued unless the IPCMPR card crashes. Installation Manual 45 2.1 Information about the Activation Keys 46 Installation Manual Section 3 Installation This section describes the procedures to install the PBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included. Installation Manual 47 3.1 Before Installation 3.1 Before Installation 3.1.1 Before Installation Please read the following notes concerning installation and connection before installing the PBX and terminal equipment. Be sure to comply with all applicable laws, regulations, and guidelines. Safety Installation Instructions When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. 5. Anti-static precautions should be taken during installation. Installation Precautions In direct sunlight and hot, cold, or humid places. (Temperature range: 0 This set is made for wall mounting (KX-TDE100/KX-TDE200) or floor standing (KX-TDE200 only), and should be installed in a location where it is accessible for inspections and maintenance. To prevent malfunction, noise, or discoloration, avoid installing the system in the following locations:
1. C 2. Areas where sulfuric gases may be present, such as near thermal springs. 3. Areas where shocks or vibrations are frequent or strong. 4. High-dust areas, or places the system may come into contact with water or oil. 5. Near devices that generate high frequencies, such as sewing machines or electric welders. 6. On or near computers, telexes, or other office equipment, as well as microwave ovens or air to 40
) C conditioners. (It is preferable not to install the system in the same room as the above equipment.) 7. Within 1.8 m (6 ft) of radios and televisions. (Both the PBX and PTs should be at least 1.8 m (6 ft) away from such devices). 8. Locations where other objects will obstruct the area around the PBX. Be especially careful to leave at least 20 cm (8 in) of space above and 10 cm (4 in) to the sides of the PBX for ventilation. 9. Do not block the openings of the PBX. 10. Do not stack up the optional service cards. Wiring Precautions Be sure to follow these instructions when wiring the unit:
1. Do not run unshielded telephone cables near AC power cables, computer cables, AC power sources, etc. When running cables near other noise-generating devices or cables, use shielded telephone cables or shield the telephone cables with metal tubing. If cables are run on the floor, use protectors to prevent the cables from being stepped on. Avoid running cables under carpets. 2. 48 Installation Manual 3.1 Before Installation 3. Avoid using the same AC outlet for computers, telexes, and other office equipment, as noise generated by such equipment may hamper system performance or interrupt the system. 4. Use 2-pair telephone cables when connecting PTs. Use 1-pair telephone cables when connecting SLTs, data terminals, answering machines, computers, Voice Processing Systems, etc. 5. Unplug the system from its power source when wiring, and plug the system back in only after all wiring is completed. 6. Mis-wiring may cause the PBX to operate improperly. Refer to Section 2 "Installation" when wiring the 7. system. If an extension does not operate properly, disconnect the telephone from the extension line and connect it again, or turn off the PBX using the power switch, then turn it on again. 8. For safety purposes this unit is equipped with a grounded plug. If you do not have a grounded outlet, please have one installed. Do not bypass this safety feature by tampering with the plug. 9. Use twisted pair cable for CO line connection. 10. CO Lines should be installed with surge protectors. For details, refer to "3.2.13 Surge Protector Installation". 11. To assure good quality telephone connection, it is recommended new and modifications to existing installation of customer premise wiring shall use solid twisted pair copper conductors with minimum 24 gauge that comply with the electrical specifications for Category 3 wiring as detailed in ANSI/EIA/TIA-
570A Building Wiring Standards. Installation Manual 49 3.2 Installation of the PBX 3.2 Installation of the PBX 3.2.1 Unpacking Unpack the box and check the items below:
Main Unit Ferrite Core (for the IPCMPR card) Metal Bracket Screw A Screw B (Black) Anchor Plug Mini Plug (for pager and music source) SD Memory Card KX-TDE100 KX-TDE200 1 2 1 3 2 3 4 1 1 2 1 4 6 4 4 1 50 Installation Manual 3.2 Installation of the PBX 3.2.2 Names and Locations Inside View KX-TDE100 KX-TDE200 D C B A D C B A E F G H E I H A. RUN Indicator B. ALARM Indicator C. RJ45 Ports D. RS-232C Port E. PSU Slot F. Null Slot (not available for any optional service card) G. Free Slots 1 to 6 (from the left) H. I. IPCMPR Card Slot Free Slots 1 to 11 (from the left) Installation Manual 51 3.2 Installation of the PBX 3.2.3 Opening/Closing the Front Cover Opening the Front Cover 1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Screw Cover 2. Turn the screw anticlockwise to loosen. 3. Slide the front cover to the right until it stops, then lift the front cover. 52 Installation Manual Closing the Front Cover 1. Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf). Then slide the front cover to the left until it locks. 3.2 Installation of the PBX 2. Turn the screw clockwise to tighten. 3. Secure the screw cover. 2 1 Notes
For safety reasons, close the front cover and tighten the screw before operating the PBX. Do not forget to tighten the screw before securing the screw cover. Installation Manual 53 3.2 Installation of the PBX 3.2.4 Installing/Replacing the Power Supply Unit Function PSU Type Lower/Upper Input Voltage Range Current Input Frequency PSU-S
(for KX-TDE100) PSU-M
(for KX-TDE100/KX-
TDE200) PSU-L
(for KX-TDE200) Lower: 100 V AC to 130 V AC Upper: 200 V AC to 240 V AC Lower: 100 V AC to 130 V AC Upper: 200 V AC to 240 V AC Lower: 100 V AC to 130 V AC Upper: 200 V AC to 240 V AC 1.4 A 0.8 A 2.5 A 1.4 A 5.1 A 2.55 A PSU-S PSU-M/PSU-L 50 Hz or 60 Hz Power Switch Ground Terminal AC Inlet Ground Terminal Power Switch AC Inlet Accessories and User-supplied Items Accessories (included): Screws 4, AC power cord 1 User-supplied (not included): Grounding wire Notes
For details about frame ground connection, refer to "3.2.5 Frame ground Connection". Safety Instructions Each PSU complies with Safety Class 1 of IEC60950, EN60950, UL60950, CAN/CSA-C22.2 No.60950, and AS/NZS60950; therefore a protective ground connection exists between the mains outlet ground and the PSU case. To ensure the PBX chassis is safely grounded, it is essential that the PSU case be securely fastened to the PBX chassis with the 4 screws provided with each PSU. When installing or replacing a PSU, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Never install or replace a PSU during a lightning storm. 2. Never install or replace a PSU in wet locations. 3. Never install or replace a PSU unless at least 20 s has elapsed after the AC supply is disconnected. 54 Installation Manual 3.2 Installation of the PBX 4. To protect the back board from static electricity, do not touch parts on the back board in the main unit and PSU. To discharge static electricity, touch ground or wear a grounding strap. The following procedures are for installing or replacing a PSU only. Do not replace or remove the PSU for any other purpose. Installing the Power Supply Unit 1. Insert the PSU along the guide rails. CAUTION For safety reasons, do not touch parts in the PSU. Guide Rail Installation Manual 55 3.2 Installation of the PBX 2. Push the release lever in the direction of the arrow, so that the PSU engages securely with the connector on the back board. Back Board Release Lever 3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Screws 3 2 4 1 Replacing the Power Supply Unit 1. Unplug the AC power cord. 56 Installation Manual 3.2 Installation of the PBX 2. Turn the 4 screws anticlockwise to loosen them. Screws 3. Pull the release lever in the direction of the arrow to disconnect the PSU from the back board. Release Lever Back Board 4. Replace the PSU. New PSU Current PSU 5. Follow the steps in "Installing the Power Supply Unit". Installation Manual 57 3.2 Installation of the PBX 3.2.5 Frame ground Connection IMPORTANT Connect the frame of the PBX to ground. 1. Loosen the screw. 2. Insert a grounding wire (user-
supplied)*. 3. Tighten the screw. 4. Connect the grounding wire to ground. Screw Grounding wire To earth
* For grounding wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor must be more than 0.75 mm2 or 18 AWG.
Be sure to comply with applicable local regulations (e.g., laws, guidelines). Proper grounding (connection to ground) is very important to protect the PBX from the bad effects of external noise or to reduce the risk to the user of electrocution in the case of a lightning strike. The grounding wire of the AC cable has an effect against external noise and lightning strikes, but it may not be enough to protect the PBX. A permanent connection between ground and the ground terminal of the PBX must be made. In most of the continental United States, the ground provided by the "Third wire ground" at the commercial power outlet will be satisfactory. However, in a small percentage of cases this ground may be installed incorrectly. Therefore, the following test procedure should be performed. Test Procedure 1. Obtain a suitable voltmeter and set it for a possible reading of up to 250 V AC. 2. Connect the meter probes between the 2 main AC voltage points on the wall outlet. The reading obtained should be 108 V AC to 132 V AC. 3. Move one of the meter probes to the 3rd prong terminal (GND). 4. 5. Either the same reading or a reading of 0 volt should be obtained. If a reading of 0 volt at one terminal and a reading of 108 V AC to 132 V AC at the other terminal is not obtained, the outlet is not properly grounded. This condition should be corrected by a qualified electrician (per article 250 of the National Electrical Code). If a reading of 0 volt at one terminal and a reading of 108 V AC to 132 V AC at the other terminal is obtained, then set the meter to the "OHMS/RX1" scale, place one probe at the GND Terminal and the other probe at the terminal which gave a reading of 0 volt. A reading of less than 1 ohm should be obtained. If the reading is not obtained, the outlet is not adequately grounded. See qualified electrician. 58 Installation Manual 3.2 Installation of the PBX 3.2.6 Installing/Removing the Optional Service Cards CAUTION To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional service cards. To discharge static electricity, touch ground or wear a grounding strap. Note The optional service cards can be installed or removed while the DC power is supplied. However, when installing or removing the IPCMPR card, the DC power supply must be turned off. Installing Optional Service Cards 1. Insert the card along the guide rails. Guide Rail Installation Manual 59 3.2 Installation of the PBX 2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with the connector on the back board. Back Board Release Lever 3. Turn the 2 screws clockwise to fix the card in place. Screws Note Make sure the screws are tightened to ground the card securely. 60 Installation Manual 3.2 Installation of the PBX Covering the Blank Slots Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. CAUTION Failure to install the Blank Slot Cover may cause electromagnetic interference. Installation Manual 61 3.2 Installation of the PBX Handling of the Cables When cables are connected to the PBX, run the cables to either the right or the left and then towards the back of the shelf as shown below. 2 1 3 4 Note For safety reasons, do not stretch, bend, or pinch the AC power cord. 62 Installation Manual Removing the Optional Service Cards 1. Turn the 2 screws anticlockwise to loosen them. 3.2 Installation of the PBX Screws 2. Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the card from the shelf to remove it. Back Board Release Lever Installation Manual 63 3.2 Installation of the PBX 3.2.7 Types of Connectors Connector Type Pin Number Used for DHLC8 (KX-TDA0170) SLC8 (KX-TDA0173) SLC16 (KX-TDA0174)
MSLC16 (KX-TDA0175)
LCOT8 (KX-TDA0180) LCOT16 (KX-TDA0181)
IPCMPR CSIF4 (KX-TDA0143) CSIF8 (KX-TDA0144) T1 (KX-TDA0187) PRI23 (KX-TDA0290) IP-EXT16 (KX-TDA0470) IP-GW4E (KX-TDA0484) IP-GW16 (KX-TDA0490) DHLC8 (KX-TDA0170) DLC8 (KX-TDA0171) DLC16 (KX-TDA0172) SLC8 (KX-TDA0173) SLC16 (KX-TDA0174)
MSLC16 (KX-TDA0175)
LCOT8 (KX-TDA0180) LCOT16 (KX-TDA0181)
DPH4 (KX-TDA0161) EIO4 (KX-TDA0164)
Basic Shelf RJ11
(Twisted pair cable) RJ45
(Twisted pair cable) Amphenol Type A Type B
(Shielded twisted pair cable) 10-pin Terminal Block 8-pin Terminal Block RS-232C 64 Installation Manual 1 4 8 1 50 25 26 1 1 1 10 8 6 1 9 5 3.2 Installation of the PBX Connector Type Pin Number Used for Mini Plug
IPCMPR 2 4 Installation Manual 65 3.2 Installation of the PBX 3.2.8 Attaching a Ferrite Core A ferrite core must be attached when:
an RJ45 connector is connected to an IPCMPR, IP-GW16 or IP-EXT16 cards, or an Amphenol connector is connected to an extension card. Attaching to an RJ45 Connector For the IPCMPR Card Wrap the cable once around the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm (1-3/16 in) away from the connector. The ferrite core is included with the PBX. 3 cm
(1-3/16 in) For IP-GW16/IP-EXT16 Cards Wrap the cable once around the ferrite core, then close the case of the ferrite core. Attach the ferrite core 5 cm (1-15/16 in) away from the connector. The ferrite core is included with the card. 5 cm
(1-15/16 in) 66 Installation Manual 3.2 Installation of the PBX Attaching to an Amphenol Connector For Extension Cards Pass the cable through the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm
(1-3/16 in) away from the connector. The ferrite core is included with the card. 3 cm
(1-3/16 in) If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core. Installation Manual 67 3.2 Installation of the PBX 3.2.9 Fastening an Amphenol Connector An Amphenol 57JE-type connector is used on some of the optional service cards. To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro tape to fix the lower part of the connector. Type A (Spring Latch + Velcro Tape) Type B (Screw + Velcro Tape) Velcro Tape Velcro Tape Spring Latch 1 Remove the screw on the optional service card. 2 1 Insert the screw (included with the Amphenol or optional service card). 2 Spring Latch 1 2 68 Installation Manual Amphenol Connector Pin Assignment Chart Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol connector. For more details, refer to the appropriate section in "3.5 Information about the Physical Trunk Cards" and "3.6 Information about the Physical Extension Cards". 3.2 Installation of the PBX LCOT8 LCOT16 DHLC8 DLC8 DLC16 MSLC16 SLC16 D2A D1A D2B D1B D2C D1C D2D D1D D2E D1E D2F D1F D2G D1G D2H D1H D2I D1I D2J D1J D2K D1K D2L D1L D2M D1M D2N D1N D2O D1O D2P D1P RA TA RB TB RC TC RD TD RE TE RF TF RG TG RH TH RI TI RJ TJ RK TK RL TL RM TM RN TN RO TO RP TP RA TA RB TB RC TC RD TD RE TE RF TF RG TG RH TH RI TI RJ TJ RK TK RL TL RM TM RN TN RO TO RP TP RA TA RB TB RC TC RD TD RE TE RF TF RG TG RH TH RA TA RB TB RC TC RD TD RE TE RF TF RG TG RH TH RI TI RJ TJ RK TK RL TL RM TM RN TN RO TO RP TP RA TA D2A D1A RB TB D2B D1B RC TC D2C D1C RD TD D2D D1D RE TE D2E D1E RF TF D2F D1F RG TG D2G D1G RH TH D2H D1H D2A D1A D2B D1B D2C D1C D2D D1D D2E D1E D2F D1F D2G D1G D2H D1H SLC8 RA TA RB TB RC TC RD TD RE TE RF TF RG TG RH TH Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Installation Manual 69 3.2 Installation of the PBX 3.2.10 Wall Mounting (KX-TDE200) CAUTION
Make sure that the wall the shelf will be attached to is capable of supporting at least 4 times the
weight of the shelf. Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall. Notes
Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the shelf.
Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on the back of the shelf will not be blocked.
Make sure that the surface behind the shelf is not made of wood.
Be careful not to drop the shelf. 1. Install 4 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 4 screws (A). Anchor Plug Metal Bracket Wall Hammer Anchor Plug 8 mm
(5/16 in) 30 mm
(1-3/16 in) Screw (A) Screw (A) Metal Bracket 70 Installation Manual 2. Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf. 3.2 Installation of the PBX TOP Screw (B) Installation Manual 71 3.2 Installation of the PBX 3.2.11 Wall Mounting (KX-TDE100) CAUTION
Make sure that the wall the shelf will be attached to is capable of supporting at least 4 times the
weight of the shelf. Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall. Notes
Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the shelf.
Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on the back of the shelf will not be blocked.
Make sure that the surface behind the shelf is not made of wood.
Be careful not to drop the shelf. 1. Install 3 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 3 screws (A). Anchor Plug Wall Metal Bracket TOP Screw (A) TOP Hammer Anchor Plug 8 mm
(5/16 in) 30 mm
(1-3/16 in) Screw (A) Metal Bracket 72 Installation Manual 2. Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf. 3.2 Installation of the PBX TOP Screw (B) Installation Manual 73 3.2 Installation of the PBX 3.2.12 Floor Standing (KX-TDE200 Only) Notes
Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the shelf.
Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on the back of the shelf will not be blocked.
Make sure that the surface behind the shelf is not made of wood.
Be careful not to drop the shelf. 1. Install 4 anchor plugs in the floor, using the metal bracket as a template. Fix the metal bracket with 4 screws (A). Screw (A) Metal Bracket TOP Anchor Plug Floor Screw (A) Metal Bracket Hammer Anchor Plug 30 mm
(1-3/16 in) 8 mm
(5/16 in) 2. Remove the front cover of the shelf (refer to "3.2.3 Opening/Closing the Front Cover"). 74 Installation Manual 3. Lift the shelf, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws (B). 3.2 Installation of the PBX 1 2 TOP FRONT Screws (B) Metal Bracket 4. Fix the front cover on the shelf (refer to "3.2.3 Opening/Closing the Front Cover"). Installation Manual 75 3.2 Installation of the PBX 3.2.13 Surge Protector Installation Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m (33 ft) above ground, or if a telephone line comes into contact with a power line. A surge protector is a device that is connected to a CO line to prevent potentially dangerous electrical surges from entering the building via the CO line and damaging the PBX and connected equipment. Surge arrestor type: 3-electrode arrestor DC spark-over voltage: 230 V To protect the system from electrical surges, we strongly recommend connecting the system to a surge protector that meets the following specifications:
Maximum peak current: at least 10 kA Additionally, proper grounding is very important for the protection of the system (refer to "3.2.5 Frame ground Connection"). Many countries/areas have regulations requiring surge protection. Be sure to comply with all applicable laws, regulations, and guidelines. Installation CO Line CO Line CO Line Surge Protector Terminal Board Extn. PBX Extn. SLT PT PT-interface CS CS Frame Ground Ground Extn.: Extension line 76 Installation Manual 3.2 Installation of the PBX
(Another Building) SLT PT PT-interface CS CS Extn. Surge Protector Outside Installation CO Line
(Main Building) Surge Protector CO Line Terminal Board PBX Extn. Extn. Extn. SLT PT PT-interface CS CS Ground Extn.: Extension Line If you install an extension outside of the building, the following precautions are recommended:
Install the extension wire underground. a. b. Use a conduit to protect the wire. Note The surge protector for an extension and CS is different from that for CO lines. Installation of a ground Rod Surge Protector CO Line Grounding Wire PBX
(Underground) Ground Rod Installation Manual 77 3.2 Installation of the PBX 1. Connect the ground rod to the surge protector using a grounding wire with a cross-sectional area of at least 1.3 mm2. 2. Bury the ground rod near the protector. The grounding wire should be as short as possible. 3. The grounding wire should run straight to the ground rod. Do not run the wire around other objects. 4. Bury the ground rod at least 50 cm (20 in) underground. Notes
The above figures are recommendations only. The length of ground rod and the required depth depend on the composition of the soil. 78 Installation Manual 3.3 Information about the Main Processing Card 3.3 Information about the Main Processing Card 3.3.1 IPCMPR Card Function The IPCMPR card is the pre-installed main processing card with built-in SVM feature (2-channel). The Virtual Cards (CO line/extension) can be installed in Virtual Slots of the IPCMPR card and can be activated with the activation keys. Also, the IPCMPR supports LAN connection so that IP telephones (IP-PTs, IP softphones, SIP Extensions) and PCs can be connected on a private IP network. Mountable Cards
Either one of the DSP16 or DSP64 cards (refer to "3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111)" ) RMT card (refer to "3.3.3 RMT Card (KX-TDA0196)" ) LEDs SD Memory Card Slot Cover Reset Button System Initialize Switch RJ45
(10BASE-T/100BASE-TX Full Duplex) BGM/MOH Pager MPR ID Number RJ45 (for PC Maintenance) To PC To LAN LEDs RJ45 (for LAN Connection) 1 2 SD CARD SD Memory Card 3 SD CARD 4 SD CARD 5 Installation Manual 79 3.3 Information about the Main Processing Card Notes
When connecting the RJ45 connector, attach the ferrite core included with the PBX. Refer to "3.2.8 The maximum length of the cable to be connected to the IPCMPR card is 100 m (328 ft). Attaching a Ferrite Core". For details about Virtual Slots, refer to "1.4.3 System Capacity". For details about the activation keys, refer to "2.1 Information about the Activation Keys". For details about connecting to a LAN, refer to "3.12 LAN Connection". For details about connecting peripherals, refer to "3.11.1 Connection of Peripherals". For details about System Initialize Switch, refer to "3.14.1 Starting the PBX". For details about Reset Button, refer to "5.1.4 Using the Reset Button".
WARNING A LITHIUM BATTERY IS USED IN THE IPCMPR CARD. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. CAUTION
Use only the SD Memory Card included with the PBX. The SD Memory Card contains software for all the processes of the PBX and all the customer data. The SD Memory Card must be inserted before startup. Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX to fail to start when you try to restart the system. To prevent data leakage, render the SD Memory Card physically unusable before disposal. Pin Assignments RJ45 Connector (10BASE-T/100BASE-TX) No. Signal Name Input (I)/Output (O) Function 1 8 1 2 3 4-5 6 7-8 TPO+
TPO-
TPI+
Reserved TPI-
Reserved O O I I Transmit data+
Transmit data-
Receive data+
Receive data-
80 Installation Manual 3.3 Information about the Main Processing Card LED Indications Indication BATT ALARM Color Red SD ACCESS Green 2
(for PC Maintenance) LINK Green 100 Yellow 1
(for LAN Connection) LINK Green 100 Yellow Description Battery alarm indication
OFF: Normal ON: Alarm SD memory card status
ON: Accessing Link status indication
OFF: Off-line ON: Linked normally Flashing: In communication Data transmission speed indication
OFF: 10 Mbps ON: 100 Mbps Link status indication
OFF: Off-line ON: Linked normally Flashing: In communication Data transmission speed indication
OFF: 10 Mbps ON: 100 Mbps Installation Manual 81 3.3 Information about the Main Processing Card 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) Function DSP16:
DSP64:
16-channel digital signal processor card with an SHGW4 activation key and an IPPT8 activation key pre-installed. Compliant with ITU-T G.729a and G.711 CODEC methods. To be mounted on the IPCMPR card. 64-channel digital signal processor card with four SHGW4 activation keys and four IPPT8 activation keys pre-installed. Compliant with ITU-T G.729a and G.711 CODEC methods. To be mounted on the IPCMPR card. inside DSP16 Card/
DSP64 Card Screw Accessories and User-supplied Items Accessories (included): Screws 3 User-supplied (not included): none Notes
Depending on the number and the type of CO lines and IP telephones you wish to use, required activation keys are determined, and either the DSP16 or DSP64 card is selected to be installed. If the pre-installed activation keys on the DSP16 or DSP64 cards are not enough for the desired configuration, you need to purchase activation key cards. For details about the activation keys, refer to "2.1 Information about the Activation Keys". 82 Installation Manual 3.3 Information about the Main Processing Card 3.3.3 RMT Card (KX-TDA0196) Function Analog modem card for remote communication with the PBX. ITU-T V.90 support. To be mounted on the IPCMPR card. IPCMPR Card inside RMT Card Screw Accessories and User-supplied Items Accessories (included): Screws 2 User-supplied (not included): none Installation Manual 83 3.4 Information about the Virtual Cards 3.4 Information about the Virtual Cards 3.4.1 Virtual Cards Function Virtual Cards are included with the IPCMPR card and can be activated with the appropriate activation key. By installing Virtual Cards in the Virtual Slots of the IPCMPR card using the KX-TDE Maintenance Console, IP CO lines and IP extensions can be used via the IPCMPR card. Virtual Card Description Virtual 16-Channel VoIP Gateway Card
(V-IPGW16) Virtual Card for 16-channel VoIP CO line. Compliant with VoIP H.323 V.5 protocol. Virtual 32-Channel VoIP Extension Card
(V-IPEXT32) Virtual Card for 32 VoIP extensions. Compliant with Panasonic proprietary protocol. Virtual 32-Channel SIP Extension Card
(V-SIPEXT32) Virtual Card for 32 SIP Extensions. Compliant with RFC 3261, 3264, 3310, and 2327 protocols. Example: Virtual Cards in the Virtual Slots Virtual CO Line Slots Virtual Extension Slots IPCMPR Card Virtual Slots 84 Installation Manual 3.5 Information about the Physical Trunk Cards 3.5 Information about the Physical Trunk Cards 3.5.1 LCOT8 Card (KX-TDA0180) and LCOT16 Card (KX-
TDA0181) 8-port analog CO line card with 2 power failure transfer (PFT) ports. One CID8 card can be mounted on the LCOT8 card (refer to "3.5.2 CID8 Card (KX-TDA0193)"). 16-port analog CO line card with 4 power failure transfer (PFT) ports. A maximum of 2 CID8 cards can be mounted on the LCOT16 card (refer to "3.5.2 CID8 Card (KX-TDA0193)"). Function LCOT8:
LCOT16:
LED Amphenol To CO line Accessories and User-supplied Items Accessories (included): Screws 2 User-supplied (not included): Amphenol connector Notes
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector". For details about power failure transfer, refer to "3.13.1 Power Failure Connections". To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting the PBX". Installation Manual 85 3.5 Information about the Physical Trunk Cards Pin Assignments Amphenol Connector No. Signal Name Function No. Signal Name Function 50 25 26 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP Ring port 1 Ring port 2 Ring port 3 Ring port 4 Ring port 5 Ring port 6 Ring port 7 Ring port 8 Ring port 9 Ring port 10 Ring port 11 Ring port 12 Ring port 13 Ring port 14 Ring port 15 Ring port 16 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP Tip port 1 Tip port 2 Tip port 3 Tip port 4 Tip port 5 Tip port 6 Tip port 7 Tip port 8 Tip port 9 Tip port 10 Tip port 11 Tip port 12 Tip port 13 Tip port 14 Tip port 15 Tip port 16 17-25 Reserved 42-50 Reserved Notes
Pin assignments for the pins 5 to 8 and 30 to 33 are for the LCOT8 and LCOT16 card only. Pin assignments for the pins 9 to 16 and 34 to 41 are for the LCOT16 card only. LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service 86 Installation Manual 3.5 Information about the Physical Trunk Cards 3.5.2 CID8 Card (KX-TDA0193) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the LCOT8/LCOT16 cards. LCOT16 card only S W 2 O F F O N inside CID8 Card Screw SW1 O N O F F Accessories and User-supplied Items Accessories (included): Screws 2 User-supplied (not included): none Note Only 1 CID8 card can be mounted on the LCOT8 card. Switch Settings (on LCOT8/LCOT16 cards) Switch Port Setting Type DIP Usage and Status Definition Keep all DIP switches at default "ON" positions. Do not change the positions of these switches. Note SW2 is for the LCOT16 card only. Installation Manual 87 3.5 Information about the Physical Trunk Cards 3.5.3 T1 Card (KX-TDA0187) Function 1-port T1 CO line card. EIA/TIA standard compliant. LEDs RJ45 To NT1 A B Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector Notes
Connect this optional service card to the CO line through NT1; do not connect to the CO line directly. T1 Card must be installed behind an FCC registered and UL or CSA-NRTL listed CSU. To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting the PBX". CAUTION T1 ports are SELV ports and should only be connected to SELV services. Switch Settings Switch A/B Type Slide Usage and Status Definition Keep the switch at default A position. Do not change the position of this switch. 88 Installation Manual 3.5 Information about the Physical Trunk Cards Pin Assignments RJ45 Connector No. Signal Name Level [V]
Function 8 1 1 2 3 4 5 RX+
RX-
Reserved TX-
TX+
6-8 Reserved
(+) Receive data (+) Receive data (-) Transmit data (-) Transmit data (+) LED Indications Indication Color Description CARD STATUS Green/Red SYNC-ERR Red RAI Red AIS Red SYNC Green Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service Non-synchronisation status indication
OFF: Normal ON: Out of synchronisation RAI signal status indication
OFF: Normal ON: Alarm (Clock Slave) Flashing (60 times per minute): Alarm (Clock Master) AIS status indication
OFF: Normal ON: Alarm Synchronisation status indication
OFF: Not synchronised ON: Synchronised Flashing (60 times per minute): Synchronised (Clock Master) Installation Manual 89 3.5 Information about the Physical Trunk Cards 3.5.4 PRI23 Card (KX-TDA0290) Function 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. LEDs RJ45 To NT1 A B Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector Notes
Connect this optional service card to the CO line through an NT1; do not connect to the U interface of the CO line directly. To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting the PBX". CAUTION PRI ports are SELV ports and should only be connected to SELV services. Switch Settings Switch A/B Type Slide Usage and Status Definition Keep the switch at default A position. Do not change the position of this switch. 90 Installation Manual 3.5 Information about the Physical Trunk Cards Pin Assignments RJ45 Connector No. Signal Name Level [V]
Function 8 1 1 2 3 4 5 RX+
RX-
Reserved TX-
TX+
6-8 Reserved
(+) Receive data (+) Receive data (-) Transmit data (-) Transmit data (+) LED Indications Indication Color Description CARD STATUS Green/Red SYNC-ERR Red RAI Red AIS Red SYNC Green Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service Non-synchronisation status indication
OFF: Normal ON: Out of synchronisation RAI signal status indication
OFF: Normal ON: Alarm (Clock Slave) Flashing (60 times per minute): Alarm (Clock Master) AIS status indication
OFF: Normal ON: Alarm Synchronisation status indication
OFF: Not synchronised ON: Synchronised Flashing (60 times per minute): Synchronised (Clock Master) D-LINK Green Data link status indication OFF: Not established
ON: Established Installation Manual 91 3.5 Information about the Physical Trunk Cards 3.5.5 IP-GW4E Card (KX-TDA0484) Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and G.711 CODEC methods. LEDs RJ45
(10BASE-T/100BASE-TX) To private IP network Accessories and User-supplied Items Accessories (included): CD-ROM (including documentation for web programming) 1 User-supplied (not included): RJ45 connector Notes
The maximum length of the cable to be connected to this optional service card is 100 m (328 ft). The IP-GW4E card occupies the space of only 1 free slot when it is installed in the PBX. For programming instructions and other information about the IP-GW4E card, refer to the documentation for the IP-GW4E card. To program the IP-GW4E card, use the web programming designed for the IP-GW4E card. To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting the PBX". Pin Assignments RJ45 Connector (10BASE-T/100BASE-TX) No. Signal Name Input (I)/Output (O) Function 8 1 1 2 3 4-5 6 7-8 TPO+
TPO-
TPI+
Reserved TPI-
Reserved O O I I Transmit data+
Transmit data-
Receive data+
Receive data-
92 Installation Manual 3.5 Information about the Physical Trunk Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service ONLINE Green On-line status indication
ON: On-line mode OFF: Off-line mode Flashing: Maintenance mode Note If the LINK indicator is OFF, the ONLINE indicator will also be OFF. ALARM Red VoIP BUSY Green LINK Green DATA Green Alarm indication
OFF: Normal ON: Alarm VoIP (H.323) process indication
OFF: VoIP process inactive ON: VoIP process active
Link status indication
OFF: Connection error ON: Normal connection Data transmission indication
OFF: No data transmitted ON: Data transmitting Installation Manual 93 3.5 Information about the Physical Trunk Cards 3.5.6 IP-GW16 Card (KX-TDA0490) Function 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and G.711 CODEC methods. LEDs RJ45
(10BASE-T/100BASE-TX Full Duplex) To private IP network Accessories and User-supplied Items Accessories (included): Ferrite core 1, CD-ROM (including documentation for web programming) 1 User-supplied (not included): RJ45 connector Notes
The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
When connecting the RJ45 connector, attach the included ferrite core. Refer to "3.2.8 Attaching a
Ferrite Core". For programming instructions and other information about the IP-GW16 card, refer to the documentation for the IP-GW16 card. To program the IP-GW16 card, use the web programming designed for the IP-GW16 card. To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting the PBX". Pin Assignments RJ45 Connector (10BASE-T/100BASE-TX) No. Signal Name Input (I)/Output (O) Function 8 1 1 2 3 4-5 6 7-8 TPO+
TPO-
TPI+
Reserved TPI-
Reserved O O I I Transmit data+
Transmit data-
Receive data+
Receive data-
94 Installation Manual 3.5 Information about the Physical Trunk Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service ONLINE Green On-line status indication
ON: On-line mode OFF: Off-line mode Flashing: Maintenance mode Note If the LINK indicator is OFF, the ONLINE indicator will also be OFF. ALARM Red VoIP BUSY Green LINK Green DATA Green Alarm indication
OFF: Normal ON: Alarm VoIP (H.323) process indication
OFF: VoIP process inactive ON: VoIP process active
Link status indication
OFF: Connection error ON: Normal connection Data transmission indication
OFF: No data transmitted ON: Data transmitting Installation Manual 95 3.6 Information about the Physical Extension Cards 3.6 Information about the Physical Extension Cards 3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Function CSIF4: 4-port CS interface card for 4 CSs. CSIF8: 8-port CS interface card for 8 CSs. LED RJ45
(LINE 1 to LINE 8) To CS Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector CAUTION Make sure that the status of all the CSs connected to the CSIF cards are set to in-service (INS). For information about how to view CS information using the KX-TDE Maintenance Console, refer to "2.5.14 UtilityCS Information" in the PC Programming Manual. If there is a CS in out-of-service (OUS) status, make sure that it is securely connected to the CSIF card. If the CS remains in OUS status, there may be a fault with the connection. Do not leave the connected CS in OUS status since it may cause severe damage to the CSIF card. LINE 5 to LINE 8 are for CSIF8 card only. Notes
When using the CSIF4 card, please note that the PBX software will recognise the CSIF4 card as the CSIF8 card. As a result, 8 cell stations may appear to be available; however, only 4 cell stations are supported by the CSIF4 card. For details about connecting the CS, refer to "3.9.7 Connecting a Cell Station to the PBX" in "3.9 Connection of 2.4 GHz Portable Stations".
96 Installation Manual 3.6 Information about the Physical Extension Cards Editing the CS Name using the KX-TDE Maintenance Console While programming the PBX, we strongly recommend that you input a unique recognizable CS name
(maximum 20 characters) for each CS port in use, and "(Reserved)" or "(Not for CSIF4)" for unused ports or unavailable ports respectively for the following reasons:
a. b. you will be able to easily distinguish installed CSs. you will be able to know which CSIF card has been installed; CSIF4 or CSIF8. Example: When the CSIF4 card has been installed*1 Pin Assignments RJ45 Connector 8 1 No. 1-2 3 4 5 6 Signal Name Function Reserved D1 POWH POWL D2 Data port (High) Power (High) Power (Low) Data port (Low) 7-8 Reserved
*1 The contents and design of the software are subject to change without notice. Installation Manual 97 3.6 Information about the Physical Extension Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service 98 Installation Manual 3.6 Information about the Physical Extension Cards 3.6.2 DHLC8 Card (KX-TDA0170) Function 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs (Basic/High-
density), with 2 power failure transfer (PFT) ports. LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws 2, Ferrite core 1 User-supplied (not included): Amphenol connector Notes
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector". For details about power failure transfer, refer to "3.13.1 Power Failure Connections". Installation Manual 99 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector 50 25 26 1 No. Signal Name Function No. Signal Name Function 1 2 3 4 5 6 7 8 9 RA D2A SLT Ring port 1 26 TA SLT Tip port 1 PT Data port 1 (Low) 27 D1A PT Data port 1 (High) Reserved 28 Reserved RB D2B SLT Ring port 2 29 TB SLT Tip port 2 PT Data port 2 (Low) 30 D1B PT Data port 2 (High) Reserved 31 Reserved RC D2C SLT Ring port 3 32 TC SLT Tip port 3 PT Data port 3 (Low) 33 D1C PT Data port 3 (High) Reserved 34 Reserved 10 RD 11 D2D SLT Ring port 4 35 TD SLT Tip port 4 PT Data port 4 (Low) 36 D1D PT Data port 4 (High) 12 Reserved 37 Reserved 13 RE 14 D2E SLT Ring port 5 38 TE SLT Tip port 5 PT Data port 5 (Low) 39 D1E PT Data port 5 (High) 15 Reserved 40 Reserved 16 RF 17 D2F SLT Ring port 6 41 TF SLT Tip port 6 PT Data port 6 (Low) 42 D1F PT Data port 6 (High) 18 Reserved 43 Reserved 19 RG 20 D2G SLT Ring port 7 44 TG SLT Tip port 7 PT Data port 7 (Low) 45 D1G PT Data port 7 (High) 21 Reserved 46 Reserved 22 RH 23 D2H SLT Ring port 8 47 TH SLT Tip port 8 PT Data port 8 (Low) 48 D1H PT Data port 8 (High) Reserved 24-
25 Reserved 49-
50 100 Installation Manual 3.6 Information about the Physical Extension Cards LED Indications Indication Color Description CARD STATUS Green/
Orange/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Orange Flashing: Detection of PT-interface CS connection (when starting up the PT-interface CS [Basic/High-density]) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service
Installation Manual 101 3.6 Information about the Physical Extension Cards 3.6.3 DLC8 Card (KX-TDA0171) Function 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-density). LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws 2, Ferrite core 1 User-supplied (not included): Amphenol connector Notes
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector". 102 Installation Manual 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector No. Signal Name Function No. Signal Name Function 50 25 26 1 1 2 3-4 5 6-7 8 Reserved D2A Data port 1 (Low) 26 27 Reserved D1A Data port 1 (High) Reserved 28-29 Reserved D2B Data port 2 (Low) 30 D1B Data port 2 (High) Reserved 31-32 Reserved D2C Data port 3 (Low) 33 D1C Data port 3 (High) 9-10 Reserved 34-35 Reserved 11 D2D Data port 4 (Low) 36 D1D Data port 4 (High) 12-13 Reserved 37-38 Reserved 14 D2E Data port 5 (Low) 39 D1E Data port 5 (High) 15-16 Reserved 40-41 Reserved 17 D2F Data port 6 (Low) 42 D1F Data port 6 (High) 18-19 Reserved 43-44 Reserved 20 D2G Data port 7 (Low) 45 D1G Data port 7 (High) 21-22 Reserved 46-47 Reserved 23 D2H Data port 8 (Low) 48 D1H Data port 8 (High) 24-25 Reserved 49-50 Reserved LED Indications Indication Color Description CARD STATUS Green/
Orange/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Orange Flashing: Detection of PT-interface CS connection (when starting up the PT-interface CS [Basic/High-density]) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service
Installation Manual 103 3.6 Information about the Physical Extension Cards 3.6.4 DLC16 Card (KX-TDA0172) Function 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-density). LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws 2, Ferrite core 1 User-supplied (not included): Amphenol connector Notes
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector". 104 Installation Manual 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector No. Signal Name Function No. Signal Name Function 50 25 26 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D2A D2B D2C D2D D2E D2F D2G D2H D2I D2J D2K D2L D2M D2N D2O D2P Data port 1 (Low) Data port 2 (Low) Data port 3 (Low) Data port 4 (Low) Data port 5 (Low) Data port 6 (Low) Data port 7 (Low) Data port 8 (Low) Data port 9 (Low) 26 27 28 29 30 31 32 33 34 Data port 10 (Low) 35 Data port 11 (Low) 36 Data port 12 (Low) 37 Data port 13 (Low) 38 Data port 14 (Low) 39 Data port 15 (Low) 40 Data port 16 (Low) 41 D1A D1B D1C D1D D1E D1F D1G D1H D1I D1J D1K D1L D1M D1N D1O D1P Data port 1 (High) Data port 2 (High) Data port 3 (High) Data port 4 (High) Data port 5 (High) Data port 6 (High) Data port 7 (High) Data port 8 (High) Data port 9 (High) Data port 10 (High) Data port 11 (High) Data port 12 (High) Data port 13 (High) Data port 14 (High) Data port 15 (High) Data port 16 (High) 17-25 Reserved 42-50 Reserved LED Indications Indication Color Description CARD STATUS Green/
Orange/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Orange Flashing: Detection of PT-interface CS connection (when starting up the PT-interface CS [Basic/High-density]) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service
Installation Manual 105 3.6 Information about the Physical Extension Cards 3.6.5 SLC8 Card (KX-TDA0173) Function 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws 2, Ferrite core 1 User-supplied (not included): Amphenol connector Notes
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector". For details about power failure transfer, refer to "3.13.1 Power Failure Connections". 106 Installation Manual 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector 50 25 26 1 No. 1 2-3 4 5-6 7 8-9 10 Signal Name Function RA Ring port 1 No. 26 Signal Name Function TA Tip port 1 Reserved 27-28 Reserved RB Ring port 2 29 TB Tip port 2 Reserved 30-31 Reserved RC Ring port 3 32 TC Tip port 3 Reserved 33-34 Reserved RD Ring port 4 35 TD Tip port 4 11-12 Reserved 36-37 Reserved 13 RE Ring port 5 38 TE Tip port 5 14-15 Reserved 39-40 Reserved 16 RF Ring port 6 41 TF Tip port 6 17-18 Reserved 43-44 Reserved 19 RG Ring port 7 44 TG Tip port 7 20-21 Reserved 45-46 Reserved 22 RH Ring port 8 47 TH Tip port 8 23-25 Reserved 48-50 Reserved LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service Installation Manual 107 3.6 Information about the Physical Extension Cards 3.6.6 EXT-CID Card (KX-TDA0168) Function Sends Caller ID signals to extension ports. To be mounted on the SLC8 card only. SLC8 Card inside Screw EXT-CID Card Accessories and User-supplied Items Accessories (included): Screws 2 User-supplied (not included): none 108 Installation Manual 3.6.7 SLC16 Card (KX-TDA0174) and MSLC16 Card (KX-
TDA0175) 3.6 Information about the Physical Extension Cards 16-port extension card for SLTs with 4 power failure transfer (PFT) ports. 16-port extension card for SLTs with Message Waiting Lamp control and 4 power failure transfer (PFT) ports. Maximum power output of 160 V/90 V for Message Waiting Lamp control. Function SLC16:
MSLC16:
LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws 2, Ferrite core 1 User-supplied (not included): Amphenol connector Notes
Panasonic SLT with Message Waiting Lamp (e.g., KX-T7310) is recommended for connection to the MSLC16 card. Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector". For details about power failure transfer, refer to "3.13.1 Power Failure Connections". Installation Manual 109 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector No. Signal Name Function No. Signal Name Function 50 25 26 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP Ring port 1 Ring port 2 Ring port 3 Ring port 4 Ring port 5 Ring port 6 Ring port 7 Ring port 8 Ring port 9 Ring port 10 Ring port 11 Ring port 12 Ring port 13 Ring port 14 Ring port 15 Ring port 16 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP Tip port 1 Tip port 2 Tip port 3 Tip port 4 Tip port 5 Tip port 6 Tip port 7 Tip port 8 Tip port 9 Tip port 10 Tip port 11 Tip port 12 Tip port 13 Tip port 14 Tip port 15 Tip port 16 17-25 Reserved 42-50 Reserved LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service 110 Installation Manual 3.6 Information about the Physical Extension Cards 3.6.8 IP-EXT16 Card (KX-TDA0470) Function 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods. LEDs RJ45
(10BASE-T/100BASE-TX Full Duplex) To LAN Accessories and User-supplied Items Accessories (included): Ferrite core 1 User-supplied (not included): RJ45 connector Notes
The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
When connecting the RJ45 connector, attach the included ferrite core. Refer to "3.2.8 Attaching a Ferrite Core". Pin Assignments RJ45 Connector (10BASE-T/100BASE-TX) No. Signal Name Input (I)/Output (O) Function 8 1 1 2 3 4-5 6 7-8 TPO+
TPO-
TPI+
Reserved TPI-
Reserved O O I I Transmit data+
Transmit data-
Receive data+
Receive data-
Installation Manual 111 3.6 Information about the Physical Extension Cards LED Indications Indication Color Description CARD STATUS Green/Red ONLINE Green ALARM Red VoIP BUSY Green LINK Green DATA Green Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service On-line status indication
ON: At least one port is in use (an IP-PT is connected) OFF: No ports are in use (no IP-PTs are connected) Note If the LINK indicator is OFF, the ONLINE indicator will also be OFF. Alarm indication
OFF: Normal ON: Alarm Panasonic proprietary VoIP protocol process indication
OFF: VoIP process inactive ON: VoIP process active Link status indication
OFF: Connection error ON: Normal connection Data transmission indication
OFF: No data transmitted ON: Data transmitting 112 Installation Manual 3.7 Information about the Other Physical Cards 3.7 Information about the Other Physical Cards 3.7.1 OPB3 Card (KX-TDA0190) Function Optional 3-slot base card for mounting a maximum of 3 option cards from the following:
DPH4 card EIO4 card ECHO16 card
MSG4 card LED Accessories and User-supplied Items Accessories (included): none User-supplied (not included): none WARNING A LITHIUM BATTERY IS USED IN OPB3 CARD. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. LED Indications Indication Color Description CARD STATUS Green/Red Card status indication
OFF: Power Off Green ON: Normal (all ports are idle) Green Flashing (60 times per minute): Normal (a port is in use) Red ON: Fault (includes reset) Red Flashing (60 times per minute): Out of Service Installation Manual 113 3.7 Information about the Other Physical Cards 3.7.2 DPH4 Card (KX-TDA0161) Function 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. OPB3 Card DPH4 Card 8-pin Screw To doorphones To door openers 10-pin Accessories and User-supplied Items Accessories (included): Screws 3, 10-pin terminal block 1, 8-pin terminal block 1 User-supplied (not included): Copper wire Note For details about connection to doorphones and door openers, refer to "3.10.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays". 114 Installation Manual 3.7 Information about the Other Physical Cards Pin Assignments 8-pin Terminal Block No. Signal Name Function 1 8 1 2 3 4 5 6 7 8 DP4 com4 DP3 com3 DP2 com2 DP1 com1 10-pin Terminal Block Doorphone 4 transmit Doorphone 4 receive Doorphone 3 transmit Doorphone 3 receive Doorphone 2 transmit Doorphone 2 receive Doorphone 1 transmit Doorphone 1 receive 1 10 No. 1-2 3 4 5 6 7 8 9 10 Signal Name Function Reserved OP4b OP4a OP3b OP3a OP2b OP2a OP1b OP1a Door opener 4 Door opener 4 com Door opener 3 Door opener 3 com Door opener 2 Door opener 2 com Door opener 1 Door opener 1 com Installation Manual 115 3.7 Information about the Other Physical Cards 3.7.3 EIO4 Card (KX-TDA0164) Function 4-port external input/output card. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. OPB3 Card EIO4 Card 8-pin Screw To external sensors To external relays 10-pin Accessories and User-supplied Items Accessories (included): Screws 3, 10-pin terminal block 1, 8-pin terminal block 1 User-supplied (not included): Copper wire Note For details about connection to external sensors and external relays, refer to "3.10.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays". 116 Installation Manual 3.7 Information about the Other Physical Cards Pin Assignments 8-pin Terminal Block No. Signal Name 1 8 1 2 3 4 5 6 7 8 C4b C4a C3b C3a C2b C2a C1b C1a 10-pin Terminal Block Function Control 4 Control 4 com Control 3 Control 3 com Control 2 Control 2 com Control 1 Control 1 com 1 10 No. 1-2 3 4 5 6 7 8 9 10 Signal Name Function Reserved OP4b OP4a OP3b OP3a OP2b OP2a OP1b OP1a Opener 4 Opener 4 com Opener 3 Opener 3 com Opener 2 Opener 2 com Opener 1 Opener 1 com Installation Manual 117 3.7 Information about the Other Physical Cards External Sensor Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card for each external sensor. The PBX detects input from the sensor when the signal is under 100 . Connection Diagram External Sensor PBX OPB3 EIO4
+5V I/O 10K 4.7K 4.7K
+5V 33 33 sensor common External Relay Current Limit: 24 V DC/30 V AC, 1 A maximum 118 Installation Manual 3.7 Information about the Other Physical Cards 3.7.4 ECHO16 Card (KX-TDA0166) Function 16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card. OPB3 Card ECHO16 Card inside Screw Accessories and User-supplied Items Accessories (included): Screws 3 User-supplied (not included): none Note To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable echo cancellation for conferences using the KX-TDE Maintenance Console. For details, refer to "Echo CancelConference" in "2.8.18 [2-9] System Options" of the PC Programming Manual. Installation Manual 119 3.7 Information about the Other Physical Cards 3.7.5 MSG4 Card (KX-TDA0191) Function 4-channel message card. To be mounted on the OPB3 card. OPB3 Card MSG4 Card inside Screw Accessories and User-supplied Items Accessories (included): Screws 3 User-supplied (not included): none 120 Installation Manual 3.8 Connection of Extensions 3.8 Connection of Extensions 3.8.1 Maximum Cabling Distances of the Extension Wiring
(Twisted Cable) Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance 222 m (728 ft) 347 m (1138 ft) 500 m (1640 ft) 347 m (1138 ft) Maximum Distance 500 m (1640 ft) 720 m (2362 ft) 830 m (2723 ft) 720 m (2362 ft) Maximum Distance 140 m (459 ft) 229 m (751 ft) 360 m (1181 ft) 229 m (751 ft) Maximum Distance 698 m (2289 ft) 1128 m (3700 ft) 1798 m (5897 ft) 1128 m (3700 ft) PT-interface CS
(Basic/High-density) KX-T7600 Series DPT*
Other PT (DPT/APT) and DSS Console SLT
* The maximum cabling distance from the PBX is the same even when the KX-T7600 series DPT is the master DPT on the Digital XDP connection. Notice The maximum cabling distance may vary depending on the conditions. Installation Manual 121 3.8 Connection of Extensions PT-interface CS
(Basic/High-
density) DPT APT DSS Console SLT DHLC8 Card MSLC16, SLC16, SLC8 Cards DLC16, DLC8 Cards
" indicates that the extension card supports the terminal. 122 Installation Manual 3.8 Connection of Extensions 3.8.2 Parallel Connection of the Extensions Any SLT can be connected in parallel with an APT or a DPT as follows. Note In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in parallel with an APT or a DPT. With APT For parallel connection, eXtra Device Port (XDP) mode must be disabled for that port through system programming. Refer to "1.11.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Manual for further information. To DHLC8 card Modular T-Adaptor 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1", and "D2". APT SLT Installation Manual 123 3.8 Connection of Extensions With DPT Parallel mode or eXtra Device Port (XDP) mode can be selected through system programming. If XDP mode is enabled through system programming, parallel connection is not possible. Refer to "1.11.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Manual for further information. Using a Modular T-Adaptor To DHLC8 card 4-conductor wiring cord Connect pins "D1" and
"D2". Modular T-Adaptor 2-conductor wiring cord Connect pins "T" and "R". DPT SLT Using an EXtra Device Port With KX-T7600 Series DPT (except KX-T7665) To DHLC8 card 4-conductor wiring cord Connect pins "T", "R",
"D1" and "D2". 2-conductor wiring cord Connect pins "T" and "R". DPT SLT TO MAIN UNIT TO TEL
/ PABX To DHLC8 card To SLT 124 Installation Manual 3.8 Connection of Extensions With Other DPT To DHLC8 card 4-conductor wiring cord Connect pins "T", "R",
"D1" and "D2". 2-conductor wiring cord Connect pins "T" and "R". DPT SLT TO EMSS or TO MAIN UNIT To DHLC8 card TO TEL To SLT Installation Manual 125 3.8 Connection of Extensions 3.8.3 Digital EXtra Device Port (Digital XDP) Connection A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode. Notes
Both DPTs must be KX-T7600 series DPTs (except KX-T7640). Note that the KX-T7667 can only be connected as a slave DPT. Parallel mode or XDP mode can be selected through system programming. If XDP mode is enabled through system programming, parallel connection is not possible. Refer to
"1.11.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Manual for further information. With KX-T7600 Series DPT Using a Modular T-Adaptor To DLC8/DLC16 card To DHLC8 card
(for connection of SLT) 4-conductor wiring cord Connect pins "D1" and
"D2". Modular T-Adaptor 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "D1" and "D2". SLT TO MAIN UNIT
/ PABX Back View of DPTs TO TEL Master DPT Slave DPT Maximum Distance Cable 26 AWG: 30 m (98 ft) 24 AWG: 50 m (164 ft) 22 AWG: 60 m (196 ft) CAT 5:
50 m (164 ft) TO MAIN UNIT
/ PABX Master DPT Slave DPT To DLC8/DLC16 card To DHLC8 card
(for connection of SLT) 126 Installation Manual 3.8 Connection of Extensions Using an EXtra Device Port To DLC8/DLC16 card To DHLC8 card
(for connection of SLT) 4-conductor wiring cord Connect pins "T", "R",
"D1" and "D2". 4-conductor wiring cord Connect pins "T", "R",
"D1" and "D2". 2-conductor wiring cord Connect pins "T" and "R". Back View of DPTs TO TEL Master DPT Slave DPT SLT TO MAIN UNIT
/ PABX Maximum Distance Cable 26 AWG: 30 m (98 ft) 24 AWG: 50 m (164 ft) 22 AWG: 60 m (196 ft) 50 m (164 ft) CAT 5:
TO MAIN UNIT
/ PABX Master DPT Slave DPT TO TEL To DLC8/DLC16 card To SLT To DHLC8 card
(for connection of SLT) Installation Manual 127 3.8 Connection of Extensions 3.8.4 First Party Call Control CTI Connection CTI connection between a PC and a KX-T7633/T7636 DPT provides first party call control. The CTI connection is made via a USB interface (version 2.0), and uses the TAPI 2.1 protocol. A USB Module (KX-T7601) must be connected to the KX-T7633/T7636 DPT. Note The operating system of the PC required for first party call control depends on your CTI application software. For details, refer to the manual for your CTI application software. To PC USB Cable USB Port L L U USB Module Notes
The maximum length of the USB cable is 3 m (9 ft 10 in). USB Modules must not be connected to DPTs in the Digital XDP connection. In a Digital XDP connection, the PC cannot be used. If a USB module is connected to a slave DPT, the DPT will not work properly. 128 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations 3.9 Connection of 2.4 GHz Portable Stations 3.9.1 Overview Radio Methods There are new and old radio methods for the 2.4 GHz wireless system. The radio method can be selected through system programming. Make sure that all CSs on a wireless system have the same radio method. Required Equipment and Maximum Number of Calls CSs determine the area covered by the wireless system. The number of calls that can be made simultaneously through each CS varies depending on the model and radio method, as follows:
Radio Method CS Connection Card Maximum Calls Compatible PSs New KX-T0151 DHLC/DLC KX-TDA0152 CSIF KX-TDA0158 KX-T0151 DHLC/DLC DHLC/DLC KX-TDA0152 CSIF KX-T0141 DHLC/DLC KX-TDA0142 CSIF Old Note 2 4 5 2 3 2 3
KX-TD7685 KX-TD7695 KX-TD7684 KX-TD7694 KX-TD7680 KX-TD7690 For more details about the PS, refer to the Operating Instructions of the PS. CAUTION
C C
), low temperature The CS should be kept free of dust, moisture, high temperature (more than 40
(less than 0
), and vibration, and should not be exposed to direct sunlight. The CS should not be placed outdoors (use indoors). The CS should not be placed near high-voltage equipment. The CS should not be placed on a metal object. Systems using 2.4 GHz ISM (Industrial, Scientific and Medical) band may interfere with the KX-
TDA wireless system. Examples of such systems are cordless telephones, wireless LAN, Home RF, microwave ovens and other ISM devices. These systems may cause minor noise. Keeping some distance between the equipment listed below may prevent interference. (The distance may vary depending on the environment.) Equipment Distance CS and office equipment such as a computer, telex, fax machine, etc. More than 2 m (6 ft 7 in) CS and PS Each PS PBX and CS More than (3 ft 3 in) More than 0.5 m (1 ft 8 in) More than 2 m (6 ft 7 in) Installation Manual 129 3.9 Connection of 2.4 GHz Portable Stations Equipment CS and CS Distance More than 15 m (49 ft) Please take into consideration the distance between the CSs when site planning. Please consult a certified dealer for details. However, the required distance between CSs may vary depending on the environment of the installation site and conditions in which the wireless system is used. Conduct the site survey to determine the appropriate distance. 130 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations 3.9.2 Procedure Overview When connecting the wireless system, use extreme care in conducting the site survey. An incorrectly performed site survey can result in poor service area, frequent noise, and disconnection of calls. 1. Investigate the installation site Refer to "3.9.3 Site Planning". a. Obtain a map of the CS installation site. b. c. Plan the location of each CS, taking account of distance, building materials, etc. Identify the service area required by the user on the map. 2. Prepare the CS for site survey Refer to "3.9.4 Before Site Survey". a. Assign a CS number to each CS by setting the DIP switches on the back of the CS. b. Supply electricity to each CS using an AC adaptor or a battery box. c. Install each CS temporarily as planned. Notes
Install at least 2 m (6 ft 7 in) above the floor. Keep the antennas in the upright position. 3. Conduct the site survey Refer to "3.9.5 Site Survey". a. Test the radio signal strength using the PS. Confirm that the radio signal strength level is "12" near the CS. Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 0 0 1 9 Press 1, 9, and POWER for more than 2 seconds. Using the KX-TD7680 1 9 Press 1, 9, and POWER for more than 2 seconds. Using the KX-TD7690 1 99 Press 1, 9, and POWER for more than 2 seconds. Display example:
<< SEARCHING >>
CS NO.1 LEVEL:12 SAVE:0123456789 CS No. 1 to 9 Display example:
<< SEARCHING >>
CS No. 1 to 9 CS NO.1 LEVEL:12 SAVE:0123456789 Display example:
<< SEARCHING >>
CS No. 1 to 9 CS NO.1 LEVEL:12 SAVE:0123456789 b. By walking away from the CS with the PS, check the radio signal strength. The radio signal strength weakens as you walk away from the CS. c. Map the CS coverage area at radio signal strength levels "3" and "8". Installation Manual 131 3.9 Connection of 2.4 GHz Portable Stations d. Make sure that adjacent CS coverage areas overlap where the radio signal strength level is "8" by at least 5 m (16 ft). e. Make sure that the radio signal strength level is greater than "3" at any location within the service area required by the user. 4. Finish the site survey Refer to "3.9.6 After Site Survey". a. Return all DIP switches of each CS to the OFF position, and stop supplying power. b. Turn off the PS. 5. Connect the CS and PS to the PBX and test the operation Refer to "3.9.7 Connecting a Cell Station to the PBX". a. Connect the CSs to the PBX. b. Register the PSs to the PBX. c. Walk around the service area while having a conversation using a registered PS. If noise is frequent or conversations disconnect, relocate the CSs or install an additional CS. 6. Mount the CS on the wall Refer to "3.9.8 Wall Mounting". a. If there are no problems in testing, mount the CS on the wall. 132 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations 3.9.3 Site Planning Choosing the best site for the CS requires careful planning and testing of essential areas. The best location may not always be convenient for installation. Read the following information before installing the unit. Understanding Radio Waves Characteristics of Radio Waves The transmission of radio waves and the CS coverage area depend on the structure and materials of the building. Office equipment, such as computers and fax machines, can interfere with radio waves. Such equipment may create noise or interfere with the performance of the PS. The illustration below shows the special transmitting patterns of radio waves. 1. Radio waves are reflected by objects made of materials such as metal. 2. Radio waves are diffracted by objects such as metallic columns. 3. Radio waves penetrate objects made of materials such as glass. CS 1. Reflection Column 2. Diffraction 3. Penetration Relationships Between Radio Waves and Building Structure and Materials
The CS coverage area is affected more by the building materials and their thickness than the number of obstacles. Radio waves tend to be reflected or diffracted by conductive objects and rarely penetrate them. Radio waves tend to penetrate insulated objects and are rarely reflected by them. Radio waves penetrate thin objects more than thick objects. The table below shows the transmission tendency of radio waves when they reach objects made from various materials. Installation Manual 133 3.9 Connection of 2.4 GHz Portable Stations Object Wall Material Concrete Transmission Tendency The thicker they are, the less radio waves penetrate them. Ferroconcrete Radio waves can penetrate them, but the more iron there is, the more radio waves are reflected. Window Glass Radio waves usually penetrate them. Glass with wire net Radio waves can penetrate them, but tend to be reflected. Glass covered with heat-
resistant film Radio waves are weakened considerably when they penetrate windows. Floor Ferroconcrete Partition Steel Radio waves can penetrate them, but the more iron there is, the more radio waves are reflected. Radio waves are reflected and rarely penetrate them. Plywood, Glass Radio waves usually penetrate them. Column Ferroconcrete Cabinet Metal Steel Wood Radio waves can penetrate them, but the more iron there is, the more radio waves tend to be reflected or diffracted. Radio waves tend to be reflected or diffracted. Radio waves are usually reflected or diffracted, and rarely penetrate them. Radio waves can penetrate them, but they are weakened. 134 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations CS Coverage Area The example below shows the size of the coverage area of 1 CS if it is installed in an area with no obstacles. Note Radio signal strength levels are measured during the site survey (refer to "3.9.5 Site Survey"). A B A Coverage Area Radio signal strength level is greater than "3".
(About 50 m to 60 m
[164 ft to 197 ft]) B Good Coverage Area Radio signal strength level is greater than "8".
(About 30 m to 40 m
[98 ft to 131 ft]) Good sound quality can be maintained. C Out of Service:
Cannot make/receive calls Gray Zone:
Conversation will be intermittent Radio Signal Strength Levels Level: 00 Level: 01 to 02 Level: 03 to 07 Level: 08 to 10 Level: 11 to 12 Out of range Receives noise easily or disconnects May receive noise Good Better Site Survey Preparation 1. Obtain a map and investigate the installation site. a. Check the obstacles (e.g., shelves, columns, and partitions). b. Check the materials of the structures (e.g., metal, concrete, and plywood). c. Check the layout and dimensions of the room, corridor, etc. d. Write down the above information on the map. 2. Examine the service area required by the user on the map, referring to the following example. a. Draw the coverage area around a CS. Extend the coverage area 30 to 60 meters (98 to 197 feet) b. in each direction, depending on the materials of the building structures and obstacles in the installation site. Note that a CS cannot be installed outside a building. If one CS cannot cover the entire service area, install additional CSs as required. Overlap the coverage areas of adjacent CSs. Where CS coverage areas overlap, the PS will start call handover to the next CS if the signal from Installation Manual 135 3.9 Connection of 2.4 GHz Portable Stations one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available for handover, the PS may go out of range and the call could be lost. If the signal from the CS fades, due to the structure of the building, there may be some handover delay. The user will hear a range warning before handover in this case. This also applies in the case of interference from 2.4 GHz apparatus. Example: Installing in a Room Separated by Interior Walls Things to take note of:
The room is separated by interior walls. The room is surrounded by concrete walls. CS installation plan:
The coverage area of each CS will not extend as far as when there are no obstacles, because the radio signals will be weakened by separating walls. Therefore, you will need 5 CSs to cover the entire room. 150 m (492 ft) 70 m
(230 ft) 136 Installation Manual CS no. 1 CS no. 2 CS no. 5 CS no. 3 CS no. 4 3.9 Connection of 2.4 GHz Portable Stations 3.9.4 Before Site Survey Setting and Installing the CS Temporarily for Site Survey 1. Switch the Radio Signal Test switch from OFF to ON. 2. Set the CS number switches as desired. KX-T0151/KX-TDA0152 1 2 3 4 5 6 DIP Switch ON OFF CS Number Switch Keep this switch at the default
"OFF" position. Otherwise, the CS will not function. Radio Signal Test Switch 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 CS no. 1 CS no. 2 CS no. 3 CS no. 4 CS no. 5 CS no. 6 CS no. 7 CS no. 8 CS no. 9 Installation Manual 137 3.9 Connection of 2.4 GHz Portable Stations KX-TDA0158 Radio Signal Test Switch Keep this switch at the default
"OFF" position. Otherwise, the CS will not function. CS Number Switch OFF ON 6 5 4 3 2 1 DIP Switch CS no. 1 CS no. 2 CS no. 3 CS no. 4 CS no. 5 CS no. 6 CS no. 7 CS no. 8 CS no. 9 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 138 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations KX-T0141/KX-TDA0142 DIP Switch OFF ON 1 2 3 4 5 6 CS Number Switch Keep this switch at the default
"OFF" position. Otherwise, the CS will not function. Radio Signal Test Switch CS no. 1 CS no. 2 CS no. 3 CS no. 4 CS no. 5 CS no. 6 CS no. 7 CS no. 8 CS no. 9 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 Note If more than 1 CS is in Radio Signal Test mode, each CS must have a unique CS number. Installation Manual 139 3.9 Connection of 2.4 GHz Portable Stations 3. After setting the DIP switch, connect an AC adaptor or battery box to the CS using a power supply adaptor. Note The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. KX-T0151/KX-TDA0152 KX-TDA0158 KX-T0141/KX-TDA0142 Modular Telephone Cord Modular Telephone Cord
(PSJA1017Z) Modular Telephone Cord Power Supply Adaptor
(PSZZ1TDA0142) Power Supply Adaptor
(PSZZ1TDA0142) Power Supply Adaptor
(PSZZ1TDA0142) To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE) To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE) To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE) 4. Install the CS temporarily for the site survey. Install the CS at least 2 m (6 ft 7 in) above the floor, keeping the antennas in the upright position. 140 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations 3.9.5 Site Survey The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the CSs temporarily, set the PS to Radio Signal Test mode and measure each CS coverage area. Then, record the results on the map of the installation site. Testing the Radio Signal Strength Note Display prompts for the site survey are only available in English. 1. Enter Radio Signal Test mode. Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 1 99 0 Press 1, 9, and POWER for more than 2 seconds. CS No. 1 to 9 Display example:
<< SEARCHING >>
CS NO.1 LEVEL:12*1 SAVE:0123456789*2 To store the scan data Scan Data No. 0 to 9 Using the KX-TD7680 1 99 0 Press 1, 9, and POWER for more than 2 seconds. CS No. 1 to 9 Display example:
<< SEARCHING >>
CS NO.1 LEVEL:12*1 SAVE:0123456789*2 To store the scan data Scan Data No. 0 to 9 Using the KX-TD7690 1 99 0 Press 1, 9, and POWER for more than 2 seconds. CS No. 1 to 9 Display example:
<< SEARCHING >>
CS NO.1 LEVEL:12*1 SAVE:0123456789*2 To store the scan data Scan Data No. 0 to 9 Notes
*1: CS number and radio signal strength level.
*2: Scan data (test result) number. Empty memory space will be indicated by a number; stored memory space will be indicated by a "-". Installation Manual 141 3.9 Connection of 2.4 GHz Portable Stations 2. Measure the radio signal strength by moving towards and away from the CS. a. Move to the CS until the radio signal strength level becomes "12". b. Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "8". Draw the area on the map. c. Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "3". Draw the area on the map. PS CS NO.1 LEVEL:12 CS no. 1 PS CS NO.1 LEVEL:8 PS CS NO.1 LEVEL:3 Radio Signal Strength Levels Level: 00 Level: 01 to 02 Level: 03 to 07 Level: 08 to 10 Level: 11 to 12 Out of range Receives noise easily or disconnects May receive noise Good Better 3. Repeat steps 1 and 2 for other CSs, and relocate the CSs when necessary. a. Overlap adjacent CS coverage areas where the radio signal strength level is "8" by 5 to 10 meters
(16 to 33 feet). CS no. 1 CS no. 2 5 m to 10 m
(16 ft to 33 ft) 142 Installation Manual b. Overlap the CS coverage areas of at least 2 CSs at any location in the installation site. 3.9 Connection of 2.4 GHz Portable Stations CS no. 1 CS no. 2 CS no. 3 CS no. 4 c. Make sure that the radio signal strength level is greater than "3" at any location in the service area required by the user. Referring to the Stored Scan Data Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 1 9 Press 1, 9, and POWER for more than 2 seconds. 1 Scan Data No. 0 to 9 To the Desired Scan Data No. Using the KX-TD7680 1 9 Press 1, 9, and POWER for more than 2 seconds. 1 Scan Data No. 0 to 9 To the Desired Scan Data No. Display example:
When there is scan data NO.1 CS No.2 LEVEL: 9 When there is no scan data NO.0 NOT SAVED Display example:
When there is scan data NO.1 CS No.2 LEVEL: 9 When there is no scan data NO.0 NOT SAVED Installation Manual 143 3.9 Connection of 2.4 GHz Portable Stations Using the KX-TD7690 1 9 Press 1, 9, and POWER for more than 2 seconds. 1 Scan Data No. 0 to 9 To the Desired Scan Data No. Display example:
When there is scan data NO.1 CS No.2 LEVEL: 9 When there is no scan data NO.0 NOT SAVED Deleting the Stored Scan Data Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 1 99 Press 1, 9, and POWER for more than 2 seconds. Using the KX-TD7680 1 9 Press 1, 9, and POWER for more than 2 seconds. 22 2 Scan Data No. 0 to 9, or # for all data To the Desired Scan Data No. Scan Data No. 0 to 9, or # for all data To the Desired Scan Data No. Using the KX-TD7690 1 9 2 Press 1, 9, and POWER for more than 2 seconds. Scan Data No. 0 to 9, or # for all data To the Desired Scan Data No. 144 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations 3.9.6 After Site Survey After obtaining the proper measurement results, exit Radio Signal Test mode before connecting the CS to the PBX. 1. Keep pressing the POWER button on the PS until the PS is turned OFF. 2. Disconnect the AC adaptor or battery box from the CS and stop supplying electricity. KX-T0151/KX-TDA0152 KX-TDA0158 KX-T0141/KX-TDA0142 3. Switch all DIP switches on the CS from ON to OFF. OFF ON 1 2 3 4 5 6 Installation Manual 145 3.9 Connection of 2.4 GHz Portable Stations 3.9.7 Connecting a Cell Station to the PBX Using a CSIF Card Refer to the following example to connect a CS to the PBX. KX-TDA0152/KX-TDA0142 CSIF8 Card Port 1 Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance 444 m (1457 ft) 694 m (2277 ft) 1000 m (3281 ft) 694 m (2277 ft) CS (RJ11) Signal Name Pin No. D1 POWH POWL D2 1 2 3 4 CSIF card (RJ45) Pin No. Signal Name 1 2 3 4 5 6 7 8 D1 POWH POWL D2 Accessories and User-supplied Items for the CS Accessories (included): Screws 2, Washers 2 User-supplied (not included): RJ11 connector Note For details about CSIF card, refer to "3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-
TDA0144)". 146 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations Using a DHLC/DLC Card Refer to the following example to connect a CS to the PBX. KX-TDA0158 DHLC8 Card Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance 222 m (728 ft) 347 m (1138 ft) 500 m (1640 ft) 347 m (1138 ft) CS (RJ45) Signal Name Pin No. DHLC/DLC card (Amphenol) Signal Name D1C D2C D1B D1A D2A D2B
1 2 3 4 5 6 7 8 Master D1C D2C D1D D2D D1E D2E Accessories and User-supplied Items for the CS Accessories (included): Screws 2, Washers 2 User-supplied (not included): RJ45 connector Notes
The no. 4 and no. 5 pins (Master) of the CS must be connected to a pair of pins on the DHLC/DLC card. Then use 3 consecutive pairs of pins on the DHLC/DLC card, starting with the pins corresponding to the Master, as in the example above. CS connections must be made within the same DHLC/DLC card. Installation Manual 147 3.9 Connection of 2.4 GHz Portable Stations KX-T0151/KX-T0141 DHLC8 Card Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance 222 m (728 ft) 347 m (1138 ft) 500 m (1640 ft) 347 m (1138 ft) CS (RJ11) Signal Name Pin No. D1 D2 1 2 3 4 Accessories and User-supplied Items for the CS Accessories (included): Screws 2, Washers 2 User-supplied (not included): RJ11 connector Note DHLC/DLC card (Amphenol) Signal Name D1 D2 For details about DHLC card or DLC card, refer to "3.6.2 DHLC8 Card (KX-TDA0170)", "3.6.3 DLC8 Card (KX-TDA0171)", or "3.6.4 DLC16 Card (KX-TDA0172)". 148 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations Connecting the CS 1. Connect the cable from the CSIF/DHLC/DLC card to the CS. KX-T0151/KX-TDA0152 KX-TDA0158 KX-T0141/KX-TDA0142 Modular Modular Modular To CSIF/DHLC/DLC card To DHLC/DLC card To CSIF/DHLC/DLC card 2. Pass the cable through the groove of the CS (in any direction depending on your preference). KX-T0151/KX-TDA0152 KX-TDA0158 KX-T0141/KX-TDA0142 To CSIF/DHLC/DLC card To DHLC/DLC card To CSIF/DHLC/DLC card Installation Manual 149 3.9 Connection of 2.4 GHz Portable Stations Registering the PS The PS must be registered to the PBX before it can be used. Programming of both the PS and PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required to perform the PBX system programming. Note For details about system programming using a PT, refer to "2.3.2 PT Programming" in the Feature Manual, and "2.1 PT Programming" in the PT Programming Manual. Entering the System Programming Mode PT (Administrator Level) PROGRAM/
PAUSE
System Password for Administrator for PT Programming Programming No.
= 1234 3 digits PS (Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695) Press POWER for 2 seconds. Select
"Setting Handset". Select
"System Option". If required System Lock Password 4 digits PS (Using the KX-TD7680) System Setting Menu FUNC Press POWER for 2 seconds. Select
"PS PROGRAM". Select
"SYSTEM SET". If required System Lock Password 4 digits PS (Using the KX-TD7690) System Setting Menu MENU S1 Press POWER for 2 seconds. Select
"PS PROGRAM". SEL S1 If required System Lock Password 4 digits ENTR S1 Select
"SYSTEM SETTING". System Setting Menu SEL S1 Note means default value throughout this section. 150 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations PS Registration
[690]
PS No. 001 to 128 Extn. No. 1 to 4 digits ENTER ENTER To the PS operation below END When the PS has not been registered yet When registering the PS for the first time, it is possible to select the desired language for the display.
(You do not need to enter the PS system programming mode when registering for the first time.) Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 Press POWER for 2 seconds. Select the desired language. Using the KX-TD7680 C.Tone C.Tone Press "F"
for 2 seconds.
[ F2 ]
[ F3 ]
Press POWER for 2 seconds. Press S2 repeatedly to select the desired language. Press S3 for 2 seconds. Using the KX-TD7690 F2 F3 Press POWER for 2 seconds. Press S2 repeatedly to select the desired language. Press S3 for 2 seconds. C.Tone C.Tone When the PS has already been registered to another PBX One PS can be registered to a maximum of 4 different PBXs. Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 Select
"Register H/set". Choose
"Base 14". Using the KX-TD7680 Select
"REGISTRATION". Choose
"SYSTEM 14". Using the KX-TD7690 C.Tone C.Tone Select
"REGISTRATION". SEL S1 SEL S1 C.Tone Choose
"SYSTEM 14". Installation Manual 151 3.9 Connection of 2.4 GHz Portable Stations Setting the System Lock When a system lock has been set, the system lock password will be required for PS system setting. Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 Select
"SYSTEM LOCK". Choose "On/Off". System Lock Password System Lock Password 4 digits 4 digits On Off C.Tone Using the KX-TD7680 Select
"SYSTEM LOCK". Choose
"Enable/Disable". System Lock Password System Lock Password 4 digits 4 digits ENABLE DISABLE C.Tone ENTR S1 System Lock Password 4 digits Using the KX-TD7690 SEL CHNG Select
"SYSTEM LOCK". S1 S1 Choose
"Enable/Disable". System Lock Password 4 digits SEL S1 ENTR S1 ENABLE DISABLE C.Tone 152 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations Setting the Personal Identification Number (PIN) for PS Registration To prevent registering the PS to a wrong PBX, a PIN for PS registration can be set to the PBX. Before registering the PS to the PBX, enter the PIN set to the PBX into the PS. By doing so, the PS will only be registered to the PBX with the matching PIN. Notes
By default, the PIN for PS registration is "1234" for both the PBX and PS. Therefore, the PS can be registered to the PBX without setting the PIN. The PIN for PS registration will only be used when registering the PS to the PBX. Therefore, during normal operation after registration, even if there is more than 1 PBX with the same PIN near the PS, the PS will not be inadvertently linked to a different PBX. Setting the PIN for PBX
[692]
PIN for PS Registration ENTER 4 digits 1234 ENTER END Setting the PIN for PS Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 Select
"Change PIN"
Using the KX-TD7680 Select
"CHANGE PIN"
Using the KX-TD7690 PIN for PS Registration 1 to 8 digits 1234 PIN for PS Registration 1 to 4 digits 1234 C.Tone C.Tone Select
"CHANGE PIN"
SEL S1 PIN for PS Registration 1 to 4 digits 1234 ENTR S1 C.Tone Installation Manual 153 3.9 Connection of 2.4 GHz Portable Stations PS Termination Confirm the following before cancelling the PS registration:
The PS is turned on. The PS is within range.
[691]
PS No. 001 to 128 ENTER If "Rejected" or "Time out" is displayed CLEAR YES Press "CLEAR". Press "YES". ENTER END To the PS operation below If the registration information is still stored in the PS Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695 Select "Cancel Base". Select "Base 1-4". Select "YES". C.Tone Using the KX-TD7680 Select "DELETE SYSTEM". Select the desired item. Select "YES". C.Tone Using the KX-TD7690 Select "DELETE SYSTEM". SEL S1 C.Tone SEL S1 SEL S1 Select the desired item. Select "YES". Testing the Operation Walk around the service area while having a conversation using a registered PS. If noise is frequent or conversations disconnect, relocate the CSs or install an additional CS. 154 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations 3.9.8 Wall Mounting Mounting the KX-T0151/KX-TDA0152/KX-TDA0158 1. Place the reference for wall mounting (KX-T0151/KX-TDA0152/KX-TDA0158) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. 2. Notes
Make sure that the screw heads are at the same distance from the wall.
Insert the upper and lower tabs of the wall mounting plate into the designated openings in the base unit. Install the screws perpendicular to the wall. 3. KX-T0151/KX-TDA0152 KX-TDA0158 Tabs Tabs 4. Slide the wall mounting plate in the direction of the arrow until it clicks. KX-T0151/KX-TDA0152 KX-TDA0158 5. Hook the CS on the screw heads. KX-T0151/KX-TDA0152 KX-TDA0158 83 mm 83 mm Installation Manual 155 3.9 Connection of 2.4 GHz Portable Stations Reference for Wall Mounting (KX-T0151/KX-TDA0152/KX-TDA0158) Please copy this page and use as a reference for wall mounting. Install a screw here. 83 mm
(3-1/4 in) Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here. 156 Installation Manual 3.9 Connection of 2.4 GHz Portable Stations Mounting the KX-T0141/KX-TDA0142 1. Place the reference for wall mounting (KX-T0141/KX-TDA0142) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. 2. Notes
Make sure that the screw heads are at the same distance from the wall.
Install the screws perpendicular to the wall. 3. Hook the CS on the screw heads. Installation Manual 157 3.9 Connection of 2.4 GHz Portable Stations Reference for Wall Mounting (KX-T0141/KX-TDA0142) Please copy this page and use as a reference for wall mounting. 71 mm
(2-13/16 in) Install a screw here. Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here. 158 Installation Manual 3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.10.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays The PBX supports a maximum of 16 doorphones, 16 door openers, 16 external sensors, and 16 external relays. Note Doorphones, door openers, external sensors, and external relays are user-supplied. Maximum Cabling Distance Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance 70 m (230 ft) 113 m (371 ft) 180 m (590 ft) 113 m (371 ft) Doorphone Door Opener External Sensor/
External Relay Device Installing the Doorphone (KX-T30865) 1. Loosen the screw to separate the doorphone into 2 halves. P a n a s o n i c Screw Installation Manual 159 3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays 2. Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws. Screw Note To 8-pin terminal block Two kinds of screws are included with a KX-T30865. Please choose the appropriate kind for your wall type.
: when a doorphone plate has been fixed to the wall
: when you wish to install the doorphone directly onto the wall 3. Connect the wires to the screws located in the front cover. 4. Re-attach the 2 halves and re-insert the screw. To 8-pin terminal block Connection Use 8-pin and 10-pin terminal blocks (included with the card) for connection. 1. While pressing down on the hole at the top of the terminal block using a screwdriver, insert the wire into the side hole as shown below. Repeat this procedure for other doorphones, door openers, external sensors, and external relays. Refer to "3.7.2 DPH4 Card (KX-TDA0161)" and "3.7.3 EIO4 Card (KX-TDA0164)" for pin assignments. Doorphone Door Opener External Sensor/
External Relay Device 160 Installation Manual 3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays 2. Attach the terminal blocks to the connectors of the DPH4/EIO4 card on the PBX. To doorphones/
door openers/
external sensors/
external relays Installation Manual 161 3.11 Connection of Peripherals 3.11 Connection of Peripherals 3.11.1 Connection of Peripherals Maximum Distance 5 m (16 ft) Maximum Distance 10 m (32 ft) 10 m (32 ft) 10 m (32 ft) 10 m (32 ft) Maximum Distance 10 m (32 ft) 10 m (32 ft) 10 m (32 ft) 10 m (32 ft) Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
Cable 26 AWG:
24 AWG:
22 AWG:
CAT 5:
RJ45
(for PC Maintenance) Maximum Distance 2 m (6 ft) RS-232C PC CTI Server BGM Music on Hold Pager:
Amplifier/Speaker PC Printer PC/CTI Server (via RJ45) The PBX is equipped with a RJ45 port for communicating between the PBX and a PC or CTI server. The PC can be used for system programming, diagnostics and external system database storage (save/
load) functions. The CTI server can be used for connecting PCs on a LAN to provide third party call control CTI. CTI connection uses the CSTA Phase 3 or TAPI 2.1 protocol. Note The operating system of the PC or CTI server required for third party call control depends on your CTI application software. For details, refer to the manual for your CTI application software. 162 Installation Manual 3.11 Connection of Peripherals Pin Assignments No. Signal Name Input (I)/Output (O) Function 8 1 1 2 3 4-5 6 7-8 TPO+
TPO-
TPI+
Reserved TPI-
Reserved O O I I Transmit data+
Transmit data-
Receive data+
Receive data-
BGM/MOH The PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g., user-
supplied radios) can be connected to the PBX. CAUTION
Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise, sound may only be heard intermittently. External Music Jacks are SELV ports and should only be connected to approved SELV devices.
Note When the PBX and external music sources are not connected to the same ground, hum noise may be induced into Background Music and Music on Hold. Pager Up to 2 paging devices (user-supplied) can be connected to the PBX. CAUTION External Paging Jacks are SELV ports and should only be connected to approved SELV devices. PC/Printer (via RS-232C) The PBX is equipped with an RS-232C interface. This interface provides communication between the PBX and the user-supplied devices such as PC or line printers. The RS-232C port is used for system programming, SMDR, diagnostics and external system database storage (save/load) functions. When using special accessories such as cable, the user should use those specified in this installation manual to comply with the limits for a Class B digital device pursuant to the FCC Rules. Note Use an RS-232C cross cable for connection between the PBX and PC. Installation Manual 163 3.11 Connection of Peripherals Pin Assignments No. Signal Name Function 6 1 9 5 2 3 4 5 6 7 8 RD (RXD) SD (TXD) ER (DTR) SG DR (DSR) RS (RTS) CS (CTS) Receive Data Transmit Data Data Terminal Ready Signal Ground Data Set Ready Request To Send Clear To Send Connection Charts For connecting a printer/PC with a 9-pin RS-232C connector Circuit Type EIA BB BA CD AB CC CA CB CCITT 104 103 108.2 102 107 105 106 Circuit Type
(EIA) BB BA CD AB CC CA CB PBX (9-pin) Signal Name RD (RXD) SD (TXD) ER (DTR) SG DR (DSR) RS (RTS) CS (CTS) Printer/PC (9-pin) Pin No. Pin No. 2 3 4 5 6 7 8 2 3 4 5 6 7 8 Signal Name RD (RXD) SD (TXD) ER (DTR) SG DR (DSR) RS (RTS) CS (CTS) Circuit Type
(EIA) BB BA CD AB CC CA CB 164 Installation Manual 3.11 Connection of Peripherals For connecting a printer/PC with a 25-pin RS-232C connector Circuit Type
(EIA) BB BA CD AB CC CA CB PBX (9-pin) Signal Name RD (RXD) SD (TXD) ER (DTR) SG DR (DSR) RS (RTS) CS (CTS) RS-232C Signals Printer/PC (25-pin) Pin No. Pin No. 2 3 4 5 6 7 8 1 3 2 20 7 5 6 4 Signal Name FG RD (RXD) SD (TXD) ER (DTR) SG CS (CTS) DR (DSR) RS (RTS) Circuit Type
(EIA) AA BB BA CD AB CB CC CF
Receive Data (RXD):(input) Conveys signals from the printer or the PC. Transmit Data (TXD):(output) Conveys signals from the unit to the printer or the PC. A "Mark" condition is held unless data or BREAK signals are being transmitted. Data Terminal Ready (DTR):(output) This signal line is turned ON by the unit to indicate that it is ON LINE. Circuit ER (DTR) ON does not indicate that communication has been established with the printer or the PC. It is switched OFF when the unit is OFF LINE. Signal Ground (SG) Connects to the DC ground of the unit for all interface signals. Data Set Ready (DSR):(input) An ON condition of circuit DR (DSR) indicates the printer or the PC is ready. Circuit DR (DSR) ON does not indicate that communication has been established with the printer or the PC. Request To Send (RTS):(output) This lead is held ON whenever DR (DSR) is ON. Clear To Send (CTS):(input) An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data from the unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is OFF. Frame Ground (FG) Connects to the unit frame and the ground conductor of the AC power cord. Installation Manual 165 3.12 LAN Connection 3.12 LAN Connection 3.12.1 LAN Connection Connection Chart for LAN Connection The PBX is equipped with an RJ45 port for connecting to a LAN so that IP telephones (IP-PTs, IP softphones, SIP Extensions), PCs and a CTI Server can be connected on a private IP network. IP Softphone PC RJ45
(for LAN Connection) CTI Server Switching Hub IP-PT SIP Extension Switching Hub Signal Name Pin No. TX+
TX-
RX+
RX-
1 2 3 6 PBX (RJ45) Pin No. Signal Name 1 2 3 6 RX+
RX-
TX+
TX-
Notes
Use an Ethernet straight cable with an RJ45 connector for connection to a switching hub. The cable should be a 10BASE-T/100BASE-TX CAT 5 or higher cable.
Make sure that all the CAT 5 cables in use are not over 100 m (328 ft) in length.
Make sure to create a spanning tree for LAN connection in order to prevent loops from occurring in a multi-bridged environment. Otherwise, some packets may circulate for long periods of time and eventually PBX performance system may degrade. 166 Installation Manual 3.13 Power Failure Connections 3.13 Power Failure Connections 3.13.1 Power Failure Connections When the power supply to the PBX fails, power failure transfer (PFT) will switch from the current connection to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Manual for further information. Connection Power Failure Connection connects a specific SLT and a CO line in the event of power failure. The following analog CO line and extension cards can be used for Power Failure Connections:
Analog CO line cards: LCOT16 (4 PFT ports) and LCOT8 (2 PFT ports) Extension cards: MSLC16 (4 PFT ports), SLC16 (4 PFT ports), DHLC8 (2 PFT ports) and SLC8
(2 PFT ports) To 1 analog CO line card, connect only 1 extension card. Note By programming the PBX, a CO line conversation established during power failure can be maintained even when the power returns and the connection is switched back to the normal configuration from the Power Failure Connection. However, if no special programming is performed, the connection will be dropped when power returns. RJ11 T2 T1 R1 R2 R2 R1 T1 T2 CO Line Card
(e.g., LCOT8) Extension Card
(e.g., SLC8) To CO line To SLT Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ11 connectors Installation Manual 167 3.13 Power Failure Connections RJ11 Connector Pin Assignments for Analog CO Line Card PFT Ports 1 and 2 No. Signal Name 1 4 1 2 3 4 R2 R1 T1 T2 PFT Ports 3 and 4 (for LCOT16 card only) No. Signal Name 1 4 1 2 3 4 R4 R3 T3 T4 Function Ring port 2 Ring port 1 Tip port 1 Tip port 2 Function Ring port 4 Ring port 3 Tip port 3 Tip port 4 RJ11 Connector Pin Assignments for Extension Card PFT Ports 1 and 2 No. Signal Name 1 4 1 2 3 4 T2 T1 R1 R2 Function Tip port 2 Tip port 1 Ring port 1 Ring port 2 PFT Ports 3 and 4 (for MSLC16/SLC16 card only) No. Signal Name 1 4 1 2 3 4 T4 T3 R3 R4 Function Tip port 4 Tip port 3 Ring port 3 Ring port 4 168 Installation Manual 3.14 Starting the PBX 3.14 Starting the PBX 3.14.1 Starting the PBX CAUTION
SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before startup. Before touching the System Initialize Switch, discharge static electricity by touching ground or wearing a grounding strap. Once you have started the PBX and if you unplug the PBX, do not perform the following procedures to start the PBX again. Otherwise, your programmed data is cleared. To restart the PBX, refer to
"5.1.4 Using the Reset Button". The PBX will continue to be powered even if the power switch is turned "OFF". The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located near the equipment and is easily accessible. System Initialization Procedure 1. Slide the System Initialize Switch to the "SYSTEM INITIALIZE" position. RUN Indicator Reset Button RESET SYSTEM INITIALIZE NORMAL System Initialise Switch Installation Manual 169 3.14 Starting the PBX 2. Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will flash. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. To AC Outlet 3. While the RUN indicator is flashing, slide the System Initialize Switch back to the "NORMAL" position. Depending on the configuration, initialization takes about 1 min to 3 min. If successfully executed, the RUN indicator will stop flashing and stay lit. All data will be cleared, and the PBX as well as all optional service cards (except for the IP-GW card) will be initialized to the default values. The DPTs should show the time as 01:00. The data of the IP-GW card will not be initialized. Note Use only the AC power cord included with the PSU. LED Indications Indication RUN Color Green Description PBX status indication
OFF: Power Off (includes normal reset) ON: Power On and running (on-line) Flashing (60 times per minute): Starting up Flashing (120 times per minute): Starting up or resetting with:
the System Initialize Switch in "SYSTEM INITIALIZE"
position the SD Memory Card not inserted
ALARM Red Alarm indication
OFF: Normal ON: Alarm (CPU stop, alarm for each optional service card) Flashing: Alarm (IPCMPR file error in restarting) Confirming the CO Line Connection After initialization, program the PBX and connect CO lines to the PBX. To confirm that the CO lines are successfully connected, dial [
or press the PT's S-CO button. You will hear a dial tone if the CO line is available and connected.
] [3] [7] + CO line number (3 digits) on a PT, 170 Installation Manual Section 4 Guide for the KX-TDE Maintenance Console Explains the installation procedure, structure, and basic information of the KX-TDE Maintenance Console. Installation Manual 171 4.1 Overview 4.1 Overview 4.1.1 Overview KX-TDE Maintenance Console is designed to serve as an overall system programming reference for the PBX. To program and administer the PBX by PC, you need to install the KX-TDE Maintenance Console onto the PC. This section describes overview and installation of the KX-TDE Maintenance Console only. KX-TDE Maintenance Console*1 Menu Bar System Menu
*1 The contents and design of the software are subject to change without notice. 172 Installation Manual 4.2 Connection 4.2 Connection 4.2.1 Connection LAN Connection via RJ45 Port of IPCMPR Card RJ45 (for LAN Connection) Switching Hub To network port PC Note For pin assignments and maximum cabling distance, refer to "3.11.1 Connection of Peripherals". Serial Interface Connection RJ45 (for PC Maintenance) To LAN Port To COM Port PC PC Note RS-232C Port For pin assignments and maximum cabling distance, refer to "3.11.1 Connection of Peripherals". Installation Manual 173 4.2 Connection External Modem Connection Modem To RS-232C port (25-pin) To CO line/PBX extension port assigned as the CO line destination RS-232C Port
(9-pin) External Modem (25-pin) Signal Name Pin No. RD (RXD) SD (TXD) ER (DTR) DR (DSR) 3 2 20 6 PBX (9-pin) Pin No. Signal Name 2 3 4 6 RD (RXD) SD (TXD) ER (DTR) DR (DSR) After connecting the PBX and the external modem, set the power switch of the external modem to "ON", then the external modem will be initialized with the default values. The following AT command settings may be required for the modem:
The Data Terminal Ready (DTR) signal should be ignored. The Data Terminal Equipment (DTE)/Modem flow control should be turned off. Data compression should be disabled. Error Correction is not necessary.
Notes
Use an RS-232C straight cable for connection between the PBX and external modem. An AT command (for initialization, enabling automatic answer, etc.) can only be programmed by KX-TDE Maintenance Console. "AT&F" is stored as the default value. For more information about the AT command, refer to the external modem's instructions. 174 Installation Manual 4.3 Installation of the KX-TDE Maintenance Console 4.3 Installation of the KX-TDE Maintenance Console 4.3.1 Installing and Starting the KX-TDE Maintenance Console System Requirements Required Operating System
Microsoft Windows 2000, Windows XP, or Windows Vista Minimum Hardware Requirements
CPU: 300 MHz Intel HDD: 100 MB of available hard disk space RAM: 128 MB of available RAM Celeron microprocessor Installing the KX-TDE Maintenance Console Notes
Make sure to install and use the latest version of the KX-TDE Maintenance Console.
To install or uninstall the software on a PC running Windows 2000 Professional or Windows XP Professional, you must be logged in as a user in either the "Administrators" or "Power Users" group. 1. Copy the setup file of the KX-TDE Maintenance Console to your PC. (Its icon is shown here, on the left.) 2. Double-click the setup file to run the installer. 3. Follow the on-screen instructions provided by the installation wizard. Starting the KX-TDE Maintenance Console and Assigning the Basic Items (Quick Setup) When you start the KX-TDE Maintenance Console with the Installer Level Programmer Code and connect to the PBX for the first time after initialization (with the factory default setting), Quick Setup will launch automatically. During Quick Setup, you will set up the basic items. For details about the basic items, refer to
"2.3.4 Quick Setup" in the Feature Manual. 1. Connect the PC to the PBX with an Ethernet straight cable or RS-232C. 2. Start the KX-TDE Maintenance Console from the Start menu. 3.
"Information before programming" appears. a. Carefully read this important additional information, which includes updates to this and other manuals. b. Click OK to close this window. Installation Manual 175 4.3 Installation of the KX-TDE Maintenance Console 4. a. Enter the Installer Level Programmer Code (default: INSTALLER). The Programmer Code authorizes different programming levels, and the Quick Setup is only available when you start the KX-TDE Maintenance Console with the Installer Level Programmer Code. Note There are 2 other Programmer Codes with limited authorisation: Administrator Level (default:
ADMIN), and User Level (default: USER). b. Click OK. 5. a. Click Connect LAN or RS-232C from the menu bar, depending on the serial interface connection with the PBX. In the next screen, enter the system password for installer (default: 1234). b. c. Click OK. 6. Follow the instructions of the Quick Setup wizard and assign the basic items (Quick Setup). The system menu appears. You may now begin programming the PBX. Notes
During a long programming session, it is highly recommended that you periodically save the system data to the SD Memory Card. If the PBX undergoes a sudden power failure or if the system is reset for some reason, all the system data in RAM will be lost. However, if system data has been saved to the SD Memory Card, it can be easily restored. To save the system data to the SD Memory Card, (1) click the "SD Memory Backup" icon before resetting the PBX or turning off the power, or (2) exit the KX-TDE Maintenance Console so that the PBX automatically saves the system data.
When programming PBX data which can be displayed on a proprietary telephone (PT) (extension names, group names, System Speed Dialing names, etc.), it is possible to enter characters which cannot be displayed on a KX-T7600 series PT. Characters which can be displayed on a KX-T7600 series PT are shown below in the white cells. 176 Installation Manual 4.3 Installation of the KX-TDE Maintenance Console
The PC will not perform any shutdown operation, or enter the power-saving system standby mode while the KX-TDE Maintenance Console is connected to the PBX. To perform either of the operations above, first close the connection to the PBX. CAUTION Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX to fail to start when you try to restart the system. Installation Manual 177 4.3 Installation of the KX-TDE Maintenance Console 178 Installation Manual Section 5 Troubleshooting This section provides information on the PBX and telephone troubleshooting. Installation Manual 179 5.1 Troubleshooting 5.1 Troubleshooting 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION You cannot make/receive calls via an IP network. IP-PTs/SIP Extensions do not operate.
IP-EXT/IP-GW/DSP card malfunction IPCMPR card malfunction
Not enough activation keys Replace the corresponding card. Replace the IPCMPR card (be sure to turn off the PBX when replacing). Purchase additional activation key cards. Please consult a certified dealer for details. Poor connection
Make sure that an 8-pin twisted pair cable is used for connection.
Make sure that none of the CAT 5 cables in use are over 100 m (328 ft) in length.
Make sure that a straight cable is used for connection to a switching hub. Network malfunction
Make sure that all network devices in use are switched on.
Make sure that there is no unwanted firewall in the IP network. IP-EXT/DSP card malfunction IPCMPR card malfunction
Not enough activation keys IP-PT/SIP Extension not registered IP-PT/SIP Extension malfunction
Replace the corresponding card. Replace the IPCMPR card (be sure to turn off the PBX when replacing). Purchase additional activation key cards. Please consult a certified dealer for details. Register the corresponding IP-PT/SIP Extension. Replace the IP-PT/SIP Extension. Poor connection
Make sure that an 8-pin twisted pair cable is used for connection.
Make sure that none of the CAT 5 cables in use are over 100 m (328 ft) in length.
Make sure that a straight cable is used for connection to a switching hub. 180 Installation Manual PROBLEM PROBABLE CAUSE SOLUTION
Network malfunction
Make sure that all network devices in 5.1 Troubleshooting use are switched on.
Make sure that the IP-PT/SIP Extension is not blocked by the firewall or other network devices. Extension card malfunction Replace the corresponding card. Poor connection between the PBX and the extension
Take the extension and plug it into the same extension port using a short telephone cord. If the extension works, then the connection between the PBX and the extension must be repaired. A telephone with an A-A1 relay is connected.
Make sure that a 2-wire cord is used.
Make sure that the A-A1 relay switch of Extension malfunction Extensions (except IP-PT/SIP Extension) do not operate.
Wrong type of PSU The PBX does not operate properly. Noise on external paging. Distorted external music. Alternate CallingRing/Voice and Live Call Screening (LCS) do not function as set when using a Wireless Phone (KX-T7880/
KX-T7885/KX-TD7894/KX-
TD7895). The ALARM indicator on the front of the shelf turns on red.
Induced noise on the wire between the PBX and the amplifier. Excessive input level from external music source. Voice-calling mode and Hands-free mode with LCS are not available with Wireless Phones. A major system error occurs in the PBX.
the telephone is in "OUT" or "OFF"
position. Take the extension and plug it into another extension port that is working. If the extension does not work, replace the extension. Replace the PSU with the appropriate type. Press the Reset Button (refer to "5.1.4 Using the Reset Button"). Turn off the power switch, and then turn it back on. Turn off the power switch, and then unplug the PBX. After 5 minutes, plug the PBX back in, and turn the power switch back on. Use a shielded cable as the connection wire between the PBX and amplifier. A short shielded cable is recommended. Decrease the output level of the external music source by using the volume control on the music source. Switch the calling mode to ring-calling. Set the LCS mode to "Private". See the error log using the KX-TDE Maintenance Console (refer to "5.1.5 Troubleshooting by Error Log"). Installation Manual 181 5.1 Troubleshooting PROBLEM The LINK indicator of the IP-
EXT/IP-GW/IPCMPR does not turn on. PROBABLE CAUSE IP-EXT/IP-GW card malfunction IPCMPR card malfunction
SOLUTION Replace the corresponding card. Replace the IPCMPR card (be sure to turn off the PBX when replacing). Poor connection
Make sure that an 8-pin twisted pair
cable is used for connection.
Make sure that none of the CAT 5 cables in use are over 100 m (328 ft) in length.
Make sure that a straight cable is used for connection to a switching hub.
Network malfunction
Make sure that all network devices in use are switched on. 182 Installation Manual 5.1.2 Connection 5.1 Troubleshooting Can you dial an extension?
No Connection between the PBX and a PT:
CAUSE SOLUTION Use the correct cord (the inner 2 wires are for T/R and the outer 2 wires are for D1/D2) The T/R is connected to the D1/D2. D1 T R D2 D1 T R D2 PBX Extension Connection between the PBX and an SLT:
CAUSE SOLUTION The T/R is connected to the D1/D2. D1 T R D2 T R PBX Extension Use the correct cord (the inner 2 wires are for T/R). If a telephone equipped with an A-A1 relay is connected to the PBX, set the A-A1 relay switch of the telephone to "OFF". Yes Connection between the PBX and an SLT that is polarity-sensitive:
CAUSE The "T" is connected to the "R". SOLUTION Reverse the connections of the T/R. D1 T R D2 T R PBX Extension
(Continued on the next page.) Installation Manual 183 5.1 Troubleshooting
(Continued from the previous page.) Can you dial out on a CO line?
No Connection between the central office and the PBX:
SOLUTION Reconnect the CO line to the T1/R1 or T2/R2 of the telephone jack using 2-
conductor wiring. CAUSE CO line is connected to the T2/T1. T2 R1 T1 R2 CO line PBX CO line is connected to the T2/R1. T2 R1 T1 R2 CO line PBX 184 Installation Manual 5.1 Troubleshooting 5.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION
Cannot set the IP address, subnet mask address, and PBX IP address to the IP-
PT.
An unusable value is being set.
Set an IP address within the valid range. IP address of the IP-PT/PBX:
"1.0.0.0" to "223.255.255.255" Subnet mask address: "1.0.0.0" to
"255.255.255.254"
Cannot register the IP-PT.
The necessary network parameters are not set to the IP-PT.
When not using a DHCP server, set the IP address, subnet mask address, and enter the PBX IP address. If necessary, also enter the IP address of the default gateway.
When using a DHCP server, enter the PBX IP address.
The IP-PT cannot connect to the PBX.
When using the speakerphone on an APT, nothing is audible.
When using the speakerphone/monitor mode with a DPT, nothing is audible.
The PT does not ring. During a power failure, extensions connected to ports 1 to 4 of MSLC16/
SLC16 and ports 1 to 2 of DHLC8/SLC8 cards do not operate. Originating an outside call, call transfer, or conference cannot be performed. The wrong IP address, subnet mask address, PBX IP address, or default gateway address was entered. The Ethernet cable is not connected correctly. The DHCP server is not active.
Check each parameter and enter the correct value. Check the Ethernet cable connections. Restart the DHCP server. Disable DHCP and re-enter settings as appropriate. The HANDSET/HEADSET selector is set to the
"HEADSET" position.
When the headset is not used, set the HANDSET/HEADSET selector to the
"HANDSET" position. The "HEADSET" mode is selected by Personal Programming, "Handset/
Headset Selection". The ringer volume is off. A DPT or APT is connected to the extension port. The dialing mode (tone or pulse) is incorrect. The corresponding flexible button does not exist on the PT.
When the headset is not used, select the "HANDSET" mode by Personal Programming.
Turn on the ringer volume. Disconnect the DPT or APT and connect an SLT. Set the Tone/Pulse switch to the other position. Programme the flexible button. Refer to
"1.20.2 Flexible Buttons" in the Feature Manual. Installation Manual 185 5.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION
Cannot register the PS.
Wrong Personal Identification Number (PIN) is registered to the PS. CS is not connected properly.
Enter the PIN set to the PBX into the PS.
Make sure that the cable is connected properly with correct pin assignments. Also, make sure that the cable does not make short circuits. Switch all DIP switches off.
CSIF card is not working.
Install the CSIF card properly. CS is not working. Location of CS is not good. Access system of the PS is not properly set. Call handover is not working. PS is out of CS coverage area. It may take about 20 s for CS to start up after the status has been changed to In Service.
Make sure that the cable is connected properly with correct pin assignments. Also, make sure that the cable does not make short circuits. Switch all DIP switches off.
Locate the CS properly (refer to "3.9.5 Site Survey" ). Change the access system setting of the PS to the appropriate system or automatic. Locate the CS properly (refer to "3.9.5 Site Survey" ).
Wait until the CS starts up.
PS becomes out of range. Cannot make calls using the PS. Noise is frequent while using the PS. Conversations disconnect while using the PS. PS stays out of service when the CS status is changed from Out of Service to In Service. 186 Installation Manual 5.1.4 Using the Reset Button 5.1 Troubleshooting If the PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. CAUTION In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD ACCESS" LED is off before pressing the Reset Button. Notes
When the System Initialize Switch is set to "NORMAL", pressing the Reset Button causes the following:
Camp-on is cleared. Calls on hold are terminated. Calls on exclusive hold are terminated. Calls in progress are terminated. Call park is cleared. Other data stored in memory, except the above, are not cleared. Be aware that pressing the Reset Button with the System Initialize Switch in the "SYSTEM INITIALIZE" position clears all data stored in the PBX. Do not perform this operation unless you intend to delete all data from the PBX.
Operation If the PBX does not operate properly:
1. Slide the System Initialize Switch to the "NORMAL" position. 2. Press the Reset Button for about 1 second. RUN Indicator LED Reset Button System Initialize Switch Installation Manual 187 5.1 Troubleshooting 5.1.5 Troubleshooting by Error Log When a major system error occurs in the PBX, the ALARM indicator on the front of the shelf turns on red, and the system logs the error information. Error Log Display Format Below is the display format of the error log. For information about how to view the error log using the KX-
TDE Maintenance Console, refer to "2.5.8 UtilityError Log" in the PC Programming Manual. Example: KX-TDE Maintenance Console 3 7 1 2 4 5 6 Example: Station Message Detail Recording (SMDR) 07/01/01 10:37AM MJ ALM #000 10000 MPR WDT overflow 07/01/01 11:07AM MN ALM #010 10000 AC power down 07/01/01 03:55PM MN ALM #301 10501 Digital trunk RAI reception 1 2 3 4 5 6 Description 1 2 3 Date Time Level Item Description The date of the error detection. The time of the error detection. Minor (MN ALM) Major (MJ ALM) Displays minor errors, which affect only a certain part of system operation. Displays major errors, which affect operation of the whole system, or result in system failure. 4 Error Code The 3-digit error code assigned by the PBX. 188 Installation Manual Item Description 5 Sub Code The 5-digit sub code of the relevant hardware (XYYZZ). 5.1 Troubleshooting
Physical shelf: " " (blank) Virtual shelf: "*" (asterisk) X: Shelf type YY: Slot number KX-TDE100 (Physical slot): 00 to 06
(00: IPCMPR Card Slot; 01 to 06: Free Slots) KX-TDE200 (Physical slot): 00 to 11
(00: IPCMPR Card Slot; 01 to 11: Free Slots) KX-TDE100/KX-TDE200 (Virtual slot): 01 to 08
(01 to 04: Virtual CO Line Slots; 05 to 08: Virtual Extension Slots) ZZ: Port number For optional service cards except OPB3 card:
Port number (01 to 16) will be displayed. For OPB3 card:
Sub slot number (1 to 3) + port number (1 to 4) will be displayed as follows:
Sub slot 1 of OPB3: 11 to 14 Sub slot 2 of OPB3: 21 to 24 Sub slot 3 of OPB3: 31 to 34 Note When there is no parameter for slot and port number, YY and ZZ will be displayed as "00". Example: Sub code for IPCMPR card = " 0000"
6 7 Error Message Log Information A description of the error. Displays probable causes of the errors and their solutions. Installation Manual 189 5.1 Troubleshooting 190 Installation Manual Index Installation Manual 191 Index 29, 119 Numerics 16-Channel Echo Canceller Card (KX-TDA0166) 16-Channel SIP Extension Activation Key (KX-NCS4716) 16-Channel VoIP DSP Card (KX-TDE0110) 16-Channel VoIP Extension Card (KX-TDA0470) 16-Channel VoIP Gateway Card (KX-TDA0490) 16-Port Analog Trunk Card (KX-TDA0181) 16-Port Digital Extension Card (KX-TDA0172) 30, 109 16-Port Single Line Telephone Extension Card (KX-TDA0174) 16-Port Single Line Telephone Extension with Message Lamp Card (KX-
30, 111 30, 94 29, 104 29, 82 30, 85 44 TDA0175) 30, 109 145 137 146 131 129 133 141 2.4 GHz Portable Station, After Site Survey 2.4 GHz Portable Station, Before Site Survey 2.4 GHz Portable Station, Connecting a CS 2.4 GHz Portable Station, Procedure Overview 2.4 GHz Portable Station, Radio Method 2.4 GHz Portable Station, Site Planning 2.4 GHz Portable Station, Site Survey 4 Cell Station Interface Card (KX-TDA0143) 4-Channel IP Trunk Activation Key (KX-NCS4104) 4-Channel Message Card (KX-TDA0191) 4-Channel VoIP Gateway Card (KX-TDA0484) 29, 114 4-Port Doorphone Card (KX-TDA0161) 4-Port External Input/Output Card (KX-TDA0164) 64-Channel VoIP DSP Card (KX-TDE0111) 8 Cell Station Interface Card (KX-TDA0144) 8-Channel IP Proprietary Telephone Activation Key (KX-NCS4508) 8-Channel IP Softphone/IP Proprietary Telephone Activation Key (KX-
29, 82 29, 96 30, 120 29, 116 29, 96 30, 92 44 NCS4208) 44 8-Port Analog Trunk Card (KX-TDA0180) 8-Port Caller ID Card (KX-TDA0193) 8-Port Digital Extension Card (KX-TDA0171) 29, 99 8-Port Digital Hybrid Extension Card (KX-TDA0170) 8-Port Single Line Telephone Extension Card (KX-TDA0173) 29, 102 30, 87 30, 85 44 30, 106 A About the software version of your PBX 42 Activation Key Activation Key Card Activation Key File Activation Key for Software Upgrade to Enhanced Version (KX-
44 43, 45 12 NCS4910) 44 42 43 Activation Key, in the DSP16/DSP64 Card Activation Key, in the SD Memory Card 42 Activation Key, Maximum Number 68, 69 Amphenol Connector Attaching to an Amphenol Connector Attaching to an RJ45 Connector 66 67 3 26 B Basic CS Basic Shelf Basic Shelf, Construction BGM Blank Slot Cover (KX-A258) 163 26 61 C Cable Distance 121 192 Installation Manual 62 33 87 35 35, 84 170 2 Cable Handling Characteristics CID8 Card (KX-TDA0193) CO Line Card, Physical CO Line Card, Virtual CO Line Connection Components, System Connection Chart for LAN Connection 27 Connection Diagram, System Connector Types Cover for Blank Slot CS (for 2.4 GHz Portable Station) 3 CS, Basic CS, High-density CSIF4 Card (KX-TDA0143) CSIF8 Card (KX-TDA0144) CTI Server Connection (via USB version 2.0) CTIFirst Party Call Control CTIThird Party Call Control 128 162 96 96 146 64 61 3 166 162 99 126 D DHLC8 Card (KX-TDA0170) Digital EXtra Device Port (Digital XDP) Connection Digital XDP Digital XDP Connection, Using a Modular T-Adaptor Digital XDP Connection, Using an EXtra Device Port DLC16 Card (KX-TDA0172) DLC8 Card (KX-TDA0171) 114, 159 Door Opener 114, 159 Doorphone DPH4 Card (KX-TDA0161) DSP16 Card (KX-TDE0110) DSP64 Card (KX-TDE0111) 104 102 114 82 82 126 126 127 188 119 116 E ECHO16 Card (KX-TDA0166) Editing the CS Name using the KX-TDE Maintenance Console EIO4 Card (KX-TDA0164) Error Log 108 EXT-CID Card (KX-TDA0168) Extension Caller ID Card (KX-TDA0168) Extension Card, Physical Extension Card, Virtual External Relay External Sensor EXtra Device Port (XDP) Mode 35 35, 84 116, 118, 159 116, 118, 159 29, 108 124, 126 97 66 F Ferrite Core First Party Call Control CTI Connection Floor Standing (KX-TDE200 Only) 58 Frame ground Connection 53 Front Cover, Closing 52 Front Cover, Opening 74 128 H High-density CS 3 Index Load Figure Calculation L-Type Power Supply Unit (KX-TDA0103) 38 29, 54 172 M Maintenance Console Master DPT, Digital XDP MOH MSG4 Card (KX-TDA0191) MSLC16 Card (KX-TDA0175) M-Type Power Supply Unit (KX-TDA0104) 120 163 109 126 N Names and Locations 51 113 O OPB3 Card (KX-TDA0190) Optional 3-Slot Base Card (KX-TDA0190) Optional Equipment 59 Optional Service Card, Installation Optional Service Card, Maximum Number Optional Service Card, Removal 29 63 29, 54 30, 113 35 4 4 124 124 163 162 124, 126 10 P Pager Panasonic Proprietary Telephones, Compatible Panasonic Proprietary Telephones, Incompatible 123 Parallel Connection of the Extensions Parallel Connection, Using a Modular T-Adaptor Parallel Connection, Using an EXtra Device Port Parallel Mode Password Security 163 PC Connection (via RS-232C) PC Connection (via USB version 2.0) Peer-to-peer Connection Physical CO Line Card Physical Extension Card Power Failure Connections 54 Power Supply Unit Power Supply Unit Selection Power Supply Unit, Installation Power Supply Unit, Replacement PRI Card (PRI23) (KX-TDA0290) 90 PRI23 Card (KX-TDA0290) Printer Connection (via RS-232C) 54 PSU PSU Capacity PSU-L PSU-M PSU-S 38, 54 38, 54 38, 54 23 35 35 56 30, 90 38 55 163 167 39 48 84 I Information about the Virtual Cards Installation Precautions IP Convergence Main Processing Card (IPCMPR Card) IPCMPR Card IPCMPR Card Slot IP-EXT16 Card (KX-TDA0470) IP-GW16 Card (KX-TDA0490) IP-GW4E Card (KX-TDA0484) 111 94 92 79 34 79 K Key Management System KX-A258 (Blank Slot Cover) KX-NCS4104 (4-Channel IP Trunk Activation Key) KX-NCS4208 (8-Channel IP Softphone/IP Proprietary Telephone Activation 44 61 44 KX-NCS4508 (8-Channel IP Proprietary Telephone Activation Key) 44 KX-NCS4716 (16-Channel SIP Extension Activation Key) KX-NCS4910 (Activation Key for Software Upgrade to Enhanced 44 Key) 44 Version) 44 29, 54 29, 54 29, 54 29, 96 29, 96 KX-TDA0103 (L-Type Power Supply Unit) KX-TDA0104 (M-Type Power Supply Unit) KX-TDA0108 (S-Type Power Supply Unit) KX-TDA0143 (4 Cell Station Interface Card) KX-TDA0144 (8 Cell Station Interface Card) KX-TDA0161 (4-Port Doorphone Card) KX-TDA0164 (4-Port External Input/Output Card) KX-TDA0166 (16-Channel Echo Canceller Card) 29, 108 KX-TDA0168 (Extension Caller ID Card) KX-TDA0170 (8-Port Digital Hybrid Extension Card) KX-TDA0171 (8-Port Digital Extension Card) KX-TDA0172 (16-Port Digital Extension Card) 30, 106 KX-TDA0173 (8-Port Single Line Telephone Extension Card) 30, 109 KX-TDA0174 (16-Port Single Line Telephone Extension Card) KX-TDA0175 (16-Port Single Line Telephone Extension with Message Lamp 29, 102 29, 104 29, 116 29, 119 29, 114 29, 99 Card) 30, 109 30, 85 30, 85 30, 87 30, 83 30, 113 30, 120 KX-TDA0180 (8-Port Analog Trunk Card) KX-TDA0181 (16-Port Analog Trunk Card) 30, 88 KX-TDA0187 (T-1 Trunk Card) KX-TDA0190 (Optional 3-Slot Base Card) KX-TDA0191 (4-Channel Message Card) KX-TDA0193 (8-Port Caller ID Card) KX-TDA0196 (Remote Card) KX-TDA0290 (PRI Card [PRI23]) KX-TDA0470 (16-Channel VoIP Extension Card) KX-TDA0484 (4-Channel VoIP Gateway Card) KX-TDA0490 (16-Channel VoIP Gateway Card) KX-TDE Maintenance Console, Connection KX-TDE Maintenance Console, Installation KX-TDE Maintenance Console, Overview 175 KX-TDE Maintenance Console, Quick Setup KX-TDE Maintenance Console, System Requirements 29, 82 KX-TDE0110 (16-Channel VoIP DSP Card) 29, 82 KX-TDE0111 (64-Channel VoIP DSP Card) 173 175 172 30, 90 30, 111 30, 92 30, 94 L LCOT16 Card (KX-TDA0181) LCOT8 Card (KX-TDA0180) 170 LED Indications, PBX 85 85 175 Q Quick Setup 175 R Radio Method, 2.4 GHz Portable Station 30, 83 Remote Card (KX-TDA0196) Reset Button RMT Card (KX-TDA0196) 187 83 129 Installation Manual 193 Index RUN Indicator 169 133 141 34 48 126 54 79 109 106 34 S Safety Installation Instructions Safety Instructions SD Memory Card Site Planning, 2.4 GHz Portable Station Site Survey, 2.4 GHz Portable Station Slave DPT, Digital XDP SLC16 Card (KX-TDA0174) SLC8 Card (KX-TDA0173) Slot for the IPCMPR Card Slots for Physical Cards (Free Slots) 34 Slots for Virtual CO Line Cards 34 Slots for Virtual Extension Cards Specifications Specifications, Characteristics Specifications, General Description Specifications, System Capacity Starting the PBX S-Type Power Supply Unit (KX-TDA0108) Surge Protector Installation System Capacity System Components Table System Connection Diagram System Highlights System Initialization Procedure System Initialize Switch System Requirements 169, 187 175 2 27 169 169 76 31 34 33 22 34 31 29, 54 T 88 T1 Card (KX-TDA0187) 30, 88 T-1 Trunk Card (KX-TDA0187) Terminal Equipment, Maximum Number 188 Troubleshooting, by Error Log 183 Troubleshooting, Connection 180 Troubleshooting, Installation 185 Troubleshooting, Operation Troubleshooting, Using the Reset Button 37 187 U Unpacking 50 V V-IPEXT32 (Virtual 32-Channel VoIP Extension Card) V-IPGW16 (Virtual 16-Channel VoIP Gateway Card) Virtual 16-Channel VoIP Gateway Card (V-IPGW16) Virtual 32-Channel SIP Extension Card (V-SIPEXT32) Virtual 32-Channel VoIP Extension Card (V-IPEXT32) 84 Virtual Cards Virtual CO Line Card Virtual CO Line Slot Virtual Extension Card Virtual Extension Slot V-SIPEXT32 (Virtual 32-Channel SIP Extension Card) 35, 84 34 35, 84 34 W Wall Mounting (CS) 155 194 Installation Manual Wall Mounting (KX-TDE100) Wall Mounting (KX-TDE200) Wiring Precautions 48 72 70 84 84 84 84 84 84 Index Installation Manual 195 Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Puerto Rico, Inc. San Gabriel Industrial Park, Ave. 65 de Infantera, Km. 9.5, Carolina, Puerto Rico 00985 http://www.panasonic.com/csd Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. 2007 Panasonic Communications Co., Ltd. All Rights Reserved. PSQX4179ZA KK0507EK0 (v0.001)
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-06-05 | 2401.056 ~ 2479.68 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-06-05
|
||||
1 | Applicant's complete, legal business name |
Panasonic Corporation of North America
|
||||
1 | FCC Registration Number (FRN) |
0003762242
|
||||
1 | Physical Address |
Two Riverfront Plaza, 9th Floor
|
||||
1 |
Newark, New Jersey 07102-5490
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
ACJ
|
||||
1 | Equipment Product Code |
96NKX-TDA1052
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
B**** B******
|
||||
1 | Title |
Project Manager
|
||||
1 | Telephone Number |
201-3********
|
||||
1 | Fax Number |
201-3********
|
||||
1 |
B******@us.panasonic.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 2.4GHz CELL STATION | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 | Name |
T******** L******
|
||||
1 | Telephone Number |
877-7********
|
||||
1 | Fax Number |
905-8********
|
||||
1 |
t******@ultratech-labs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 68 | 2401.05600000 | 2479.68000000 | 0.1860000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC