Installation Manual This PCB assy with is to be installed only by the professionals and used only with a Car Audio produced by Panasonic Co., Ltd. When this PCB assy with Bluetooth for car audio is installed in the Car Audio, we shall consider the following points;
1. Since Model YEAP01A446, YEAP01A473 owns its FCC ID Number / IC Number, we shall affix an exterior label on the outside of the product if the FCC ID Number and IC Number are not visible. The exterior label shall use wording such as either Contained Transmitter Module FCC ID: ACJ932YEAP01A446 , Contained Transmitter Module ID:
ACJ932YEAP01A446, Contained IC: 216J- YEAP01A446 YEAP01A446, requirements of sub-sections 15.19(a)(3) in FCC Rules Part 15 Subpart C. The manual statement (15.19 (a)(3) is included User Guide of the product. YEAP01A446, YEAP01A473, is to be installed only by the professional line operator as shown in following pictures. (Fig 1 and 2) YEAP01A473, complies with IC: 216J-YEAP01A446 or Contained FCC 2. 3. Fig 1. Rear side of YEAP01A446, YEAP01A473 Bluetooth Module Bluetooth Antenna Connecter Fig 2. Top view of YEAP01A446, YEAP01A473 be equipped for a Car Audio (example) Fig 3. Top view of YEAP01A446, YEAP01A473 be equipped for a Car Audio (example) Fig 4. Front view of YEAP01A446, YEAP01A473 be equipped for a Car Audio (example) There isnt an official user manual for this PCB assy with Bluetooth YEAP01A446, YEAP01A473. However, user manuals of final product which have the module, must contain notification corresponding to the following description. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Properly shielded a grounded cables and connectors must be used for connection to host computer and / or peripherals in order to meet FCC emission limits. This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and persons body (excluding extremities: hands, wrists, feet and ankles). Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List The following antennas are installed to this Bluetooth Module Assy. Model name Manufacturer Type N1KYYYY00019 Monopole antenna N1KYYYY00030 Monopole antenna NISSEI ELECTRONIC Co., LTD. NISSEI ELECTRONIC Co., LTD. Antenna gain
(with cable loss)
-3.8dBi Cable loss Connector type 0.165dB U.FL
(Coaxial connector)
-4.4dBi 0.743dB U.FL
(Coaxial connector)